Theory · C1 Licence - Light Truck · Module 14 of 18

Brakes and retarders on light lorries

You learn to use the brakes and retarders fitted to your C1 lorry, interpret circuits and warnings, and prevent loss of braking efficiency on descents. You learn about accelerator control and the braking rules for light trailers, together with the pneumatic connections used in heavy-vehicle systems.

32 min read25 sectionsReviewed Nov 3, 2026
A green light truck travels downhill to the right in its lane on a rural road with hills and cypress trees.
Controlling the truck on descents

1Three braking functions

A light box truck is stopped beside the right-hand kerb of a road, with the driver on the left side of the cab and the passenger seat empty.
The key idea

Use each braking function for its own purpose.

3,500 kgMMA (maximum authorised mass): over this limit
7,500 kgMaximum MMA with C1
FunctionWhat you use it for
ServiceControl speed and stop
SecondaryStop if the service brake fails
ParkingKeep your lorry still

Remember

  • Use the service brake to slow down and stop.
  • Use secondary braking to stop if the service brake fails.
  • Use the parking brake to keep your lorry still.
  • Use only equipment fitted to your lorry.

Exam trap: Wrong: all disc brakes use hydraulic pressure. Right: they can also use air pressure.

Read the full explanation
  • You use the service brake to control the lorry's speed and stop it; you use the secondary brake to stop it if the service brake fails; you use the parking brake to keep it stationary. These are three required functions, even if they share components. [RGV, art. 12.8 and Annex VIII, sections 1.2.1 to 1.2.3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • In the braking equipment, you can identify the control, the transmission of force and the wheel brake. The pedal gives the command; pipes and valves transmit and regulate it; pads or shoes produce friction. [RGV, Annex VIII, section 1.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anviii).
  • You may find hydraulic, pneumatic or combined actuation on a C1 lorry. These terms describe how force is transmitted or generated; disc and drum describe the friction mechanism. A disc brake can have pneumatic actuation.
  • You must apply this knowledge to the goods lorry with an MMA (maximum authorised mass) of more than 3,500 kg and up to 7,500 kg that you can drive with C1. The licence category does not determine whether your lorry has a compressor, spring brake actuators or a particular type of retarder: learn how they work and use only the equipment fitted. [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).

2Service brake and braking control

A light truck with its brake lights illuminated approaches two cars in a traffic queue, leaving space ahead on a two-way road.
The key idea

Adapt your pedal force to the situation.

Your lorry at the same speedHeat your brakes must remove
LadenMore than when unladen
UnladenLess than when laden

Remember

  • Brake progressively in normal situations.
  • In an emergency, brake firmly.
  • Adapt your braking to traffic, load and road surface.
  • Look ahead for slowing traffic.
  • Check behind without delaying urgent braking.
  • Do not rest your foot on the brake pedal.

Exam trap: Wrong: you always brake gently, even in emergencies. Right: you use the available braking capacity firmly.

Read the full explanation
  • You must normally use the pedal to slow down or stop. It allows you to vary the braking force: normal braking must be progressive and suit the traffic, load and road surface. In an emergency, you need to use the available braking capacity decisively; progressive braking does not mean avoiding hard braking when it is needed.
  • The energy of motion is converted mainly into heat in the friction brakes. A loaded lorry requires more energy to be dissipated than the same lorry unladen at the same speed; the loss of effectiveness due to heat is explained in «Brake fade and long descents».
  • You must anticipate traffic queues and check the traffic behind you when you can do so without delaying urgent braking. Distances and safety gaps are covered in the «Speed and safe following distances» module.
  • You must not habitually rest your foot on the brake pedal. You can cause unnecessary brake application, heat and wear, as well as confuse drivers behind you. When you need to slow down, use the control deliberately and check that the response matches the braking effort you request.

3Secondary braking

A belted driver seated on the left side of a light truck keeps one hand on the steering wheel and the other on a dashboard control while travelling in the right lane of a rural road.
The key idea

Use secondary braking to stop if your service brake fails.

Remember

  • Know your lorry’s emergency brake control.
  • Control the force to avoid suddenly locking the wheels.
  • You may retain reduced braking if part of the system fails.
  • Use this remaining braking to stop safely.
  • Do not confuse ABS with a secondary braking circuit.

Exam trap: Wrong: your retarder provides complete secondary braking. Right: it does not automatically perform every function.

Read the full explanation
  • Emergency braking, also called secondary braking, serves to stop the vehicle if the service brake fails. It must allow you to vary the braking force; it does not mean suddenly locking the wheels. [RGV, Annex VIII, section 1.2.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anviii).
  • You must know the specific emergency control on your lorry. Depending on the design, this function may use a working part of the service brake circuit or a control associated with the parking brake. Do not assume that every pull control, button or lever applies the same force or that you can operate it abruptly while driving.
  • If part of the system fails, you may retain reduced braking capacity thanks to the separation of the circuits. This reserve is intended to allow you to stop safely.
  • A retarder helps you control speed, especially downhill; it does not automatically perform all the functions of secondary braking. Nor is ABS a secondary braking circuit: it controls wheel locking within the available braking system.

4Parking and securing the lorry

A light truck parked uphill beside the kerb is secured with wheel chocks behind its wheels while the driver watches it from the pavement with the key in his hand.
The key idea

Secure your lorry before leaving your seat.

