Theory · C1 Licence - Light Truck · Module 16 of 18

C1 lorry maintenance and checks

You learn to inspect your C1 lorry before setting off, check tyres, fluids, visibility, the coupling and brakes, and recognise warnings that require you to stop. You master what to do in a breakdown and the results and deadlines of the ITV (vehicle roadworthiness test), paying particular attention to differences between a goods lorry and a car that may appear in the exam.

40 min read28 sectionsReviewed Nov 3, 2026
A driver inspects a front tyre of a light goods truck parked on a depot forecourt beside a road.
Truck checks before setting off

1Check before starting your working day

A driver wearing a reflective vest inspects a tyre from outside a light truck parked on firm, level ground, with a chock against a rear wheel.
The key idea

Check your lorry before setting off and follow the manufacturer’s maintenance plan.

Remember

  • Check the outside, fluid levels and cab controls.
  • Secure your lorry on firm, level ground.
  • Never go under raised parts without their specified supports and locks.
  • Investigate significant leaks before using your lorry.
  • Record faults and tell the person responsible for maintenance.
  • Schedule fluid changes, filter changes and checks as the manufacturer specifies.

Exam trap: Wrong: recording a dangerous fault lets you drive. Right: have it corrected before driving.

Read the full explanation
  • Before setting off, walk all the way around the outside, check accessible fluid levels and finish in the cab with the controls and safety warnings.
  • Park on firm, safe and sufficiently level ground for your checks. Secure the vehicle and prevent anyone else from starting it while you work. Do not go underneath a tipping body, a tilted cab or a chassis with air suspension without the specified supports and locks in place.
  • Look at the ground and visible components for fresh stains, loose parts, impact damage, chafed pipes and leaks. What you see helps guide diagnosis: a stain can have several causes, but a significant fuel, oil or air leak requires you to find the cause before using the lorry.
  • Consult the vehicle handbook for pressures, fluids, intervals and checking methods. There is no universal tyre pressure or brake air pressure for all lorries. Record defects and report them to the person responsible for maintenance; recording a dangerous defect does not authorise you to drive with it.
  • Follow the manufacturer's preventive maintenance schedule according to time, mileage and operating conditions. You carry out daily checks and record problems; maintenance staff carry out work that requires specific training, tools or facilities.
  • Include these routine tasks in the plan, with their specific intervals and products: changing the engine oil and oil filter; replacing the fuel filter and attending to the water separator; checking and replacing the air filter and belts; replacing the coolant and, if the vehicle has a hydraulic braking circuit, the brake fluid. Have a workshop carry out these operations, except for tasks the handbook allows you to perform with suitable training and equipment.
  • Arrange with the workshop to replace the air dryer cartridge if fitted, lubricate the specified points and rotate the tyres where the manufacturer permits it; have a specialist carry out wheel alignment. As the driver, you monitor due dates and confirm that completed work is recorded.
  • Include inspections of the tachograph and speed limiter by the relevant authorised centres in your planning; consult “Inspections, seals and coefficients” in “The tachograph and its records” and the speed limiter sections of “Dimensions and masses of the light lorry” for their specific requirements.

2Exterior, chassis and driving position

A driver wearing a reflective vest checks the side latch of a parked light truck, with its side guards visible.
The key idea

Check the outside parts and prepare your driving position for safe driving.

Remember

  • Check catches, steps, panels and required guards.
  • Make sure the tilting cab is locked.
  • Look around your lorry before climbing in.
  • Adjust your seat, then your mirrors.
  • Check your seat belt and remove anything under the pedals.
  • Check the exhaust with the engine stopped; test your horn without causing a nuisance.

Exam trap: Wrong: you can see everything from your seat. Right: look around before climbing in.

Read the full explanation
  • Walk along both sides and around the front and rear, remembering the less visible areas. Check doors, fastenings, running boards, steps, mudguards and panels; a detached part can become an obstacle. Visually confirm that the bodywork and its accessories are secured for driving.
  • Check the condition and mounting of the sideguards and underrun protection applicable to the vehicle. You must check the devices required for your lorry and keep them secure and free of damage that prevents them from working; the bodywork may provide some of this protection according to its type approval. [RGV, arts. 11.16, 11.17 and 11.18](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).
  • Check that the tilting cab is locked, service covers are closed and no tools remain in moving areas. Before getting in, look at the immediate surroundings: a person, animal or object near the front may be out of sight once you sit down.
  • Adjust the seat, steering wheel and pedals so that you can operate the controls without stretching or bending your legs excessively; then adjust the mirrors from that position. Check the seat belt, door fastenings and that there are no objects under the pedals. Keep loose items in the cab secured so that they do not interfere with driving.
  • During your daily walk-round, check the accessible parts of the exhaust with the engine off: look for leaks, loose joints or mountings and damage to the silencer; arrange repairs if you find anything wrong.
  • Test the horn briefly in safe conditions and without causing a nuisance: it must produce a continuous, uniform sound of sufficient volume. If it fails or sounds abnormal, have it checked. [RGV, art. 11.7](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).

3Tyres: tread and damage

A person uses a tread-depth gauge to measure a groove in the front tyre of a light truck parked beside the kerb on its right, in the foreground.
The key idea

Check your tyre tread and look for damage.

1.0 mmN2 lorry minimum
1.6 mmO1 trailer minimum
Over 3.5 tonnesRegrooving only on vehicles
VehicleMinimum tread depth
N2 C1 goods lorry1.0 mm
O1 light trailer1.6 mm

Remember

  • Measure the main grooves in different places.
  • Do not drive with exposed cords, bulges or signs of tyre failure.
  • Do not judge safety by tread depth alone.
  • Ask a specialist to assess possible internal damage.
  • Regrooving deepens grooves; it differs from retreading.
  • Regrooving needs competent staff, weight above 3.5 tonnes and Regroovable or ∪ markings.

Exam trap: Wrong: your lorry and trailer have the same minimum. Right: check their categories.

Read the full explanation
  • On your category N2 C1 goods lorry, you must maintain a depth of at least 1.0 mm in the main tread grooves. On a category O1 light trailer, the minimum is 1.6 mm: do not automatically apply the lorry's value to the trailer. [RGV, Annex VII.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Measure the main grooves with a tread depth gauge and check different areas around the circumference. A single measurement in the least worn area can hide uneven wear. The legal minimum does not guarantee sufficient grip for every combination of rain, load and speed: you must also assess the general condition and intended use.
  • Examine the tread, shoulders and sidewalls; look for cuts, bulges, distortion, cracks and separation. You must preserve the markings and must not drive with exposed cords or signs of carcass failure. [RGV, Annex VII.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • The grooves help disperse water, but do not eliminate the risk of aquaplaning. A tyre that appears properly inflated may still be damaged by an impact or by being driven while flat. If there is structural damage, have a specialist assess it instead of relying solely on its outward appearance.
  • Regrooving means cutting the grooves deeper and is different from retreading. It is only permitted on tyres for vehicles with a maximum authorised weight of more than 3.5 tonnes that bear the marking Regroovable or the symbol ∪; you must have competent personnel carry it out. [RGV, Annex VII.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).

