Theory · D+E Licence - Bus with Trailer · Module 11 of 13

Maintenance and inspection of the vehicle combination

You learn to inspect the coach and its trailer, identify defects in tyres, brakes, connections and visibility equipment, and decide when you must immobilise the combination. You distinguish daily maintenance from ITV (vehicle roadworthiness test) obligations and answer exam questions using the rules for a passenger vehicle combination with a trailer.

36 min read25 sectionsReviewed Nov 3, 2026
A person wearing a reflective vest inspects the coupling of a green coach with an orange trailer parked in a service area.
Inspecting the coach and its trailer

1Check both parts of the combination

A driver wearing a reflective vest inspects the coupling between a coach and its trailer, parked and immobilized with wheel chocks.
The key idea

Check the bus and trailer before you set off.

Remember

  • Check the exterior, driving position and operation before joining traffic.
  • Check every trailer you have just collected too.
  • Keep the combination immobilised during checks.
  • Make sure nobody can move it or operate its mechanisms.
  • Never go underneath when air suspension alone supports it.
  • Correct dangerous defects before driving.

Exam trap: Wrong: you can drive with a dangerous defect on short journeys. Right: correct it before driving.

Read the full explanation
  • Before setting off, walk around the bus and trailer and inspect them visually. Always follow a set order so that the inner wheels, side lights or connections are not missed; whenever you change trailers, also check the one you have just collected.
  • Organise the inspection in three stages: surroundings and exterior, driving position, and functional checks before joining traffic. Check the tyres, steering, brakes, coupling and trailer systems.
  • Keep the combination immobilised during the checks. Before going near a wheel, the supports or the coupling, make sure nobody can move it or operate its mechanisms; never go underneath the bus or trailer when it is supported only by air suspension that could lower.
  • Distinguish between checks you can make as the driver and specialist repairs. If you find a defect that compromises safety, you must have it resolved before driving; a short route, a dry road or an empty bus does not make a defective trailer safe.

2Exterior and cab inspection

A driver inspects the coupling between a green coach and its orange luggage trailer, parked beside the right-hand kerb.
The key idea

Check the exterior, cab and passenger safety.

Remember

  • Look for fresh stains without touching hot parts or tasting fluids.
  • Check both sides, the rear and retracted supports.
  • Check you can reach the controls and see clearly.
  • Check luggage catches and restraints; luggage must not cover lights or plates.
  • Check doors, seat belts and access to emergency exits.
  • Before moving, check passengers are positioned, boarding and alighting finished, and doors closed.

Exam trap: Wrong: checking doors and passengers is enough. Right: also check the trailer and coupling.

Read the full explanation
  • Start by looking at the ground: a fresh stain may indicate a leak of oil, fuel, coolant or fluid from another system. Find its source without touching hot parts or tasting the fluid; distinguish air-conditioning condensate from a mechanical leak.
  • Walk around both sides and the rear. Look for loose parts, doors that are not properly closed, damage to bumpers, mudflaps or guards, and check that the support legs and moving parts are in their travel position; checking only the front leaves much of the combination unchecked.
  • From your driving position, check that you can reach the controls comfortably and see the instruments. Stow tools and other items in their designated places, and make sure passengers and objects do not restrict your view or movement. [RGC, art. 18](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a18).
  • When checking the luggage compartments and luggage trailer, check the fastenings, make sure nothing has come loose, and ensure no accessory or item of luggage obscures lights, number plates or your view. Poor distribution can affect stability even when everything fits: look for movement, leaning or damaged restraints and ensure these are corrected. The distribution and restraint of luggage are covered in Safe luggage and loads. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • Check that the doors, their warning devices and emergency controls work, and inspect the condition of steps, handholds, seats and any seat belts fitted to the bus. Keep emergency exits accessible and check that their opening devices and the required safety equipment are present and appear to be in good condition. These checks cover the passenger-specific items inspected under [RD 920/2017, Annex I, section 9](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#ai).
  • Before moving the bus, check that passengers are in the designated places and that no loose luggage could fall, be dragged along or cause avoidable inconvenience. Check the doors and gangways, but do not limit your inspection to them: you must also check the trailer and its connection. The seating of people is governed by [RGC, art. 10](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a10). Before moving off or resuming your journey, check that boarding and alighting have finished and that the doors are properly closed. [RGC, art. 11](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a11).

3Tyre pressures

A mechanic checks the pressure of a tire on a bus with a trailer parked beside the curb using a pressure gauge connected to the valve.
The key idea

Measure tyre pressures cold, using the specified pressure for your load and wheel arrangement.

Remember

  • Use a suitable pressure gauge; looking or striking the tyre is not enough.
  • Check the manufacturer’s pressure for each axle and load.
  • Do not deflate hot tyres to reach the specified cold pressure.
  • Check valves, caps and inner-wheel valve extensions.
  • Check your spare wheel too, if you carry one.
  • Do not replace inspection with the tyre pressure monitoring system.

Exam trap: Wrong: deflate hot tyres to the cold pressure. Right: pressure could become insufficient when they cool.

Read the full explanation
  • You must check the pressure regularly with a suitable pressure gauge; you cannot determine it accurately by looking at the bulge in the sidewall or striking the tyre. The regulatory pressure check is set out in [RGV, Annex VII.6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Measure it when the tyres are cold and use the pressure specified by the manufacturer for the load and fitment on each axle. There is no single pressure that is right for all buses, trailers or twin wheels; check the vehicle and tyre information, including after the load conditions change.
  • As you drive, the temperature rises and the pressure may increase. Do not deflate a hot tyre to bring it down to the cold pressure value: when it cools, it may be underinflated; if you suspect a problem, check it in accordance with the manufacturer's procedure.
  • Also check the valves, caps and extensions on the inner wheels, and the spare wheel if you carry one. A tyre pressure monitoring system helps detect pressure loss, but it does not replace checks for cuts and deformation or manual checks when required by the maintenance schedule.

