Theory · D1+E Licence - Minibus with Trailer · Module 11 of 13

Maintaining the minibus and its trailer

You learn to check the D1 minibus and its trailer, interpret fault warnings and maintain tyres, brakes, connections and visibility. You answer questions on routine maintenance, minor repairs and ITV (vehicle roadworthiness test) by linking each check to the safety of passengers and the combination.

38 min read29 sectionsReviewed Nov 3, 2026
A mechanic checks the tyre pressure of a green minibus with an orange trailer attached, parked beside the kerb in a roadside lay-by.
Minibus and trailer maintenance

1Check both parts of the combination

A driver visually inspects the coupling and connections between a minibus and its trailer, both immobilized with wheel chocks in a parking area.
The key idea

Check your minibus and trailer before setting off.

Remember

  • Always follow the same checking order.
  • Also check any trailer you have just collected.
  • Keep both vehicles secured against movement during checks.
  • Make sure nobody can operate mechanisms while you are nearby.
  • Never go under a vehicle with suspension that could lower.
  • Resolve dangerous defects before driving.

Exam trap: Wrong: you check only the minibus. Right: check the trailer too, even without passengers.

Read the full explanation
  • Before setting off, you must walk around and visually inspect the minibus and trailer. Always follow a set order so that you do not miss the inner wheels, side lights or connections; changing trailers also requires you to check the one you have just collected.
  • Organise your inspection in three stages: surroundings and exterior, driving position, and functional checks before joining traffic. Check tyres, steering, brakes, coupling and the towed vehicle’s service systems.
  • Keep the combination secured against movement during checks. Before approaching a wheel, the supports or the articulation point, make sure nobody can move it or operate its mechanisms; never go underneath a vehicle supported only by suspension that can lower.
  • Distinguish between observations you can make as a driver and specialist repairs. If you find a defect that compromises safety, you must resolve it before driving; a short route, a dry carriageway or driving the minibus without passengers does not make a defective towed vehicle safe.

2Exterior and cab inspection

A driver looks without touching at a dark stain on the ground beside a green minibus with an orange trailer parked next to the kerb on its right-hand side.
The key idea

Check outside and keep your cab and exits clear.

Remember

  • Look for fresh stains under the vehicle.
  • Distinguish air-conditioning water from a leak.
  • Retract and secure the trailer's support wheel.
  • Close the doors before moving off.
  • Keep pedals, aisles and exits clear.
  • Check belts, seats and luggage restraints.

Exam trap: Wrong: you taste liquid to identify it. Right: find its source without tasting or touching hot parts.

Read the full explanation
  • Start by looking at the ground: a fresh stain can reveal a leak of oil, fuel, coolant or fluid from another circuit. Locate its source without touching hot parts or tasting the fluid; distinguish condensation water from the air conditioning from a mechanical leak.
  • Walk along both sides and around the rear. Look for loose parts, improperly closed doors and damage to the bodywork, mudflaps or guards; check that the trailer’s jockey wheel and moving components are retracted and secured for driving. Also check that the minibus doors close and operate correctly, and do not move off with them open.
  • From the cab, check that you can comfortably reach the controls and see the instruments. Store tools and objects in their designated places to keep the pedal area clear.
  • Check the passenger compartment: seats and seat belts have no visible damage, aisles and exits are clear, and luggage does not obstruct controls or your field of vision. Passenger distribution and the positioning and securing of luggage affect stability; check that they have not shifted and do not obscure lights, signs or number plates. The positioning rules are covered in «Safe loads and luggage», and the visibility and control rules in «Driving techniques for a minibus with a trailer».

3Tyre pressures

A worker uses a pressure gauge to check a tyre on a green minibus with an orange trailer parked on a paved forecourt.
The key idea

Measure your tyre pressures when cold and follow the manufacturer's figures.

Remember

  • Use a pressure gauge: looking or hitting the tyre is not enough.
  • Check the pressure for each axle, wheel arrangement and load.
  • Never deflate a hot tyre to reach its specified cold pressure.
  • Check valves, caps and access to inner wheels.
  • Check your spare wheel if you carry one.
  • Check for damage even with a tyre pressure monitoring system.