4Cold tyre pressures and wear

A person measures the pressure of the front right tyre of a light truck parked beside a kerb on its right, using a pressure gauge connected to the tyre valve.
The key idea

Measure cold tyre pressure using the manufacturer’s values for your axle and load.

CluePossible link
Low pressureMore heating and shoulder wear
Excessive pressureCentre wear
Wear on one edgeIncorrect wheel alignment

Remember

  • Use an approved, verified pressure gauge.
  • Do not release air from hot tyres to reach the cold pressure value.
  • Check valves and caps.
  • Find the cause if a tyre keeps losing pressure.
  • Treat wear patterns as clues you need to check.

Exam trap: Wrong: adjust hot pressure to the cold value. Right: follow the manufacturer’s procedure.

Read the full explanation
  • You must check tyre pressures regularly with an approved and verified pressure gauge. As a maintenance procedure, compare the cold measurement with the manufacturer's table for that axle, tyre arrangement, load and use; looking at how much the tyre deforms is no substitute for measuring its pressure. [RGV, Annex VII.6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • As you drive, the tyre heats up and its pressure usually rises. Do not release air from a hot tyre to match the recommended cold pressure: it becomes underinflated when it cools. If you need to assess a hot reading, follow the manufacturer's specific procedure and then confirm it under the specified conditions.
  • Low pressure increases carcass flexing and heat build-up and can encourage shoulder wear. If you see this pattern, cross-check the recorded pressures and have the tyre checked for damage caused by driving while underinflated. The effect on fuel consumption is covered in “Correct tyre pressures” in “Preventive and efficient driving”.
  • If you find wear in the centre, check whether you have used excessive pressure for the load and tyre arrangement. If only one edge wears, have the wheel alignment checked; if patches of wear appear, have the wheel balance and suspension checked. Record which wheel shows each wear pattern so that the workshop can relate it to its position and use: these are clues, not infallible diagnoses.
  • Check valves, valve caps and access to inflation points. Use the value specified for each axle without assuming that the front must always have a higher or lower pressure than the rear. If a tyre repeatedly loses pressure, locate the leak: inflating it every day does not repair the defect.

5Twin wheels and fastenings

A person uses a pressure gauge to check a tire in the rear dual-wheel assembly of a parked light truck secured with a wheel chock.
The key idea

Check the inner tyre too when your lorry has twin wheels.

Remember

  • Measure each tyre’s pressure separately.
  • Check that both tyres are compatible under the manufacturer’s guidance.
  • Secure your lorry before safely checking for stones between the tyres.
  • Check that the tyres do not rub together.
  • Have loose or damaged fastenings corrected before driving.

Exam trap: Wrong: checking the outer wheel is enough. Right: check the inner wheel and its valves too.

Read the full explanation
  • At each end of an axle with twin wheels, also access the inner tyre during your checks: inspect its tread and sidewalls with sufficient lighting and measure its pressure through its own valve. The outer tyre can hide damage or air loss in the inner one; record each reading separately to compare it with the specified value.
  • Check that the twin tyres are compatible in size, characteristics and wear according to the manufacturer. Significant differences in effective diameter or pressure alter load distribution and how the tyres work. A flat tyre forces its partner to bear excessive strain and can damage it too.
  • Look at the gap between the tyres and remove foreign objects only with the vehicle secured and using a safe method. A trapped stone can damage the sidewalls or be thrown out. Check that the tyres do not touch each other or rub against components, including the inner wheel and its valves.
  • Inspect rims, nuts and signs of loosening, such as movement or unusual marks around the fastenings. If you find a loose or damaged fastening, you must rectify it before driving.

6Remove and fit a wheel safely

A person wearing a reflective vest uses a wrench on the front wheel of a light truck parked on level ground, with chocks at a rear wheel, the jack set aside and the steering wheel beside the visible left door.
The key idea

Change a wheel only with suitable equipment and a safe place to work.

Remember

  • Choose firm, level ground away from traffic.
  • Apply the parking brake, stop the engine and chock the diagonally opposite wheel.
  • Loosen the nuts slightly while the wheel rests on the ground.
  • Use the specified jacking point; never go underneath with only a jack supporting you.
  • Tighten in a criss-cross pattern with a torque wrench; recheck as the manufacturer specifies.
  • For twin wheels or detachable rim rings, use a suitable inflation cage or specialist.

Exam trap: Wrong: a jack alone makes working underneath safe. Right: never go underneath with only that support.

Read the full explanation
  • To change a wheel, position the lorry on firm, level ground away from traffic, and apply the breakdown protection measures described in “Accidents, breakdowns and first aid”. If you cannot work protected from traffic, call for assistance.
  • Apply the parking brake, switch off the engine and chock the wheel diagonally opposite the one you are going to raise. Prepare a jack of suitable capacity, the wheel brace and the supports specified by the manufacturer; follow the procedure specific to your lorry and its suspension.
  • Slightly loosen the nuts with the wheel on the ground. Place the jack only at the lifting point specified by the manufacturer, raise the vehicle only as far as necessary and finish removing the nuts. Never go underneath a lorry supported only by a jack.
  • Use assistance or suitable handling equipment to remove and fit the heavy wheel without trapping your hands or feet. Check the mating surfaces and fastenings; with twin wheels, position the valves so that they line up with their access openings and you can reach both.
  • Position the wheel and nuts correctly and tighten progressively in a criss-cross pattern, following the manufacturer's tightening sequence and lowering procedure. Apply the specified torque with a suitable torque wrench and check it again after the first few kilometres, at the interval specified by the manufacturer.
  • To inflate twin wheels or wheels with detachable rim rings, use a suitable safety cage or have a specialist carry out the work. Do not remove rings or components while any pressure remains, and do not stand in the path of any part that could be thrown out.

7Read the tyre markings

A hand holds a magnifying glass over a band of abstract raised markings on the tire sidewall of a parked orange light truck.
The key idea

Read tyre markings to choose tyres suitable for your lorry.

385Nominal width in millimetres
65Height as percentage of width
22.5Rim diameter in inches
Tyre markingMeaning
RRadial construction
149/145First: single fitment; second: twin fitment
MTechnical capability: 130 km/h
NTechnical capability: 140 km/h

Remember

  • Use the load-index table to convert load indices.
  • Do not read load indices as kilograms.
  • With TUBELESS tyres, check that the rim and valve do not leak air.
  • Fit approved sizes and characteristics, or permitted equivalents.
  • Keep the tyre’s technical speed capability separate from your legal speed limit.

Exam trap: Wrong: load indices mean front and rear axles. Right: they mean single and twin fitment.

