Theory · C1 Licence - Light Truck · Module 13 of 18

Lorry driving techniques

You learn to manage visibility and the space your C1 lorry needs, including blind spots, turns, roundabouts and reversing with a guide. You learn to prepare for descents, respond to wind and adverse weather and secure your lorry when immobilised, applying the distinctions between technical recommendations and legal obligations tested in the exam.

35 min read25 sectionsReviewed Nov 3, 2026
A light box truck travels within its lane on a road with a broad bend among hills and cypress trees.
Truck driving with a safety margin

1Anticipate to maintain a safety margin

A light truck with its driver seated on the left approaches a pedestrian crossing in its right-hand lane, leaving ample space before a pedestrian who is crossing.
The key idea

Look ahead and leave space to respond to danger.

Remember

  • Look far ahead, nearby, sideways and in your mirrors.
  • Check that you can enter, turn and leave your destination.
  • Choose your speed for what you can see and handle.
  • Slow further or stop if danger requires it.
  • Even in a small lorry, allow for turns and hidden areas.

Exam trap: Wrong: you know the road, so you can relax. Right: keep checking for risks and leaving space.

Read the full explanation
  • Drive with observation, anticipation and space: identify what is happening, anticipate how it develops and keep a margin to respond. In a C1 lorry with an MMA (maximum authorised mass) of more than 3,500 kg and up to 7,500 kg, the length, cab height and response to the controls require you to prepare your decisions in good time. Having a smaller vehicle than other lorries does not eliminate its swept path or blind spots; knowing a road does not eliminate its risks either.
  • Alternate brief checks of the road ahead in the distance, the area nearby, the sides and the mirrors. Look for traffic queues, junctions, hidden pedestrians and vehicles that disappear from your mirrors.
  • Plan access all the way to your destination, including the yard, loading bay and exit. Check whether your dimensions allow you to enter, turn and leave without getting trapped; a route suitable for a car may force you into manoeuvres that your lorry cannot carry out.
  • Keep control of your vehicle and adapt your driving to what you can actually see and deal with. Driving below the maximum speed does not guarantee a safe speed: a wet bend, a hidden junction or a nearby pedestrian may require you to slow down much more or stop. [RGC, art. 17](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a17). [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45).

2Prepare your driving position and visibility

The driver of a light truck stopped beside the kerb looks towards the right mirror while a woman stands on the pavement beside the truck.
The key idea

Adjust your driving position and check your view before moving off.

Remember

  • Adjust your seat before setting your mirrors.
  • If you move the seat, check the mirrors again.
  • Clean windows, mirrors and cameras; remove obstructions and mist.
  • Check wipers and washers before driving in rain.
  • Look in front and to your right before moving off.
  • After waiting, check again before moving.

Exam trap: Wrong: hold an awkward posture to see in your mirror. Right: adjust your mirror from your normal driving position; check it again if you move your seat.

Read the full explanation
  • Adjust your seat, steering wheel and supports so you can operate the pedals without stretching or crouching excessively. Then adjust your mirrors from your normal driving position: if you change the seat position, check the fields of view again. Avoid holding an awkward posture to compensate for a poorly adjusted mirror.
  • Check that the windscreen, windows, mirrors and cameras are clean and give you a clear view. Remove obstacles that block your view ahead or to the sides; a small object close to your eyes can hide a person some distance away. Condensation and reflections also reduce useful visual information.
  • Check the wiper blades and windscreen washer before a journey in rain. If the wiping action is uneven, check for dirt, correct adjustment and the condition of the rubber blades; replace any damaged blades.
  • Before moving off, check your immediate surroundings, especially in front of the cab and along the right-hand side. A person may approach while you are stationary. Check again after a wait and before moving off: the check you make on arrival does not necessarily reflect the surroundings when you leave.

3What each mirror class shows

A light truck with the driver on the left is stopped beside the right-hand kerb, and its mirrors show the rear area, a wider side view and the ground close to the cab.
The key idea

Know what each mirror shows and keep required viewing devices.

7.5 tN2: your lorry’s equipment table
more than 2 mClass V: fully laden height
Mirror and vehiclesView / equipment for N2 up to 7.5 t
I interiorOptional in your lorry
II main: M2, M3, N2 and N3Behind, on both sides; compulsory on your lorry’s left and right
III main: M1 and N1Behind, on both sides
IV wide-angleMore of the side and rear; optional unless the compulsory class II is not convex
V close-proximityGround beside the cab; optional only if more than 2 m above ground when fully laden, in every adjustment position, including all adjustment points and mountings; otherwise fitting is prohibited
VI front-viewIn front of the cab; according to type approval

Remember

  • Do not judge distances using only your wide-angle mirror.
  • Keep two compulsory class II mirrors: one left and one right.
  • If a compulsory class II mirror is not convex, add class IV that side.
  • Class VI depends on type approval; it is not in the RGV table.
  • Keep the devices required by your vehicle’s type approval.
  • Before fitting class V, check its height with your lorry fully laden.

Exam trap: Wrong: a parking camera replaces a compulsory mirror. Right: only a system type-approved for that purpose can replace it.

