Theory · C1 Licence - Light Truck · Module 15 of 18

Lorry mechanics and checks

You learn how the diesel engine, lubrication, cooling, fuel supply, transmission, suspension, steering and electrical systems of your C1 lorry work. You relate their components to symptoms without confusing mechanical principles with maintenance procedures.

30 min read21 sectionsReviewed Nov 3, 2026
A person looks at the exposed engine of a green light truck with its cab tilted forward, parked beside a Mediterranean road.
C1 truck mechanics and checks

1C1 lorry systems

A green light truck with an orange cargo box travels in its lane on a rural road, with the driver on the left side of the cab, holding the steering wheel and wearing a seat belt.
The key idea

Know your lorry’s systems and find their details in its manual.

Remember

  • Identify the reservoirs and controls in the manual.
  • Check your lorry’s pressures, fluids and service intervals.
  • Brakes and steering help you avoid accidents.
  • Seat belts and airbags reduce the consequences of an accident.

Exam trap: Wrong: you assume every C1 lorry has air brakes. Right: identify the systems fitted to your lorry.

Read the full explanation
  • Brakes, tyres, steering, suspension and lighting help prevent accidents; the seat belt, airbag and cab structure reduce their consequences.
  • Identify reservoirs, filler points and dashboard instruments in the manual. Pressures, capacities, fluids and service intervals depend on the lorry and how you use it; do not automatically apply values for a car. C1 lorries may have hydraulic, air or combined braking systems and electrical systems of different voltages: identify the equipment fitted.
  • Pre-use checks, preventive maintenance, fault-finding and minor repairs are covered in “C1 lorry maintenance and checks”.

2Diesel engine and operating cycle

A light truck parked beside the right-hand kerb shows a cutaway of its diesel engine with the injector spraying fuel above the piston, connected to the crankshaft by the connecting rod.
The key idea

In your diesel engine, fuel ignites because compression heats the air.

180 degreesOne piston stroke
720 degreesComplete four-stroke cycle

Remember

  • During intake, air enters the engine.
  • During compression, the air heats up.
  • Combustion and expansion produce work; exhaust removes the gases.
  • Remember: a stroke equals half a turn of the crankshaft.
  • A complete cycle needs two turns, whatever the number of cylinders.
  • If oil and coolant mix, correct the contamination before using the engine again.

Exam trap: Wrong: you confuse a stroke with a full turn. Right: a stroke is half a crankshaft turn.

Read the full explanation
  • In a diesel engine, compression heats the air and the injected diesel fuel ignites in it; ignition occurs through compression.
  • In the four-stroke cycle, you identify intake, compression, combustion-expansion and exhaust. During the intake stroke, air enters the diesel engine; during compression, its volume decreases; during expansion, work is produced; and during exhaust, the gases are expelled.
  • One stroke between dead centres equals half a revolution of the crankshaft, 180 degrees. Four strokes complete the cycle: two revolutions, 720 degrees, regardless of the number of cylinders.
  • The piston moves inside the cylinder; the connecting rod links this movement to the crankshaft, which produces rotation. The piston rings help maintain a seal and control oil. The flywheel smooths out variations in rotational speed.
  • The main journals support the crankshaft in its bearings, the crankpins carry the connecting rods and the crank webs join its sections, while the counterweights help balance it.
  • The cylinder head gasket seals the joint and keeps combustion gases and fluid passages separate. Its openings must align with those in the engine. Damage to it can allow oil and coolant to mix, but diagnosis is necessary: a hose leaking externally does not connect the two circuits. You must correct the contamination before continuing to use the engine.

3Valve timing and auxiliary belts

A mechanic uses a flashlight to inspect the engine belts of a light truck parked beside the kerb, with the bonnet open and his hands kept away from the mechanisms.
The key idea

Valve timing keeps your valves working in step with your engine.

Belt typeWhat you need to remember
Dry-running timing beltDo not oil it.
Oil-immersed timing beltUse oil compatible with its design.
Auxiliary beltMay drive the alternator, a pump or other parts.

Remember

  • Follow the manufacturer’s maintenance instructions for the timing system.
  • A chain can also wear and need maintenance.
  • Leave tension and timing adjustments to a workshop.
  • Keep your hands away from belts while the engine runs.

Exam trap: Wrong: you oil every timing belt. Right: never oil a dry-running belt; oil-immersed belts need compatible oil.

