Theory · D1 Licence - Minibus · Module 10 of 18

Minibus dimensions and masses

You learn to check your minibus’s dimensions, total mass and axle load distribution against the limits of D1. You study projecting loads, vehicle combinations, restriction signs and the speed limiter.

34 min read24 sectionsReviewed Nov 3, 2026
A green two-axle minibus stands on a weighbridge beneath a gantry in an inspection area beside a road.
Checking minibus dimensions and masses

1Tare, mass in running order and laden mass

A green minibus parked beside the kerb shows seated passengers and several suitcases in the open luggage compartment.
The key idea

Distinguish your vehicle’s empty mass, ready-to-drive mass and actual loaded mass.

75 kgStandard driver
75 kgAttendant, if carried
TermWhat you count
TareVehicle, fixed equipment and supplies; no people or cargo
Mass in running orderTare, standard driver and standard attendant if carried
Laden massActual journey mass, including people and cargo

Remember

  • Add the standard driver’s mass to tare to calculate mass in running order.
  • Add the standard attendant’s mass if you carry an attendant.
  • Do not add this amount for every passenger.
  • Include suitcases in laden mass.

Exam trap: Wrong: mass in running order is an actual weighing. Right: you calculate it using standard masses.

Read the full explanation
  • Tare is the mass of the bus with its authorised fixed equipment and the necessary supplies of water, fuel, lubricants, spare parts, tools and accessories; it does not include service staff, passengers or load. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • To obtain the mass in running order, you must add the standard driver mass of 75 kg to the tare and, for buses and coaches, another 75 kg for the attendant if one is carried. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • Laden mass is the actual mass of the vehicle during that journey, including its load, service staff and passengers. You must therefore also count suitcases: a minibus with every seat occupied can have a different mass depending on the luggage it carries. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • If your minibus has a tare of 4,000 kg, its mass in running order is 4,075 kg with the standard driver and no attendant, or 4,150 kg with both. This example calculates the conventional mass in running order; weighing the vehicle for the journey determines its laden mass. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

2Authorised maximums and technical maximums

A green minibus carrying passengers stands on a weighbridge while an inspector holds its documentation beside the scale indicator.
The key idea

Respect authorised, technical, axle and combination limits together.

LimitWhat you must check
MMAMaximum authorised mass when laden
Technical maximumCapacity specified by the manufacturer

Remember

  • Check your minibus’s MMA; there is no single MMA for every minibus.
  • Respect the authorised passenger capacity too.
  • For each axle, add the load on all its wheels.
  • Check the combination even if the minibus and trailer each meet their limits.

Exam trap: Wrong: a higher technical capacity increases your MMA. Right: you meet both limits and all other applicable limits.

Read the full explanation
  • MMA (maximum authorised mass) is the maximum mass you can use with the laden vehicle on public roads. The technically permissible maximum mass is based on its construction and is specified by the manufacturer; you must not confuse technical capacity with authorisation to drive on the road. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • You must comply simultaneously with the applicable regulatory limits, the MMA assigned to your minibus, its technical limits and its axle limits. If your vehicle is authorised for 5,500 kg, you must use that figure; a higher technical capacity or a higher figure in another row of the table does not in itself change your documentation. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • Axle mass is the mass transmitted to the ground by all the wheels attached to that axle. You must add both sides and, if there are twin wheels, all of them: you cannot apply the axle limit separately to each tyre. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For a vehicle combination, you must also distinguish between the maximum authorised mass of the combination, its technical maximum mass and the towable mass. Keeping the bus and trailer individually within their limits is not enough if the combination exceeds its applicable maximum. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • D1 does not set a single MMA for all minibuses: you must check the MMA of each vehicle and also respect its authorised passenger capacity, even if its mass still allows you to carry more people. [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4). [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

3Maximum bus width

Two technicians use a tape to measure the body width of a green minibus stopped beside the right-hand kerb in a layby on a Spanish road.
The key idea

Check the authorised width and the actual space available.

2.55 mGeneral maximum width
2.60 mBus adapted for prisoners
Type of busMaximum width
General, including a minibus2.55 m
Specially adapted to carry prisoners2.60 m

Remember

  • Fewer seats do not give you a different general width.
  • For the exception, the bus needs central cells and a central aisle.
  • The cells must be separate from the driving or escort areas.
  • Check projections and the actual space before entering a narrow passage.

Exam trap: Wrong: carrying prisoners occasionally allows 2.60 m. Right: the bus needs the specific adaptation described.

Read the full explanation
  • The general maximum authorised width is 2.55 m, including for your D1 minibus. Your vehicle's actual width may be less than this maximum. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The specific exception for buses specially equipped to transport prisoners allows 2.60 m. This requires a central cell compartment, separate from the front driving and escort area and the rear escort area, and a central aisle; occasionally transporting prisoners does not meet these requirements. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • You must use the dimensions determined under the type-approval regulations applicable to the vehicle category. To plan a narrow route, you also need to know the physical space occupied by the bodywork and its projections; compliance with the regulatory width does not guarantee that you can pass an oncoming vehicle at every narrow passage. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

4Height and overhead obstacles

A green minibus with rooftop equipment is stopped beside the right-hand kerb before a low stone bridge.
The key idea

Measure the full height and check overhead obstacles along your route.

4.00 mGeneral height with load
4.20 mClass I buses only
Bus classMaximum height with load
A or B4.00 m
I4.20 m

Remember

  • Include equipment and the load when checking height.
  • If your minibus is class A or B, use the general maximum.
  • An urban service does not change its class.
  • Respect lower height limits along your route.

Exam trap: Wrong: you apply 4.20 m to your urban class A minibus. Right: its general maximum is 4 m.