Read the full explanation
  • The main exterior rear-view mirrors show the area behind you on both sides; the class IV wide-angle mirror extends your view to the side and rear, and the class V close-proximity mirror shows the ground near the cab. The wide-angle image can make distances difficult to judge. [RGV, Annex III, sections 1 and 2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • Class II is the main rear-view mirror for M2, M3, N2 and N3; class III is the main mirror for M1 and N1. [RGV, Annex III, sections 1 and 2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • Class VI is the front-view mirror: it lets you observe an area in front of the cab. Its requirements come from UNECE R46 type approval; it does not appear in the equipment table in Annex III of the RGV. [UNECE Regulation 46](https://www.boe.es/buscar/doc.php?id=DOUE-L-2010-81254).
  • For your N2 lorry of up to 7.5 t, the table requires two class II main rear-view mirrors: one on the left and one on the right. A class I interior mirror, a class IV wide-angle mirror and a class V close-proximity mirror are optional. If a compulsory class II mirror is not convex, you must also have a class IV mirror on the same side. You may only fit a class V mirror if, with the vehicle fully laden, it remains more than 2 m above the ground in every adjustment position, including all its adjustment points and mountings; if this condition is not met, fitting it is prohibited. [RGV, Annex III.2, N2 ≤7.5 t table and notes 2 and 3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • Keep the devices required by your vehicle's type approval. An auxiliary parking camera cannot replace a compulsory rear-view mirror; any system that replaces it must be type-approved for that function. [UNECE Regulation 46](https://www.boe.es/buscar/doc.php?id=DOUE-L-2010-81254).

4Blind spots and vulnerable road users

A light box truck remains stopped before turning right with its indicator on, while a helmeted cyclist is stationary between its right side and the kerb.
The key idea

Check hidden areas before moving your lorry.

Remember

  • If a cyclist disappears from view, wait until you can rule out danger.
  • Check the gap on your right before turning.
  • Use direct vision, mirrors and cameras together.
  • Stop if you cannot check that your manoeuvre is safe.
  • Keep pedestrians visible; do not hide lights, plates or hand signals with your load.
  • Leave space ahead; do not wave other drivers past.

Exam trap: Wrong: a high cab lets you see everything. Right: check nearby hidden areas too.

Read the full explanation
  • Look for hidden areas in front of the cab, beside its doors, along the sides and behind the load body. Your high driving position improves some of your view into the distance, but it can prevent you from seeing low objects and people nearby. No single mirror check guarantees that the entire area around your vehicle is clear.
  • When a cyclist or motorcycle disappears from a mirror, do not assume they have left the area around you. They may still be alongside you. Keep track of their last position and check the available fields of view before manoeuvring; if you cannot rule out danger, wait.
  • When turning right, pay particular attention to the space between your lorry and the kerb. A cyclist may move forward through this gap and be exposed to the rear wheels. Your indicator signals your intention, but it does not replace checking or oblige anyone there to disappear.
  • Combine direct observation, mirrors and aids without focusing on a screen for too long. Cameras may be dirty, show reflections, leave areas uncovered or display an image that is difficult to interpret. If visibility is insufficient for a safe manoeuvre, stop and arrange an adequate check before continuing.
  • The enclosed load body and the load may prevent a direct view to the rear, even if your cab has a rear window. A poorly positioned tarpaulin or goods placed in front of a viewing device can also hide areas to the sides; arrange your load so that you retain the necessary field of view. [RGC, art. 18](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a18).
  • When you stop near a pedestrian crossing or junction, your load body and load may hide pedestrians from other drivers. Choose a position that leaves visibility and space to cross; avoid blocking the crossing. [RGC, art. 59](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a59).
  • A car close behind you can barely see the road ahead. Keep space between you and the vehicle ahead to help observation and overtaking. Oncoming drivers may not see a car pulling out from behind your load body to overtake you: avoid gestures inviting it to overtake, as you cannot fully assess its view either.
  • Your load and its securing equipment must not hide lights, plates or hand signals. A projection may be difficult for someone approaching at night or from the side to see, even if it seems obvious from your cab. Check how clearly it can be seen before driving; the positioning and marking of projections are covered in “Load securing and safety”. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).

5Space to brake and observe

A green light truck follows an orange car with a large gap between them on a wet road in the rain.
The key idea

Leave braking space and keep the following distances required for your situation.

50 mMinimum to help others overtake
150 mMinimum while moving in tunnels
six secondsAlternative tunnel minimum
SituationVehicles affectedDistance
Following without signalling an intention to overtakeMMA (maximum authorised mass) over 3,500 kg or overall length over 10 mAt least 50 m
Built-up areas; overtaking prohibited; several lanes in your direction; congestion prevents overtakingVehicles over 3,500 kg MMA or over 10 m longThat minimum does not apply; keep a safe distance
Tunnel or underpass; moving without intending to overtakeLorries over 3,500 kg MMAAt least 150 m or six seconds; increase if needed

Remember

  • Increase your distance in rain or poor visibility.
  • Consider your load, speed, grip and brakes.
  • Always leave enough room to avoid hitting the vehicle ahead.

Exam trap: Wrong: always apply 50 m. Right: that minimum helps overtaking under its stated conditions. In tunnels and underpasses, while moving without intending to overtake, your lorry over 3,500 kg MMA must leave at least 150 m or six seconds.