Read the full explanation
  • The valve timing system is the set of mechanisms that controls gases entering and leaving the cylinders. It must synchronise valve opening and closing with the crankshaft and piston positions.
  • The camshaft operates the valves through the mechanism provided. In a conventional four-stroke engine, it must remain synchronised with the crankshaft; loss of synchronisation can cause irregular running or serious internal damage.
  • The toothed belt transmits motion between its pulleys without slipping and maintains the valve timing. You do not lubricate a belt designed to run dry; a belt running in oil requires a lubricant compatible with that design. Follow the manufacturer's replacement schedule for the belt and associated components; the interval is not universal.
  • The valve timing system may use a toothed belt, chain or gears. You must maintain each system according to the manufacturer's instructions: a chain does not mean you can assume there is no wear, no tensioners or no need for lubrication. Adjusting tension and setting valve timing are workshop operations.
  • Auxiliary belts may drive the alternator, a pump or other components. Check for cracks, fraying and noise without bringing your hands close while the engine is running. An auxiliary belt and the timing belt have different functions, although both transmit motion.

4Fuel supply, injection and fuel

A person refuels a green light truck with its lights off beside a pump at a filling station.
The key idea

Use approved fuel and protect your lorry’s injection system.

Remember

  • Never loosen injection pipes: high-pressure diesel can pierce your skin.
  • Wrong fuel? Do not start; request assistance.
  • Before refuelling, stop the engine; switch off lights, radio and devices like mobile phones.
  • Never smoke or light a fire at a service station.
  • In severe cold, paraffin can crystallise and block the fuel filter.
  • Use approved winter diesel suitable for the expected temperatures.

Exam trap: Wrong: you dilute the wrong fuel and start. Right: avoid starting and request assistance; dilution cannot guarantee injection protection.

Read the full explanation
  • In the diesel fuel circuit, you distinguish the tank, low-pressure supply, filters, high-pressure generation and injectors. Filtration protects high-precision components; replace the filters and drain the water separator when the manufacturer specifies.
  • The injectors meter and atomise the fuel at the correct time. In a common rail system, an accumulator holds fuel at high pressure and electronic control governs injection. Do not loosen pipes to check whether diesel fuel is reaching them: a high-pressure jet can penetrate your skin.
  • The governor on a mechanical injection pump with a control rack adjusts the fuel quantity to maintain idle speed and limit maximum engine speed.
  • Use approved fuel and check the pump before refuelling. If you put in the wrong product, do not start the engine and request assistance; diluting it with the correct fuel does not guarantee protection for the injection system. After replacing a filter, priming or bleeding air requires the specific procedure.
  • To refuel, you must stop the engine and switch off the lights, radio and transmitting devices such as your mobile phone. [RGC, art. 115.3 and 4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a115).
  • At a service station, you must not smoke or light a fire: this is a fire protection measure for the site. [RD 706/2017, ITC MI-IP 04, section 10.7](https://www.boe.es/buscar/act.php?id=BOE-A-2017-9188).
  • The starting system turns the engine until combustion keeps it running; see how to use it efficiently in “Starting without wasting fuel” and “Stops and idling”, in “Preventive and efficient driving”.
  • In severe cold, the paraffins in diesel fuel can crystallise and block the filter, making starting difficult or interrupting the engine's fuel supply. Use winter diesel suitable for the expected temperatures and approved for your lorry. The Spanish specification for automotive diesel includes seasonal requirements for cold filter performance. [RD 61/2006, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2006-2779).

5Air intake, turbocharger and intercooler

A mechanic inspects the air filter, turbo and intercooler of a light truck with its cab tilted forward, stopped beside the kerb on its right.
The key idea

Your turbo supplies more air; the intercooler cools it before it enters your engine.

Remember

  • Follow the usual route: filter, turbo compressor, intercooler, engine.
  • Exhaust gases drive the turbo’s turbine.
  • Compressed air becomes denser as it cools.
  • Use the specified engine oil for a conventional turbo.
  • Do not drive without the air filter to regain power.
  • Follow your manual’s warm-up and shutdown instructions.

Exam trap: Wrong: you think the intercooler cools diesel fuel. Right: it cools compressed intake air.

Read the full explanation
  • In a conventional turbocharging layout, follow the air from the filter to the turbocharger's compressor, then to the intercooler and finally to the engine. The filter traps particles before they reach the compressor.
  • In the turbocharger, exhaust gases drive a turbine connected to the intake compressor. The compressor forces a greater mass of air into the engine.
  • The intercooler is an air-to-air or air-to-water heat exchanger that cools the compressed intake air. As the compressed air cools, its density increases, improving cylinder filling.
  • The bearings in a conventional turbocharger receive engine oil to reduce friction and carry away heat; the oil then returns to the circuit. Lack of lubrication can damage the assembly, which rotates at high speed. Warm-up and shutdown are covered in “Starting without wasting fuel”, in “Preventive and efficient driving”.
  • A blocked air filter restricts the intake and can impair combustion, performance and emissions. Maintain the filter according to its design and the working environment; do not drive without it to restore power. An abnormal whistle, loss of power or smoke also requires you to check hoses and connections.