Remember

  • Apply your mechanically held parking brake to keep your lorry still.
  • Do not rely on keeping the pedal pressed.
  • On slopes, follow “Secure your lorry on a slope”.
  • Find it in “Manoeuvres with your lorry”.
  • Check that your lorry stays still before leaving the cab.
  • Do not use the parking brake to control downhill speed.

Exam trap: Wrong: you rely only on the warning lamp. Right: you check that your lorry stays still.

Read the full explanation
  • You must apply the parking brake to keep the lorry stationary, even when you are not in the cab. Its holding force must be maintained mechanically; you cannot rely on keeping the pedal pressed or on retaining service brake air in the chambers indefinitely. [RGV, Annex VIII, section 1.2.3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anviii).
  • To secure the lorry on a slope, follow the procedure in the «Secure your lorry on a slope» section of the «Manoeuvres with your lorry» module. [RGC, art. 92.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).
  • You must check that the lorry is effectively secured before leaving the cab. The warning light indicates the state detected by the system, but does not replace this check. Do not use the parking brake as your normal means of controlling speed downhill or as a substitute for the service brake while driving.

5Discs, drums and grip

A light truck travels to the right in its lane on a wet road in the rain, with puddles and water splashing beside its tyres.
The key idea

Distinguish your brake mechanism from your tyres’ grip.

MechanismParts that rub
DrumShoes against the inside of the drum
DiscPads against the disc faces

Remember

  • Take extra care on ice or wet roads.
  • Your wheels may lock if braking force exceeds available grip.
  • Do not assume ventilated discs cannot overheat.
  • Arrange inspection for noise, vibration or uneven wear.
  • Do not improvise adjustments to hide faults.

Exam trap: Wrong: new brakes guarantee grip. Right: grip also depends on the road surface.

Read the full explanation
  • In a drum brake, the drum rotates with the wheel and the shoes move towards its inner surface. The linings provide the friction surface. The backplate supports the shoes.
  • A disc brake consists of a disc, a caliper and pads. The disc rotates with the wheel and the pads press against its faces to resist movement. Ventilation helps dissipate heat, but does not make overheating impossible or remove the need to check for wear.
  • Brake capacity and tyre grip are different factors. If you request more braking force than the contact with the road can transmit, slipping occurs and there is a risk of wheel locking. On ice or a wet road surface, you need greater caution even if the components are new and the air pressure in the braking system is correct.
  • You must recognise vibrations, noises and uneven wear as signs that an inspection is needed. Technical inspection of the mechanism and maintenance are tasks for trained personnel; do not improvise adjustments to conceal the symptom.

6The compressed air path

A light truck facing right shows its pneumatic braking circuit beneath the body and the driver with the steering wheel on the left side, at the far side of the cab, beside the empty passenger seat.
The key idea

Pressing the pedal controls the air pressure that applies your brakes.

SystemWhat you need to know about air
PneumaticAir is the intended working medium
HydraulicAn air pocket can indicate a fault

Remember

  • The compressor draws air in; treatment reduces moisture and dirt.
  • Reservoirs store air; valves send pressure to the chambers.
  • You need enough stored air for normal braking.
  • Respect the protection separating your circuits.
  • Check the manufacturer’s instructions for the exact layout.

Exam trap: Wrong: air always means a fault. Right: distinguish air brakes from hydraulic brakes.

Read the full explanation
  • The functional path of the air is as follows: the compressor draws in air, treatment reduces impurities and moisture, the reservoirs store energy and the valves deliver pressure to the chambers when you request braking. This is an outline to help you understand the functions; the location and exact order of some assemblies depend on the manufacturer.
  • The actuating force comes from air pressure acting on a surface in the actuator. When you press the pedal, you control and regulate this pressure; you do not generate all the force needed to stop the lorry with your leg. Without a sufficient reserve, the system does not have its normal operating conditions.
  • In a pneumatic circuit, air is the intended working medium; in a hydraulic circuit, an air pocket can be a fault. This is why «removing air» and «draining or bleeding» mean different things depending on whether you are talking about brake fluid or water condensed in an air reservoir.
  • Other equipment, such as air suspension, may share the air supply. You must respect the separation and protection of its circuits, which help preserve priority functions if a leak occurs.

7Compressor and pressure regulation

A mechanic checks the pneumatic circuit pressure of a light truck parked beside the kerb using a pressure gauge connected by a hose to a test port.
The key idea

Check your manual to know when you have enough pressure.

Remember

  • The compressor produces compressed air; reservoirs store it.
  • Check the required pressure before moving off.
  • Do not increase the governor settings.
  • Investigate if your compressor runs almost constantly.
  • Do not move off if pressure takes too long to recover.

Exam trap: Wrong: use another lorry’s pressure values. Right: follow your own lorry’s manual.

Read the full explanation
  • The compressor produces compressed air and replenishes the air used. In a conventional system, the lorry's engine drives it. The reservoirs store the air it produces; they are not pumps and do not generate new pressure themselves when the reserve runs out.
  • You must consult the lorry's manual for the normal pressure range and the conditions for moving off. The values depend on the equipment; an indicative pressure for another vehicle does not serve as a threshold for moving off.
  • The regulator controls air production or unloading to maintain the specified range; the safety protection limits abnormal overpressure. You must not increase its settings in the belief that this provides more braking force: incorrect pressure can damage components without improving grip.
  • If the compressor runs almost constantly or the pressure takes an abnormally long time to recover, you must investigate the cause. There may be a leak or a problem with air production or regulation. Do not compensate by revving the engine indefinitely or start your journey assuming that the pressure recovers as you drive.