Exam trap: Wrong: you deflate hot tyres to their cold pressure. Right: follow the manufacturer's procedure.

Read the full explanation
  • You must check tyre pressures regularly with a suitable pressure gauge; you cannot determine them accurately by looking at the sidewall bulge or striking the tyre. The statutory pressure check is provided for in [RGV, annex VII.6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Measure pressures when the tyres are cold and use the manufacturer’s specified pressure for the load and wheel configuration on each axle. There is no universal pressure suitable for all minibuses, trailers or twin wheels; consult the vehicle and tyre specifications, including after changes in loading conditions.
  • As you drive, the temperature rises and the pressure can increase. Do not deflate a hot tyre to match the specified cold pressure: it can be underinflated when it cools down; if you suspect a problem, carry out the check following the manufacturer’s procedure.
  • Also check valves, valve caps and extensions for the inner wheels, and the spare wheel if you carry one. A tyre pressure monitoring system helps detect pressure losses, but does not replace inspection for cuts and deformation or manual checks when required by the maintenance schedule.

4Incorrect pressures and wear

A mechanic checks the pressure of a tyre with a pressure gauge on a green minibus with an orange trailer parked at a workshop.
The key idea

Keep your tyre pressures correct and find the cause of wear.

Tyre pressurePossible result
Too lowMore heat, fuel use and risk of failure
Too highChanged contact with the road and abnormal wear

Remember

  • Low pressure increases heat and fuel use.
  • Excessive pressure can also cause abnormal wear.
  • Check the whole tread.
  • Do not assume wear has a single cause without checking.
  • If pressure drops again, arrange to have the leak found.

Exam trap: Wrong: you lower pressure to save fuel. Right: use the specified pressure for your load and wheel arrangement.

Read the full explanation
  • If you drive with insufficient pressure, the tyre deforms more, heats up more and is more likely to fail. Rolling resistance and fuel consumption also increase; lowering the pressure is neither a way to save fuel nor protection against a blowout.
  • Excessive pressure does not automatically improve safety either. It can alter the contact patch and promote abnormal wear; you must find the correct pressure for your wheel configuration and load, rather than the highest pressure the inflation equipment allows or the pressure another driver uses in a different vehicle.
  • Observe the wear pattern across the entire tread. Pronounced wear on the shoulders, in the centre or on one side guides your inspection, but does not by itself establish a definite cause: pressure, alignment, suspension or operating conditions can all play a part.
  • Do not wait for a long journey to correct an incorrect pressure. If the pressure drops again after inflation, arrange to have the leak located; repeatedly adding air without checking the valve, rim and tyre leaves the problem unresolved and can conceal internal damage.

5Minimum tread depth by category

A mechanic measures the tyre tread of a trailer attached to a minibus parked beside the right-hand kerb.
The key idea

Check the minimum tread depth for each vehicle category in your combination.

1.0 mmM2/M3 minibus; O3/O4 trailer
1.6 mmO2 trailer
Vehicle and categoryMinimum depth in main grooves
M2 or M3 minibus1.0 mm
O3 or O4 trailer1.0 mm
O2 trailer1.6 mm

Remember

  • Check each vehicle's technical category.
  • Measure the main grooves at different places around each tyre.
  • Deeper tread elsewhere cannot make up for a worn area.
  • Do not assume legal tread depth guarantees enough grip in all rain.

Exam trap: Wrong: you apply the same minimum to every wheel. Right: check the minibus and trailer categories separately.

Read the full explanation
  • On a category M2 or M3 minibus, you must maintain at least 1.0 mm in the main tyre grooves while using public roads. The same minimum applies to O3 and O4 trailers. Identify the technical categories in each vehicle’s documentation. [RGV, annex VII.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • If you tow an O2 trailer, its tyres must retain at least 1.6 mm in the main grooves. A single D1+E combination can therefore have a minimum of 1.0 mm for the minibus and 1.6 mm for the trailer; your driving licence does not make their technical categories the same. [RGV, annex VII.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Measure tread depth in the main grooves and examine different areas around the circumference. The most worn area is not compensated for by deep tread elsewhere; a quick look at the outer face can miss wear on the inner shoulder or localised damage.
  • Do not interpret the legal minimum as a guarantee of sufficient grip in all rain conditions. You must assess the water, tyre condition and the combination’s behaviour; a deteriorated tyre impairs steering and braking, and its properties do not improve because it is fitted to a heavy vehicle.