4Incorrect pressure and wear

A mechanic checks the pressure of a tyre with a pressure gauge on a green coach with an orange trailer, stopped beside the kerb at a workshop.
The key idea

Keep tyre pressures correct to prevent overheating and abnormal wear.

Tyre pressurePossible effect
InsufficientMore heat, fuel use and risk of failure
ExcessiveAbnormal wear and a changed contact patch

Remember

  • With low pressure, you increase heating and fuel use.
  • With excessive pressure, you can cause abnormal wear.
  • Check the whole tread.
  • Do not assume the wear pattern proves a single cause.
  • If pressure drops again, ask for the leak to be found.

Exam trap: Wrong: lower pressure prevents blowouts. Right: insufficient pressure increases the risk of failure.

Read the full explanation
  • If you drive with insufficient pressure, the tyre deforms more, heats up and is more likely to fail. Rolling resistance and fuel consumption also increase; lowering the pressure is neither a way to save fuel nor protection against a blowout.
  • Excessive pressure does not automatically improve safety either. It can alter the contact patch and lead to abnormal wear; find the correct value for your fitment and load, rather than using the highest pressure allowed by the inflation equipment or the pressure another driver uses on a different vehicle.
  • Observe how wear is distributed across the tread. Pronounced wear on the shoulders, in the centre or on one side helps guide the inspection, but does not by itself establish the cause: pressure, alignment, suspension or operating conditions may all be factors.
  • Do not wait until a long journey to correct an incorrect pressure. If pressure drops again after inflation, have the leak located; repeatedly adding air without checking the valve, rim and tyre leaves the problem unresolved and may conceal internal damage.

5Minimum tread depth by category

A maintenance worker uses a tread depth gauge to measure the main grooves of a tyre on a heavy trailer coupled to a bus parked beside the right-hand kerb.
The key idea

Check the minimum tread depth for each vehicle’s category.

1.0 mmMinimum: M2, M3 bus
1.6 mmO2 trailer minimum
Vehicle and categoryMinimum tread depth
M2 or M3 bus1.0 mm
O2 trailer1.6 mm

Remember

  • Check each vehicle’s category in its documents.
  • Measure the main grooves with a suitable instrument in different areas around the tyre.
  • Deeper tread elsewhere cannot compensate for a badly worn area.
  • In rain, do not rely only on meeting the legal minimum.

Exam trap: Wrong: use the same minimum throughout the combination. Right: check each vehicle’s category.

Read the full explanation
  • For an M2 or M3 category bus, you must maintain at least 1.0 mm in the main grooves throughout its use on public roads. [RGV, Annex VII.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • If your bus tows an O2 category trailer, its tyres must have a minimum tread depth of 1.6 mm. A D+E licence does not change its technical category: identify each vehicle from its documents and apply the relevant minimum. [RGV, Annex VII.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Measure the tread in the main grooves with a suitable gauge and examine different parts of the circumference. A less worn area does not make up for the most worn part; a quick look at the outer side may miss wear on the inner shoulder or localised damage.
  • Do not treat the legal minimum as a guarantee of sufficient grip in all rain. You must take account of water, the condition of the tyre and the behaviour of the combination; a damaged tyre impairs steering and braking, and does not gain better properties because it is fitted to a heavy vehicle.

6Tyres, rims and fixings

A mechanic examines a cut with exposed cords in the front tyre of a coach with a trailer stopped beside the right-hand kerb.
The key idea

Check tyre damage, fixings and suitability for your vehicle.

3.5 tRegrooving: MMA must exceed this
Tyre operationWhat it does
RetreadingRenews the tread
RegroovingDeepens tread designed for this

Remember

  • Look for bulges, cuts, deep cracks and exposed cords.
  • Do not drive with structural tyre damage, even with enough tread.
  • Check rims and nuts; follow the manufacturer’s tightening instructions.
  • Check approved sizes, load, speed rating and single or twin fitting.
  • Have specialists carry out regrooving and follow its conditions.
  • For wheel changes, immobilise both units; use firm, level ground and suitable equipment.

Exam trap: Wrong: you can regroove any tyre. Right: only on vehicles over 3.5 t MMA, with tyres marked Regroovable or bearing the regulatory symbol.

Read the full explanation
  • Examine the tread and sidewalls for bulges, cuts, deep cracks, separations or visible cords. You must not drive with abnormal deformation or structural damage; adequate tread depth does not make up for a damaged casing. [RGV, Annex VII.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Visually check the rims and fixings: a missing nut, crack or sign of movement requires inspection. After removing a wheel, follow the manufacturer's tightening torque, sequence and subsequent check. If you need to change a wheel, choose firm, level ground, immobilise both vehicles and use chocks, a jack and tools suitable for their mass. Place the jack at the point specified by the manufacturer and check the equipment's capacity before raising the vehicle; keep passengers away from the work and request assistance if the surroundings or available equipment make it unsafe to proceed.
  • You must fit sizes and characteristics approved for the vehicle or permitted equivalents. Check the load index, suitability for single or twin fitment and the speed rating; a tyre that physically fits the rim is not necessarily suitable. [RGV, Annex VII.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Distinguish retreading from regrooving: one renews the tread, while the other deepens the tread pattern designed for that purpose. Regrooving is permitted only on vehicles with a gross vehicle weight (MMA) over 3.5 t and on tyres marked Regroovable or bearing the regulatory symbol; have the work done by specialists. [RGV, Annex VII.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).

7Check twin wheels

A technician uses a pressure gauge to check the inner dual tire of a bus with a trailer parked beside the right-hand curb.
The key idea

Check both twin tyres, including the inner tyre.

Remember

  • Measure the inner tyre’s pressure too, using suitable equipment.
  • Check compatible sizes and the same specified pressure for that arrangement.
  • Avoid large differences in wear or diameter.
  • Look for trapped objects and check the sidewalls do not touch.
  • Request safe specialist help for trapped stones, deformation or tyres previously run flat.
  • Do not strike or dismantle the loaded assembly during inspection.