8Dryer, moisture and drainage

A worker wearing safety glasses operates the drain of an air reservoir from beside a parked light truck and collects the water in a tray.
The key idea

Control air moisture by following your lorry’s instructions.

Remember

  • The dryer reduces moisture in the air.
  • Collected water can cause corrosion and freeze.
  • Maintain the dryer on the manufacturer’s schedule.
  • Drain reservoirs when their design requires it.
  • If water keeps collecting, arrange an air treatment system check.
  • Do not add oil, coolant or alcohol yourself.

Exam trap: Wrong: every lorry needs the same drainage routine. Right: follow the manufacturer’s procedure and maintenance schedule.

Read the full explanation
  • The air drawn in contains moisture, which can condense as the air is compressed and cooled. Accumulated water encourages corrosion and, in sufficiently cold conditions, can freeze and affect valves or pipes. The dryer reduces this moisture.
  • You must maintain the dryer and its desiccant element according to the manufacturer's schedule. Repeated water accumulation in the reservoirs may require the air treatment system to be checked.
  • Where the design requires it, you must drain the air reservoirs using the devices provided to remove condensate. The procedure may be automatic or manual; do not apply a single drainage frequency to all vehicles.
  • You must not add engine coolant, oil or alcohol indiscriminately to the pipes. Some specific systems use antifreeze protection specified by their manufacturer, but this requires a compatible product and device. You must avoid contaminating the circuit and observe the precautions for any work involving pressurised air.

9Reservoirs and circuit protection

A driver looks at the two pressure gauges of a light truck stopped beside the right-hand kerb, with one in the low-pressure zone, the other in the normal zone and a warning light illuminated.
The key idea

Act on any pressure loss, even if another circuit seems normal.

ValveFunction you must distinguish
Non-returnRestricts air flowing backwards
Multi-circuit protectionLimits leaks and preserves pressure in unaffected parts

Remember

  • Your reservoirs hold a limited air reserve.
  • You cannot keep braking indefinitely with that reserve.
  • Circuit protection limits the effects of a leak.
  • Heed warnings from any circuit losing pressure.

Exam trap: Wrong: one normal gauge proves everything works. Right: check each circuit.

Read the full explanation
  • Both «depósito de aire» and «calderín» mean an air reservoir: the vessel that holds the compressed-air reserve. Its pressure allows brake applications without each application depending on the compressor's immediate output. The number of applications available depends on the equipment, pressure and losses: the reserve is not inexhaustible.
  • A multi-circuit protection valve limits the consequences of a leak and helps maintain pressure in the unaffected parts.
  • The non-return valve allows air to flow in the intended direction and restricts reverse flow.
  • If a circuit loses pressure, you must heed its warning even if another gauge still shows a normal reading. A correct reading in one part does not confirm the condition of the whole system.

10Pedal, valves and chambers

A light truck travels to the right with a transparent cutaway showing the driver on the left side pressing the pedal and the pneumatic circuit connected to the rear wheel brake mechanism.
The key idea

Use the pedal to send pressure to the chambers that apply your brakes.

ValveFunction
Relay, if fittedUses nearby stored air for a quick response
Quick-releaseHelps air escape locally

Remember

  • The pedal valve controls the pressure you request.
  • Chambers turn pressure into force and movement.
  • When you release service braking, air leaves the chambers to release the brakes.
  • You may hear normal air discharge when releasing certain controls.
  • Suspect a leak with continuous escaping air and an abnormal pressure drop.

Exam trap: Wrong: the quick-release valve limits maximum pressure. Right: it helps air leave the chambers.

Read the full explanation
  • When you press the pedal, a control valve regulates the requested pressure. Relay valves, where fitted, allow air stored near the actuators to be used for a rapid response.
  • Brake chambers or cylinders are actuators: they convert pressure into movement and force on the wheel brake mechanism. Depending on the design, they operate through diaphragms, pistons and mechanical linkage components.
  • When you stop requesting service braking, air is exhausted from the chambers to release the mechanism. The quick-release valve helps exhaust this air locally.
  • You may hear a normal release of air when you release certain controls or during dryer regeneration. A continuous escape of air accompanied by an abnormal pressure drop indicates a possible leak.

11Pressure gauges and reserve warnings

A light truck driver travels in the right lane beside a lay-by, with two pressure gauges at the low end of their scales and an orange warning illuminated on the dashboard.
The key idea

Watch the pressure and stop safely if your air reserve is low.

Remember

  • Your gauges show pressure, not wear or temperature.
  • Check the units and normal values in your manual.
  • Check that your low-pressure warning works.
  • Watch for abnormal differences between circuits.
  • If your reserve is too low, prepare to stop safely.
  • Do not wait until you run out of air.

Exam trap: Wrong: you wait for the spring brakes to apply. Right: you stop safely before exhausting your reserve.