Read the full explanation
  • Leave enough distance to avoid a rear-end collision if the vehicle ahead brakes sharply. Assess your actual speed, grip, load and brake response. Increase your margin in rain or reduced visibility, even when you do not intend to overtake. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54).
  • To make overtaking easier, if your MMA exceeds 3,500 kg or your total length exceeds 10 m, you must leave at least 50 m when following another vehicle without signalling your intention to overtake. This minimum is not required in built-up areas, where overtaking is prohibited, where there are several lanes in your direction or where traffic congestion prevents overtaking. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54).
  • In tunnels and underpasses, when you do not intend to overtake, you must keep a gap of at least 150 m or six seconds in your lorry with an MMA exceeding 3,500 kg. Increase this margin if safety requires it; this minimum applies to moving traffic, not a stationary queue. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95).

6Prepare for every manoeuvre

A driver seated on the left of a green light truck watches the road from a parking bay beside the kerb while an orange car travels left in the far lane.
The key idea

Look, signal and keep checking your space throughout each manoeuvre.

Remember

  • Choose a gap large enough for your whole lorry to join traffic.
  • Respect anyone already in the lane you want to enter.
  • Help others join traffic when you can do so safely.
  • Before slowing considerably, check behind and warn others if possible.
  • In immediate danger, act as urgently as needed.

Exam trap: Wrong: your indicator gives you priority. Right: signal and respect anyone occupying the lane.

Read the full explanation
  • Observe your surroundings, assess the space, signal and carry out the manoeuvre smoothly, continuing to watch throughout the movement. Your surroundings can change between your first check and the start of the turn. [RGC, art. 74](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a74). [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).
  • When moving off from a parking space or access point, check that you can join the traffic safely and give way where required. A laden lorry may accelerate slowly: you need a gap large enough to complete joining the traffic, not just to get the cab in front of another vehicle. [RGC, art. 72](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a72).
  • Respect road users already in the lane you intend to enter. Signalling and needing more space do not give you priority. If another road user tries to join the traffic, help their manoeuvre as far as possible without creating a risk; helping does not mean you automatically lose priority because of where they are coming from. [RGC, art. 74](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a74). [RGC, art. 73](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a73).
  • Before slowing down considerably, also check behind you and give a warning where possible. Anticipating a traffic queue lets you decelerate progressively, reducing the risk of a rear-end collision and load movement. In the face of imminent danger, act with the urgency necessary to avoid it. [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53). [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).

7Understanding a lorry's swept path

A rigid truck with a green cab and orange box body takes a right-hand bend with its wheels inside its lane and clearance from the inner kerb.
The key idea

Watch all the space your lorry needs when turning.

Remember

  • Your rear wheels pass inside the path of your front wheels.
  • Your rear end can swing outwards as you start turning.
  • Check mirrors, body, load and high obstacles too.
  • Leave space inside and outside your turn.
  • Stop if you do not know how much space is available.

Exam trap: Wrong: if your cab fits, everything fits. Right: check rear wheels, rear overhang and height too.

Read the full explanation
  • Picture the entire area your lorry occupies as you turn, not just the line followed by the cab. In a rigid lorry, the rear wheels follow a path further inwards than the front wheels. The tighter the turn, the more the rear wheels may cut inwards.
  • Watch the rear overhang: as you start a turn, the part behind the rearmost axle may swing outwards. If you turn right alongside a vehicle on your left, your rear end may move towards it even as your cab moves away.
  • Consider the upper parts too: mirrors, load body, refrigeration equipment and authorised load. A corner may pass over a kerb and strike a sign, a shelter or a branch. Having enough room for the wheels does not prove that the bodywork has all the height and width clearance it needs.
  • Plan a path with clearance on both the inside and outside, and check it in your mirrors as you turn. No single distance from the kerb suits every wheelbase, overhang or corner. If you do not know how much space is available, stop before wedging your vehicle into a confined space.

8Turning right without trapping anyone

A light truck with its right indicator on waits before turning at a corner while a cyclist remains to its right and ahead of the cab.
The key idea

Turn slowly and check that nobody becomes trapped on your right.

Remember

  • Slow down before the corner.
  • Check your right side, pedestrian crossing and destination road.
  • Normally, position yourself close to the right-hand edge before turning.
  • If your size prevents this, take precautions to avoid any danger.
  • Before moving sideways, check, respect others and signal.
  • Stop if someone enters danger; continue only after checking it is safe.

Exam trap: Wrong: your size gives you priority to swing out. Right: if your dimensions require extra room, avoid any danger and respect others.

Read the full explanation
  • Slow down before the corner and check your right-hand side, the pedestrian crossing and the road you are turning into. Also check the outside of your swept path. With a high cab, someone may be hidden immediately in front of you while you wait, even if you saw that the crossing was clear as you approached.
  • As a rule, you must position yourself close to the right-hand edge to turn right. If your vehicle's dimensions prevent you from doing so, you must take the precautions needed to avoid any danger; this exception does not allow you to swing out blindly or force other road users aside. [RGC, art. 75](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a75). [RGC, art. 76](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a76).
  • Prepare in advance for any extra room your lorry needs to turn, and avoid making it look as though you are turning the other way: the gap beside the kerb may attract bicycles or motorcycles just as you are about to close it. When moving across, carry out the checks and signalling explained in “Prepare for every manoeuvre”.
  • Move forwards slowly and make sure your rear axle clears the corner without mounting the pavement. Do not tighten your turn while another road user is still on your right. If someone enters the danger zone, stop before they become trapped and move off again only after checking that you can do so safely.