Read the full explanation
  • In 385/65 R22.5, you must interpret 385 as the nominal width in millimetres, 65 as the percentage ratio of section height to width, R as radial construction and 22.5 as the nominal rim diameter in inches. Do not confuse this diameter with the tyre's width, pressure or outside diameter. [UN Regulation 54, sections 2 and 3](https://www.boe.es/doue/2008/183/L00041-00076.pdf).
  • In load indices such as 149/145 or 150/146, the first applies to single fitment and the second to twin fitment. You must convert them using the load index table: they are not weights written directly in kilograms and do not identify the front and rear axles. [UN Regulation 54, section 2.27 and Annex IV](https://www.boe.es/doue/2008/183/L00041-00076.pdf).
  • The speed symbol indicates a technical capability of the tyre: M corresponds to 130 km/h and N to 140 km/h. You must distinguish this from the lorry's legal speed limit; the symbol does not authorise you to reach that speed. [UN Regulation 54, section 2.28](https://www.boe.es/doue/2008/183/L00041-00076.pdf).
  • With a TUBELESS fitment (without an inner tube; see “Tyre construction” in “Lorry mechanics and checks”), check that the rim and valve are airtight. [UN Regulation 54, section 3.1.7](https://www.boe.es/doue/2008/183/L00041-00076.pdf).
  • You must fit tyres with approved dimensions and characteristics, or permitted equivalents. When comparing products, distinguish load capacity and speed capability from the fuel efficiency, wet grip and noise performance shown on the label: no label specifies a universal pressure or promises an exact service life. [RGV, Annex VII.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).

8Snow chains and equipment

A light truck is stopped in a layby beside a snowy road, with chains on both wheels of the rear driven axle and no chains on the visible front wheel.
The key idea

Prepare suitable snow equipment and obey the restrictions on your route.

3,500 kgSpecial tyres: MMA above

Remember

  • When required, fit chains to at least one driven wheel on each side.
  • Check compatibility and follow the fitting instructions.
  • Do not choose the front wheels just because they steer.
  • For winter restrictions, an M+S marking alone is not enough.
  • Chains do not let you pass a restriction banning lorries.

Exam trap: Wrong: any M+S tyre meets winter restrictions. Right: when using special tyres above 3,500 kg MMA, fit certified 3PMSF or POR tyres to at least the steering and driven axles.

Read the full explanation
  • When chains or other authorised anti-skid devices are required, you must fit them to at least one driven wheel on each side, or use the special tyres provided for in the regulations. On a rear-wheel-drive lorry, the fact that the front wheels steer does not make them the wheels to which you fit chains. [RGV, art. 12.5.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • Prepare chains compatible with the tyre size, twin-wheel fitment, wheel arches and nearby components. Check which wheel you must equip at each end of the axle for the system you use; do not improvise with twin wheels or vehicles with several driven axles. Practise fitting them in a safe area before you need them.
  • To comply with winter travel restrictions by using special tyres, on vehicles with an MMA (maximum authorised mass) above 3,500 kg you must fit 3PMSF- or POR-certified tyres at least on the steering axle and the driven axles. The M+S marking alone does not indicate this certified equipment. [RGV, Annex VII.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • The 3PMSF pictogram shows a three-peaked mountain with a snowflake; POR identifies professional off-road use. In both cases, the special tyres also bear M+S, M&S or M.S. Check the conditions for the road section: suitable equipment does not authorise you to drive where a restriction prohibits lorries. [RGV, Annex VII.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Fit and tension the chains according to the instructions, check that they are seated correctly when required and remove them when conditions require it. Follow the applicable instructions and restrictions. Their traction assistance does not guarantee safe braking or steering on ice.

9Oil: level, pressure and topping up

A person holds an oil dipstick and a cloth beside the open bonnet of a light truck parked in a level parking bay next to the kerb.
The key idea

Keep oil level and pressure separate, and act on warning lights.

CheckWhat it tells you
Dipstick or level indicatorAmount of oil
Pressure gaugePressure in the circuit

Remember

  • Check the level with your engine stopped and lorry level, following the manual.
  • Keep oil between the minimum and maximum marks.
  • If a pressure warning appears with the engine running, stop safely and switch off.
  • Add approved oil in small amounts through the correct filler.
  • Investigate leaks or increased oil use.

Exam trap: Wrong: enough oil guarantees correct pressure. Right: level and pressure are different.

Read the full explanation
  • To check the level, you must position the lorry on level ground, switch off the engine and follow the manufacturer's temperature and waiting-time requirements. If you use a dipstick, wipe it clean and reinsert it to obtain a correct reading; if you have electronic measurement, meet its operating conditions. Keep the level between minimum and maximum, without filling above maximum.
  • Level and pressure measure different things: the dipstick or level indicator tells you the quantity; the pressure gauge tells you the pressure in the circuit. Having enough oil does not ensure that the pump and oilways provide correct lubrication. A pressure warning with the engine running requires you to stop safely and switch off the engine as instructed in the manual.
  • Top up through the identified filler opening, adding small amounts and checking the result. Do not confuse the oil filler with the coolant or hydraulic fluid filler, or with the sump drain plug. Use an approved viscosity and specification; mixing products without knowing their compatibility can impair lubrication.
  • If consumption increases or leaks appear, you must investigate the cause. Persistent bluish smoke together with oil consumption can indicate that oil is entering the combustion chamber, but does not automatically identify piston rings or valves as the cause.
  • Check the maintenance record to ensure that oil and filter changes are up to date; for lubricant selection, see “Lubricant pressure and selection” in “Lorry mechanics and checks”.

10Coolant and overheating

A driver wearing a reflective vest waits on the pavement beside a stopped light truck, with its bonnet raised and the coolant reservoir cap closed as heat rises from the engine.
The key idea

Check coolant when cold and stop safely if your engine overheats.

Remember

  • Check the level against the marks and leave room for expansion.
  • Use the specified coolant and concentration.
  • Never open a hot, pressurised cooling-system cap.
  • For a temperature alarm or significant loss, stop safely and follow the manual.
  • Keep your hands away from belts and fans.
  • Investigate repeated losses or unusual mixing of oil and coolant.

Exam trap: Wrong: matching colours guarantee compatibility. Right: use the manufacturer’s specified coolant.

Read the full explanation
  • You must check the coolant with the cooling system cold and under the manufacturer's specified conditions, using the marks on the expansion tank. Leave the specified expansion space. If the level repeatedly drops, you must have the system checked; topping up does not fix a faulty hose, radiator or gasket.
  • Use coolant of the prescribed specification and concentration, suitable for the cold conditions you expect. Distinguish concentrated coolant from a ready-to-use mixture; do not add water to the latter unless its instructions allow it. Colour alone does not prove that different products are compatible.
  • Do not open a hot, pressurised cooling system cap: escaping steam and liquid can burn you. You must stop safely if you receive a temperature alarm or suffer a major coolant loss, follow the manual and allow the system to cool before carrying out any permitted checks. A fixed temperature figure does not replace the instructions for your engine.
  • Inspect accessible hoses, clips, the radiator and belts with the engine switched off. If the pump depends on a damaged belt, coolant circulation can fail; other designs and causes of overheating also exist. Keep your hands away from belts and fans, which can start automatically.
  • If you detect oil in the coolant, an abnormal emulsion in the oil, or leaks accompanied by overheating, seek a diagnosis. There may be an internal connection between the circuits, but these signs alone do not confirm a failed cylinder head gasket. You must resolve the contamination and its cause before using the engine normally.

11Other fluids and filters

A worker replenishes AdBlue through the blue filler of a light truck parked beside the kerb on its right side, while the diesel tank remains closed.
The key idea

Put each fluid in its correct tank and follow the filter and belt schedule.