6Lubrication circuit

A person checks the oil dipstick beside the open engine compartment of a light truck facing right, parked with the kerb along its right side in the foreground.
The key idea

Oil reduces wear and helps cool your lorry’s engine.

InstrumentWhat it shows
Dipstick or electronic indicatorOil level
Pressure gaugeOil pressure
Temperature gaugeOil temperature

Remember

  • In a wet-sump system, the sump holds the oil.
  • The pump moves oil; the filter traps solid impurities.
  • Do not exceed the maximum level: this can also cause faults.
  • Request diagnosis if the level rises without topping up or an unusual mixture appears.

Exam trap: Wrong: you use the dipstick to check pressure. Right: the dipstick shows level; the pressure gauge shows pressure.

Read the full explanation
  • Oil reduces friction and wear, removes heat and helps limit thermal expansion: it lubricates and contributes to cooling.
  • In a wet-sump system, the sump holds the oil; the pump sends it to the surfaces that need lubrication and the filter traps solid impurities. Other devices regulate the pressure.
  • The dipstick or electronic indicator shows the level; the pressure gauge shows the pressure, and the temperature gauge shows the temperature. See “C1 lorry maintenance and checks” for how to measure the oil level and top it up.
  • An oil level above the maximum can also cause faults. If emulsions appear, the level rises without you topping it up or oil consumption increases, seek a diagnosis: you may have contamination, fuel in the oil or other faults. Do not assume that adding more oil solves every oil loss.

7Lubricant pressure and selection

A driver sits in the cab of a light truck stopped in a lay-by on the right of the road, with the red oil pressure warning light illuminated on the dashboard.
The key idea

Choose approved oil and respond to your truck’s oil pressure warnings.

SAE 15W-40Example of multigrade oil
Grade in SAE 15W-40What it means
15WLow-temperature viscosity grade
40High-temperature viscosity grade

Remember

  • Compare pressure with the manufacturer’s values for that engine speed and temperature.
  • If the warning stays on after starting, stop safely and follow your manual.
  • Do the same if it comes on while driving.
  • The light going out does not mean your engine is warm.
  • Do not assume heat is the only cause of low pressure.
  • Your gearbox and differential may need different oils: use approved ones.

Exam trap: Wrong: you read oil numbers as temperatures or average them. Right: they are viscosity grades; use approved oil.

Read the full explanation
  • Compare the indicated pressure with the manufacturer's values for the engine speed and temperature.
  • When you switch on the ignition, the oil pressure warning light may come on; when you start the engine, it must go out once the correct pressure is reached. It does not indicate that the engine has already reached its operating temperature. If it stays on or comes on while driving, stop safely and follow the manual.
  • At the same engine speed and under otherwise equal conditions, very hot oil becomes less viscous and may produce lower pressure. Low pressure can also be caused by an insufficient oil level, leaks, wear, incorrect viscosity or other faults: do not keep driving on the assumption that it is only due to heat.
  • SAE 15W-40 is a multigrade oil: it meets grade 15W at low temperatures and grade 40 at high temperatures. These are viscosity grades, not temperatures, two separate oils or numbers you should average. A lower W number corresponds to better flow properties when cold; oil usually becomes less viscous as it heats up. Always use a grade and approval specified for the engine.
  • The manual gearbox and the bevel gear and differential assembly need their approved lubricants, commonly called valvulina (gear oil) in Spain. Viscosity, cold-flow properties and suitable additives matter, including extreme-pressure additives where required. Do not choose the thickest oil or one without the specification or approval stated by the manufacturer; the two assemblies may need different oils and do not automatically accept engine oil.

8Cooling: flow and regulation

A light truck travels to the right along a road, with the driver on the far side of the cab and a cutaway showing the engine, radiator, fan and coolant pipes.
The key idea

Know how coolant flows and how your engine’s temperature is controlled.

PartFunction
PumpMoves coolant.
FanMoves air through the radiator.
ThermostatControls flow to the radiator.
Temperature gaugeShows temperature.
Thermal switchSwitches a circuit when its condition is reached.

Remember

  • The radiator cools coolant during normal running too.
  • With a conventional internal bypass, coolant circulates inside the cold engine.
  • The thermostat opens flow to the radiator at the correct temperature.
  • If the pump is belt-driven, a broken belt can cause overheating.
  • Not every pump is belt-driven.
  • If temperature is excessive, stop safely and follow your manual.

Exam trap: Wrong: you think the fan moves coolant. Right: it moves air; the pump moves liquid.