Exam trap: Wrong: keep driving because the outer twin tyre holds air. Right: you may overload the sound tyre.

Read the full explanation
  • With a twin-wheel assembly, you must check both tyres, including the inner one. The outer tyre may look normal while the other loses air; the sound wheel then carries additional strain, and you cannot continue indefinitely with the twin wheel deflated.
  • Check that paired tyres are compatible in size and have the same prescribed pressure for that assembly. Avoid significant differences in wear or effective diameter: if they do not work in a similar way, the load is distributed unevenly between them and their deterioration increases.
  • Look at the gap between the wheels for stones or other trapped objects. The specified clearance must be maintained without the sidewalls rubbing; low pressure or overloading can cause this contact and make it harder to dissipate heat, even though from outside you can see only one tyre.
  • Use suitable access equipment to measure the inner tyre pressure and check the valve. If you find a trapped stone, deformation or a tyre that has been run deflated, arrange safe work: do not strike or dismantle the loaded assembly as part of a routine check.

8Chains and winter equipment

A green coach towing an orange trailer travels along a road surrounded by snow, with snow chains on the visible wheel of its rear drive axle and no chains on the trailer wheels.
The key idea

Fit chains to driven wheels and check the markings on special tyres.

3,500 kgWinter restriction rule: MMA above
Special tyresComplete marking
SnowM+S, M&S or M.S together with 3PMSF
Professional off-roadM+S, M&S or M.S together with POR

Remember

  • When chains are required, fit at least one driven wheel on each side.
  • Alternatively, use special tyres that meet the regulations.
  • For winter restrictions above 3,500 kg MMA, check the required tyre certifications.
  • In that case, equip at least the steering axle and driven axles.
  • Before travelling, check chain size, condition and fitting instructions.
  • Do not pass a road closure because you carry chains.

Exam trap: Wrong: M+S alone meets every winter restriction. Right: check the complete markings and required axles.

Read the full explanation
  • When it is compulsory or recommended to use chains or other authorised anti-skid devices, you must fit them to at least one driven wheel on each side, or use special tyres in accordance with the regulations. Identify the axles that transmit power: trailer wheels are not driven simply because they carry a load. [RGV, art. 12.5.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • To comply with winter mobility restrictions with a vehicle whose MMA (maximum authorised mass) exceeds 3,500 kg, you must fit 3PMSF or POR certified tyres at least on the steering axle and driven axles. Check the full markings required on the sidewall; do not assume that any deep tread makes a tyre a special tyre. [RGV, Annex VII.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Special snow tyres carry the M+S, M&S or M.S marking together with 3PMSF; tyres for professional off-road use carry that marking together with POR. Check these identifications on the sidewall when preparing the vehicle for a winter restriction. [RGV, Annex VII.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Before the journey, check that the devices fit the wheel size, are undamaged and can be fitted according to their instructions. Practise in a safe place, check their tension when the manufacturer specifies and follow their conditions of use; carrying chains does not authorise you to pass a road closure.

9Engine oil and lubrication

A mechanic checks the oil dipstick beside the open engine compartment of a bus with a trailer parked on a level surface beside the right-hand kerb.
The key idea

Check the oil level and act on oil pressure warnings.

Oil checkWhat it tells you
LevelQuantity available
PressureLubricant circulation

Remember

  • Check on level ground with the engine stopped.
  • Follow the manufacturer’s temperature and waiting time instructions.
  • Do not exceed the maximum mark when topping up.
  • Use the specified oil; request diagnosis if you frequently need to top up.
  • For an oil pressure warning while running, stop safely and switch off the engine.
  • Change oil and filter as scheduled; topping up does not replace changing oil.

Exam trap: Wrong: having oil guarantees pressure. Right: you can have enough oil but lose pressure.

Read the full explanation
  • Check the oil level with the combination on level ground and the engine switched off, following the temperature and waiting time specified by the manufacturer. Use the dipstick or designated electronic check and make sure the result is within the level marks, without exceeding the maximum.
  • The level indicates the amount available; the pressure warning concerns oil circulation. There may be oil in the sump while pressure is being lost: if that warning appears while the engine is running, stop safely and switch off the engine to prevent damage.
  • When topping up, use oil with the required specifications and add measured amounts. Do not mix products because they share a colour or trade name; if you need to top up frequently or notice stains, unusual consumption or contaminated oil, arrange a diagnosis to find the cause.
  • Follow the manufacturer's oil and filter change schedule, adapted to the bus's service. Topping up does not replace changing degraded oil or a saturated filter; record the work so that a top-up is not mistaken for a full service.

10Cooling and temperature

A maintenance worker checks the coolant level in an expansion tank with its cap closed beside a coach with a trailer parked along the right-hand kerb of a stopping area.
The key idea

Check coolant cold and stop for a serious temperature alarm.

Remember

  • Check the expansion tank level with the engine cold.
  • Look for leaks in hoses, connections and the radiator.
  • Do not open a hot cooling system’s cap: you could be scalded.
  • Keep your hands away from the fan; it may start automatically.
  • Use the specified coolant and concentration.
  • If temperature leaves its normal range, stop safely and follow instructions.

Exam trap: Wrong: keep topping up without investigating. Right: repeated level drops need investigation.

Read the full explanation
  • Check the coolant with the engine cold and check the level in the expansion tank. Inspect hoses, joints and the radiator for leaks or deterioration; a repeated drop requires investigation, even if you can temporarily restore the level by adding the correct product.
  • Do not open the cap on a hot system: pressurised liquid can escape suddenly and burn you. Wait for it to cool and follow the safety instructions; also keep your hands away from a fan that may start automatically, even when the vehicle is stationary.
  • Use the specified coolant and follow the requirements for its concentration and replacement. Its functions include controlling temperature and protecting the system; do not treat it as a tank into which you can add any water or product without checking compatibility, especially when preparing the bus for severe cold.
  • If the temperature rises outside its normal range or a serious warning appears, find a safe place to stop and follow the manufacturer's procedure. Continuing to demand power can worsen the damage; the warning light alone does not tell you whether the level, ventilation, pump or another component has failed.