Read the full explanation
  • The general maximum height, including the load, is 4.00 m. You must check the complete vehicle in its configuration for road use: you cannot consider only the height of the passenger compartment and overlook equipment or carried items that determine its highest point. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The 4.20 m height exception expressly applies to Class I buses. For your Class A or B minibus, you must use the general maximum of 4 m; operating an urban service does not make it Class I or allow you to apply that height exception. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [UN Regulation 107, paragraphs 2.1.1 and 2.1.2](https://www.boe.es/doue/2018/052/L00001-00137.pdf).
  • You must check the clearance along the route as well as the regulatory maximum height. The load must not obstruct passage beneath bridges, viaducts or overhead installations; keeping your minibus within 4 m does not allow you to ignore a lower limit along the route. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

5Length of rigid buses, articulated buses and combinations

A compact green two-axle minibus travels to the right in the nearest lane of a two-way road in a Mediterranean landscape.
The key idea

With D1, check your minibus’s length and the combination’s technical compatibility.

8 mD1 motor vehicle
16Passengers besides you
Vehicle: general table, not D1 entitlementMaximum length
Rigid bus with two axles13.50 m
Rigid bus with more than two axles15 m
Articulated bus18.75 m
Bus with trailer, including trailer18.75 m

Remember

  • With D1, your vehicle is designed for up to 16 passengers besides you.
  • See the ages and CAP details in “Passenger transport driving licences and categories”.
  • Do not use general lengths as your D1 limits.
  • Check the combination’s technical compatibility.

Exam trap: Wrong: general tables let you drive a long bus with D1. Right: your motor vehicle must not exceed 8 m.

Read the full explanation
  • With D1, you can drive a motor vehicle designed and built for up to 16 passengers in addition to you and with a maximum length of 8 m. An 8.20 m bus falls outside D1 even if it carries only 10 passengers. [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • Check the minimum ages and how they relate to CAP in «Passenger transport driving licences and categories», section «General minimum ages and D1 with CAP».
  • The general vehicle table allows 13.50 m for two-axle rigid buses and 15 m for rigid buses with more than two axles. You must know these figures to identify the categories in exam questions, but you must not use them as the length authorised by your D1: your licence entitlement remains limited to 8 m. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • The general maximum length is 18.75 m for both articulated buses and buses with a trailer, including the trailer. For a D1 combination, the licence length limit applies to the motor vehicle; the general dimensional limit for the combination remains subject to its technical compatibility. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).

6Ski racks and removable accessories

Two people use a tape to measure the total length of a green minibus parked beside the kerb, including the orange ski carrier attached to the rear.
The key idea

Count removable accessories within your bus’s maximum length.

Remember

  • Include the ski rack when checking length.
  • Being removable gives an accessory no extra length allowance.
  • Projecting-load allowances do not remove maximum dimensions.
  • Keep compulsory lights, signals, plates and markings visible.

Exam trap: Wrong: V-20 replaces hidden lights. Right: you reposition the assembly or use a regulation-compliant solution that keeps them visible.

Read the full explanation
  • You must include removable accessories, such as a ski rack, within the maximum length applicable to the bus. You calculate the measurement in the configuration you use on the road, even if you remove the accessory at the end of the journey. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • If the bodywork and removable accessory together increase the length of your minibus, you must check the resulting length and its compatibility with D1. Checking your driving entitlement and checking the regulatory maximum for the bodywork are separate requirements. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • You must distinguish the accessory rule from the rules allowing a load to project. The percentage allowance in article 15 of the RGC does not remove the maximum length for the vehicle and its load or the express requirement to include the bus's accessories. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [RGC, arts. 13 and 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • Before setting off, you must also check that the accessory and luggage do not obscure mandatory lights, signalling devices, plates or identification markings. A V-20 does not replace obscured lights: you must reposition the assembly or provide a solution that complies with the regulations and keeps the required devices visible. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).

7MMA (maximum authorised mass) of two-axle buses

A person removes a suitcase from a green minibus parked beside the right-hand kerb, with empty seats visible and two other suitcases on the pavement.
The key idea

Check your vehicle’s class and documents before choosing its MMA.

20 tTwo axles: class I
19.50 tTwo axles: classes II/III
Two-axle busMMA reference
Class I20 t
Classes II and III19.50 t
Classes A and BCheck documents; no separately named table row

Remember

  • Check your minibus’s approved class.
  • Class A allows standing passengers by design; class B does not.
  • Driving in a city does not make your minibus class I.
  • For classes A or B, check documented authorised and technical limits.
  • Reduce your load if you exceed MMA, even with empty seats.

Exam trap: Wrong: you apply 18 t to every two-axle vehicle. Right: that row excludes buses; do not invent equivalents for A or B.

Read the full explanation
  • UN Regulation 107 distinguishes classes I, II and III for vehicles with capacity for more than 22 passengers in addition to the driver; for capacity not exceeding 22, it distinguishes A and B. Your minibus for up to 16 passengers falls within the lower-capacity group in this classification. [UN Regulation 107, paragraphs 2.1.1 and 2.1.2](https://www.boe.es/doue/2018/052/L00001-00137.pdf). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • Class A is designed to carry standing passengers and class B is not. You must use the class corresponding to the type approval, rather than infer class I from driving in a city or class III from having everyone seated; you study the specific conditions in «Transporting passengers and minors», under «When you can carry standing passengers». [UN Regulation 107, paragraphs 2.1.1 and 2.1.2](https://www.boe.es/doue/2018/052/L00001-00137.pdf).
  • In table 2 of Annex IX, the maximum for a class I two-axle bus is 20 t, and for classes II and III it is 19.50 t. These figures apply to the classes specified in the table. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The 18 t row for two-axle motor vehicles expressly excludes buses, and the table has no separate row specifically for class A or B two-axle buses. For your particular vehicle, you must check the authorised MMA and the documented technical limits, without inventing an equivalence between classes. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For example, if your minibus has an MMA of 5,500 kg and an actual mass of 5,600 kg, you must reduce the load even if you have spare seats. You must count passengers and luggage, respect the authorised capacity and check each axle: the higher figures for other buses do not offset your excess mass. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

8Three and four axles: vehicle masses

A green two-axle minibus stands on a vehicle weighbridge beside a road in a Mediterranean landscape.
The key idea

Choose the mass limit using the axles, vehicle layout and required conditions.