Read the full explanation
  • The radiator cools the coolant coming from the engine by transferring heat to the air during normal operation, not only when overheating occurs. The pump circulates liquid between the cooling passages and the radiator when the thermostat allows that flow path.
  • The thermostat regulates flow to the radiator. In a conventional circuit with an internal bypass, when the engine is cold it initially closes the main circuit to the radiator and allows internal circulation; this helps the engine warm up. Once the correct temperature is reached, it opens the flow path to the radiator.
  • The thermostat is usually located at the cylinder head outlet leading to the radiator, depending on the design. If it sticks open, it may delay warm-up and increase fuel consumption; you must also check other causes, such as a fan running continuously.
  • The operating temperature depends on the engine. Consult the manual and the instrument panel; the coolant temperature is different from the temperature of the combustion gases.
  • The fan creates airflow through the radiator when needed, including when the vehicle is stationary. Its function is not to move the liquid: that is the pump's job.
  • If the pump is driven by the crankshaft through a belt and pulley, a loose or broken belt can cause overheating. You must also consider leaks, blockages and the thermostat; not all pumps use this drive arrangement.
  • The temperature gauge indicates temperature; the thermal switch switches a circuit when a specified condition is reached. If you have an oil temperature indicator, you must not confuse it with lubrication pressure either. If the temperature is excessive, you must stop safely and follow the manual to avoid damage.

9Coolant and circuit protection

A light truck is parked beside the kerb on its right with the bonnet open and the hot coolant cap closed, while a man waits on the pavement with his arms folded.
The key idea

Use the specified coolant and never open a hot, pressurised cooling circuit.

Remember

  • Steam or liquid from a hot, pressurised circuit can scald you.
  • Use the specified coolant type and concentration.
  • Check coolant compatibility in “C1 lorry maintenance and checks”.
  • Coolant carries heat and protects against freezing and corrosion.
  • The expansion tank allows for changes in liquid volume.

Exam trap: Wrong: you think pressure always stops coolant boiling. Right: it raises the boiling point, but cannot prevent all boiling.

Read the full explanation
  • Pressure in the circuit raises the boiling point of the same coolant. If you open it while hot, the drop in pressure can release steam and liquid and cause burns; consult the precautions for opening it in “Coolant and overheating”, in “C1 lorry maintenance and checks”.
  • Coolant carries heat and protects against freezing and corrosion; its specification, concentration and compatibility are covered in “Coolant and overheating”, in “C1 lorry maintenance and checks”.
  • The expansion tank accommodates changes in the liquid's volume as it heats up and cools down. Checking the level, checking for leaks and topping up are covered in “C1 lorry maintenance and checks”.

10Exhaust, emissions and interpreting smoke

A light truck facing left is parked beside a kerb on the far side, with orange heat waves above its exhaust and clear pavement around it.
The key idea

Smoke can warn you of faults, but diagnosis is needed to find the cause.

SmokeWhat it may mean
Persistent blue smoke with oil useOil may be burning; get a diagnosis.
Abnormal black diesel smokeToo little air or too much fuel may cause soot.
Brief white condensation in cold weatherDo not confuse it with persistent blue smoke.

Remember

  • The catalytic converter reduces harmful substances; the silencer reduces noise.
  • Never drive with an open exhaust or an incomplete, unsuitable or damaged silencer.
  • Complete carbon combustion produces carbon dioxide; exhaust can contain other gases.
  • If you have a particulate filter, follow its regeneration instructions.
  • If you use AdBlue, keep it separate from diesel; use the correct tanks.
  • During regeneration, keep combustibles away from hot exhaust outlets.

Exam trap: Wrong: you identify a faulty part from smoke alone. Right: smoke needs diagnosis, even if the engine still has power.

Read the full explanation
  • The catalytic converter transforms harmful substances in the exhaust to reduce emissions.
  • The silencer reduces exhaust noise. If it is broken, noise pollution increases. You must not drive with an unsilenced exhaust or with an incomplete, unsuitable or damaged silencer. [RGC, art. 7.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a7).
  • Complete combustion of the carbon in petrol or diesel produces carbon dioxide, CO₂. Do not confuse it with carbon monoxide: actual exhaust emissions can contain other gases and unburnt fuel, not just CO₂.
  • Persistent bluish smoke and oil consumption may indicate oil being burnt because of piston ring or valve sealing problems. You need a diagnosis; you must not confuse this with temporary white condensation when cold or with diesel consumption.
  • Abnormal black smoke from a diesel engine may indicate soot from incomplete combustion: there is too little air or too much fuel for the air available. Check the filter, air intake and injection system; it does not identify a specific faulty part or prove that the engine compensates for a lack of air by injecting more diesel.
  • On lorries fitted with them, the particulate filter traps soot and needs to regenerate; the SCR system reduces nitrogen oxides using a specific reagent. AdBlue has a separate tank from diesel: put each product only in its corresponding tank. Follow the manufacturer's regeneration and reagent warnings, without disabling the systems.
  • Regeneration can raise the exhaust temperature considerably. Follow the parking instructions and keep combustible materials away from hot exhaust outlets. An emissions warning requires diagnosis even if the engine still delivers power; smoke alone does not tell you which part to replace.