11Other levels, tanks and filters

A maintenance worker adds AdBlue through a dedicated blue filler beside the closed diesel cap on a bus with a trailer parked by the right-hand kerb.
The key idea

Check fluids and filters according to the equipment fitted.

Remember

  • Check you have enough fuel and the tanks are closed.
  • If you use AdBlue, use its own filler and the correct product.
  • Identify the installed systems before checking their levels.
  • Check filters according to maintenance instructions and warnings.
  • Do not bypass filters or fuses to hide problems.
  • Check tanks, batteries and covers are secure and undamaged.

Exam trap: Wrong: put AdBlue in diesel or replace it with water. Right: use its designated filler and product.

Read the full explanation
  • Check that there is enough fuel and that the tanks are closed. If the bus uses AdBlue, check its level and top it up only through the correct filler: it is a product used for exhaust-gas treatment, and you must not put it in the diesel tank or replace it with water.
  • Check any hydraulic systems fitted to the vehicle, such as power steering or auxiliary mechanisms, in accordance with their instructions. A combination with air brakes is not checked by looking for a brake-fluid reservoir as though all its brakes were hydraulic; first identify the system fitted.
  • Check air, fuel and other filters according to the maintenance schedule and the vehicle's indicators. If there is a restriction or contamination warning, arrange the specified work; do not remove or disable a filter to clear the symptom so that you can complete the journey.
  • Check that tanks, batteries and caps are secure and have no visible leaks or damage. Follow the manufacturer's electrical procedure and do not bridge fuses or handle terminals without proper training; an improvised repair can cut power to the lights, brake units or other essential services.

12Lights on the towing vehicle and trailer

A worker wearing a reflective vest checks the illuminated rear lights of a trailer attached to a bus parked in a maintenance area from outside the vehicle.
The key idea

Check the bus and trailer lights from outside.

Remember

  • Check actual operation with assistance or the designated checking system.
  • Check position, brake, indicator, hazard, rear fog and number plate lights.
  • Also check the required end-outline and side marker lights.
  • Keep lights and reflectors clean, secure and unobstructed.
  • Every non-agricultural trailer must have indicators with a hazard warning function.
  • If several trailer lights fail, check the connector safely.

Exam trap: Wrong: the bus dashboard proves the trailer lights work. Right: check their actual operation.

Read the full explanation
  • You must check that the lights actually work from outside, with assistance or through the checking system fitted to the bus. A warning light on the bus dashboard does not by itself prove that the lights on the last vehicle in the combination are working.
  • Include position lights, brake lights, indicators, hazard warning lights, rear fog lights, number plate lights, and the end-outline marker lamps and side lights that apply. Every non-agricultural trailer must have indicators with hazard warning lights, regardless of its MMA. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • Also check the light units, reflectors and reflective surfaces: they must be clean, secure and undamaged so that their effectiveness is not reduced. When checking a long vehicle, walk along both sides; a dirty light or one covered by an accessory may fail to do its job even if its bulb remains lit.
  • If several trailer lights fail at the same time, check the connector safely and report the fault. Do not substitute switching on the interior light for a check, or disconnect warnings to hide the fault; required equipment is covered in the Safety devices on a bus and trailer module.

13Mirrors, windows and windscreen wipers

A green coach with an orange trailer stands beside the kerb while the windscreen washers spray water onto the glass and the wipers clean it.
The key idea

Keep the equipment you need for vision clean and correctly adjusted.

Remember

  • Adjust your seat, then mirrors, with the vehicle stationary.
  • Check fitted mirrors, cameras and screens for security, cleanliness and clear views.
  • Test the washers and check wiper blade condition.
  • Check demisting; remove ice and dirt without damaging the glass.
  • Do not operate wipers frozen to the glass.
  • If you lose visibility, stop safely and restore it before continuing.

Exam trap: Wrong: washer fluid guarantees effective cleaning. Right: also check the jets and wiper rubber.

Read the full explanation
  • Adjust the seat and then the mirrors while the vehicle is stationary. Check that they are secure and clean and provide a clear field of vision, including devices that let you monitor areas near the cab and along the sides; a poorly adjusted mirror does not improve your control of the trailer on bends.
  • You must maintain a useful view through the windows and using indirect-vision devices. Also check cameras and screens when they form part of the equipment. The technical requirements for glazing, mirrors, windscreen wipers and washers are set out in the [RGV, art. 11](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).
  • Operate the windscreen washer and check that the jets reach the swept area. Check the fluid level, pipes and wiper blades: if they leave streaks, judder or spread dirt, they need cleaning or replacing; carrying washer fluid does not guarantee visibility if the rubber is worn. [RGV, art. 11.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).
  • Check the demisting system and remove ice or dirt without damaging the windows or rubber seals. Use fluid suitable for the ambient temperature and avoid operating wipers frozen to the glass; if you lose visibility while driving, you must find a safe place to stop and restore it before continuing.

14Steering, suspension and chassis

A mechanic uses a flashlight to inspect the suspension of a trailer attached to a bus stopped beside a kerb in a Mediterranean setting.
The key idea

Identify steering, suspension and structural faults before driving.

Remember

  • Request inspection for steering play, pulling, abnormal resistance or vibration.
  • Look for leaning, broken parts and air suspension leaks.
  • Before moving off, check the specified driving height.
  • Correct tyre pressures cannot compensate for damaged suspension.
  • Stop using the vehicle if a crack could affect strength or the coupling.

Exam trap: Wrong: a sound bus compensates for faulty trailer suspension. Right: check both parts.