9Left turns and narrow entrances

A light truck remains in its lane beside a narrow warehouse entrance across the road while a car approaches in the opposite direction.
The key idea

Check that your whole lorry fits before entering a narrow access.

Remember

  • Check slopes, kerbs and overhead obstacles.
  • On two-way roads, approach the centre without entering the oncoming side beforehand.
  • Do not turn if you cannot see enough to turn safely.
  • If you need special positioning, plan ahead and watch both ends.
  • Arrange access so you can leave forwards where possible.
  • Before reversing, check that it is legal and safe.

Exam trap: Wrong: only your cab needs to fit. Right: check your whole lorry fits without blocking traffic.

Read the full explanation
  • Check that your entire lorry can cross and fit into the road you are entering without blocking traffic. An entrance may accommodate the cab but be too narrow for the load body. Also check access slopes, kerbs and overhead obstacles before committing to your path.
  • To turn left on a two-way road, you must move close to the line separating the two directions without moving onto the oncoming side in advance. If visibility is insufficient to turn safely, do not turn. Needing to enter a warehouse does not authorise you to force your way through. [RGC, art. 74](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a74). [RGC, art. 75](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a75).
  • When your vehicle's dimensions require special positioning, prepare the manoeuvre in advance and check both ends of your lorry. A sudden correction may give the cab enough space but cause the rear end to strike something or bring the inside wheels too close to the edge. [RGC, art. 76](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a76).
  • Plan your access so that you can drive out forwards where the site allows. If you need to reverse, first check that doing so is legal and safe.

10Roundabouts with a long vehicle

Overhead view of an orange light truck in the inner lane of a roundabout and a blue car slightly ahead in the outer lane, both within their lanes.
The key idea

Prepare your roundabout exit without cutting across other road users.

Remember

  • Slow before entering; allow space for your whole lorry.
  • Watch small vehicles alongside you.
  • Respect other lanes’ occupants and signal each lane movement.
  • Keep clear of the island: your rear wheels cut inwards.
  • Keep a low, steady speed.
  • If you cannot exit safely, continue along the permitted route.

Exam trap: Wrong: needing space lets you cut across others to exit. Right: respect occupied lanes and prepare your manoeuvre again.

Read the full explanation
  • Slow down before entering and anticipate how your axles and overhang clear the island and exits. A wide entrance may lead onto a narrow circulatory carriageway. Also watch for small vehicles that may move alongside you as you go round.
  • On a small roundabout, assess the lateral space your load body needs throughout your route around it, as well as the space your cab occupies on entry. Check adjacent lanes before committing to a path that may later need correcting; apply the rules for moving across in “Prepare for every manoeuvre”.
  • Avoid keeping the cab too close to the island, as the rear axle cuts inwards. At the same time, make sure the outside of your vehicle does not strike anyone travelling on your right. Keep your speed low and steady so that you can observe without making abrupt corrections.
  • Prepare to exit by moving safely into the appropriate lane according to the signs and markings. Do not cut across another vehicle's path from an inner lane. If you cannot exit safely, continue along the permitted route and plan your manoeuvre again; pressure from those waiting behind does not justify rushing. [RGC, art. 74](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a74). [RGC, art. 75](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a75).

11Reversing: limits and checks

A driver checks on foot behind a light truck stopped beside the kerb on its right and looks at a low bollard on the pavement.
The key idea

Reverse only when permitted and when you can check that it is safe.

15 mMaximum for certain supporting manoeuvres
SituationWhat you may do
You cannot move forwards, turn or turn roundReverse only as far as necessary
Reversing is essential to another manoeuvreCover only the necessary distance
Supporting stopping, parking or joining trafficMaximum 15 m; never enter a junction
Autopista or autovíaReversing prohibited

Remember

  • Cover only the necessary distance in permitted circumstances.
  • Never reverse on autopistas or autovías.
  • Check behind, beside and above your lorry, including for people.
  • Get out to check or ask for guidance if needed.
  • Use your reversing light; otherwise, extend your arm horizontally, palm facing backwards.
  • Reverse slowly; stop for warnings or any danger.

Exam trap: Wrong: you can always reverse up to 15 m. Right: this maximum applies when supporting stopping, parking or joining traffic, without entering junctions. Reversing is also prohibited on autopistas and autovías.

Read the full explanation
  • Reverse only in permitted circumstances: when you cannot move forwards, turn or turn around, or as a necessary part of another manoeuvre, covering only the distance needed. When reversing as part of stopping, parking or joining traffic, the maximum is 15 m and you must not enter a junction. Reversing is prohibited on autopistas (motorways) and autovías (dual carriageways). [RGC, art. 80](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a80).
  • Before reversing, check the space behind and at the sides, people, low obstacles, slopes and overhead clearance. You must get out or follow another person's directions if you need to do so to make sure it is safe. A camera aimed at the centre may not show an obstacle at a corner. [RGC, art. 81](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a81).
  • Signal the manoeuvre with your reversing light if you have one; otherwise, hold your arm horizontally with your palm facing backwards. The light signals your intention and may come on before you move; it does not establish that you have enough space or priority. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).
  • Reverse slowly, with the utmost care, and stop in response to warnings, nearby people, animals or vehicles, or whenever safety requires it. Abandon the manoeuvre if necessary. Do not assume that others hear your engine, alarm or warnings and move out of the way, including during a night-time delivery. [RGC, art. 81](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a81).