11Transmission to the wheels

A light truck follows its lane around a bend, with a transparent cutaway showing the engine, gearbox, propeller shaft and differential connected to the rear wheels by half shafts.
The key idea

Your transmission carries engine rotation to your truck’s driven wheels.

Remember

  • In conventional rear-wheel drive, the propeller shaft connects separate assemblies.
  • Half-shafts carry rotation from the differential to your driven wheels.
  • Shaft joints allow angle changes; sliding parts allow length changes.
  • On bends, your differential lets driven wheels on one axle turn at different speeds.
  • Request inspection for vibrations, knocks when moving off or oil leaks.
  • Never go under your truck without suitable supports.

Exam trap: Wrong: you lock the differential unnecessarily on a high-grip surface. Right: if fitted, use it only as your manual directs; misuse can damage the transmission.

Read the full explanation
  • In a conventional rear-wheel-drive lorry, you can trace the path through the engine, clutch, gearbox, propeller shaft, final drive, differential and half-shafts. Each component has a different function; the propeller shaft connects separate assemblies and the half-shafts carry rotation from the differential to the driven wheels.
  • The propeller shaft joints allow rotation to be transmitted as the angles change with suspension movement; sliding components compensate for changes in length. Vibrations, knocks when moving off or lubricant leaks require inspection. Do not go underneath the lorry without suitable supports.
  • The final drive adapts rotational speed and torque for the wheels. The differential allows the driven wheels on the same axle to turn at different speeds on a bend. If a differential lock is fitted, use it only as instructed in the manual: locking it unnecessarily on a surface with good grip can damage the transmission.

12Clutch: engagement and wear

A light truck driver drives with both hands on the steering wheel and the left foot resting on the floor, separated from the clutch pedal, which remains untouched.
The key idea

Your clutch connects or disconnects the engine from the gearbox input.

Conventional clutch pedalClutch state
ReleasedEngaged: engine connected to gearbox input.
PressedDisengaged: engine separated from gearbox input.

Remember

  • To drive the wheels, you need a gear engaged and an operational transmission.
  • A clutch that slips while transmitting force produces heat.
  • Hydraulic control transmits pedal pressure through fluid.
  • If engine speed rises without matching acceleration, the clutch may slip.
  • With pedal fully pressed, a hard-to-engage gear may mean the clutch does not disengage.
  • With these symptoms, request diagnosis of the clutch and its control system.

Exam trap: Wrong: you think releasing the clutch drives the wheels in neutral. Right: you need a gear engaged and an operational transmission.

Read the full explanation
  • The clutch connects or disconnects the engine from the gearbox input. In a friction clutch, the pressure mechanism presses the clutch disc against the flywheel to transmit rotation.
  • With a conventional clutch, releasing the pedal means the clutch is engaged and pressing it means the clutch is disengaged. To drive the wheels, you also need a gear engaged and the transmission to be operational; in neutral, engaging the clutch is not enough.
  • Friction between the disc and the flywheel allows torque to be transmitted; if they slip while transmitting load, some of the energy turns into heat. Clutch use is covered in “Using the clutch and automatic systems correctly”, in “Preventive and efficient driving”.
  • The clutch control system may be hydraulic: it transmits pedal pressure through fluid to an actuator. Its circuit may share a reservoir with the brakes, depending on the design.
  • In a clutch disc with helical torsional damper springs, these springs smooth out variations in torsion and the transmission of torque to the gearbox.
  • If engine speed rises and the lorry does not accelerate proportionally, the clutch may be slipping. If it is difficult to engage a gear with the pedal fully pressed, the clutch may not be disengaging properly: the disc continues to drag the gearbox input round. Both symptoms require diagnosis of the assembly and its control system.

13Gearbox and gear selection

A driver wearing a fastened seat belt selects a gear in the cab of a light truck while travelling in the right lane of an uphill road.
The key idea

Choose a gear that suits your lorry’s speed and required driving force.

Gearbox typeWhat to remember
Non-synchronisedMay need double-declutching.
Automated manualActuators operate a mechanical clutch without a clutch pedal; electronics select gears.

Remember

  • A low gear multiplies torque more, giving you more driving force.
  • At the same engine speed, a low gear gives a lower output speed.
  • Neutral is not a brake.
  • Synchronisers match speeds before engagement.
  • If a gear grinds, do not force the lever: there may be different causes.
  • Changing down too far can cause excessive engine speed and damage the transmission.

Exam trap: Wrong: you confuse double-declutching with a dual-clutch transmission. Right: one is a technique; the other is a transmission type.