25 tThree axles: general rule
26 tThree axles: conditions apply
28 tThree-axle articulated bus
32 tFour axles: conditions apply
Vehicle layoutMaximumConditions
Three-axle motor vehicle25 tGeneral rule
Three-axle motor vehicle26 tDriving axle: twin tyres and air suspension or recognised equivalent; or the stated alternative
Three-axle articulated bus28 tSpecific general limit
Four-axle rigid vehicle with two steering axles32 tDriving axle: twin tyres and air suspension or recognised equivalent; or the stated alternative
Other four-axle rigid vehicles31 tGeneral rule

Remember

  • For these increases, check twin tyres and air suspension or a recognised equivalent.
  • Alternatively, each driving axle needs twin tyres and a maximum mass of 9.5 t.
  • Always respect lower technical and authorised limits.
  • These tables do not extend your D1 passenger capacity or length limit.
  • With a D1 towing vehicle, trailer MMA above 750 kg requires D1+E.

Exam trap: Wrong: any three-axle rigid vehicle allows 28 t. Right: that figure applies to a three-axle articulated bus.

Read the full explanation
  • With D1, you can add a trailer with an MMA of up to 750 kg; if it exceeds that MMA, you need D1+E for a D1 towing vehicle. The following configurations do not extend your licence's capacity and length limits. [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • The general row for three-axle motor vehicles sets a limit of 25 t. You can reach 26 t when the driving axle has twin tyres and air suspension or a recognised equivalent, or when each driving axle has twin tyres and the maximum mass on each axle does not exceed 9.5 t. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For a three-axle articulated bus, the specific general limit is 28 t. This figure applies to that particular configuration. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For four-axle rigid vehicles with two steering axles, the table allows 32 t subject to the conditions of twin tyres and air suspension or an equivalent on the driving axle, or twin tyres on each driving axle and a maximum of 9.5 t on each. For other four-axle rigid vehicles, the general figure is 31 t. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • You must treat these masses as ceilings for the configuration, subject to the technical and authorised limits of the particular vehicle. You check length and mass separately: the fact that a rigid vehicle with more than two axles can measure 15 m does not automatically give you the mass allowance of another configuration. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). For your D1 licence, these rows help you interpret bus configurations. [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).

9Propulsion technologies and mass increases

An electric minibus with its battery compartment open stands on a weighing platform while an inspector checks a document beside the scale.
The key idea

Apply technology increases only when the note and its conditions allow them.

1 tMaximum: alternative fuel
2 tMaximum: zero emissions
1 tExtra: qualifying urban service
Technology: only cases covered by the noteMaximum increase for extra mass required
Alternative fuel1 t
Zero emissions2 t

Remember

  • Check that the note applies to your chosen row.
  • The technology increase depends on the extra mass required.
  • Respect the technical maximum and axle maximums.
  • Do not add increases if the question excludes them.

Exam trap: Wrong: you add every increase to any bus. Right: you check the row, technology, extra mass required and technical limits.

Read the full explanation
  • Note 1 to the table allows an increase in the MMA of the vehicles or combinations it covers by the additional mass required for alternative-fuel technology, up to 1 t, or zero-emission technology, up to 2 t. You must link the increase to that technology and the case covered by the regulations. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For vehicles intended for services in urban environments, the note provides for up to 1 t in addition to the stated technology-related increases. You must always respect the technically permissible maximum mass and the maximum axle masses: the exception does not remove these checks. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • To apply an increase, you must check which row the note applies to, the particular propulsion system and the additional mass required; the rows for class I, II and III two-axle buses do not show the reference (1). For a minibus, you must always start from its authorisation and technical characteristics. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • If the question expressly excludes special propulsion-related increases, you must answer with the general limit for the configuration. For example, for a three-axle articulated bus under those conditions, the reference figure is 28 t, without adding amounts on your own initiative. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

10Single axles: driving and non-driving

A green minibus is stationary on two weighing platforms, with a cutaway showing the engine connected to the rear axle and the front axle without a propulsion connection.
The key idea

Identify driving axles and respect your vehicle’s MMA too.

10 tSingle non-driving axle
12 tGeneral single driving axle
13 tDriving: class I bus
12.6 tDriving: classes II/III
Single axle and vehicleGeneral table maximum
Non-driving10 t
General driving axle, including class A or B minibus12 t
Class I bus driving axle13 t
Class II or III bus driving axle12.6 t

Remember

  • Identify a driving axle by whether it receives driving power.
  • Do not identify it just by its front or rear position.
  • Respect lower authorised and technical limits.
  • Correct axle overload even when you meet the overall MMA.
  • Respect the loads your tyres can carry too.

Exam trap: Wrong: an axle limit increases your MMA. Right: you meet the vehicle limit and each axle limit together.

Read the full explanation
  • The table's maximum for a single non-driving axle is 10 t. For a general single driving axle, it is 12 t; the latter is the general reference for a class A or B minibus, subject to any lower authorised or technical limit. The distinction depends on whether the axle receives driving force, rather than whether it is at the front or rear. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • On class I urban buses, the single driving axle can carry up to 13 t. On class II and III interurban buses, the maximum for the single driving axle is 12.6 t: you must choose this figure when the exam identifies that class. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • If your minibus has an MMA of 5,500 kg, the general reference of 12 t for a driving axle does not allow you to load the vehicle to that figure: you must comply with the maximum limits for both the vehicle and its axles at the same time. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • With a total mass of 5,200 kg and 3,300 kg actually borne by an axle authorised for 3,200 kg, you must correct the load distribution even though the total is below an MMA of 5,500 kg. You must also keep within the loads the tyres can carry according to their load indices and the regulatory conditions. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

11Motor vehicle tandem axle group

A green minibus travels to the right in its lane, with its two closely spaced rear axles visually grouped by an orange section of the bodywork.
The key idea

Check axle spacing to find the limit for the whole group.

12 tMotor tandem: smallest spacing
16 tMotor tandem: middle spacing
18 tMotor tandem: largest interval
19 tLargest interval: conditions apply
Spacing: motor vehicle tandemMaximum for whole group
Less than 1.00 m12 t
From 1.00 m to less than 1.30 m16 t
From 1.30 m to less than 1.80 m18 t; 19 t with twin tyres and air suspension or recognised equivalent on the driving axle, or the stated alternative

Remember

  • Measure the distance between the axles.
  • Apply the limit to the whole group, not each axle.
  • For 19 t, check the special tyre and suspension conditions.
  • Alternatively, each driving axle needs twin tyres and a maximum mass of 9.5 t.