Read the full explanation
  • The dashboard pressure gauges show the pressure in the circuit or reserve they monitor; they do not directly indicate brake pad wear, the amount of hydraulic fluid or brake disc temperature. Identify the units and normal range in the manual before interpreting a reading.
  • You must check the low-pressure warning and its self-test function as specified for the vehicle. It may combine visual and audible warnings. Do not memorise a single activation value for all lorries: distinguish between normal pressure, minimum operating pressure and the warning threshold, which are defined for the equipment concerned.
  • If an insufficient-reserve warning appears while you are driving, you must prepare to stop safely using the braking capacity available. Do not wait until the system runs out of air or the spring brakes apply. The advance warning allows you to act before the conditions necessary for braking are lost.
  • You must monitor pressure changes and abnormal differences between circuits. The leak-tightness check is explained in «Leaks and loss of effectiveness».

12Spring brake actuators

A light truck facing right is parked beside the foreground kerb, with a chocked wheel and a cutaway of the brake actuator showing its spring and pushrod.
The key idea

In a spring parking brake, air releases the brake.

ChamberEffect of air you must distinguish
ServiceApplies the brake
Spring parking brakeCompresses the spring to release the brake

Remember

  • The spring applies the brake when air pressure cannot keep it compressed.
  • A sufficient pressure loss can activate the spring.
  • Do not wait for that activation before stopping.
  • Do not dismantle spring chambers: they can cause serious injury.
  • Manual release needs a specific procedure and securing measures.
  • Releasing the spring does not repair the fault or let you resume transport.

Exam trap: Wrong: air applies the spring parking brake. Right: air holds the spring compressed and releases the brake.

Read the full explanation
  • In a spring-operated parking brake, the spring applies the brake and sufficient air pressure keeps the spring compressed to release the brake. If the pressure in the spring compression chamber is insufficient, the spring exerts force on the brake. In the service chamber, air pressure applies the brake. [UN Regulation No. 13, Annex 8, paragraphs 1.1, 1.2 and 2.5](https://www.boe.es/buscar/doc.php?id=DOUE-L-2026-80539).
  • Combination chambers bring together the service brake and spring brake functions in one assembly. The equipment's protective devices prevent harmful combinations of forces according to its design.
  • If the pressure holding the spring compressed falls sufficiently, the spring can apply the brake. You must avoid reaching this situation while driving: automatic application due to air loss does not guarantee a smooth stop or a safe path. A leak requires action before the remaining reserve is used up.
  • You must not dismantle a spring brake chamber: it contains stored mechanical energy capable of causing serious injury. Release systems for recovery or towing require specific procedures and securing measures. Manually releasing the spring removes its holding action; it does not repair the fault or allow you to resume the transport operation.

13Checks before moving off

A driver seated on the left side of the cab checks the instruments of a light truck immobilized with wheel chocks beside a kerb.
The key idea

Check your braking system and its response before starting your journey.

Remember

  • Secure your lorry while pressure builds to the required level.
  • Check pressure and warnings as your manual instructs.
  • Check accessible pipes and connections for damage or leaks.
  • Do not go beneath an unsecured vehicle.
  • Do not touch hot parts or put your face near leaks.
  • Test the service brake at low speed in a suitable place.

Exam trap: Wrong: you test emergency braking in normal traffic. Right: you check at low speed in a suitable place.

Read the full explanation
  • You must secure the lorry while the system reaches its operating conditions. Check the circuit pressures and the warning system's self-check in accordance with the manual before moving off.
  • You must inspect accessible pipes and connections without going underneath an unsecured vehicle. Look for damage, chafing, loose connections and abnormal leaks; also check any available wear indicators. Do not touch hot components or put your face near a leak to locate it.
  • In a suitable place, you must check at low speed that the service brake response is normal, progressive and balanced, following the operating instructions. Do not carry out emergency braking tests on a road open to traffic.
  • You must familiarise yourself with your lorry's braking and speed reduction controls and check them in accordance with its manual.

14Leaks and loss of effectiveness

A driver wearing a reflective vest makes a phone call beside a light truck stopped in a refuge off a rural road.
The key idea

If a major fault occurs, stop safely and arrange repairs.

Remember

  • Do not pump an air brake pedal: you can use up your reserve.
  • If you pull sideways during braking, braking force may differ between sides.
  • Consider wheel and tyre condition too.
  • Keep control and use available braking as your manual instructs.
  • Do not stop the engine while moving to try to brake.
  • Request assistance and repairs before driving again.

Exam trap: Wrong: every pressure drop means a leak. Right: suspect a leak if pressure falls rapidly without explanation, with your vehicle secured, engine stopped, and no brakes or other air users operated; check your manual’s tolerances.

Read the full explanation
  • If you notice a rapid, unexplained drop in pressure with the vehicle secured, the engine stopped and no brakes or other air-consuming equipment being operated, you must suspect a leak. Air consumption per application and permissible variations are assessed against the tolerances in the manual.
  • You must not pump the air brake pedal to build pressure: each application and release can use up the reserve. If air production does not keep up with consumption, repeating them makes the situation worse.
  • If the lorry pulls to one side only during braking, you must consider unequal braking force on the two sides, as well as the condition of the wheels and tyres. Do not automatically attribute the fault to the steering or to a specific component.
  • In the event of a major failure, you must maintain control, use the available means of slowing down in accordance with the manual and stop in a safe place. Do not switch off the engine while moving to try to brake, or continue your journey at low speed with the fault. You must arrange assistance and repairs before using the lorry again.

15Hydraulic circuits and wet brakes

A person checks the brake fluid reservoir level under the open bonnet of a light truck parked with the kerb on its right.
The key idea

Check your brake fluid and test your brakes after driving through water.