Read the full explanation
  • The gearbox allows you to adapt speed and tractive effort to your lorry's needs. A low gear provides greater torque multiplication at the cost of a lower output speed for the same engine speed. Neutral interrupts torque transmission through an engaged gear; it does not act as a brake.
  • Synchronisers match speeds before engagement; a non-synchromesh gearbox may require double-declutching, which you must not confuse with a dual-clutch transmission.
  • If a gear grinds, the synchroniser or clutch disengagement may be faulty. Do not force the gear lever or attribute every noise to a single component.
  • An automated manual gearbox uses a mechanical clutch operated by actuators, without a clutch pedal; electronic control also governs gear selection. It differs from an automatic gearbox with a torque converter and from a dual-clutch transmission. Identify its positions, warnings and limitations before manoeuvring. [Regulation (EU) 2017/2400, Annex VI, section 2, points 19 and 20](https://www.boe.es/doue/2017/349/L00001-00247.pdf).
  • Changing down increases engine speed at the same lorry speed; selecting too low a gear can cause engine overspeed and damaging stresses in the transmission. See gear selection and skipping gears in “Choosing high gears without straining the engine”, in “Preventive and efficient driving”.

14Braking systems

A light truck with its driver seated is stationary beside a kerb on its right side, in the background of the image.
The key idea

Use your brakes to reduce speed or hold your truck stationary.

Remember

  • Recognise the service, secondary and parking brake systems.
  • Study brakes and retarders in “Brakes and retarders on light lorries”.
  • Find checks in “C1 lorry maintenance and checks”.

Exam trap: Wrong: you only associate brakes with slowing down. Right: they also hold your truck stationary.

Read the full explanation
  • The brakes slow or immobilise your lorry through the service, secondary and parking braking systems; their operation and retarders are covered in “Brakes and retarders on light lorries”, and their checks in “C1 lorry maintenance and checks”.

15Suspension, leaf springs and levelling

A light truck with secured cargo travels along a road, showing the longitudinal leaf spring centred and clamped to the rear axle, its chassis attachments and the shock absorber.
The key idea

Your suspension absorbs bumps and helps you control your truck.

Part or systemFunction you need to recognise
Leaf springs, coil springs or air bellowsProvide spring action.
Shock absorbersDamp the movement of the spring elements.
Height-controlled air suspensionLevels your truck as the load changes, within its limits.

Remember

  • Your suspension sits between the axles and the body or chassis.
  • Ineffective shock absorbers reduce your stability and grip.
  • Use the specified heights for loading, unloading and driving.
  • Automatic levelling does not let you exceed the maximum authorised mass.
  • Never work under the chassis relying only on inflated air bellows.

Exam trap: Wrong: you expect constant height despite overload or faults. Right: height-controlled air suspension only levels within its limits.

Read the full explanation
  • The suspension is the assembly between the wheel axles and the body or chassis that absorbs road irregularities and promotes comfort and control.
  • Leaf springs, coil springs and air bellows are elastic components; shock absorbers damp their oscillations and help keep the tyres in contact with the ground. If they lose effectiveness, stability and grip deteriorate, and wear on joints and mountings may increase.
  • In air suspension with height control, air adjustment automatically levels the body or chassis as the load changes within its limits. It does not guarantee a constant height when overloaded or faulty, nor does it allow you to exceed the MMA (maximum authorised mass); observe the specified height settings for loading, unloading and driving.
  • Air suspension can change height during work on the vehicle. Do not work beneath the chassis relying solely on inflated air bellows; inspections are covered in “C1 lorry maintenance and checks”.

16Steering, alignment and balancing

A mechanic inspects the front right wheel of a light truck parked beside the kerb while the driver remains at the steering wheel on the left side of the cab.
The key idea

Steering directs your wheels; request inspection for vibration, stiffness or persistent pulling.

OperationWhat you correct
BalancingMass distribution of the wheel and tyre assembly.
AlignmentSteering and suspension geometry.

Remember

  • Hydraulic assistance uses a pump and fluid; purely electric assistance uses an electric motor.
  • Purely electric assistance has no hydraulic reservoir.
  • Power steering reduces the effort you need to turn the wheels.
  • Free play can delay the wheels’ response when you turn the steering wheel.
  • Find fault symptoms in “C1 lorry maintenance and checks”.
  • After a kerb impact, request inspection even if it seems minor.

Exam trap: Wrong: you confuse alignment and balancing. Right: alignment corrects geometry; balancing corrects wheel-and-tyre mass distribution.

Read the full explanation
  • The steering transmits movement from the steering wheel to the steered wheels. Hydraulic assistance uses a pump and fluid; purely electric assistance uses an electric motor and has no hydraulic reservoir.
  • Balancing corrects the mass distribution of the wheel and tyre assembly; alignment corrects the steering and suspension geometry. These are different operations: a wheel can be balanced and have an incorrect alignment angle.
  • Symptoms of vibration, pulling to one side and uneven resistance are covered in “Steering and suspension: signs of faults”, in “C1 lorry maintenance and checks”.
  • Castor and steering axis inclination help the wheels return to the straight-ahead position; the worm gear or rack-and-pinion mechanism transmits the steering wheel's rotation.
  • Power steering reduces the effort needed to turn the wheels by using an auxiliary power source; the degree of assistance can vary according to the vehicle's design and operating conditions.
  • Free play is looseness between steering components and can delay the wheels' response to turning the steering wheel. An impact against a kerb can affect the tyre, wheel rim or steering even if it appears minor externally; arrange an inspection if this happens.