Exam trap: Wrong: exactly 1.30 m belongs in the previous interval. Right: it enters the 18 t interval, or 19 t with conditions.

Read the full explanation
  • To interpret a tandem axle group, you must look at the spacing d between the two axles. On a motor vehicle, the maximum for the group is 12 t if d is less than 1.00 m and 16 t if d is at least 1.00 m but less than 1.30 m. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • If the spacing is at least 1.30 m but less than 1.80 m, the ordinary limit for the motor vehicle's tandem axle group is 18 t. You must pay attention to the boundaries: exactly 1.30 m falls within this range, rather than the previous one. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • In that last range, you can apply 19 t when the driving axle has twin tyres and air suspension or a recognised equivalent, or when each driving axle has twin tyres and its maximum mass does not exceed 9.5 t. You can only apply this maximum if those conditions are met. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The tandem figure limits the whole group, rather than each axle separately. If a group has a permitted maximum of 18 t, you cannot interpret this as allowing 18 t on each of its two axles; you must check the distribution, the applicable limits and the total for the bus together. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

12Trailer axle groups

A green minibus travels to the right along a rural road, towing a small orange single-axle trailer.
The key idea

Distinguish axle-group limits from the limit for the whole trailer.

11 tTandem: smallest spacing
20 tTandem: largest spacing
21 tTriaxial: smaller interval
27 tTriaxial: larger interval
Trailer or semi-trailer groupAxle spacingMaximum for whole group
TandemLess than 1.00 m11 t
TandemFrom 1.00 m to less than 1.30 m16 t
TandemFrom 1.30 m to less than 1.80 m18 t
TandemAt least 1.80 m20 t
TriaxialUp to and including 1.30 m21 t
TriaxialAbove 1.30 m, up to and including 1.40 m27 t

Remember

  • Do not use the smallest motor vehicle tandem figure for your trailer.
  • Check the maximum for the whole trailer too.

Exam trap: Wrong: a 27 t triaxial group allows a 27 t trailer. Right: the whole three-axle trailer has a general maximum of 24 t.

Read the full explanation
  • For a trailer or semi-trailer tandem axle group, the maximum limits are 11 t if d is less than 1.00 m; 16 t from 1.00 m inclusive to 1.30 m exclusive; and 18 t from 1.30 m inclusive to 1.80 m exclusive. The first figure differs from that for a motor vehicle. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • With spacing of at least 1.80 m, the trailer or semi-trailer tandem axle group has a maximum of 20 t. [RGV, Annex IX, table 1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For a trailer or semi-trailer triaxle group, the maximum is 21 t if the distance between axles is no more than 1.30 m. If it exceeds 1.30 m and is no more than 1.40 m, the maximum is 27 t; exactly 1.30 m falls within the first case. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The vehicle table sets 18 t for two-axle trailers and 24 t for three-axle trailers. The fact that a triaxle group can carry 27 t does not in itself authorise a complete trailer of 27 t. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). The maximum limits for heavy trailers help you interpret the general table; you find the scope of D1 in the section «Three and four axles: vehicle masses». [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).

13Mass distribution and load on driving axles

A minibus with seated passengers and suitcases in a low luggage compartment is stopped beside the kerb with its wheels on weighing platforms, and the rear axle platform is highlighted in green.
The key idea

Distribute loads without overloading axles or removing weight from the driving axles.

25 %General minimum driving-axle load
3.00 mMinimum axle gap between vehicles

Remember

  • Keep at least 25 % of the laden mass on the driving axles.
  • For a combination, use its total laden mass.
  • For road trains, measure between the towing vehicle’s rear axle and foremost trailer axle.
  • Keep at least 3.00 m between those axles.
  • If an axle is overloaded, reduce or redistribute the load and check again.

Exam trap: Wrong: meeting the total mass limit guarantees each axle complies. Right: you also check distribution and minimum driving-axle load.

Read the full explanation
  • You must check the weight on the driving axle or axles: as a general rule, it must not be less than 25 % of the total laden mass of the vehicle or combination. For a minibus with an actual mass of 5,200 kg, this requires at least 1,300 kg on the driving axles; this is a minimum load requirement, which you must meet without exceeding the maximums. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • In a road train, the distance between the rear axle of the towing vehicle and the front axle of the trailer must not be less than 3.00 m. You must distinguish this distance between vehicles from the spacings d used to classify tandem axles within the same group. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • When preparing your journey, you must consider where you place passengers and luggage, because complying with the total mass limit does not guarantee compliance with each axle limit. If weighing reveals an overloaded axle, you must safely reduce or redistribute the load and check the limits again before driving. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

14Combination masses and the scope of D1

A green minibus with a small orange trailer is stationary with all its wheels on a weighbridge beside a road.
The key idea

Check your combination’s limits without copying exceptions for other transport.

36 tTowing: two; trailer: two axles
42 tTowing: two; trailer: three axles
44 tTowing: three; trailer: two/three axles
Road train: towing vehicle axlesTrailer axlesGeneral maximum
TwoTwo36 t
TwoThree42 t
ThreeTwo or three44 t

Remember

  • Check your combination’s authorised mass and your minibus’s towable mass.
  • Respect the trailer MMA allowed by your licence too.
  • Apply any lower technical or authorised limit.
  • Do not use exceptions for other transport to increase your authorised mass.

Exam trap: Wrong: exceptions for other transport increase your limit. Right: you respect the limits applying to your particular combination.