Read the full explanation
  • Check for play, unusual resistance, pulling or vibration in the steering. Do not dismiss these as mere discomfort: the steering keeps you on course, and a fault can compromise control even when you are travelling slowly or on a road you know well.
  • Check whether the combination is leaning, whether any suspension components are broken or whether an air spring is losing air. Before setting off, check that the air suspension reaches the intended driving height; the setting used for loading or coupling may not be suitable for driving.
  • The suspension and shock absorbers help keep the wheels in contact with the road. Wear can impair stability and braking; correctly inflated tyres cannot compensate for damaged suspension, just as a bus in good condition cannot correct defects in the trailer.
  • Look for visible damage to the chassis, cross-members and coupling supports, especially after an impact or a manoeuvre involving contact. Do not try to diagnose a structural crack by its apparent size; stop using the vehicle and seek a technical assessment if it could affect strength or the connection.

15Coupling and supports: mechanical inspection

A crouching mechanic checks the coupling safety lock between a green coach and an orange trailer secured with a wheel chock on a paved area.
The key idea

Check the coupling lock and retract supports before driving.

Remember

  • Check compatibility, fixings, closure and the device preventing accidental opening.
  • Look for wear, cracks and abnormal play.
  • If a pull test is required, follow instructions and also check closure visually.
  • Lubricate only the points specified for your model.
  • For driving, retract and lock the jockey wheel or supports.
  • Before uncoupling, immobilise the trailer and support it on suitable ground.

Exam trap: Wrong: grease every coupling surface. Right: some friction surfaces must remain grease-free.

Read the full explanation
  • Check that the connections are compatible and that the coupling closes securely. The coupling must have a device that prevents it from opening unintentionally; bringing the parts together or assuming the mechanism is closed because you hear contact is not enough. [RGV, art. 13.1 and 13.3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • At the coupling between the bus and the trailer drawbar, inspect the fixings to the chassis, the appropriate coupling head or towing eye, the closing mechanism and its safety device. Look for wear, cracks and abnormal play, following the manufacturer's inspection points. If a pull test is required, carry it out according to the procedure for the combination and also check the closure visually; the fact that the bus can pull the trailer does not by itself prove that the safety device works.
  • Clean and lubricate only the points specified for your model. There is no universal interval for greasing every coupling head: some friction stabiliser surfaces must be kept free of grease, while other couplings need lubrication; always follow the instructions for the mechanism actually fitted.
  • Check the jockey wheel or other supports fitted to the trailer, including their handles, fixings and safety devices. They must be retracted and locked for driving; before uncoupling, immobilise the trailer and make sure it is supported on suitable ground. Centring the luggage does not prevent the trailer from tipping or moving when you separate it from the bus.

16Connections and breakaway devices

A worker inspects the red and yellow pneumatic connections and the electrical cable between a green bus parked beside the kerb and its orange trailer.
The key idea

Check the connections and safety devices fitted to your trailer.

1,500 kgConditional secondary coupling: maximum MMA
Trailer brake systemWhat you check
Usual two-line air systemRed: supply; yellow: brake control
Overrun brakeSliding head, protection and linkages

Remember

  • Look for chafing, cracks, unsafe joints and loose connectors.
  • Leave room for turning, without cables becoming taut or dragging.
  • Check leaks and connections for the brake system fitted.
  • Distinguish automatic braking on separation from a secondary coupling.
  • Up to 1,500 kg MMA, require secondary coupling without automatic braking on coupling failure.

Exam trap: Wrong: look for air pipes on every trailer. Right: identify its braking system first.

Read the full explanation
  • Inspect the flexible air lines and electrical cables throughout the accessible area. Look for chafing, cracks, insecure joints and loose connectors; they must have enough freedom to articulate without becoming taut, dragging or catching on parts of the bus or trailer.
  • If your trailer has the usual two-line air-braking system, identify the red supply line and the yellow brake-control line. Check their markings and couplings and make sure there are no leaks; also check the electrical connection for the braking system where fitted. If it has an overrun brake, inspect the sliding coupling head, its guard and the linkages according to the manufacturer: do not look for air lines on a trailer that does not use that system.
  • Distinguish a device that applies the brakes when the coupling separates from the secondary coupling that retains some residual steering and prevents the drawbar from touching the ground. The latter is required on trailers with a maximum authorised mass (MMA) of up to 1,500 kg that do not have a breakaway braking system. [RGV, art. 13.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Check the devices required for the particular trailer and do not substitute one for another because they look like a cable or chain. The full connection and disconnection sequence is covered in Safe coupling and uncoupling; during maintenance, you must identify damage, incompatibility and insecure locking.

17What you must check on the brakes

A green coach towing an orange trailer has its brake lights illuminated on a flat, dry road, with both vehicles aligned in the right-hand lane.
The key idea

Check that the combination brakes correctly and stays immobilised.

BrakeFunction you check
ServiceSlows or stops you while driving
ParkingKeeps the vehicle immobilised
SecondaryStops the vehicle if service braking fails

Remember

  • Include the trailer when checking the brakes.
  • Test at very low speed in a safe, clear area.
  • Check braking is progressive, without abnormal pulling.
  • Request inspection for delayed response, new noises or brakes remaining applied.
  • Check on level ground and dry surfaces too.
  • If you have overrun brakes, do not lock the mechanism to hide faults.

Exam trap: Wrong: confuse the retarder with the secondary brake. Right: secondary braking stops you if service braking fails.

Read the full explanation
  • Check that the service brake responds and that the parking brake immobilises the vehicle, including the trailer. The secondary brake lets you stop the vehicle if the service brake fails; do not confuse these functions with the retarder. [RGV, Annex VIII.1.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anviii).
  • Check accessible wear, pipes and possible contamination of friction components. Adjustments and repairs to discs, drums, pads, brake shoes or chambers require the appropriate technical procedure; do not try to compensate for a defect by increasing tyre pressure or tightening parts by guesswork.
  • In a safe area with clear space, check at very low speed that the combination brakes progressively and without abnormal deviation. A delayed response, a wheel that remains braked, a new noise or an imbalance requires inspection before you join traffic.
  • The brakes must also work on level ground and on a dry surface. Do not leave the check until you are going downhill: with a heavy load, even a partial failure can affect stability and increase the distance you need to stop, even if the bus still seems to be braking.
  • On a trailer with an overrun brake, check that the actuating device and parking brake show no signs of seizing or visible damage. Do not lock the mechanism to hide jolts or noises. The classification and detailed operation of each system are covered in Trailer and combination braking; here, you must recognise their condition and make sure the fitted equipment works.