Hydraulic brake pedalPossible fault to investigate
SpongyAir in the circuit
Abnormally hardLoss of assistance

Remember

  • If your system is hydraulic or combined, use the specified fluid.
  • Check that the level is between MIN and MAX.
  • Investigate any abnormal fall; do not simply top up.
  • Follow the specified fluid maintenance and replacement interval.
  • After driving through water, check your brakes only when safe.
  • To dry them, brake gently as instructed; stop if braking does not recover.

Exam trap: Wrong: pumping repairs a spongy pedal. Right: it may indicate air; investigate the cause.

Read the full explanation
  • If your light lorry uses hydraulic braking or a combined system, you must identify the relevant reservoir and the specified fluid. Check that the level is between the MIN and MAX marks and check maintenance in accordance with the manufacturer's instructions. Topping up without investigating an abnormal drop can conceal a leak; you must also avoid confusing brake fluid with condensate from the air reservoirs.
  • If your hydraulic brake pedal feels spongy or temporarily improves after several applications, this may indicate air in the circuit. An abnormally hard pedal may be associated with a loss of assistance. [DGT, «Brakes, a key safety component»](https://revista.dgt.es/es/motor/tecnologia-seguridad/2025/1015-N275-vehiculo-al-dia-frenos.shtml).
  • You must follow the brake fluid replacement interval and specifications. Bleeding the hydraulic system removes air when necessary and requires you to identify the cause; pumping the pedal does not repair the fault.
  • After driving through water, you must check that the brakes respond correctly. If conditions allow a safe check, gently apply the service brake in accordance with the manual to help dry them. Do not brake sharply as a test or continue if they do not regain their effectiveness; water can also conceal damage or a dangerous depth.

16ABS and wheel lock

A light truck travels within its lane beside a fallen flowerpot at the edge of the road, with the driver and steering wheel on the left side of the cab.
The key idea

With working ABS, maintain firm braking in an emergency.

Remember

  • ABS limits wheel locking.
  • It helps you keep stability and steering control.
  • Choose a safe path and leave room around obstacles.
  • Do not pump or ease off because of normal ABS vibration.
  • If a fault warning appears, check your vehicle’s message.
  • Do not rely on the affected anti-lock function.

Exam trap: Wrong: ABS always shortens braking distance. Right: this depends on the surface; speed, load and grip still matter.

Read the full explanation
  • ABS means anti-lock braking system. Its sensors monitor wheel rotation and its control system adjusts pressure to limit wheel lock during braking.
  • Its main advantage is that it helps you maintain stability and steering control while braking hard. This does not allow you to steer any way you like; a tyre has a limited capacity to combine braking and lateral force. You need a feasible path and clearance from obstacles.
  • In an emergency with ABS working, you must apply the brake firmly and keep it pressed while steering the lorry along a safe path. Do not pump the pedal or ease off simply because you feel vibrations or hear noises caused by the system's operation. [DGT, «Brakes: how to use them correctly»](https://revista.dgt.es/es/educacion-formacion/conducir-mejor/2023/0315-Frenadas.shtml).
  • You must not answer that ABS always shortens braking distance. On certain surfaces it may not reduce it, and it never eliminates the effects of speed, load and grip. If a fault warning appears, you must interpret the vehicle's message: basic braking may remain available, but you cannot rely on the affected anti-lock function.

17EBS and electronic coordination

A light truck travels to the right with the driver on the left side of the cab and a partial view of the secured load, electronic controller, and electrical and pneumatic brake connections.
The key idea

Understand electronic brake coordination and heed its fault warnings.

SystemFunction you must distinguish
EBSElectronic braking control
ABSLimits wheel locking
Conventional load-dependent valveAdjusts rear braking to the load

Remember

  • EBS may coordinate service brakes and retarders, depending on your equipment.
  • Respect the authorised load and secure your goods correctly.
  • Do not alter the load-dependent brake valve’s adjustment.
  • Heed warnings from your lorry and trailer.
  • A backup system does not guarantee every function remains available.

Exam trap: Wrong: EBS removes the need for air. Right: in an electro-pneumatic system, air still provides braking force.

Read the full explanation
  • EBS means electronic control of the braking system; ABS refers to its anti-lock function. EBS interprets your braking demand and controls modulators close to the actuators to improve coordination and response times. In a lorry with an electro-pneumatic system, the command can be transmitted electrically while the force is still produced by air.
  • EBS can adapt brake force distribution to the load and coordinate the service brakes and retarders, depending on the equipment. You must comply with the authorised load and stow it correctly: electronics do not correct overloading.
  • In a conventional air brake system, you may find a load-dependent brake compensating or regulating valve: it adjusts the pressure sent to the rear axle brakes according to the load carried and limits the risk of wheel lock when unladen. You must keep its mechanism and connections in good condition without altering its adjustment. The inspection includes the load-sensing valve. [RD 563/2017, Annex II, section 1.1.17](https://www.boe.es/eli/es/rd/2017/06/02/563/con).
  • You must respond to EBS warnings from the lorry and trailer. A fault can cause loss of electronic functions or reduced performance, with a fallback response provided by the manufacturer.
  • With trailer equipment, you must distinguish between the electrical power supply, electronic communication and backup pneumatic control. The availability of a backup path depends on the equipment and the fault; it does not guarantee that all braking functions remain available. [UN Regulation No. 13, sections 5.1.3.1 and 5.1.3.4.1](https://www.boe.es/doue/2026/746/L00001-00303.pdf).