Read the full explanation
  • For a D1 minibus with a trailer, you must apply the authorised mass of the combination and the vehicle's towable mass, as well as the trailer MMA (maximum authorised mass) limit for your licence stated in the section “Three and four axles: vehicle masses”. [RGV, Annex IX, section 4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The general table for road trains sets 36 t for a two-axle towing vehicle and a two-axle trailer; 42 t for a two-axle towing vehicle and a three-axle trailer; and 44 t for a three-axle towing vehicle and a two- or three-axle trailer. You must comply with any lower technical and authorised limits for your combination. [RGV, Annex IX, table 2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The rows for tractor units with semi-trailers, the increases for intermodal transport and the exceptions for round timber or Euro-modular configurations govern other transport situations. You cannot use them to increase your minibus's authorised mass. [RGV, Annex IX, tables 2 and 3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

15Towable mass and coupling load

A green minibus travels in the right-hand lane towing an orange single-axle trailer loaded with boxes and connected to the rear coupling by a visible drawbar.
The key idea

Check how much you may tow and how much weight the coupling can carry.

10 %Relative vertical load limit
1,000 kgAbsolute vertical load limit
750 kgMaximum D1 trailer MMA
3,500 kgOrdinary ceiling: stated braking
Trailer brakingTowable mass limit; also respect technical and combination limits
UnbrakedHalf the towing vehicle’s tare increased by 75 kg; maximum 750 kg
Overrun braking onlyTowing vehicle’s MMA; maximum 3,500 kg
Continuous braking, category M towing vehicleSame rule as overrun braking only

Remember

  • Check coupling strength and technically permissible towable mass.
  • Count vertical coupling load towards the towing vehicle and its rear axles.
  • With an evenly loaded centre-axle trailer, use the lower vertical load limit.
  • Respect the vehicle’s and coupling’s technical limits too.

Exam trap: Wrong: better brakes allow any trailer with D1. Right: with D1, trailer MMA remains limited to 750 kg.

Read the full explanation
  • You must check the technically permissible towable mass and the strength of the coupling before forming a combination. The maximum mass of the towing vehicle and trailer combination is expressed as the towing vehicle's MMA plus its MMR (maximum towable mass), but is limited by the combination's technical maximum and legally permissible maximum. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • With a centre-axle trailer, part of the weight is transferred vertically to the coupling. This load counts towards the mass of the towing minibus and its rear axles; you must not calculate the distribution as though the trailer's entire weight rests solely on its wheels. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The maximum authorised vertical load on the coupling, with the centre-axle trailer's load evenly distributed, does not exceed the lower of 10 % of the trailer's maximum mass and 1,000 kg. You must also comply with the technical limits of the vehicle and the coupling itself. [RGV, Annex IX, section 4.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). For example, with a trailer whose maximum mass is 750 kg, 10 % is 75 kg; you must comply with a lower technical limit if one applies. [RGV, Annex IX, section 4.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For an unbraked trailer, Annex IX limits the towable mass to half the towing vehicle's tare plus 75 kg, with a ceiling of 750 kg, and also to what is technically permissible. With overrun braking only, the normal limit is the towing vehicle's MMA and, in all cases, 3,500 kg; for category M vehicles with continuous braking, it refers to that same rule. The braking system does not extend your licence entitlement. [RGV, Annex IX, sections 4.1.1 and 4.1.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).

16Bus turning circle and swept path

A green minibus viewed from above remains entirely between the two concentric circular boundaries of a turning test area.
The key idea

Distinguish turning radii from the different swept-path tests.

12.50 mOuter radius
5.30 mInner radius
0.60 mProjection: entry test
Bus testMaximum projection beyond outer plane
Entry from a straight line0.60 m
Following the circle: rigid M2 or M30.8 m
Following the circle: articulated M2 or M31.2 m

Remember

  • You must complete the turn both ways within the circles.
  • The circle measurements are radii, not diameters.
  • When entering from straight ahead, check projection beyond the marked outer plane.
  • For articulated buses, start with the rigid sections aligned with that plane.
  • Watch how far the vehicle’s ends swing out.

Exam trap: Wrong: you use circle-following limits for the entry test. Right: you distinguish the tests and apply 0.60 m to entry.

Read the full explanation
  • Every motor vehicle and combination must be able to follow a complete 360-degree circular path in both directions within two concentric circles with an outer radius of 12.50 m and an inner radius of 5.30 m. No outer extremity may project beyond these circles. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • Turning-circle measurements are expressed as radii. The corresponding outer diameter is 25 m and the inner diameter is 10.60 m; the gap between the two radii is 7.20 m, but this difference is not a lane width that permits any real manoeuvre. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • Under the specific requirement for a bus entering this circular area from a straight line, no part must extend more than 0.60 m beyond the vertical plane tangent to its outer side, marked with the vehicle stationary. If it is articulated, you must consider its rigid sections initially aligned with that plane. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • When following the circle with a radius of 12.5 m, the Annex also sets limits for projection beyond the plane of 0.8 m for rigid M2 or M3 vehicles and 1.2 m for articulated M2 or M3 vehicles, including with lift axles raised. This test measures the swept path while following the circle, whereas the previous test measures entry from a straight line. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

17How far the load may project

A green minibus travels in the right-hand lane with a beam secured to its roof rack projecting slightly beyond the rear, with its end protected and marked by a red-and-white striped panel.
The key idea

On your bus, loads may project only behind, within the applicable limits.

10 %General rear projection
15 %Indivisible load rear projection
Load on a busMaximum rear projection as percentage of vehicle length
General10 %
Indivisible15 %

Remember

  • Then check the overall regulatory dimensions.
  • The percentage does not remove the rule for removable accessories.
  • Do not use front or side allowances reserved for goods-only vehicles.
  • Protect the projecting end to prevent harm.
  • Luggage is not indivisible just because you prefer keeping it together.

Exam trap: Wrong: 15 % lets you exceed regulatory dimensions. Right: you respect both the percentage and overall maximums.