12Coordinating with a guide

A driver seated on the left side of a stopped light truck watches a spotter wearing a reflective vest raise an open palm from a safe position beside the vehicle in a loading yard.
The key idea

Stop if you lose sight of your helper or cannot understand their signals.

Remember

  • Agree who guides you, your route and the stop signal.
  • Keep your helper visible and outside your lorry’s path.
  • Never let your helper stand between your lorry and an obstacle.
  • With several helpers, agree who gives directions.
  • Also watch your cab and the side your helper cannot see.
  • Stop at any warning of danger.

Exam trap: Wrong: continue because your helper has not signalled stop. Right: if you lose sight of them or misunderstand a signal, stop until communication is clear again.

Read the full explanation
  • Before starting, you must agree who guides you, which route you take and which signal means stop. Use clear signals that you both understand. This coordination is a working precaution: it does not make your helper a traffic officer or relieve you of checking that the manoeuvre is safe.
  • Position your guide where they can watch the danger zone and you can see them directly or in a mirror, keeping them out of your path and swept area. Never let them stand between your lorry and a wall, loading bay or another vehicle to measure the gap while you move forwards.
  • If you lose sight of your guide or do not understand a signal, you must stop and restore clear communication before continuing. If you have several helpers, agree on a single person to give you directions to avoid conflicting instructions.
  • Also watch your cab and the side opposite the one your helper is watching. When you reverse while turning, the front swings sideways and may strike an obstacle. Stop at any warning of danger, even from someone else; your guide helps, but you remain in control of the vehicle. [RGC, art. 81](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a81).

13Approach a loading bay

A light truck is stopped and aligned in front of a loading dock, with the driver beside the visible left window and a worker waiting behind a railing outside the maneuvering area.
The key idea

Approach the loading bay slowly and secure your lorry before work starts.

Remember

  • Inspect the ground, slope, people and overhead space.
  • Check the bay fits your lorry and follow site rules.
  • Line up your lorry and check both sides.
  • Stop if you lose reference points or someone appears behind you.
  • Secure your lorry before getting out; check your surroundings when you return.
  • Do not move while workers, equipment or gangways are connected to your lorry.

Exam trap: Wrong: your helper can measure the gap behind while you move. Right: stop and keep them outside that danger area.

Read the full explanation
  • Inspect the access route before lining up: the surface, gradient, edges, pedestrians, forklifts and overhead clearance. Check whether the loading bay can accommodate your lorry and whether there are restraint systems or site rules you must apply. An open door does not guarantee that the area is ready to receive you.
  • Line up the vehicle using wide, planned movements where space allows, reducing the need for corrections as you approach. Keep your speed very low and check both sides; do not rely solely on a marking seen in one mirror. A slope or uneven surface can change the alignment of the load body.
  • Stop before making contact if you lose your reference points or people enter the area. Do not ask your assistant to go behind the lorry to check the remaining gap. If you need to get out, secure the lorry first and check your surroundings again when you return to the cab.
  • Once in place, apply the parking brake and the appropriate securing measures before allowing operations to begin. Clearly coordinate when staff can approach and when you intend to leave. Do not move off while workers, equipment or loading bridges are still connected to the vehicle.

14Bends, centre of gravity and rollover

A light truck with a green cab and tall orange cargo box rounds a bend on a rural road, upright and within its right-hand lane.
The key idea

Slow before bends and use smooth movements to avoid rolling over.

Remember

  • Enter bends at a safe speed without sudden movements.
  • Take extra care against rollover with a high load.
  • Avoid swerving around obstacles or when returning from the hard shoulder.
  • In a partly filled tanker, expect liquid to keep moving.

Exam trap: Wrong: you always skid before rolling over. Right: a high load can cause rollover before skidding, even with good grip.

Read the full explanation
  • Enter a bend at a speed that allows you to maintain your course and stability without sudden manoeuvres. Do most of your slowing down before turning and use the steering, brake and accelerator progressively.
  • A high load increases the risk of rollover, which can occur before a skid even with good grip. Slow down before tight bends, adverse cambers, edges and changes in level; load positioning is covered in “Load securing and safety”.
  • Avoid sudden steering movements to dodge small obstacles, mount a kerb or return from the arcén (hard shoulder). A violent correction can cause swaying and loss of stability. If you need to change course, reduce the risk by anticipating the situation and making controlled movements, keeping space between you and other road users.
  • In a partially filled tanker, the liquid can continue moving after braking or turning. Adjust your anticipation and smoothness to the fill level and compartments; see “Load securing and safety” for its distribution.

15Crosswinds and the shielding effect

A light truck with a tall box body travels in its lane beside trees bent by a crosswind, with the driver seated on the left side of the cab and holding the steering wheel with both hands.
The key idea

In crosswinds, slow down and steer gently.

Remember

  • Expect gusts on bridges and when leaving tunnels.
  • Hold your steering wheel firmly; avoid sudden steering.
  • Expect wind changes when passing or overtaking large vehicles.
  • Leave more sideways space in gusts.
  • Take care even when your lorry is empty.