Power steering typeFluid check
HydraulicCheck its reservoir as the manual specifies
Entirely electricNo power steering fluid

Remember

  • Check fuel levels and look for leaks.
  • If you use AdBlue, put only the specified product in its dedicated tank.
  • If you mix AdBlue and diesel, get assistance before starting.
  • Check any hydraulic reservoirs your lorry has, following the manual.
  • Do not remove the air filter to keep working.
  • Replace the timing belt as the manufacturer specifies; do not grease it.

Exam trap: Wrong: any similar fluid will do. Right: check the specified product for each system.

Read the full explanation
  • Check that you have enough fuel for the job and that there are no leaks from tanks or visible fuel lines. If your lorry uses AdBlue, monitor its level and top up only with the prescribed product through its dedicated filler opening. Do not mix it with diesel: confusing the tanks can cause damage and requires assistance before you start the engine.
  • With hydraulic power steering, you must check the correct reservoir, its marks and the specified checking method. Purely electric steering does not have this fluid. A low level, foam, noise or heavy steering requires investigation; do not fill above maximum or choose a fluid just because it looks similar.
  • If you have a hydraulic clutch or hydraulic brakes, check their reservoirs according to the manual. They may share a reservoir or have separate ones; they are not necessarily next to the pedal. If the level drops, you must find out whether wear or a leak is responsible, and follow the fluid replacement interval.
  • You must follow the maintenance schedule for air filters, fuel filters and filters in other circuits. A clogged intake filter can impair operation and be associated with abnormal black smoke from a diesel engine; smoke alone does not confirm that fault. Do not remove the filter to continue working or clean any filter element using an unauthorised method.
  • The gearbox, differential and hydraulic equipment may require lubricants different from engine oil. Check their levels only through the specified access points and under the specified conditions. Do not replace the specified oil with the thickest oil or apply the same procedure to a manual and an automatic gearbox.
  • If the valve timing system uses a toothed belt, you must replace it at the specified interval and must not grease it. Also check auxiliary belts according to their maintenance schedule: a broken belt can affect several systems. Do not adopt a single mileage interval for all engines or always wait for a noise to appear before scheduling replacement.

12Exterior lighting and signalling

A person wearing a reflective vest checks the illuminated rear lights of a light truck parked beside the right-hand kerb and holds a cloth beside one lamp.
The key idea

Test all your exterior lights and keep them clean.

2.10 mOutline markers: width above
6 mSide lamps: length above
Lorry lighting deviceWhen to check it
End-outline marker lampsWidth above 2.10 m
Side position lampsLength above 6 m; chassis-cab exceptions apply

Remember

  • Check both sides and the rear with safe assistance.
  • Clean headlamps, reflectors and reflective surfaces.
  • Check for cracks, moisture and loose mountings.
  • If an indicator flashes unusually quickly, check lamps and connections.
  • With reduced lighting from an unrepairable fault, slow enough to stop within the light.

Exam trap: Wrong: a dashboard indicator proves all lamps work. Right: check the exterior lamps themselves.

Read the full explanation
  • You must test the position lights, dipped beam, main beam, direction indicators, hazard warning lights, brake lights, reversing lights and number plate lighting, as well as any other devices fitted. Check both sides and the rear with safe assistance or the lorry's checking system. Seeing the dashboard indicator illuminated does not prove that all exterior lamps work.
  • Clean lamp lenses, retroreflectors and reflective surfaces without damaging them. Check for cracks, moisture and secure mountings; dirt reduces range and visibility. Paired devices serving the same purpose must match in colour and intensity and be symmetrical in accordance with their regulations. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15).
  • Include end-outline marker lamps in your checks when the lorry exceeds 2.10 m in width, and side marker lamps when it exceeds 6 m in length, subject to the regulatory exceptions for chassis-cabs. A correctly working headlamp does not compensate for inadequate marking of the lorry's outline. [RGV, art. 16 and Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • If the dashboard indicator flashes unusually quickly, check whether a direction indicator has failed. Also check connections, especially if you are towing a trailer; do not automatically attribute the symptom to a short circuit or regard it as confirmation of correct operation.
  • If a fault that cannot be repaired en route forces you to drive with reduced lighting intensity, you must reduce your speed until you can stop within the illuminated area. Find a safe way to stop the vehicle and have it repaired. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107).

13Lamps and headlamp alignment

A light truck travels with its headlights illuminating the road ahead while a car drives away in the opposite lane on a rural road.
The key idea

Keep headlamps correctly aimed and replace bulbs only as the manual allows.

Remember

  • Check load, tyre pressure and suspension conditions before adjusting headlamps.
  • Do not guess how to adjust an automatic system.
  • Before an allowed halogen replacement, switch off the circuit and let the bulb cool.
  • Hold the bulb by its base without touching the glass.
  • Use the authorised type and power; close the lamp unit properly.
  • Ask a workshop to handle work beyond your training or equipment.

Exam trap: Wrong: aiming headlamps as low as possible is correct. Right: follow the alignment procedure.

Read the full explanation
  • You must keep the beam correctly aligned so that you can see without dazzling others. Adjustment may include vertical and horizontal alignment; it does not mean lowering the headlamps as far as possible or changing the physical width of the lamp unit. Before measuring alignment, follow the procedure's requirements for load, pressure and suspension.
  • Do not alter the settings of an automatic system by guesswork. Some headlamps require a beam tester, diagnostic equipment or calibration; you can only use a wall if the procedure allows it. A headlamp levelling device compensates for certain changes in load, but it does not repair a loose or incorrectly fitted headlamp.
  • If the manual allows you to replace a halogen bulb, switch off the circuit, let the bulb cool and handle it by the base without touching the glass with your fingers. Use the approved type and wattage and close the lamp unit correctly afterwards. Grease on the glass can damage the bulb.
  • You must have a workshop carry out work beyond your training or equipment, especially on high-voltage xenon systems and integrated LED units. The absence of a general requirement to carry spare bulbs does not remove your responsibility to maintain the lights.

14Mirrors and vision aids

A driver seated at the wheel of a light truck parked beside the kerb has two visible main exterior mirrors, one on each side of the cab.
The key idea

Check the condition and adjustment of your mirrors and cameras.

Installed vision deviceWhat to check
MirrorsCleanliness, mountings and adjustment; stable image
Cameras and monitorsLenses, power, image and absence of faults

Remember

  • Clean and adjust mirrors from your driving position.
  • Check housings, arms and mountings; arrange repairs for cracks or movement.
  • When replacing mirrors, keep the approved equipment and specifications.
  • Check camera lenses, screens and images.
  • After impacts or washing, check adjustment.
  • Test electric adjustment and demisting if fitted.

Exam trap: Wrong: any camera replaces a required mirror. Right: only a system approved for that function can do so.

Read the full explanation
  • Clean the viewing surfaces and check the housings, arms, mountings and adjustment mechanisms of the mirrors fitted. Look for cracks, loss of reflective coating or movement that prevents a stable image; arrange for the faulty component to be repaired before relying on it when driving.
  • When replacing a mirror or its support, you must retain the assembly's approved equipment and specifications; consult the mirror classes and installation requirements for your C1 in “What each mirror class shows” in “Lorry driving techniques”. [RGV, Annex III.2 and notes (2) and (3)](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • If you have cameras and monitors, check the lenses, image, start-up and absence of faults. An approved system can provide indirect vision, but an ordinary auxiliary camera does not automatically replace a compulsory mirror. You must have a faulty screen or lens repaired according to the vehicle's configuration.
  • After an impact or a wash, check from your driving position that the adjustment lets you see the intended areas; a mounting that vibrates needs repair even if you can adjust the mirror glass. Also test electric adjustment and demisting if fitted, following the manual.