Read the full explanation
  • As a general rule, the load must remain within the vehicle's outline when viewed from above. On vehicles not intended exclusively for goods, such as buses, it may project to the rear by up to 10 % of the vehicle's length, or up to 15 % if the load is indivisible. [RGC, arts. 13 and 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • For an 8 m minibus, the percentage calculation gives 0.80 m for an ordinary load and 1.20 m if it is indivisible. The projection is calculated using the vehicle's length; you must then check the overall dimensions permitted by the regulations: the percentage does not remove the maximums in Article 13 or the express rule on removable accessories. [RGC, arts. 13 and 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • You cannot apply to a bus the permission for front and side projections that the Article reserves for vehicles intended exclusively for goods. On those vehicles, certain indivisible loads may project 2 m to the front and 3 m to the rear if the vehicle is over 5 m long; this is not an allowance for your minibus. [RGC, arts. 13 and 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • You must protect the projecting end and take precautions to prevent harm to other road users. An indivisible load is not simply luggage that you prefer to keep together: under special transport rules, it relates to a load that cannot be divided without unnecessary cost or risk of damage and cannot be carried on a vehicle complying with the ordinary maximums. [RGC, arts. 13 and 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15). [RGV, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a14).

18Marking projecting loads

A minibus travels in daylight in the right lane with a secured load of beams on its roof projecting beyond the rear and a V-20 panel at its rearmost end.
The key idea

Mark projecting loads even when you drive by day.

0.40 mSide threshold from position lights
Projecting loadMarking you must use
RearV-20; add a red light at night or in significantly reduced visibility
Rear, across the full widthPanels at both transverse ends, with stripes forming an upside-down V
Legally permitted side load, over 0.40 m beyond the position lights’ outer edgeAt night or in reduced visibility: white light and reflector forwards, red ones rearwards

Remember

  • Place V-20 at the rear end, perpendicular to the vehicle’s length.
  • For a load projecting across the full rear width, fit panels at both ends.
  • Their stripes must form an upside-down V.
  • At night or in significantly reduced visibility, add a red light behind.
  • A white front light does not allow front projection on your bus.

Exam trap: Wrong: marking allows you to widen your bus. Right: side-marking duties apply only to legally permitted side loads.

Read the full explanation
  • You must mark a load projecting to the rear with the V-20 panel, placed at its rear end and kept perpendicular to the vehicle's longitudinal axis at all times. The panel is also compulsory in daylight with good visibility. [RGC, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • If the load projects lengthways across the full width of the rear, you must fit two panels, one at each transverse end of the load or projecting material. Their stripes must form an inverted V. [RGC, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • Between sunset and sunrise, or in conditions that significantly reduce visibility, you must add a red light to the rear-projecting load. Where a load is authorised to project to the front, the corresponding light is white; this provision does not authorise front projections on a bus. [RGC, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • If a legally permitted side-projecting load extends more than 0.40 m beyond the outer edge of the position lights, you must apply the side-marking requirements for night-time or reduced visibility: a white light and reflector facing forwards and a red light and reflector facing rearwards. This is a marking obligation, not general permission to increase the vehicle's width. [RGC, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).

19Total mass and axle mass signs

A minibus carrying passengers and luggage stands still with its rear axle wheels on a weighing platform while an operator checks a device beside the kerb.
The key idea

Compare mass signs with your actual weight and its distribution.

SignWhat you compare
R-201Actual laden mass of the vehicle
R-202Actual mass transmitted by any axle

Remember

  • Include people and luggage when checking actual mass.
  • For each axle, count all its wheels.
  • Do not calculate axle loads by dividing total weight by the axle count.
  • Matching the figure does not exceed it; check other restrictions too.

Exam trap: Wrong: you compare R-201 with MMA. Right: you compare actual journey mass; R-202 requires you to check each axle.

Read the full explanation
  • The R-201 mass restriction sign prohibits you from passing if the laden mass exceeds the number of tonnes shown. You must compare the actual weight of the bus on that journey, including people and luggage, rather than its MMA (maximum authorised mass) or just the mass of the suitcases. [Official catalogue, R-201 and R-202, RD 465/2025](https://www.boe.es/boe/dias/2025/06/17/pdfs/BOE-A-2025-12199.pdf).
  • If your minibus has an MMA of 5.50 t but actually weighs 4.80 t, an R-201 sign showing 5 t does not prohibit you from passing on the basis of that mass. If it weighs 5.20 t, it does prohibit you from passing; you must also check the other road restrictions and the vehicle’s own limits. [Official catalogue, R-201, RD 465/2025](https://www.boe.es/boe/dias/2025/06/17/pdfs/BOE-A-2025-12199.pdf).
  • The R-202 axle mass restriction sign requires you to check the mass transmitted by any axle through all its wheels. You cannot divide the total mass by the number of axles and assume that they all carry the same load: you must know the actual distribution. [Official catalogue, R-201 and R-202, RD 465/2025](https://www.boe.es/boe/dias/2025/06/17/pdfs/BOE-A-2025-12199.pdf).
  • At an R-202 sign showing 3 t, you cannot pass in a minibus with 3.20 t on one axle, even if the other axles carry less and the total complies with its MMA. For both signs, you must pay attention to the word exceeds: equalling the figure does not in itself constitute the excess that defines the prohibition. [Official catalogue, R-201 and R-202, RD 465/2025](https://www.boe.es/boe/dias/2025/06/17/pdfs/BOE-A-2025-12199.pdf).

20Length, width and height signs

A green minibus is stopped before a stone bridge whose arch is lower than the roof of the vehicle.
The key idea

Compare your actual dimensions, including loads, with signs along your route.

SignMaximum dimension to check, including load
R-203Vehicle or combination length
R-204Vehicle width
R-205Vehicle height

Remember

  • Include the trailer and relevant accessories.
  • Check restrictions before reaching a passage with no way out.
  • Check your vehicle’s dimensions and its equipment.
  • Meeting the general maximum does not let you exceed a sign’s limit.

Exam trap: Wrong: driving empty lets you ignore a length restriction. Right: you compare the full actual length with the sign.