18Building up and monitoring air pressure

A driver checks the two air pressure gauges with the warning light on and a hand on the parking brake of a bus with a trailer stopped beside the kerb.
The key idea

With air brakes, wait for correct pressure before moving off.

Remember

  • Watch the circuit pressure gauges.
  • Wait for the specified operating range before releasing the immobilisation devices.
  • Check warnings clear according to the manufacturer’s instructions.
  • With the combination secured, listen for leaks and watch for abnormal pressure drops.
  • If pressure drops and the warning appears, find a safe place to stop.
  • Do not pump the pedal to recover air: you consume it.

Exam trap: Wrong: use another bus’s pressure as your reference. Right: follow the installed system’s values.

Read the full explanation
  • If the bus or trailer has air brakes, the compressor supplies air and the reservoirs store the energy needed to operate them. Monitor the circuit gauges and wait until they reach the specified operating range before releasing the immobilisation and moving off. Check the connections according to the braking system actually fitted to your trailer.
  • Check that low-pressure warnings go out as intended by the manufacturer. There is no single outlet-pressure figure that applies to all buses: use the references for the system fitted and do not treat the reading on another vehicle as normal for yours.
  • Listen for possible leaks while the combination is secured and watch for an abnormal drop in pressure. Low pressure, audible leaks or defective pressure recovery are among the items inspected on commercial vehicles; silencing the warning does not fix them. [RD 563/2017, Annex II, paragraph 1.1.3 a), b) and d)](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512).
  • If pressure drops during the journey and a warning comes on, find a safe place to stop before braking capacity is lost. Pumping the pedal uses air and does not repair a leak; nor should you rely on increasing engine speed to make it acceptable to continue with a faulty circuit.

19Reservoirs, air dryer and spring brakes

A bus with a trailer remains secured with wheel chocks in a lay-by beside a technician and a heavy-vehicle recovery truck.
The key idea

Maintain the air system and avoid handling spring brakes.

Remember

  • Check the air dryer and drains according to the installed equipment.
  • If drainage is automatic, check it works.
  • For manual draining, immobilise the combination and follow its instructions.
  • Request diagnosis if abnormal amounts of water or oil appear.
  • If low air leaves the brakes applied, request assistance equipped for heavy vehicles.
  • Do not dismantle spring brake chambers: dangerous energy can remain without air.

Exam trap: Wrong: disable spring brakes to finish the service. Right: request suitably equipped assistance.

Read the full explanation
  • Moisture in the air can condense in the reservoirs and damage the system. Check maintenance of the air dryer and drain valves according to the equipment fitted; if the drain is automatic, check that it works rather than assuming that it removes every need for inspection.
  • If the system requires manual draining, do it with the combination immobilised and in accordance with its instructions. Do not set a universal interval independent of the climate, air dryer or manufacturer; an abnormal amount of water or oil in the drained fluid means you must investigate the cause.
  • In spring brake actuators, mechanical energy holds or applies the brake, and air pressure releases it, depending on the design. If air pressure is lost, the vehicle may be braked; do not tow it or override its mechanisms to complete the service. Request assistance equipped to deal with heavy vehicles.
  • Do not dismantle spring brake chambers or handle their release mechanisms as part of a daily check. They can retain dangerous energy even without air pressure; recovery work requires competent personnel and measures to ensure that the bus and trailer cannot move.

20ABS, EBS and electronic control

A technician holding a diagnostic tablet inspects the plugged-in electronic connection between a coach and its trailer, parked beside a kerb.
The key idea

Understand electronic warnings and keep brake connections in good condition.

Remember

  • Check the self-diagnostic sequence using your model’s manual.
  • ABS helps prevent wheel lock, but does not create grip.
  • Keep tyres, sensors, cables and connections in good condition.
  • Check persistent warnings; identify whether they concern the bus or trailer.
  • For stop instructions, insufficient pressure or lost response, immobilise safely and request assistance.
  • Do not disconnect the electronic plug to extinguish a warning.

Exam trap: Wrong: every ABS warning means you have no brakes. Right: check the message and other symptoms.

Read the full explanation
  • Check the self-test sequence of the ABS warning lights and the combination’s electronic systems. Their behaviour depends on the model and may include checks when you start moving; consult the manual before treating an expected sequence as a fault or assuming that a persistent warning is normal.
  • ABS helps prevent the wheels from locking during braking; electronic control cannot create grip or correct a damaged tyre. Keep the tyres, sensors, wiring and connections in good condition, and leave yourself a safety margin even if the bus has advanced braking and stability assistance.
  • An ABS warning does not necessarily mean that all service braking has failed, but it tells you to investigate the fault. If it comes with an instruction to stop, insufficient pressure or loss of response, immobilise safely and request assistance before continuing.
  • Do not disconnect the trailer’s electronic system plug to switch off a warning. Record the message, identify whether it relates to the bus or trailer and report it to the workshop; diagnosis must check the affected vehicle, not just erase the fault code.

21Interpret dashboard warnings

The driver of a bus with a trailer stopped beside the right-hand kerb operates the ignition while looking at a red oil warning light on the dashboard.
The key idea

Read the specific dashboard warning and follow its instructions.

WarningWhat you must do
Insufficient oil pressureStop safely and switch off the engine
Brake air pressureStop safely and secure against movement
Electrical charging with engine runningAttend to the warning and request inspection

Remember

  • Check warning lights come on and go out as specified.
  • Read screen messages; colour only guides you.
  • For a serious alarm, stop safely and follow the relevant instructions.
  • Do not assume an amber warning lets you finish the route.
  • Note when warnings appear without distraction or operating screens while driving.