15Windscreen, wiper blades and washers

A person wipes the windscreen of a green light truck parked beside the kerb with a cloth, with the wipers resting at the base of the glass.
The key idea

Keep your windscreen clean and check the systems that help you see.

Remember

  • Clean the glass inside and outside.
  • Check for cracks, impact damage and objects blocking your view.
  • Test wipers, washer pump and washer jets.
  • Replace hardened, cracked or torn wiper blades.
  • Use compatible washer fluid suitable for cold conditions.
  • Remove ice before using wipers, and check demisting.

Exam trap: Wrong: wipers remove mist inside. Right: use demisting and ventilation.

Read the full explanation
  • You must keep the glass clean inside and out, with no objects obstructing the field of vision you need. Check for impact damage, cracks and distortion; laminated glass can hold fragments together and still prevent you from seeing clearly. [RGC, art. 19](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a19).
  • Test the wipers and look for streaks, juddering or areas left unwiped. First check for dirt, incorrect adjustment and mechanism faults; if the rubber is hardened, cracked or torn, you must replace it.
  • Regularly check the screenwash fluid, pump and jets. Top up with a compatible product that provides suitable protection against the cold you expect, respecting the level and dilution requirements. Do not confuse this reservoir with the cooling system or add household detergent or engine antifreeze on your own initiative.
  • Avoid operating the wipers over ice stuck to the glass or on a dry, very dirty windscreen. You must remove the obstruction using the correct procedure to avoid damaging the rubber and mechanism. Also check demisting and ventilation: the exterior wipers do not clear condensation inside.

16Steering and suspension: signs of faults

A person wearing a reflective vest visually inspects the leaf springs of a light truck facing right and parked beside the kerb on its right-hand side.
The key idea

Investigate steering and suspension changes before they affect your control.

Part or taskPurpose
Wheel balancingDistributes wheel mass evenly
Wheel alignmentAdjusts wheel geometry
Springs and leaf springsSupport weight and absorb road bumps
DampersReduce bouncing

Remember

  • If a fault affects safety, stop and request a check.
  • Do not release the steering wheel to test whether your lorry pulls sideways.
  • Inspect springs, leaf springs, dampers and mountings; do not dismantle parts under load.
  • Restore driving height after loading or unloading.
  • Never work underneath relying on air suspension to maintain its height.

Exam trap: Wrong: balancing and alignment are the same. Right: they correct different things.

Read the full explanation
  • You must investigate stiffness, free play, noises and changes in steering response. If power assistance fails, steering effort can increase and compromise control; do not continue a journey relying on your arms to compensate for any fault. Stop in a controlled manner and arrange an inspection when safety is affected.
  • Steering wheel vibration at certain speeds may be related to wheel imbalance; a persistent tendency to pull to one side may require checks of alignment, tyres or suspension. Balancing correctly distributes mass around the wheel and tyre assembly; alignment adjusts its geometry. Do not let go of the steering wheel to check whether the vehicle pulls to one side.
  • Inspect leaf springs, coil springs, shock absorbers and their mountings without dismantling components under load. The spring components support the vehicle and absorb road irregularities; the shock absorbers damp their oscillations. If the shock absorbers lose effectiveness, wheel contact with the road and stability deteriorate, and braking distance may increase.
  • With air suspension, check visible air springs, leaks and ride height. You must restore the specified driving position after loading or unloading. Automatic adjustment does not permit overloading or guarantee levelling if there is a leak; you must not work underneath relying on the air to maintain the height.

17Brakes: test before driving

A driver seated on the left side of a light truck checks the brakes in a clear yard marked by cones, with a rear brake light illuminated.
The key idea

Test your brakes safely before joining traffic.

Remember

  • Identify whether your brakes use hydraulic pressure, air pressure or both.
  • Check service, secondary and parking brakes as the manufacturer specifies.
  • Test at very low speed in a clear, authorised area.
  • If braking pulls sideways or your pedal feels spongy, request inspection before continuing.

Exam trap: Wrong: you may set off with a spongy pedal. Right: request a check before driving.

Read the full explanation
  • Identify whether your C1 has hydraulic, pneumatic or combined brake actuation, and check the service, secondary and parking brakes using the manufacturer's safe procedures. [RGV, art. 12.8 and Annex VIII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • Before joining traffic, check pedal response, braking effectiveness and the absence of pulling to one side or abnormal noises at very low speed in a clear area where you are authorised to do so.
  • If the vehicle pulls to one side when braking or the pedal feels spongy, arrange an inspection before continuing. Report the symptoms so that the brakes, tyres and related components can be checked; check that the hydraulic brake pedal retains its usual feel and travel (see “Hydraulic circuits and wet brakes” in “Brakes and retarders on light lorries”).
  • Heed wear warnings and have a workshop carry out work on discs, drums, actuators and adjustments that require specific training.

18Air system: pressure and leak-tightness

A driver waits at the wheel of a light truck stopped beside the right-hand kerb, with both air pressure gauges below the green zone and a warning light illuminated.
The key idea

Wait for working air pressure and check that your system does not leak.

Remember

  • Check each circuit’s pressure gauges and warnings.
  • Wait for the specified pressures and for the relevant warnings to clear.
  • Request a check if filling takes too long or pressure falls quickly.
  • Secure your lorry and check for leaks using the manufacturer’s procedure.
  • Have abnormal leaks corrected before starting work.

Exam trap: Wrong: a running engine allows driving with insufficient pressure. Right: wait until working conditions are met.

Read the full explanation
  • With air brakes, check each circuit's pressure gauges and warnings; the air path is explained in “The compressed air path” in “Brakes and retarders on light lorries”.
  • Wait until the circuits reach the operating pressures specified by the manufacturer and the relevant warnings disappear before setting off.
  • Monitor the pressure build-up time and changes in pressure: if it takes unusually long, fails to reach the specified value or drops rapidly again, arrange an inspection.
  • With the lorry secured, check for leaks using the manufacturer's procedure, times and tolerances; consult “Leaks and loss of effectiveness” in “Brakes and retarders on light lorries” to interpret the pressure loss.
  • Inspect accessible pipes and connections and listen for possible leaks from a safe position; arrange for any abnormal leak to be repaired before putting the lorry into service.

19Dryer, air reservoirs and spring brakes

A mechanic uses a flashlight to inspect the air dryer and air reservoirs of a light truck parked beside the curb on its right side, shown in the foreground.
The key idea

Check the air dryer and reservoirs without interfering with spring brakes.

Remember

  • Report unusual water or oil in drained liquid.
  • Check automatic drainage.
  • Drain manually only when the manufacturer specifies it.
  • Leave pressure-regulation faults to qualified staff.
  • Check that spring brakes apply and release correctly.
  • Never dismantle spring brake chambers or use mechanical release to drive.

Exam trap: Wrong: draining water means bleeding hydraulic brakes. Right: these tasks involve different systems.