Read the full explanation
  • The R-203 length restriction sign prevents you from passing in a vehicle or combination whose maximum length, including its load, exceeds the length shown. You must include the trailer and any relevant accessories: you cannot pass a 7 m restriction in your 8 m minibus simply because it is empty. [Official catalogue, R-203, RD 465/2025](https://www.boe.es/boe/dias/2025/06/17/pdfs/BOE-A-2025-12199.pdf).
  • The R-204 width restriction sign compares the figure shown with the maximum width of the vehicle, including its load. You cannot enter a passage restricted to 2.50 m in a bus that is 2.55 m wide; complying with the general statutory width limit does not exempt you from the specific limit. [Official catalogue, R-203 to R-205, RD 465/2025](https://www.boe.es/boe/dias/2025/06/17/pdfs/BOE-A-2025-12199.pdf).
  • The R-205 height restriction sign prohibits you from passing if the maximum height of the vehicle and its load exceeds the height shown. If your minibus is 3.10 m high, you cannot go through a passage restricted to 3 m, even though you are below the general maximum of 4 m. [Official catalogue, R-205, RD 465/2025](https://www.boe.es/boe/dias/2025/06/17/pdfs/BOE-A-2025-12199.pdf).
  • Before reaching a point where you cannot continue, you must compare the actual dimensions of the configuration you are driving with the restrictions on your route. Consult the specifications for your vehicle and its equipment. [Official catalogue, R-203 to R-205, RD 465/2025](https://www.boe.es/boe/dias/2025/06/17/pdfs/BOE-A-2025-12199.pdf).

21Safe loading within the limits

A person checks the straps securing several suitcases distributed in the open luggage compartment of a minibus parked beside the pavement.
The key idea

Distribute and secure luggage to keep your bus stable.

Remember

  • Prevent luggage dragging, falling or moving dangerously.
  • Secure it when necessary.
  • Avoid preventable noise, dust and other disturbance.
  • Fully and effectively cover materials that produce dust or could fall.
  • Check mass and distribution even when all bags fit in the hold.

Exam trap: Wrong: covering the load guarantees it is secure. Right: you also check that it cannot move dangerously.

Read the full explanation
  • You must distribute and, where necessary, secure luggage and its accessories so that they do not drag, fall or move dangerously. The arrangement of the luggage must also maintain the stability of the bus. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • You must prevent the load from causing noise, dust or other avoidable nuisance. When you carry materials that produce dust or may fall, you must keep them completely and effectively covered; you must not confuse a cover with a system that, by itself, ensures the load is secured. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • When checking before departure, you must consider the volume of the items of luggage together with their mass and distribution. Luggage that fits in the hold can still cause excessive total mass or excessive loading on an axle; loading arrangements are covered in «Transporting passengers and minors», in the sections «Luggage in the hold and passenger compartment» and «Clear aisles and luggage conditions». [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).

22Authorisations to exceed the limits

An officer checks the document shown by the driver of a minibus stopped beside its right-hand kerb.
The key idea

You need prior authorisation when special transport exceeds regulatory limits.

Remember

  • Do not set off expecting to get authorisation during the journey.
  • Authorisation depends on technical characteristics or an indivisible load.
  • You need a binding road-authority report and the relevant transport checks.
  • Respect the conditions and authorised period or number of journeys.
  • On urban roads, follow the route set by the municipal authority.
  • Check that no route obstacles or restrictions prevent your journey.

Exam trap: Wrong: authorisation permanently increases your MMA. Right: it is specific and conditional; it does not automatically allow more passengers or divisible luggage.

Read the full explanation
  • You cannot drive under ordinary rules if you exceed the statutory mass or dimension limits. The competent traffic authority may grant a special authorisation because of the vehicle’s technical characteristics or an indivisible load, subject to a binding report from the road authority and the relevant transport checks. [RGV, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a14).
  • The authorisation may limit the number of journeys or its period of use. Its conditions apply to the authorised vehicle and transport operation. [RGV, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a14).
  • For special transport involving an indivisible load, you need prior supplementary authorisation and must comply with its conditions, which take precedence over the applicable general rules as set out in Annex III. On urban roads, you must follow the route specified by the municipal authority. [RGV, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a14). [RGC, Annex III, group 1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).
  • As the authorisation holder, you must make sure that the route has no physical obstacles or restrictions that prevent the journey, including inspecting it beforehand where necessary. This check forms part of the common conditions for special transport and allows you to identify passages incompatible with the authorised dimensions. [RGC, Annex III, section 1.ª.7](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).

23Special transport on the road

A green minibus with an illuminated amber beacon is stopped in a gravel area outside the carriageway and shoulder while an orange car passes in its lane towards the right.
The key idea

Under special transport rules, follow your authorisation and route conditions.

50 mMinimum gap behind vehicle ahead
150 mMinimum visibility ahead and behind
5 mWider loads need traffic officers
72 hMinimum notice for traffic officers
Special transport with an indivisible load: caseCondition you must meet
Over 3 m wide or 20.55 m longEscort behind on motorways and dual carriageways, ahead on other roads; minimum 50 m
Group 1 on conventional roads below half the road’s generic speed limitAnother escort vehicle behind, at least 50 m away
Generic authorisationMaximum 70 km/h; group 1 may travel by day and night
Specific authorisationMaximum 60 km/h; group 1 may travel by day and night
Exceptional authorisationSpecified speed, maximum 60 km/h; group 1 needs express permission for night travel
Specific or exceptionalHolder notifies each journey the preceding day to departure-province traffic officers and designated road services, with place, date, time and authorisation copy
AllRespect lower roadworthiness-card restrictions and particular conditions

Remember

  • Under these rules, help others overtake and stop if necessary.
  • Stop and park off both the carriageway and hard shoulder.
  • Always use dipped beam and required signals, including V-2 when applicable.
  • Stop travelling and leave the road platform in dangerous weather or insufficient visibility.
  • Above 5 m wide, you need an escort by traffic officers.
  • The holder gives at least 72 hours’ notice and supplies the required details.

Exam trap: Wrong: these conditions apply to every bus. Right: they concern special transport; above 5 m wide, the holder gives the departure-province traffic officers and designated road body at least 72 hours’ notice, with journey details, registration numbers and an authorisation copy.