Exam trap: Wrong: wind hardly affects an empty lorry. Right: its lower weight can also make it sensitive to gusts.

Read the full explanation
  • Expect greater exposure in a lorry with a tall body or a large side area. An empty vehicle can also be very sensitive to gusts because of its lower mass.
  • In crosswinds, moderate your speed, hold the steering wheel firmly and make gentle corrections. A suitable gear ratio can help you maintain responsiveness without straining the engine.
  • You can encounter a gust when leaving tunnels, crossing bridges or leaving the shelter of buildings and trees. You must also anticipate the shielding effect when meeting or overtaking a large vehicle: your exposure to the wind changes, and its force can then return.
  • In gusty conditions, increase your lateral safety margin; see the sections “Protect cyclists and other vulnerable road users” and “Passing immobilised vehicles and obstacles” in “Manoeuvres with your lorry” for the required clearances and speeds.

16Control a long descent

A light truck with an orange cab and green cargo box descends in its right-hand lane on a mountain road surrounded by dry hills and cypresses.
The key idea

Prepare before descending and combine engine braking with your service brake.

Remember

  • Choose your speed and gear before descending.
  • Consider the slope, weight, bends and grip.
  • Keep a gear engaged and respect engine speed limits.
  • Apply retardation gradually, following your manual.
  • On slippery roads, strong retardation can reduce grip.
  • If braking weakens or temperature warnings appear, seek a safe stopping place.

Exam trap: Wrong: descend in neutral or with the clutch pressed down. Right: keep a gear engaged and use retardation according to your manual.

Read the full explanation
  • Before the descent, choose your speed and gear according to the gradient, mass, bends and grip. Keep a gear engaged and progressively use the available engine braking and retardation as instructed in the manual, keeping within the engine's permitted speed range.
  • Supplement engine braking and retardation with the service brake and maintain a safety margin so you can stop. Strong engine braking or retardation can compromise grip at the driven wheels on slippery surfaces; follow the vehicle's instructions. If you notice reduced effectiveness or temperature warnings, find a way to stop safely. Detailed use of retarders and prevention of overheating are covered in “Brakes and retarders on light lorries”.

17Rain, spray and standing water

A green light truck travels in the rain on a wet road, leaving a wide gap behind the orange car ahead.
The key idea

In rain, slow down and leave more space to see and brake.

Remember

  • Take special care with the first drops of rain.
  • Keep your windows clean and free of mist.
  • Avoid spraying other road users when passing nearby.
  • Slow before standing water and keep your tyres in good condition.
  • If your tyres lose road contact, avoid sudden braking or steering.
  • Never cross water with unknown depth, current or ground underneath.

Exam trap: Wrong: brake sharply to test your brakes after a puddle. Right: after a safe puddle, check gently when safe. If normal braking does not return, stop and request assistance.

Read the full explanation
  • Reduce your speed and increase your separation when water reduces grip or visibility. The first drops of rain can mix with dirt and make the surface particularly slippery. Braking distance depends on the water, tyres, speed and road surface.
  • In a lorry, spray from your own and other vehicles can hide bicycles, road markings and obstacles. You must keep your field of vision clear of mist and dirt and leave room to react when a curtain of spray clears. Avoid driving too close to road users who could be affected by your spray.
  • Aquaplaning occurs when water prevents proper contact between the tyre and the road surface. You must prevent it by slowing down before standing water and keeping your tyres in good condition. If it occurs, avoid harsh braking and sudden steering movements; gently reduce the demands you place on the vehicle until you regain contact and control.
  • Do not drive through water if its depth, current or underlying surface is unknown. After driving through a safe puddle, check braking effectiveness when you can do so without danger, applying the brakes gently as instructed in the manual. If normal response does not return, stop and request assistance; harsh braking to test the brakes can create another hazard.

18Snow, ice and low-grip surfaces

A light truck travels in the right-hand lane and approaches a patch of ice in the shade of cypress trees, with a long clear stretch of asphalt ahead.
The key idea

On snow or ice, plan well ahead and avoid sudden movements.

0 °CTemperature for anticipating ice

Remember

  • In damp conditions near 0 °C, expect ice in shade, bridges and dips.
  • Slow before entering and greatly increase your following distance.
  • Use your steering, brakes and accelerator gently.
  • Choose a gear that lets you move without wheelspin.
  • Obey lorry restrictions even with chains or suitable tyres.
  • Wait without blocking snowploughs or other services.

Exam trap: Wrong: ABS restores the grip of a dry road. Right: slow down and leave much more space because ice limits grip.

Read the full explanation
  • In damp conditions with temperatures close to or below 0 °C, anticipate ice in shaded areas, on bridges, in dips and anywhere water can freeze. Shade helps ice persist, and a wet appearance does not guarantee grip. Slow down before entering and greatly increase your safety margin; neither the lorry's mass nor ABS restores the grip of a dry carriageway.
  • On snow or ice, you must use the accelerator, steering and brakes gently and avoid sudden changes in load on the axles. Select a suitable gear ratio that allows you to move without wheelspin and do not strain the engine. If you need to stop, prepare the manoeuvre much further in advance.
  • Check the specific restrictions for lorries and obey officers and signs. Having chains or suitable tyres does not authorise you to continue when access is prohibited for your vehicle category. Plan somewhere to wait where you can stay out of the way without blocking snowploughs or other services.
  • On ice, the increase in braking distance is very large and variable. You also need caution on wet road markings, metal covers or mud: avoid combining a tight turn with heavy braking or acceleration.