Exam trap: Wrong: ignore the charging warning because the engine runs. Right: attend to it and request inspection.

Read the full explanation
  • When you switch on the ignition, check that the warning lights perform the expected test and that the relevant warnings go out when the system is ready. Read the screen messages too: the colour indicates urgency, but the specific warning determines its meaning and the action you must take.
  • A serious oil, temperature or brake alarm means you must stop safely and follow the relevant instruction. If it indicates insufficient lubrication pressure, stop the engine after stopping the vehicle; if it concerns braking air pressure, also secure the combination against movement.
  • An electrical charge warning that stays on while the engine is running may indicate a generation or power supply problem. Deal with it and arrange an inspection: the engine continuing to run does not guarantee that the combination’s lights, control units and other electrical systems will keep working indefinitely.
  • Do not assume every amber warning lets you finish the route. Check its meaning, the symptoms and the manufacturer’s instructions; note when it appears, whether it changes as you drive and what other warnings accompany it, without operating screens or doing checks that distract you while driving.

22Noise, overheating and blowouts

A coach towing a trailer is stopped beside the right-hand kerb while smoke rises from a rear wheel and the driver makes a phone call away from it.
The key idea

Stop safely for dangerous symptoms and avoid sudden movements after a blowout.

Remember

  • Investigate abnormal noises or vibrations as soon as possible.
  • Find a safe place to stop if they may affect control.
  • Request inspection for smoke or abnormal wheel heating.
  • Do not touch hot parts or keep driving to cool them.
  • For a blowout, hold the steering firmly and reduce speed in a controlled way.
  • If heat reduces brake effectiveness, stop without creating a greater risk.

Exam trap: Wrong: brake harshly after a blowout. Right: avoid sudden braking or steering until you stop safely.

Read the full explanation
  • If abnormal noises or vibrations occur, investigate the cause as soon as possible. Reduce the demands on the vehicle and find a safe place to stop if they could affect control; accelerating through the vibration or waiting for it to disappear on its own leaves the fault unresolved.
  • A strong smell of brakes, smoke or abnormal heating of a wheel may indicate a binding brake, a bearing problem or another fault. Do not touch hot parts or keep driving to cool them; arrange an inspection and keep people away if there is a risk of fire or tyre failure.
  • If a tyre bursts, hold the steering wheel firmly, avoid sudden corrections and reduce speed in a controlled way until you can stop safely. Heavy braking or a sudden turn can destabilise the combination; also check for possible damage to the twin wheels, lines, bodywork and fastenings.
  • If the brakes lose effectiveness because of heat, treat it as a safety problem and stop where you can do so without creating a greater risk. Using the gears and engine braking on descents is covered in Driving techniques with a bus and trailer; cooling the system does not replace finding out why it overheated.

23Roadside breakdown: warn others and protect yourself

A coach with a luggage trailer is stopped on the shoulder with its hazard lights and a V-16 beacon illuminated, while a person wearing a reflective vest speaks on the phone behind the safety barrier.
The key idea

Warn others about your breakdown, protect yourself and request assistance.

Remember

  • Move the combination out of traffic lanes if you can safely.
  • For hazardous roadside immobilisation, use hazards, a connected V-16 and appropriate lighting.
  • Before departure, check your certified connected V-16 and reflective high-visibility vest.
  • Carry compulsory, approved, suitable fire-extinguishing equipment in working order.
  • Give your location, fault and vehicle type: bus with luggage trailer.
  • Avoid repairs beside traffic or underneath the vehicle in that environment.

Exam trap: Wrong: a spare wheel is always compulsory for this combination. Right: it is optional; if carried, check its condition and pressure.

Read the full explanation
  • If you break down, you must move the combination out of the traffic lanes if you can do so safely and signal that it is immobilised using the hazard warning lights, connected V-16 and any appropriate lighting; protection of occupants and use of the high-visibility vest are covered in “Responding to accidents and breakdowns” and “Safety devices on a bus and trailer”. [RGC, art. 130.2-4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130); [RGC, art. 118.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a118).
  • Request assistance and give your location, describe the breakdown and say that you are driving a bus with a luggage trailer. Avoid repairs beside traffic or underneath the vehicle in those conditions.
  • Before setting off, check that you carry a certified connected V-16, a high-visibility reflective vest and approved fire-extinguishing equipment that is suitable and ready for use: these are compulsory for your D+E combination. Check the beacon’s power supply and service expiry in accordance with its specifications. Check the condition and maintenance of the fire-extinguishing equipment. Annex XII.2 does not require a spare wheel for this combination; if you carry one, check its condition and pressure. [RGV, Annex XII.1.a-b and 2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii); [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).

24When you can resume driving

A mechanic checks the wheel of a chocked trailer attached to a stationary coach in a right-side lay-by while the driver waits beside him.
The key idea

Continue only when your combination is safe again.

TaskWhat you must do
Finding the causeGather symptoms, consult the manual and check related accessible components.
Minor repairsDo these only with suitable training and tools; follow instructions.
Brakes, structure or work beyond your capabilitiesRefer these to the workshop.

Remember

  • Check the cause is resolved and no associated damage remains.
  • Recheck parts affected by repairs.
  • For significant brake, steering, tyre or coupling defects, stay immobilised and request assistance.
  • If a fault unrepairable en route forces lower-intensity lighting, reduce speed.
  • You must then drive safely and stop within the illuminated area.
  • Report and record the fault; a temporary repair may need later inspection.

Exam trap: Wrong: a warning disappearing after restarting proves repair. Right: check the cause and safety before continuing.