18Engine braking and keeping a gear engaged

A light truck driver descends a road through hills with both hands on the steering wheel, feet away from the pedals and the tachometer needle in the green zone.
The key idea

Choose a suitable gear before your downhill speed becomes excessive.

Remember

  • Keep the transmission engaged to use engine braking.
  • Do not coast downhill in neutral.
  • Avoid sudden downshifts and exceeding the permitted engine speed.
  • Adapt your gear to weight, slope and available braking effect.
  • Know your automated gearbox’s descent programme.
  • Respect the limits shown on your rev counter.

Exam trap: Wrong: always descend in the gear used uphill. Right: this is only a guide; check whether it suits the descent.

Read the full explanation
  • You must make use of engine braking when you release the accelerator, with a suitable gear selected and the transmission engaged. In a diesel lorry, you may also have dedicated systems that increase this braking effect.
  • You must select the gear before your speed on the descent becomes excessive. A low gear allows you to maintain an engine speed that provides useful engine braking, within the range permitted by the manufacturer. Do not change down abruptly to a gear that causes the engine to over-rev: the wheels can drive the engine even when you are not accelerating.
  • You must keep the transmission engaged to retain engine braking. With an automated gearbox, you must know how to select or hold a gear and select the descent programme.
  • You must adapt your choice to the mass, gradient and engine braking capacity. The gear used uphill serves as a guide, but is not guaranteed to be suitable downhill. There is no single gear or engine speed for every mountain pass and lorry: learn to interpret the rev counter and your vehicle's limits.

19Exhaust and compression brakes

A green light truck travels downhill in the right lane of a rural road, with the driver and steering wheel on the left side of the cab and the passenger seat empty.
The key idea

Use auxiliary engine braking as instructed to reduce work for your wheel brakes.

SystemHow it creates resistance
Exhaust brakeRestricts exhaust gas flow
Compression brakeActs on the engine valves

Remember

  • Your exhaust brake needs the transmission engaged.
  • Use the controls and conditions specified by the manufacturer.
  • Do not block the exhaust or alter its protective devices.
  • Do not rely on these systems alone to stop completely.
  • If braking is insufficient, use the service brake and adapt your driving.

Exam trap: Wrong: auxiliary braking replaces your service brake. Right: it helps control speed but cannot provide the complete final stop alone.

Read the full explanation
  • In an exhaust brake, restricting the flow of exhaust gases creates back pressure that opposes the engine's movement. This resistance reaches the driven wheels through the engaged transmission.
  • You must operate it using the control and under the conditions specified by the manufacturer. Its operation may be coordinated with fuel injection cut-off and gear selection. You must not improvise an exhaust obstruction or modify its protective devices to increase the braking effect: you can damage the engine.
  • You may encounter a compression engine brake, which alters valve operation so that the engine absorbs energy. It works differently from an exhaust butterfly valve.
  • These are auxiliary systems for controlling speed and reducing the load on the wheel brakes. Their effectiveness depends on engine speed and design, and you cannot rely on them as your only means of bringing the vehicle to a complete stop. If the available braking effect is insufficient, you must slow down using the service brake and adjust your approach.

20Hydraulic retarder

A light truck shows a cutaway of the hydraulic retarder connected to the transmission, with the orange rotor, green stator and blue fluid clearly distinguished.
The key idea

Watch your hydraulic retarder’s heat to preserve its braking effect.

Remember

  • The rotor and stator create resistance through a fluid.
  • Absorbed energy turns into heat.
  • Watch temperature and cooling.
  • If it gets too hot, its braking effect may decrease.
  • Use the control and fluid specified by the manufacturer.

Exam trap: Wrong: your hydraulic retarder does not heat up. Right: it generates heat and may limit its braking effect.

Read the full explanation
  • In a hydrodynamic retarder, you can identify a rotor and a stator that generate resistance through a fluid. Its location and integration with the gearbox depend on the model.
  • The energy absorbed turns into heat. You must monitor its temperature and cooling: if it gets too hot, the system may limit its braking effect, requiring you to make greater use of the service brake.
  • You must use its settings or integrated control as instructed in the manual and comply with the specified fluid and maintenance requirements. Its capacity depends on rotational speed and its thermal limits.

21Electric retarder

A light truck with the driver on the left descends a rural road and shows an electromagnetic retarder in the drivetrain releasing heat.
The key idea

Your electric retarder brakes through a magnetic field and produces heat.

Remember

  • The rotor turns and the stator stays still.
  • There is no rubbing contact between them.
  • Select the intensity to suit your equipment.
  • Its braking capacity depends on rotational speed.
  • Do not use it to hold your lorry still.

Exam trap: Wrong: this retarder always charges your battery. Right: conventional electromagnetic equipment releases the absorbed energy as heat.

Read the full explanation
  • In an electromagnetic eddy-current retarder, coils create a magnetic field that induces currents and torque opposing rotation. You can identify rotating rotors and a fixed stator, with no frictional contact between them.
  • You may find it fitted in the driveline, with its arrangement and mountings depending on the vehicle. The energy absorbed dissipates as heat; conventional equipment does not recover this energy to charge the battery.
  • You must select the braking level according to the equipment. Its capacity varies with rotational speed, and it does not hold the lorry stationary as the parking brake does.