Read the full explanation
  • Check the condition and maintenance of the dryer and air reservoirs; report abnormal amounts of water or oil in the condensate.
  • Check that the automatic drain works, or drain manually only if the manufacturer specifies it; see “Dryer, moisture and drainage” in “Brakes and retarders on light lorries”.
  • Have qualified personnel deal with any fault in pressure regulation or overpressure protection; use only products expressly specified for the system.
  • Check that the spring brakes apply and release according to the vehicle's procedure, without dismantling their chambers or operating their mechanical release to drive; see “Spring brake actuators” in “Brakes and retarders on light lorries”.

20ABS, moisture and brake heating

A light truck travels along a wet road among Mediterranean hills, with the driver wearing a seat belt and holding the steering wheel with both hands.
The key idea

Check brake warnings and stop if your brakes lose effectiveness.

Remember

  • Watch the ABS and EBS self-check and follow the manual.
  • If a warning indicates critical brake failure, stop and request repairs.
  • After driving through water, check your brakes safely.
  • If braking stays weak or uneven, stop and request assistance.
  • For reduced response, unusual smells or overheating, stop and request a check.
  • Check retarder warnings and temperature limits.

Exam trap: Wrong: keep driving if wet brakes stay ineffective. Right: stop and request assistance.

Read the full explanation
  • Observe the ABS and EBS self-check and follow the manual's instructions if a warning persists; if it indicates a critical braking fault, immobilise the vehicle and request repairs (the emergency braking technique is explained in “ABS and wheel lock” in “Brakes and retarders on light lorries”).
  • After driving through water, check the brakes' response when you can do so safely; if their effectiveness does not recover or they respond unevenly, stop and request assistance (see “Hydraulic circuits and wet brakes” in “Brakes and retarders on light lorries”).
  • If the brakes lose responsiveness, give off an abnormal smell or show abnormal signs of heat, stop safely and request an inspection; see “Brake fade and long descents” in “Brakes and retarders on light lorries”.
  • Check the retarder warnings and availability according to the manual, including its temperature limits and maintenance instructions.

21Trailer coupling and connections

A person checks the hitch of a small trailer with a chocked wheel, connected to a parked light truck by the coupling, a safety chain and an electrical cable.
The key idea

Check that your trailer is permitted, securely coupled and correctly connected.

750 kgC1 trailer maximum MMA
Up to 1,500 kgTrailer without breakaway braking
Trailer caseDevice to check
Up to 1,500 kg MMA without automatic braking if the coupling breaksRequired secondary coupling
Automatic braking operated by a cableOperating cable; different from a secondary restraint

Remember

  • Check your lorry’s technical towing limits too.
  • Secure the trailer and clear the area before approaching.
  • Check the coupling is closed and secured; hearing a clunk is not enough.
  • Keep everyone out of the crushing zone.
  • Check cables, lights and any connections your combination has.
  • Raise supports and check all locks are in their driving positions.

Exam trap: Wrong: a compatible coupling extends your licence. Right: with C1, your trailer cannot exceed 750 kg MMA.

Read the full explanation
  • If you tow a trailer, you must check the coupling, locking mechanism and safeguard against accidental opening. The C1 licence allows a trailer with an MMA (maximum authorised mass) of no more than 750 kg; a technically compatible coupling does not extend that entitlement. Also check the towing vehicle's technical limits. [RGCond, art. 4.2](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • Before bringing the vehicles together, secure the trailer and clear the area. You must check the device's compatibility, condition and locking according to its manufacturer's instructions, and confirm that it has actually locked; hearing a bang is not enough. Do not remain or allow anyone else to remain in a crush zone while the vehicles approach each other.
  • Check the applicable secondary coupling or safety device. A secondary coupling is required on trailers with an MMA of no more than 1,500 kg that have no system to ensure braking if the coupling breaks. Do not confuse this restraint with the cable that activates an automatic braking system. [RGV, art. 13.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Check the plug, lights and cable routing: they must allow movement without dragging, becoming taut or getting trapped. If the system includes pneumatic connections, you must check their identification, compatibility, seals, fastening and leak-tightness, following the sequence for that combination. Do not apply semi-trailer connection procedures to a light trailer that has no such connections.
  • Retract the jockey wheel and any supports provided, and confirm that all locking devices are in their travelling positions. You must check the coupling for play, deformation, cracks and excessive wear; do not improvise repairs with wire or replace its safety device with an arbitrary part. Before setting off, check that the trailer is correctly coupled and its lights work.

22Interpret dashboard warning lights

View from behind the driver of a light truck, seated on the left, switching on the ignition and checking the illuminated oil pressure warning lamp on the dashboard while parked.
The key idea

Read each dashboard warning using its symbol, message and your manual.

Remember

  • Check the warning lights come on and go out correctly when switching on.
  • A warning light that never lights may be faulty.
  • Learn oil, cooling, charging and brake warnings.
  • For a stop instruction, find somewhere safe with the urgency indicated.
  • Do not disconnect the battery to clear faults.
  • Report symptoms and follow instructions for engine, emissions or AdBlue warnings.

Exam trap: Wrong: a yellow warning always allows driving. Right: read the symbol, message and manual.

Read the full explanation
  • When you switch on the ignition, you must check that the specified warning lights come on and then follow their self-check sequence. A warning light that never comes on may be faulty; its being off does not by itself prove that the system is working properly. Learn the symbols and messages in that vehicle's manual.
  • Identify the oil pressure warning light and check that it goes out after starting the engine; to respond if it stays on or comes on while driving, follow the section “Oil: level, pressure and topping up”.
  • Identify the coolant temperature gauge or cooling warning and the specific dashboard message; to check the circuit and respond to overheating, follow “Coolant and overheating”.
  • In a conventional system, the charging warning light usually comes on with the ignition and goes out when you start the engine. If it comes on while driving, the alternator, regulator or wiring may be faulty; you must assess the manufacturer's instructions and the systems affected. A light that is off does not mean the battery is fully charged or guarantee the absence of electrical faults.
  • Distinguish the parking brake applied indicator from a low-pressure, service brake fault or ABS warning. The colour gives you a guide to priority, but you must read the symbol and message: not all red warning lights have the same cause, and an amber light does not always allow you to continue. If you receive an instruction to stop, find a safe place with the appropriate urgency.
  • If an engine, emissions or AdBlue level warning appears, consult the action indicated and arrange the necessary work. Do not clear faults by disconnecting the battery or continue your journey while ignoring a major loss of power, abnormal smoke or a risk to traffic. You must report the symptoms to help with diagnosis.

23Battery, isolator and fuses

A mechanic wearing safety goggles and protective gloves uses a flashlight to inspect the battery connections of a light truck parked beside the right-hand kerb, with the battery compartment open.
The key idea

Check batteries and fuses using the specified voltage and parts.

12 VEach battery in this comparison
24 VResult of series connection
Connection of two compatible 12 V batteriesVoltageNominal capacity
Series24 VAmpere-hours do not add together
Parallel12 VCapacities add together

Remember

  • If the dashboard has no power, check the isolator if fitted.
  • Do not open or refill sealed, AGM or gel batteries.
  • For serviceable vented batteries, top up only with the specified water.
  • Keep away sparks, flames and objects that could bridge terminals.
  • For authorised jump starts, follow the specified voltage, polarity and connection points.
  • Never bypass fuses or increase their amperage; investigate if they blow again.