19Fog, smoke and suitable lighting

A light truck with the driver seated on the left travels in its lane with dipped headlights on along a road in daytime fog.
The key idea

In poor visibility, adjust your speed, following distance and lights.

LightWhen you may use it
Front fog lightsWhen visibility is significantly reduced, under the permitted conditions
Rear fog lightThick fog, very heavy rain, heavy snowfall or dense smoke or dust

Remember

  • Drive slowly enough to stop within the distance you can see.
  • Do not follow the lights ahead too closely.
  • Use the required lights during the day too.
  • In fog, dipped beam usually helps more than main beam.
  • Never drive using position lights alone.
  • Never enter smoke or dust assuming the cloud is short.

Exam trap: Wrong: any rain allows rear fog lights. Right: use them only in thick fog, very heavy rain, heavy snowfall or dense smoke or dust.

Read the full explanation
  • Adjust your speed so that you can stop within the distance you can see, and increase your following distance. Do not follow closely behind the lights of the vehicle ahead to find your way: you may follow it into an obstacle or hit it if it brakes. Use reference points in your lane without focusing all your attention on a single line.
  • When visibility is significantly reduced, you must use the appropriate lights even during the day. You may use front fog lamps, dipped beam or main beam under the permitted conditions; when driving in fog, dipped beam is usually more useful than main beam because of reflections. Position lights alone are not enough. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • Use the rear fog lamp only in thick fog, very heavy rain, heavy snowfall or dense clouds of smoke or dust. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • In smoke or dust, avoid entering on the assumption that the cloud will be short; check the conditions for using front fog lamps in “Lights and signalling on your light lorry”, section “Front fog lamps: permitted use”.

20Night driving and dazzle

A light truck with the driver and steering wheel on the left travels in its lane at night, its headlights illuminating a wooden crate farther ahead on the road.
The key idea

At night, choose your speed for the distance your lights illuminate.

Remember

  • Choose your lights for the road, its lighting and other road users.
  • Avoid dazzling others with main beam.
  • If dazzled, slow as necessary, even stopping.
  • Do not stare at the light dazzling you.
  • Keep windows clean and avoid reflections inside your cab.
  • If lights fail, slow down and seek a safe place to resolve it.

Exam trap: Wrong: keep your speed with faulty lights. Right: adjust your speed to the area illuminated and seek a safe place to resolve the fault.

Read the full explanation
  • Adjust your speed to the stretch of road illuminated by your lights, taking into account the distance you need to stop the lorry. A familiar road may have an unlit vehicle, a pedestrian or a fallen load on it. The height of your eyes does not remove the difficulty of distinguishing dark obstacles at ground level.
  • Select your lights according to the road, its lighting and the presence of other road users, following “Lights and signalling on your light lorry”, sections “Dipped beam: lighting the road ahead”, “Main beam: range and limits” and “Avoiding and dealing with dazzle”.
  • If you are dazzled, you must slow down as much as necessary, even stopping, to avoid hitting people or vehicles. Do not respond by keeping your main beam on or stare at the light source. Keep track of the road edge and your path while continuing to watch ahead. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102).
  • Avoid strong reflections inside the cab and keep the windows clean. If a fault reduces the lighting available, adjust your speed to the area actually illuminated and find a safe place to deal with it. Do not maintain your previous pace by relying solely on other vehicles' lights. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107).

21Choose and make a safe stop

A light truck is stopped beside the kerb on its right in a spacious paved stopping area, with clear space ahead and behind.
The key idea

Choose a permitted place with firm ground before stopping your lorry.

Remember

  • Check the ground can support your lorry.
  • Check the slope, edges and space for your lorry’s body.
  • Plan how you will leave and rejoin traffic.
  • Warn others early and slow gradually.
  • Watch behind and on the side you approach.

Exam trap: Wrong: having enough space is enough. Right: check the place is permitted, supports your lorry and lets you stop and leave safely.

Read the full explanation
  • Choose in advance a place where stopping is permitted, which can support your lorry and allows you to stop, get out and move off again safely. Check the slope, soft edges, ground strength and space for the load body and overhang.
  • Signal in good time, slow down progressively and watch behind you and along the side you are approaching. The rules on permitted places and positioning for stopping or parking are covered in “Manoeuvres with your lorry”. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).

22Secure your lorry on a slope

A light truck is parked uphill beside the right-hand kerb, with orange wheel chocks against the downhill side of its wheels.
The key idea

Before leaving your seat on a slope, secure your lorry against movement.

Remember

  • Check that it stays still before you get out.

Exam trap: Wrong: get out on a slope without checking your lorry stays still. Right: secure it against any movement before leaving your seat, and check it stays still before getting out.

Read the full explanation
  • Before leaving your driving position on a slope, secure the lorry against any movement and check that it remains stationary before getting out. [RGC, art. 92.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).

23Breakdowns and V-16 warning

A light truck is stopped on the right shoulder with an illuminated V-16 beacon on top of its cargo box, with nothing obstructing its light.
The key idea

If your lorry breaks down, keep control and prepare to place your beacon safely.