Read the full explanation
  • Before continuing, check that the cause has been resolved and that there is no related damage. Recheck the wheels, locking, connections, supports and warnings if the work affected them; a warning light going out after you restart the ignition does not by itself prove that a repair has been made.
  • If an irreparable breakdown en route means you have to use lower-intensity lighting, reduce your speed so that you can stop within the illuminated area. This rule does not authorise you to drive without visibility or in unsafe conditions. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107).
  • If there are serious defects in the brakes, steering, tyres or mechanical coupling, keep the combination immobilised and arrange suitable assistance. A trailer with ineffective brakes is not safe just because the bus can tow it; do not improvise recovery using makeshift chains or cables either.
  • Report and record what happened so that it can be followed up. A temporary repair may require a later inspection, replacement parts or a technical check before the next service; keep the workshop’s information and distinguish between fixing the symptom and restoring the combination to a safe condition. To identify the cause, collect the symptoms, consult the manual and first check the accessible components related to them. Limit minor repairs to tasks for which you have the training and suitable tools, such as replacing a wiper blade in accordance with the instructions; refer brake circuits, structural components and work beyond your capabilities to a workshop.

25ITV (vehicle roadworthiness test) and maintenance between inspections

Two inspectors separately check the wheels of a green coach and its orange luggage trailer at a vehicle inspection station.
The key idea

Check each vehicle’s ITV and keep both safe between inspections.

five yearsBus ITV age threshold
ten yearsLuggage trailer ITV age threshold
two monthsMaximum defect correction deadline
Vehicle and categoryAnnual ITVSix-monthly ITVWhere you place the V-19 sticker
M2 or M3 busUp to five years oldOver five years oldInside, in the upper right-hand corner of the windscreen
O2 luggage trailer (not a caravan)Up to ten years oldOver ten years oldWithout a windscreen: somewhere clearly visible

Remember

  • Calculate age from the recorded first registration or entry into service.
  • Check the bus and trailer ITV separately.
  • Repair minor defects within two months; no repeat inspection is needed solely for them.
  • With an unfavourable result, drive only for repair or correction and return to ITV.
  • With a negative result, use other means to transport it from the station.
  • After unfavourable or negative results, return repaired within two months of the first result.

Exam trap: Wrong: use the trailer’s ten-year threshold for the bus. Right: bus ITV becomes six-monthly over five years.

Read the full explanation
  • You must check the bus’s ITV and the trailer’s ITV separately. For M2 and M3 buses, the periodic inspection is annual until they are five years old and every six months once they are more than five years old. For an O2 luggage trailer (not a caravan), it is annual until it is ten years old and every six months once it is more than ten years old. Calculate age from the date of first registration or recorded entry into service. [RD 920/2017, art. 6](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a6).
  • If the ITV result is a pass with minor defects, you must repair them within a maximum of two months; you do not need a new inspection solely because of those defects. If the result is unfavourable because of major defects, you may only drive the vehicle to a workshop or for rectification, and back to the ITV station; you must present it again within a maximum of two months from the first unfavourable result. If the result is negative because of very serious defects, the vehicle must be transported from the inspection station to its destination by means other than the vehicle itself, and you must present the repaired vehicle within a maximum of two months from the first negative result. [RD 920/2017, arts. 9 and 11](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a1-3).
  • Place the bus’s V-19 sticker inside the windscreen, in the upper right-hand corner; on a towed vehicle without a windscreen, place it somewhere clearly visible. Each sticker certifies its own vehicle. A pass does not remove your duty to keep the combination safe between inspections. [RGV, Annex XI, V-19](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-19).
  • Prepare for the inspection by checking known defects and keeping the report for maintenance purposes. Inspection intervals and documents are covered in Driver and vehicle combination documentation; commercial vehicles may also undergo roadside technical inspections, which can detect faults that develop even while your ITV is valid. [RD 563/2017, arts. 1 and 2](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512).

Daily walk-around before setting off

Walk around the combination in a consistent order and finish with a functional check.

  1. Immobilise the combination and check the ground, surroundings and for possible leaks.
  2. Walk along both sides and around the rear: tyres, inner tyres in twin-wheel assemblies, rims, lights, reflectors and loose parts.
  3. Check that the coupling is locked, the flexible hoses and connectors are in good condition, and the supports are in the travelling position.
  4. Check the levels in accordance with the manufacturer's instructions, and clean the windows, mirrors and light lenses.
  5. Adjust the seat and mirrors; check the windscreen wipers, washers and dashboard warnings.
  6. Wait for the correct air pressure and check the lights and brake response in a safe area.
  7. Resolve safety defects before joining the road and report any that require workshop attention.

Checking tyres and twin-wheel assemblies

Combine measurement with visual inspection; neither replaces the other.

  1. Identify the vehicle category, the permitted tyres and the prescribed pressure for its load and fitment.
  2. With the tyres cold, measure all pressures, including those of inner tyres, and check the valves and extensions.
  3. Measure the tread in the main grooves and examine the circumference and sidewalls.
  4. On twin-wheel assemblies, check matching, spacing and that no objects are trapped between the tyres.
  5. Check rims and fixings; arrange safe repairs if there is damage, repeated pressure loss or signs of looseness.

Low air pressure warning

Maintain control and ensure that the combination is immobilised.

  1. Before setting off, keep the combination immobilised until the system is within its operating range and has completed its checks.
  2. If the warning appears while driving, find a safe place to stop without continuing to consume air through unnecessary operation of the controls.
  3. Immobilise the coach and trailer and request assistance if there is a leak, pressure does not recover or the warning persists.
  4. Do not disable warning devices, spring brake chambers or connections to continue your journey.
  5. Resume only once the fault has been resolved and the response of the whole combination has been checked.

Checks after a repair

Check the condition of the combination before resuming your journey.

  1. Confirm that the cause of the fault has been resolved and check for associated damage.
  2. Check the wheels, coupling lock, connections and supports affected by the work.
  3. Check the dashboard warnings and the response of the repaired systems in accordance with the technical instructions.
  4. Record the work and any subsequent checks or inspections specified by the workshop.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1In a D1+E or D+E combination, passengers, load, and the trailer must be:
2A steering fault in a D1+E or D+E combination:
3In a passenger combination with a trailer it is important to inspect:
4If a warning appears in a D1+E or D+E combination indicating a major fault, the correct action is to:

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module