22Retarders and poor grip

A green and orange light truck travels in the right-hand lane over patches of ice, with the driver and steering wheel on the far left side of the cab.
The key idea

Limit your retarder’s intensity when grip is poor.

Remember

  • Too much retardation can make your driven wheels slide.
  • On ice, snow or very slippery roads, avoid sudden activation.
  • Follow the manufacturer’s restrictions.
  • Check whether your ABS coordinates or interrupts the retarder.
  • Know how your lever, pedal and automatic programmes work together.
  • In an emergency, brake at once rather than looking for another control.

Exam trap: Wrong: you suddenly increase retarder intensity on ice. Right: you limit its braking effect and follow the manufacturer’s restrictions.

Read the full explanation
  • The braking effect of these systems reaches the driven wheels through the transmission. When grip is poor, you must limit their braking level: excessive retardation can make the wheels slide even without you pressing the service brake pedal.
  • On ice, snow or a very slippery road surface, you must avoid abrupt activation and follow the manufacturer's restrictions. Coordination with ABS may reduce or interrupt retarder operation when there is a risk of wheel lock; check which functions your lorry has.
  • You must know how the lever, pedal and automatic programmes work together. The sequence of auxiliary and service braking depends on the model; in an emergency, apply the brake without delaying to look for an auxiliary control.

23Brake fade and long descents

A light truck descends in its right-hand lane on a mountain road, with the passenger seat empty and the driver and steering wheel on the far side of the cab.
The key idea

Prepare for descents to prevent heat reducing your brakes’ effectiveness.

Remember

  • Before descending, slow down and choose a suitable gear.
  • Use auxiliary braking and add service braking when needed.
  • Do not hold the lorry back with light, continuous brake pressure.
  • Use an emergency escape lane if you can reach it safely; S-16 marks one.
  • If you notice smoke, strong smells or weaker braking, seek a safe stop.
  • Do not pour water on hot brakes; find the cause before continuing.

Exam trap: Wrong: normal pressure rules out brake fade. Right: heat can reduce braking even when the pressure gauge reads normally.

Read the full explanation
  • Brake fade is a loss of effectiveness caused by excessive heat. High temperatures can reduce the performance of the friction surfaces; in hydraulic systems, boiling brake fluid can also cause problems.
  • Before starting a long descent, you must slow to a controllable speed and select a suitable gear. Use the available auxiliary braking to limit acceleration and supplement it with the service brake when necessary. Do not wait until the lorry gains too much speed before looking for a low gear or the maximum retarder setting.
  • You must avoid holding the lorry back throughout the descent by applying light, continuous pressure to the service brake. When you need to adjust your speed, apply the brake in a controlled way as instructed in the manual, and allow it to release and cool.
  • If you notice a strong smell, smoke, an inadequate response or an increasing need for effort, you must find a safe place to stop before losing control. A normal pressure gauge reading does not rule out overheated brakes. Do not cool them by pouring water over them or continue to your destination because they respond again after a pause: you must investigate the cause.
  • If the service brake loses effectiveness during the descent, you must maintain your course, use the means of slowing down that remain available and find a safe stopping area, including an emergency escape lane if you can reach one. Use the secondary braking controls as appropriate for the vehicle, avoiding abrupt application of the parking brake.
  • The S-16 sign, ‘Emergency escape lane’, indicates an exit from the carriageway designed to stop a vehicle in the event of brake failure. If you need to use it, maintain your course and follow its entrance. [Official catalogue, S-16, RD 465/2025](https://www.boe.es/boe/dias/2025/06/17/pdfs/BOE-A-2025-12199.pdf?origen=app).

24Trailer brakes and connections

A light truck travels to the right towing a small trailer attached by the main hitch and a safety chain that stays above the ground.
The key idea

Respect your licence limits and secure your trailer correctly.

750 kgMaximum trailer MMA with C1
Up to 1,500 kg without breakaway brakingTrailer: secondary coupling
3,500 kgO2 overrun brake limit
For trailers with two-line air systemsFunction
RedAir supply
YellowBrake control

Remember

  • With C1, you can tow a trailer up to 750 kg MMA.
  • It may have no brakes if it stays within your lorry’s towing capacity.
  • O2 overrun brakes: over 750 kg to 3,500 kg; C1 limits still apply.
  • Secure both vehicles before handling connections.
  • Conventional air systems: connect control before supply; disconnect supply first.
  • Apply the parking brake to keep your detached trailer still.

Exam trap: Wrong: an unbraked light trailer needs no secondary coupling. Right: up to 1,500 kg MMA without automatic breakaway braking, use a chain or cable that prevents the drawbar touching the ground and retains some trailer guidance.