Exam trap: Wrong: connect 24 V to a 12 V system. Right: use the same nominal voltage.

Read the full explanation
  • If the dashboard receives no power when you switch on the ignition, you must check the position of the master isolator, where fitted, according to the manual. The battery, terminals or protective devices may also be faulty. Operate the isolator with the engine running only if the procedure expressly provides for it.
  • On a serviceable flooded lead-acid battery, check cleanliness, fastening, connections and electrolyte level according to the instructions. Top up only with the specified water, normally distilled, without adding acid or tap water. Do not open or top up a sealed, AGM or gel battery.
  • Keep vents clear and avoid flames, sparks and short circuits near batteries. You must protect yourself against electrolyte and avoid working with jewellery or conductive objects that could bridge the terminals. Cleaning connections and protecting them against corrosion does not eliminate every internal sulphation process.
  • Two compatible 12 V batteries connected in series provide a nominal 24 V; in parallel they retain 12 V and their nominal capacities add together. In series, you do not add the ampere-hour capacities. Consult the manual or the vehicle's identification labels for the combined voltage and service points; you cannot deduce them from the number of visible batteries.
  • For an authorised jump start, use a source with the same nominal voltage, the correct polarity and the specified connection points. Do not connect 24 V to a 12 V system or improvise the earth connection point or the order of the clamps. You must reject damaged or frozen batteries and follow the specific procedure to protect electronics and people.
  • A fuse protects against overcurrent. Replace it with the specified type and amperage, with a suitable voltage rating; do not bypass it or increase its current rating to stop it blowing. If it blows again, you must locate the fault: replacing it repeatedly does not repair the circuit.

24Locate the fault and carry out minor repairs

A person wearing a reflective vest consults the manual beside the open fuse compartment of a light truck parked at the right-hand kerb, with the steering wheel on the far side of the cab on the vehicle’s left.
The key idea

Find the cause safely and carry out only repairs your manual allows.

Remember

  • Secure your lorry in a safe place.
  • Identify the symptom, warning light and message.
  • Check simple, accessible causes that match the symptom.
  • Isolate power or release pressure only through the specified procedure.
  • Use suitable tools and compatible parts.
  • Afterwards, check operation; if the fault remains, request assistance.

Exam trap: Wrong: loosen a pressurised pipe to find leaks. Right: release pressure as the manufacturer specifies.

Read the full explanation
  • With the lorry immobilised in a safe place, identify the symptom, warning light and dashboard message. Consult the manual to relate them to the affected system: electrical, cooling, lubrication or air. This helps you narrow down possible causes before working on it.
  • First check simple, accessible causes: the master isolator's position if there is no power, the circuit fuse, visible connections, fluid levels and air pressure, according to the symptom. Isolate the system before working on it: cut off its power supply or release pressure only using the manufacturer's procedure. Do not loosen a pressurised pipe to look for a leak.
  • Use the vehicle's tool kit and the compatible spare parts you carry: a fuse puller, suitable spanners and screwdrivers. You may replace a fuse or an accessible bulb if the manual allows it; the procedures are in the battery and lamp sections.
  • After the repair, check operation and that the symptom has disappeared according to the manual. If the fuse blows again, a leak persists or the fault affects the brakes, steering or systems that require specialist equipment, stop the work and request assistance. Report what you observed, what you checked and which part you replaced.

25Breakdown while driving: decide and stop

A light truck with a flat rear tyre is stopped off the carriageway in a paved area on its right, with an illuminated amber beacon on the cab roof.
The key idea

Keep control and stop safely when a dangerous fault occurs.

Remember

  • Do not continue if the fault affects your control of the lorry.
  • After a tyre bursts, hold the wheel firmly; avoid harsh braking or sudden steering.
  • Slow down gradually and pull off when safe.
  • With twin tyres, check the partner tyre after a burst.
  • If a gear grates, do not force the lever.
  • Report location, travel direction and symptoms; mention fuel leaks, fire risks or dangerous goods.

Exam trap: Wrong: a running engine means you can reach a workshop. Right: stop if the fault affects safety.

Read the full explanation
  • If you notice noises, vibrations, a burning smell or changes in how the vehicle responds, maintain control and look for somewhere to stop safely. The fact that the engine keeps running does not mean it is safe to continue. If a gear grates, do not force the gear lever: the clutch or synchromesh may need checking, but the noise alone does not allow a definitive diagnosis.
  • If a tyre bursts or suddenly loses pressure, hold the steering wheel firmly and avoid harsh braking and violent steering corrections. Reduce your speed progressively and pull aside when you can do so safely. With twin tyres, you must also check the other tyre: it may have been overloaded or damaged.
  • Changing a heavy wheel may require professional recovery assistance; to move the vehicle aside and secure it, consult “Move the lorry aside and secure it” in “Accidents, breakdowns and first aid”.
  • If the brakes, steering, lubrication or cooling are compromised, stop operating the vehicle and request assistance instead of trying to reach a workshop; follow “Move the lorry aside and secure it” in “Accidents, breakdowns and first aid”.
  • Tell the breakdown assistance service your location, direction of travel, registration number, relevant dimensions and symptoms. You must state whether there is a fuel leak, a fire risk or dangerous goods, and call the emergency services if there is immediate danger. Actions involving casualties and emergencies in tunnels are covered in “Accidents, breakdowns and first aid”.

26Breakdown signalling and emergency equipment

A light truck is stationary off the roadway with an illuminated V-16 beacon on the cab roof and a reflective vest and fire extinguisher accessible inside.
The key idea

Keep your emergency equipment ready and within reach.

Remember

  • Check your V-16 beacon is connected and certified.
  • Keep it accessible from the cab, with working power and valid connectivity.
  • Carry a high-visibility vest and suitable, usable, approved fire extinguisher.
  • Check the vest’s condition and accessibility.
  • Check the extinguisher’s mounting, seal and maintenance.

Exam trap: Wrong: triangles replace a connected V-16. Right: check you carry the required beacon.

Read the full explanation
  • Before setting off, check that your connected and certified V-16 is accessible from the cab, has power and has an active connectivity service; placement is explained in “Connected and certified V-16” and “Place the beacon without putting yourself at risk” in “Accidents, breakdowns and first aid”. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • Check that you carry a high-visibility vest and suitable, usable, type-approved fire-extinguishing equipment, as well as the beacon. Consult “Emergency equipment and fire extinguishers according to MMA (maximum authorised mass)” in “Accidents, breakdowns and first aid”. [RGV, Annex XII.1 and 2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • Check the condition and accessibility of the vest, and the extinguisher's mounting, seal and maintenance in accordance with its instructions; use of the vest is explained in “Put on your high-visibility vest before getting out” in “Accidents, breakdowns and first aid”.

27ITV (vehicle roadworthiness test): frequency and preparation

An inspector holding a blank report checks the headlamp and front wheel of a goods truck at a vehicle inspection station with a numberless calendar on the wall.
The key idea

Arrange your lorry’s ITV according to its age and prepare it for inspection.