6Tyres, rims and wheel fastenings

A mechanic inspects a bulge and a split in the sidewall of the rear tyre of a minibus with a trailer parked beside the right-hand kerb.
The key idea

Check your wheels for damage, secure fastenings and approved specifications.

3.5 tRegrooving: MMA must exceed
Tyre workWhat changes
RetreadingRenews the tread
RegroovingDeepens tread designed for this

Remember

  • Look for bulges, cuts, deep cracks and exposed tyre layers.
  • Do not drive with structural damage, even with enough tread.
  • Check rims, nuts and signs of movement.
  • Fit only sizes and specifications permitted for your vehicle.
  • Follow the manufacturer's tightening instructions and later checks.
  • Leave regrooving to specialists and check it is permitted.

Exam trap: Wrong: you regroove any tyre. Right: regrooving requires vehicle MMA above 3.5 t and tyres marked Regroovable or with the regulatory symbol.

Read the full explanation
  • Examine the tread and sidewalls for bulges, cuts, deep cracks, separation or exposed cords. You must not drive with abnormal deformation or structural damage of the types covered by [RGV, annex VII.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii); retaining tread depth does not compensate for a damaged carcass.
  • Visually check rims and fastenings: a missing nut, a crack or signs of movement require inspection. After removing a wheel, follow the manufacturer’s specified tightening torque, sequence and subsequent check.
  • You must fit sizes and specifications approved for the vehicle or permitted equivalents. Check the load index, suitability for single or twin fitment and speed rating; the fact that a tyre physically fits the rim does not prove it is suitable. [RGV, annex VII.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Distinguish retreading from regrooving: the former renews the tread, while the latter deepens a tread designed for this purpose. Regrooving is only permitted on vehicles with an MMA (maximum authorised mass) of more than 3.5 t and tyres marked Regroovable or bearing the regulatory symbol; have specialists carry out the operation. [RGV, annex VII.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • The rim supports the tyre; within the tyre, the carcass provides strength, the tread contacts the ground and the sidewalls allow lateral flexing. In radial construction, the carcass plies run radially and belts reinforce the tread. A tubeless tyre requires an airtight seal with a compatible rim and valve; you cannot repair a leak without identifying where it occurs.

7Check twin wheels

A maintenance worker uses a pressure gauge to check the inner twin tyre of a minibus with a trailer parked beside the right-hand kerb.
The key idea

Check the inner tyre of each pair of twin wheels too.

Remember

  • Check both tyre pressures with suitable equipment.
  • Use compatible tyres and the same specified pressure for that arrangement.
  • Avoid large differences in wear or diameter.
  • Look for trapped stones and rubbing between tyres.
  • Arrange safe assistance for damage or a trapped stone.

Exam trap: Wrong: you continue because the outer twin tyre holds air. Right: a deflated twin can overload the other tyre.

Read the full explanation
  • With twin wheels, you must inspect both tyres, including the inner one. The outer tyre may still look normal while the other loses air; the sound tyre then bears additional strain, and this does not allow you to continue indefinitely with the other tyre deflated.
  • Check that the paired tyres have compatible dimensions and maintain the same pressure specified for that arrangement. Avoid significant differences in wear or effective diameter: if they do not work in a similar way, the load is shared unevenly between them and they deteriorate faster.
  • Look at the gap between the wheels and check for trapped stones or other objects. The specified gap must be maintained without the sidewalls rubbing; low pressure or overloading can encourage this contact and hinder heat dissipation, even though you can only see one tyre from outside.
  • Use suitable access equipment to measure the inner tyre's pressure and check its valve. If you find a trapped stone, a deformation or a tyre that has been driven on while deflated, arrange for the work to be carried out safely: do not strike or dismantle the assembly while it is under load as part of a routine inspection.

8Chains and winter equipment

A green minibus with an orange trailer is parked beside a snowy road, with snow chains on the minibus's driven rear wheels and no chains on the trailer's wheels.
The key idea

Prepare winter equipment for the driving wheels and mass of each vehicle.