17Tyre construction

A light truck travels to the right on a wet road while its tyre grooves displace water where the tyres contact the asphalt.
The key idea

Recognise your tyres’ parts and how their structure supports the load.

Tyre constructionHow its layers run
RadialCords cross the direction of travel; a belt runs around the tyre.
Cross-plyLayers cross diagonally.

Remember

  • The tread touches the road and helps maintain grip.
  • Its grooves help disperse water.
  • The casing supports the load of the inflated tyre.
  • The sidewall is between the tread and the rim.
  • Low pressure increases tyre flexing and heat.
  • TUBELESS means the tyre has no inner tube.

Exam trap: Wrong: you think TUBELESS means there is an inner tube. Right: it is designed without one; the bead seals against the rim.

Read the full explanation
  • The tread contacts the ground, protects the carcass and contributes to grip; its grooves help disperse water. [UN Regulation 54, section 2.8](https://www.boe.es/buscar/doc.php?id=DOUE-L-2008-81371).
  • The carcass forms the load-bearing structure that supports the load on the inflated tyre; the sidewall is the side area between the tread and the rim. [UN Regulation 54, sections 2.7 and 2.9](https://www.boe.es/buscar/doc.php?id=DOUE-L-2008-81371).
  • In radial construction, the ply cords run transversely to the direction of rolling and a circumferential belt stabilises the carcass; in cross-ply construction, the plies cross diagonally. [UN Regulation 54, section 2.3](https://www.boe.es/buscar/doc.php?id=DOUE-L-2008-81371).
  • Insufficient pressure increases tyre flexing and heat generation; see how to check it and its effects on wear in “C1 lorry maintenance and checks”, section “Cold tyre pressures and wear”.
  • TUBELESS indicates a tyre designed for use without an inner tube. [UN Regulation 54, section 3.1.7](https://www.boe.es/buscar/doc.php?id=DOUE-L-2008-81371). The bead seats against the rim and forms an airtight seal; a puncture usually causes a slower loss of pressure than in a tyre with an inner tube. [DGT, Manual II, topic 8, section 2.2.2: tubeless tyres](https://sede.dgt.gob.es/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2025/Manual-II-Cuestiones-de-Seguridad-Vial-2025.pdf).
  • See how to check the other markings in “C1 lorry maintenance and checks”, section “Read the tyre markings”, and how to inspect the tread in “Tyres: tread and damage”.

18Electrics, alternator and battery

A seat-belted driver observes the illuminated charging warning light on the dashboard of a light truck stopped beside the right-hand kerb, with its cargo box visible in the mirror.
The key idea

Know how your truck stores electricity and generates it while the engine runs.

PartFunction you need to distinguish
BatteryStores energy for starting and electrical equipment.
AlternatorGenerates electricity while your engine runs.
RegulatorControls charging.

Remember

  • When you switch on the ignition, the charging light comes on during self-check.
  • It normally goes out after starting.
  • If it stays on or appears while driving, the charging system may be faulty.
  • Do not disconnect the battery while the engine runs to test the alternator.
  • Distinguish volts for voltage, amperes for current and ampere-hours for capacity.
  • Open and sealed batteries have different needs.

Exam trap: Wrong: you assume the battery is fully charged when the charging light goes out. Right: the light going out does not confirm this.

Read the full explanation
  • The battery stores energy for starting and electrical equipment; the alternator generates electricity while the engine is running, and the regulator controls charging. Distinguish between voltage in volts, current in amperes and capacity in ampere-hours.
  • The charging warning light comes on during the check when you switch on the ignition and normally goes out after you start the engine. If it stays on or comes on while driving, there may be a fault in the alternator, regulator or circuit; the light going out does not confirm that the battery is fully charged. Do not disconnect the battery with the engine running to test the alternator.
  • A lead-acid battery contains an electrolyte of sulphuric acid and water; open and sealed designs have different requirements. Series and parallel connections and maintenance operations are covered in “C1 lorry maintenance and checks”.

19Diesel engine starting system

A driver watches the illuminated glow-plug indicator on the dashboard of a light truck stopped beside the kerb on its right-hand side.
The key idea

Follow your manual when starting; a click alone cannot identify the fault.