10 yearsFrequency changes above this age
30 daysCalendar days early: reference retained
Age of N2 C1 goods lorryPeriodic ITV
Up to 10 yearsEvery year
Over 10 yearsEvery six months

Remember

  • Count age from the recorded first registration or entry into service.
  • Check your exact due date and book before the ITV expires.
  • Repair known faults; do not hide warnings.
  • Keep and carry your latest inspection report.
  • Place the V-19 sticker inside the windscreen, in the upper right-hand corner.

Exam trap: Wrong: age starts when you buy a used lorry. Right: count from its recorded first registration or entry into service.

Read the full explanation
  • For your category N2 C1 goods lorry, the periodic ITV is annual up to 10 years old and every six months once it is over 10 years old. You must apply this schedule even if you call it a light lorry; its inspection frequency does not come from the N1 schedule. [RD 920/2017, art. 6.1](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a6).
  • You must calculate its age from its recorded first registration or entry into service, not from when you buy the lorry. Check the exact date of the next inspection; a change of owner or an ordinary repair does not reset its age. [RD 920/2017, art. 6.1](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a6).
  • You can bring the inspection forward to within the 30 calendar days before expiry while retaining that expiry date as the reference for calculating the next period of validity. In other cases, validity is calculated from the favourable inspection in accordance with the article. You must plan your appointment without treating it as an extension of an expired ITV. [RD 920/2017, art. 6.5](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a6).
  • Prepare the vehicle by checking its identification, lights, visibility, wheels, brakes, steering, suspension, bodywork and emissions. You must repair known defects, rather than hide them or clear warnings to get through the test. The statutory inspection checks the vehicle's condition; it does not carry out periodic maintenance for you.
  • Keep the report and check the result, defects and next inspection date; you must carry the latest inspection report to show to officers who request it. [RD 563/2017, art. 8.1.a)](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#a8). Place the V-19 sticker in the top right-hand corner of the windscreen, on the inside. [RGV, Annex XI, V-19.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-19).

28ITV: favourable, unfavourable and negative results

A flatbed recovery truck carries a light truck secured with straps in the right-hand lane in front of a vehicle inspection station.
The key idea

Follow the driving restrictions that apply to your ITV result.

two monthsMaximum to repair minor faults
two monthsMaximum to return after failure
ITV resultFaultsDriving
*favorable* (pass)None or minor onlyAllowed; repair minor faults
*desfavorable* (fail)SeriousOnly permitted journeys for repair or regularisation and return to ITV
*negativa* (prohibition)Very seriousTransport from the station must use other means

Remember

  • Repair minor faults within two months.
  • Minor faults alone do not require another inspection to check repairs.
  • That exception ends if you return after a *desfavorable* (fail) or *negativa* (prohibition) result.
  • After *desfavorable* (fail) or *negativa* (prohibition), repair and return within two months.
  • After the allowed deadline, you need a full inspection.
  • You may choose the station for the inspection and return after repairs.

Exam trap: Wrong: drive to the workshop after a *negativa* (prohibition) result. Right: transport from the station must use means other than your lorry.

Read the full explanation
  • The result depends on the severity of the defects: with no defects or only minor ones, the ITV is favourable; a serious defect gives an unfavourable result; a very serious defect gives a negative result. [RD 920/2017, art. 9.4](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a9).
  • If minor defects are detected, you must repair them within a maximum of two months. On their own, they do not require another inspection to verify the repair, unless you must return because of an unfavourable or negative result. [RD 920/2017, art. 11.1](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a1-3).
  • With an unfavourable result, you cannot drive the lorry except for permitted journeys for repairs or to bring it into compliance and to return to an ITV station. You must rectify the defects and present it for another inspection within no more than two months of the first unfavourable result. [RD 920/2017, art. 11.2](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a1-3).
  • With a negative result, you must arrange transport from the station by means other than the vehicle itself. You must rectify the defects and return for inspection within no more than two months of the first negative result. [RD 920/2017, art. 11.3](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a1-3).
  • If you present the vehicle after the allotted deadline, you must have it undergo a full inspection. You can choose the station for the first inspection and for subsequent inspections after repairs; you are not obliged to return to the same one every time. You must comply with the result and the restrictions on driving throughout the process. [RD 920/2017, art. 11.4 and 11.8](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a1-3).

Daily walk-round check of your lorry

Follow a consistent sequence so that you do not overlook anything; finish by checking how the vehicle actually responds.

  1. Secure the vehicle in a safe area, identify hazards and look for leaks underneath it.
  2. Walk around the front, both sides and the rear: check the bodywork, guards, fastenings, lights, reflectors and exhaust.
  3. Inspect every wheel, including inner twin wheels, fixings, valves and the space between tyres; measure pressures under the specified conditions.
  4. Check the oil, coolant and other reservoirs under the temperature and waiting conditions specified for each one.
  5. Check the coupling and connections if you tow a trailer, and make sure that supports and locking devices are in their travelling position.
  6. Adjust your driving position, mirrors and visibility aids; test the horn, windscreen wipers and washers.
  7. Observe the self-check, air pressure and alarms; test the brakes safely before joining traffic.
  8. Report and rectify defects: do not set off if they compromise safety.

Checking the brake air system

Use your manufacturer's values and procedure, without applying generic pressure or leakage figures.

  1. Secure the lorry against movement and check the test conditions.
  2. Check the specified indicators and alarms when you switch on the ignition.
  3. Start the engine and check that the circuits fill normally and reach operating pressure.
  4. Carry out the specified leak test, distinguishing air used during operation from abnormal leakage.
  5. Check condensate treatment and drainage according to the equipment fitted.
  6. Check the response of the service and parking brakes in a clear area.
  7. If an alarm persists, operating pressure is not reached or there is abnormal leakage, secure the vehicle and arrange repairs.

Responding to a serious warning while driving

Give priority to controlling the lorry, stopping it, warning other road users and obtaining assistance.

  1. Identify the warning without taking your attention away from your path and reduce speed in a controlled manner.
  2. Find a safe place and move the lorry off the carriageway where feasible.
  3. Secure the vehicle and follow the manual instructions on switching off the engine and the affected system.
  4. Apply the breakdown warning and protection measures explained in “Accidents, breakdowns and first aid”.
  5. Decide where to wait safely by following the relevant section of “Accidents, breakdowns and first aid”.
  6. Request suitable assistance and report your location and the symptoms; contact the emergency services if there is immediate danger.
  7. Resume driving only when the fault is rectified and the lorry can be driven safely.

What you do after the ITV

The result determines whether you can drive and how you must arrange repairs and a reinspection.

  1. Read the report, defects and result, without relying solely on being given documentation.
  2. If the result is favourable, check the next due date and display the sticker; repair minor defects within a maximum of two months.
  3. If the result is unfavourable, restrict journeys to those permitted for rectifying defects and returning for inspection; do not use the lorry for work.
  4. If the result is negative, arrange transport from the inspection station by means other than the vehicle itself.
  5. For an unfavourable or negative result, rectify the defects and present the vehicle for inspection within the period granted, which cannot exceed two months from the first corresponding result.
  6. Keep the new report and confirm that the result allows you to resume normal road use.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module