Remember

  • Keep control of your lorry and avoid sudden manoeuvres.
  • Decide where you can stop safely.
  • Before your journey, prepare an accessible place for your V-16.
  • Check where you can place it with its light visible.
  • Check that your cab, load body and load do not hide its light.
  • For warnings and occupant protection, see “Accidents, breakdowns and first aid”.

Exam trap: Wrong: improvise a climb onto your load body beside traffic. Right: before travelling, check where you can place your V-16 without your cab, load body or load hiding its light.

Read the full explanation
  • If a breakdown occurs, keep control of the lorry and avoid sudden manoeuvres while choosing where to bring it to a safe stop. [RGC, art. 130](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130).
  • Before your journey, choose an accessible location for the V-16, taking into account the height of the cab and load body. Check where you can place it from and whether the bodywork or load could obscure its light; avoid improvising a climb onto the load body beside traffic. [RGV, annex XI, signal V-16.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • Check the procedure for giving a warning and protecting the occupants in “Accidents, breakdowns and first aid”.

24Stopping inside a tunnel

A light truck is stopped at the right edge of a tunnel with its hazard lights and warning beacon on, while two occupants walk along the protected pedestrian area towards a refuge.
The key idea

If stopped in a tunnel, always switch off the engine, even at the wheel.

two minutesLonger wait: position lights on

Remember

  • If you stop in a tunnel, always switch off the engine.
  • Switch it off even if you stay at the wheel.
  • If you wait more than two minutes, keep it off until moving off.
  • Keep the position lights on during that wait.

Exam trap: Wrong: wait two minutes before switching off the engine. Right: switch it off whenever you stop in a tunnel; if you wait more than two minutes, keep it off until you move off and keep the position lights on.

Read the full explanation
  • If you are stopped inside a tunnel, always switch off the engine, even if you remain at the wheel; if the wait lasts more than two minutes, keep the engine off until you move off again and keep the position lights on. [RGC, art. 115.1 and 2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a115).

25Where to find more on securing your lorry and responding to emergencies

A light truck is stopped beside the kerb with an amber beacon lit on the cab roof, while the driver wearing a reflective vest speaks on the phone from the pavement.
The key idea

Use the named sections for slope security and tunnel stops.

Remember

  • When requesting assistance, describe the slope and clear space around your lorry.
  • Agree how helpers can approach without moving your lorry before securing it.
  • For slopes, see “Secure your lorry on a slope” in “Manoeuvres with your lorry”.
  • For your tunnel stop’s cause, see “Breakdowns, fires and traffic queues in tunnels”.
  • Find that section in “Accidents, breakdowns and first aid”.

Exam trap: Wrong: look for every procedure in this module. Right: for slopes, consult “Manoeuvres with your lorry”; for tunnels, consult “Accidents, breakdowns and first aid”.

Read the full explanation
  • When you request assistance, describe the slope at the location and the free space around your lorry; agree on an approach that allows work to take place without moving the vehicle before securing it.
  • To follow the full procedure for securing your lorry on a slope, consult “Secure your lorry on a slope” in “Manoeuvres with your lorry”; to respond according to the cause of a stop in a tunnel, consult “Breakdowns, fires and traffic queues in tunnels” in “Accidents, breakdowns and first aid”.

Turning while controlling the entire swept path

Check clearance on the inside, outside and above before and during the turn.

  1. Slow down before the turn and check the road you are turning into, pedestrians and both sides.
  2. Anticipate the rear wheels cutting in and the overhang swinging outwards.
  3. Signal and use only the space you can occupy while respecting priority rules.
  4. Turn slowly, alternating between looking ahead and checking your mirrors.
  5. Stop if a road user enters the danger zone or you are no longer certain you have enough space.

Reversing with a guide

Make sure the manoeuvre is permitted and maintain continuous communication.

  1. Confirm that reversing is permitted and determine the minimum distance necessary.
  2. Inspect your surroundings and agree on the path and signals with a person standing outside the swept path.
  3. Check that you can see the guide, warn others of the manoeuvre and reverse slowly.
  4. Watch both sides and the front swinging sideways, as well as the rear.
  5. Stop if you lose sight of the guide, receive unclear signals or encounter any danger.
  6. When you finish, secure the lorry before allowing workers to approach.

Immobilising and protecting your lorry

Secure the vehicle and protect its occupants according to the location and cause.

  1. Find a safe place where stopping is permitted; if you break down, move the lorry as far out of the way as possible without worsening the fault.
  2. Apply the parking brake, select the appropriate gear or transmission position and take additional measures to secure the lorry on a significant slope.
  3. If you break down, switch on the hazard warning lights and the connected V-16; keep the position lights and end-outline marker lamps on when required.
  4. Place the beacon in an accessible, visible location outside the vehicle without exposing yourself to traffic.
  5. Assess whether to move to a safe place off the road platform or remain inside with your seat belt fastened if getting out is dangerous.
  6. In a tunnel, distinguish between a traffic queue, a breakdown and a fire, and follow the specific procedure.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1On a long downhill section in a truck, it is advisable to:
2What are the basic principles on which the driving technique is based?
3While driving a C1 or C truck, continuous observation of the surroundings:
4Before changing lane or starting a maneuver with a truck, it is advisable to:

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module