Read the full explanation
  • Under the Annex III rules, you must keep at least 50 m behind the vehicle ahead and make it easier for faster vehicles to overtake, stopping if necessary. You must stop and park off both the carriageway and the arcén (hard shoulder); these conditions are not the general rules for all buses. [RGC, Annex III, common conditions and group 1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).
  • You must keep dipped beam and the required warning signals in use at all times, including V-2 under the conditions in the annex. You must stop travelling and leave the road platform if weather conditions make driving dangerous or if you do not have at least 150 m of visibility ahead and behind. [RGC, Annex III, common conditions and group 1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).
  • For reasons of dimensions, you need an escort vehicle for special transport involving an indivisible load if it exceeds 3 m in width or 20.55 m in length. The escort vehicle must travel behind, at least 50 m away, on motorways and dual carriageways, and ahead on other roads; you must also comply with the specific conditions of your authorisation. [RGC, Annex III, common conditions and group 1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii). For reasons of speed, on conventional roads, if you travel at less than half the road’s generic speed limit, you also need another escort vehicle behind, at least 50 m away, for group 1 transport. [RGC, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).
  • With a general authorisation, your maximum speed is 70 km/h, and with a specific authorisation it is 60 km/h; with an exceptional authorisation, you must follow the speed specified, without exceeding 60 km/h, and comply with any lower restrictions on the tarjeta ITV (vehicle roadworthiness test card). These figures apply to special transport: speeds for ordinary services are covered in «Minibus speed and distances». [RGC, Annex III, common conditions and group 1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).
  • For group 1, a general or specific authorisation allows you to travel by day and by night; with an exceptional authorisation, travel between sunset and sunrise must be expressly permitted in it. As the authorisation holder, you must notify the officers in the province of departure and the services designated by the road authority of each journey under a specific or exceptional authorisation on the previous day, giving the place, date and time and sending a copy of the authorisation. [RGC, Annex III, group 1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).
  • If your width exceeds 5 m under these rules, you need an escort by officers. As the authorisation holder, you must give at least 72 hours’ notice to the officers in the province of departure and the body designated by the road authority, providing the journey details, registration numbers and a copy of the authorisation. [RGC, Annex III, section 1.ª.8](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).

24Minibus speed limiters

A driver drives a minibus in the right lane of a road, with a speedometer and a sealed speed limiter visible on the dashboard.
The key idea

Your limiter prevents speeds above its setting, but you must respect each road’s limits.

100 km/hM2/M3 limiter ceiling
Vehicle caseLimiter requirement
M2/M3 covered by the obligationMust prevent speeds above 100 km/h
Used only for urban public servicesExempt
Vehicles used by the Fuerzas Armadas (Armed Forces), law enforcement, civil protection, fire or other emergency servicesExempt
Unable by design to exceed the limitExempt
Scientific road testsExempt

Remember

  • Check category and registration to see whether your minibus needs a limiter.
  • Use an approved device installed and checked by an authorised workshop or organisation.
  • Keep the seals intact.
  • Have its operation checked after faults or broken or removed seals.
  • Keep the plate visible in your cab: workshop, date and selected speed.
  • Do not help tamper with the limiter: this is a very serious offence.

Exam trap: Wrong: some urban services exempt you from a limiter. Right: that exemption requires use only for urban public services; if required, the limiter setting still does not allow you to exceed lower limits.

Read the full explanation
  • RD 1417/2005 covers M2, M3, N2 and N3 vehicles with at least four wheels and a maximum design speed exceeding 25 km/h. You must check the category and registration to determine whether it applies. [RD 1417/2005, arts. 2 and 5](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a2).
  • In your M2/M3 minibus subject to this requirement, the limiter must prevent you from exceeding 100 km/h. [RD 1417/2005, art. 3](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a3).
  • Vehicles used by the Fuerzas Armadas (Armed Forces), Fuerzas y Cuerpos de Seguridad (law enforcement agencies), civil protection, the fire service or other emergency services are exempt; exemptions also apply to vehicles that cannot exceed the limit by design, vehicles used for scientific road tests and vehicles used only for urban public services. [RD 1417/2005, art. 7](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a7).
  • You must have a type-approved device, installed and checked by an authorised body or workshop, with its seals intact. If it breaks down or its seals are broken or removed, you must have its operation checked. [RD 1417/2005, arts. 6 and 8](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a8).
  • The installation plate, visible inside the cab, identifies the workshop, date and selected speed: «v = ... km/h». [RD 1417/2005, art. 15 and Annex, point 5](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990).
  • The limiter does not authorise you to drive at its set speed: you must comply with any lower applicable limit. See «Minibus speed and distances». [RGC, arts. 45 and 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48).
  • If you participate or assist in installing or activating components that alter the normal operation of the limiter, you commit a very serious offence. [Traffic Act, art. 77.m](https://www.boe.es/buscar/act.php?id=BOE-A-2015-11722#a77).

Check the bus before your journey

Apply all limits to the actual configuration you are going to drive.

  1. Identify your D1 minibus: designed for up to 16 passengers in addition to you, a maximum length of 8 m and, if you tow one, a trailer with an MMA (maximum authorised mass) no greater than 750 kg.
  2. Check the vehicle’s authorised and technical masses and dimensions and, where applicable, its towable mass.
  3. Include people, luggage and accessories; check the total mass and actual load distribution across axles or axle groups.
  4. Compare the resulting length, width and height with the regulatory limits and signs along your route.
  5. Correct any excess and check that the load is secured and the lights and plates are visible before driving.

Decide whether you can pass a restriction

Each sign requires you to compare a specific measurement.

  1. Identify R-201, R-202, R-203, R-204 or R-205 and read the figure and unit.
  2. For R-201, use the laden mass; for R-202, use the actual load on the most heavily loaded axle.
  3. For dimension signs, include the load, trailer and accessories as applicable.
  4. If you exceed the figure, find a suitable route; if you do not exceed it, check the other restrictions too.

Check a projecting load

The percentage and marking requirements must also comply with the overall limit.

  1. Check that the load can legally be carried on the vehicle and whether it is indivisible.
  2. For your minibus, calculate the maximum rear projection of 10 % or 15 % if the load is indivisible.
  3. Check the overall dimensions and the rule that includes removable accessories in the maximum length.
  4. Protect the end and fit a V-20 panel; use two panels forming an inverted V if the load occupies the full rear width.
  5. Add the red light at night or when visibility is significantly reduced, and check that no compulsory devices are obscured.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module