Remember

  • The starter motor turns the engine using battery power.
  • Its pinion engages the flywheel ring gear, then disengages when the engine runs.
  • The relay or solenoid connects the high current needed for starting.
  • Glow plugs help ignition, especially when cold; follow the dashboard indication.
  • Use short attempts and observe the manufacturer’s pauses.
  • Release the control when the engine starts.

Exam trap: Wrong: a click proves the starter motor is faulty. Right: the battery, connections, solenoid or starter may be at fault; the sound alone cannot tell you.

Read the full explanation
  • The starter motor converts electrical energy from the battery into rotation of the internal combustion engine. Its pinion engages with the flywheel's ring gear and disengages when the engine runs on its own.
  • The starter relay or solenoid switches on the high current needed by the electric motor; in the usual design, it also moves the pinion into engagement with the ring gear.
  • Glow plugs help create the conditions needed for ignition in a diesel engine, especially when cold. Follow the preheating indication on the dashboard; they do not produce a spark for each combustion event.
  • A click without the engine turning over may indicate a discharged battery, poor connections or a fault in the solenoid or starter motor. The sound alone does not identify a faulty component.
  • Operate the starter in short attempts and observe the manufacturer's specified pauses to avoid overheating it and discharging the battery. Release the starter control when the engine starts; the jump-starting procedure is covered in “C1 lorry maintenance and checks”.

20Electrical protection and dashboard information

A driver switches on the ignition in the cab of a light truck stopped beside the right kerb, with the coolant, oil and battery indicators illuminated and a handbook open to their pictograms.
The key idea

Understand your dashboard warnings and remember that fuses break circuits when current is excessive.

Remember

  • A fuse melts and breaks the circuit when current is excessive.
  • Its operation depends on current and time.
  • It does not transform current or prevent a fault from occurring.
  • It does not protect against every overvoltage.
  • Use the manual to understand each dashboard symbol and message.
  • When you switch on the ignition, self-check helps you detect faulty indicators.

Exam trap: Wrong: you think a fuse continuously reduces current. Right: it melts and breaks the circuit according to its current rating and operating time.

Read the full explanation
  • A fuse melts in response to overcurrent according to its current rating and operating time, breaking the circuit. It protects against the consequences of overloads and short circuits; it does not transform current, continuously reduce it or protect against every overvoltage. Nor does it prevent a fault from occurring.
  • The dashboard receives information from sensors and electronic control units. Interpret each symbol and message using the lorry's manual; coolant temperature, oil pressure and electrical charge describe different quantities.
  • The self-check allows you to detect faults in the indicators when you switch on the ignition. Actions to take in response to warnings, fuse replacement and jump-starting are covered in “C1 lorry maintenance and checks”.

21Visibility systems

A light truck travels in its lane with a headlight beam directed towards the road surface while a car approaches in the opposite lane.
The key idea

Know how your headlamps, glass and windscreen wipers help you see.

Glass typeWhat you need to remember if it breaks
LaminatedIts middle layer holds many fragments.
ToughenedBreaks into small pieces.

Remember

  • In a conventional headlamp, the reflector and optics direct the light.
  • Adjusting your headlamps aims the light without dazzling others.
  • After an impact, neither glass type guarantees that you can still see clearly.
  • Your washer sprays fluid; your wiper blades clear water and dirt.

Exam trap: Wrong: you confuse washers and wipers. Right: washers spray fluid; wipers clear water and dirt with their blades.

Read the full explanation
  • In a conventional headlamp, the reflector and optics direct the beam; headlamp adjustment sets its direction to illuminate the road without dazzling others.
  • Laminated glass retains many fragments through its interlayer when it cracks; toughened glass breaks into small pieces. Neither guarantees that visibility is maintained after an impact.
  • The windscreen washer pumps fluid onto the glass, and the windscreen wiper removes water and dirt with its blades. Controls, fluids and replacements are covered in “C1 lorry maintenance and checks”.

From fuel to movement

Follow the energy conversions in a diesel lorry.

  1. The electric starting system begins turning the engine.
  2. Compression heats the air; injection supplies the diesel fuel, which ignites.
  3. Pistons, connecting rods and the crankshaft convert expansion into rotation.
  4. The clutch, gearbox, propeller shaft and differential transmit and adapt torque to the driven wheels.

Regulating engine temperature

Relate each component to the heat carried by the coolant.

  1. The pump circulates coolant through the engine.
  2. The thermostat regulates flow to the radiator according to temperature.
  3. The radiator transfers heat to the air; the fan helps this exchange.
  4. The expansion tank accommodates changes in the liquid's volume.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1When approaching a foreseeable stop, if conditions allow safe deceleration, what helps save fuel in a combustion-engine vehicle?
2In a lorry’s friction clutch with a manual gearbox, which component is pressed against the flywheel to transmit engine rotation to the gearbox input?
3Should you periodically check the level of the windscreen washer fluid?
4Stopping distance when braking for a hazard is the sum of...

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module