Read the full explanation
  • With C1, you can tow a trailer with an MMA (maximum authorised mass) of up to 750 kg. Above this, you need the appropriate licence for the combination. [RGCond, art. 4.2](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • You can tow a trailer with an MMA of up to 750 kg without its own brakes, within the lorry's towing capacity. An overrun brake may be permitted as the service brake on O2 trailers, with an MMA of more than 750 kg and up to 3,500 kg: when the trailer pushes against the towing vehicle during deceleration, the device applies the trailer's brakes. This does not extend your C1 entitlement. [RGV, art. 12.8.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12) and [Annex VIII, table of categories O1 and O2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anviii).
  • If the trailer has an MMA of up to 1,500 kg and has no automatic braking if the coupling breaks, you must have a secondary coupling, such as a chain or cable. It must prevent the drawbar from touching the ground and retain some steering control over the trailer if the main coupling separates; this requirement also applies to the light trailer you can tow with C1. [RGV, art. 13.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • On trailers with a two-line pneumatic connection, red identifies the air supply and yellow the brake control line. The trailer's reservoir provides the energy, and the control line communicates the braking demand. This is technical knowledge about heavy-vehicle systems, rather than the usual equipment on a light C1 trailer. [ISO 1728:2006, section 3.4](https://cdn.standards.iteh.ai/samples/44103/9dde57923d1643f3979ac97bc5bb13f8/ISO-1728-2006.pdf).
  • The air hoses, ABS/EBS connector and lighting connector have different functions. Secure both vehicles before handling them and follow the manufacturer's procedure: in a conventional system, connect the control line before the supply line, and disconnect the red supply line first.
  • Automatic braking on separation must stop the trailer without impairing the braking effectiveness of the rest of the combination. The parking brake holds it stationary when detached. [RGV, art. 12.8.3 and Annex VIII, section 1.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).

25Accelerator and power demand management

A driver in the cab of a left-hand-drive light truck presses the accelerator with the right foot, with the pedal area clear of obstructions.
The key idea

Monitor your speed and know what to do if your accelerator sticks.

AidWhat it does when you use it
Cruise controlMaintains your selected speed
LimiterRestricts power demand according to its setting

Remember

  • Keep the accelerator movement clear and its connections maintained.
  • Watch your downhill speed, even with automatic aids.
  • If the accelerator sticks, press the clutch or select neutral.
  • Brake continuously and steer to a safe stop.
  • Cancel cruise control if active; keep the engine running for assistance.
  • Arrange repairs before continuing.

Exam trap: Wrong: you rely on cruise control or the limiter to fix a stuck accelerator. Right: you separate engine and wheels, brake and stop safely.

Read the full explanation
  • With the electronic accelerator pedal, you request power: its sensor sends the pedal position to the engine management unit, which regulates fuel injection according to that demand and the operating conditions. You must keep the pedal's travel unobstructed and its connections in good condition.
  • With cruise control, you can maintain a selected speed without continuously pressing the accelerator; the speed limiter restricts power demand to prevent you from exceeding its setting. You must know how to cancel these systems and monitor your speed on descents, where gravity may make braking necessary. The rules on fitting speed limiters are covered in the «Dimensions and masses of the light lorry» module.
  • When you request engine braking, the system may cut off fuel injection while the wheels drive the engine with a gear engaged. In integrated systems, a request for retarder braking may also coordinate this fuel cut-off; the retarding effect comes from the retarder itself. You must follow the manufacturer's requirements for engine speed and operation.
  • If the accelerator sticks, you must press the clutch pedal or select neutral to disconnect the engine from the wheels, apply the brakes steadily and steer the lorry to a safe stop. Cancel cruise control if it is active. Keep the engine running during the manoeuvre to retain power assistance, and arrange for repairs before continuing.

Prepare the pneumatic system before setting off

Check the air reserve, warnings and response before joining traffic.

  1. Secure your lorry and visually check accessible components without exposing yourself to movement or pressurised air.
  2. Put the system into operation according to the manual and observe the warning system self-test.
  3. Wait until all required circuits reach their operating conditions; interpret any differences or abnormal pressure recovery.
  4. Check that there are no warnings that prevent you from driving and no abnormal leaks.
  5. At low speed in a suitable place, check that the service brake responds progressively and evenly.
  6. If you detect a major defect, keep the vehicle immobilised and arrange repairs.

Control a long descent

Maintain your speed without exhausting the brakes’ capacity to absorb heat.

  1. Before the slope, assess the mass, grip, length of the descent and available braking assistance.
  2. Reduce your speed and select a gear that provides braking assistance within the permitted engine speed range.
  3. Apply the engine brake or retarder progressively, as appropriate for the grip and equipment.
  4. Adjust your speed with the service brake when necessary, following the manual, and avoid keeping it lightly applied continuously.
  5. Monitor engine speed, pressure, temperature and warnings; adjust your speed if the retarder limits its power.
  6. If braking efficiency decreases or signs of overheating appear, find a safe place to stop and arrange an inspection.

Brake in an emergency with ABS

Maintain braking pressure and steer along a feasible path.

  1. Press the service brake pedal firmly as soon as you identify the danger.
  2. Maintain braking pressure even if you feel vibrations or hear the system regulating braking; do not pump the pedal.
  3. Steer your lorry with controlled movements towards a space you can reach, without attempting a turn beyond the available grip.
  4. Once stopped, secure the vehicle and assess any damage or warnings before continuing.

Check a trailer’s pneumatic connections

Technical knowledge for heavy trailers; the light trailer allowed with C1 may have no brakes of its own. Follow the manufacturer’s procedure.

  1. Immobilise and secure both vehicles before touching the lines.
  2. Identify the red supply line, yellow control line and ABS/EBS electrical connector; check seals and couplings.
  3. With conventional connections, prepare and connect the control line before supplying air; connect the electrical equipment according to its manual.
  4. Check that the couplings are locked, the hoses can move freely, air pressure builds up, there are no leaks and the brakes respond.
  5. Before uncoupling, apply the parking brake and the specified securing measures; disconnect the red supply line first and then the control line according to the equipment’s procedure.
  6. Protect disconnected connections from dirt and check that the trailer is effectively immobilised.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module