3,500 kgWinter equipment MMA threshold
Vehicle MMA during winter restrictionsRequired special tyresAxles you must equip
Above 3,500 kg3PMSF or PORAt least steering and driving axles
3,500 kg or less3PMSFAll axles

Remember

  • When chains are required, fit them to a driving wheel on each side.
  • You may use special tyres that meet the regulations.
  • Do not mistake trailer wheels for driving wheels.
  • Check chain size, condition and instructions.
  • Do not treat M+S alone as sufficient certification.
  • Carrying chains does not let you pass a road closure.

Exam trap: Wrong: you fit chains only to the trailer. Right: identify the driving wheels and equip the combination according to the regulations.

Read the full explanation
  • When using chains or other authorised anti-slip devices is compulsory or recommended, you must fit them to at least one driven wheel on each side, or use special tyres in accordance with the regulations. Identify the axles that transmit driving force: the trailer's wheels are not driven merely because they carry a load. [RGV, art. 12.5.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • To comply with winter travel restrictions by using special tyres, if the vehicle has an MMA (maximum authorised mass) above 3,500 kg, it must have 3PMSF- or POR-certified tyres on at least the steering axle and the driven axles. If its MMA is 3,500 kg or less, it must have 3PMSF tyres on all its axles; apply the criterion to each vehicle concerned. [RGV, Annex VII.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Special snow tyres bear the marking M+S, M&S or M.S together with 3PMSF; tyres for professional off-road use bear that marking together with POR. Check both markings on the sidewall when preparing the vehicle for a winter restriction. [RGV, Annex VII.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Before the journey, check that the devices match the wheel size, are not broken and that you can fit them by following their instructions. Practise in a safe place, check their tension when the manufacturer instructs you to and observe their conditions of use; having chains does not authorise you to pass a road closure.

9Removing and fitting a wheel safely

A mechanic works on a grounded wheel of a minibus towing a trailer, both secured with wheel chocks on a firm, level surface, with a jack ready and two passengers seated away on a bench.
The key idea

Change a wheel only with training, suitable equipment and a safe place.

Remember

  • Keep passengers safe and avoid working beside traffic.
  • Secure both vehicles with brakes and chocks as the procedure requires.
  • Use a suitable jack at the designated lifting points.
  • Initially loosen fastenings with the wheel on the ground.
  • Never go under a vehicle supported only by a jack.
  • Follow tightening instructions and make the later check when required.

Exam trap: Wrong: you tighten as hard as possible. Right: follow the specified sequence and torque; overtightening also causes damage.

Read the full explanation
  • You must only consider changing a wheel if you have the training, suitable equipment and a protected location with firm, level ground. On a minibus, the wheel's weight and the load supported by the jack may require professional assistance; keep passengers in a safe area. Do not carry out the operation beside traffic or on a surface that could give way.
  • Secure both vehicles against movement before lifting: apply the brakes and suitable wheel chocks where the procedure specifies. Prepare a jack with sufficient capacity, the correct wheel wrench and equipment to handle the wheel without trapping yourself. Use only the designated lifting points; the floor pan or an arbitrary suspension component must not serve as an improvised support.
  • Initially loosen the fastenings with the wheel on the ground, without removing them yet; then lift only as far as necessary and complete removal following the manual. Keep your hands and feet away from crushing hazards and do not go underneath a vehicle supported only by a jack. If the support becomes unstable, stop the operation.
  • Before fitting, clean the mating surfaces of the rim and hub and inspect the studs, threads and seats. Fit a compatible wheel in the correct direction and mounting position, leaving the valve accessible. Do not lubricate threads or seats on your own initiative: their lubrication condition must match the procedure and torque specified by the manufacturer.
  • Start the fastenings by hand and tighten progressively in the prescribed sequence, normally alternating between opposite positions, without forcing cross-threaded fastenings. Complete tightening under the conditions specified by the manufacturer, using a torque wrench where required and the torque specified for that rim and fastening. Overtightening can also damage the fastening components.
  • Check the pressure, seating and fastening when you finish; collect your tools and stow the removed wheel securely. Carry out the subsequent tightness check at the time specified by the manufacturer. Removing a tyre from a rim, especially one with detachable components or used in a heavy-duty assembly, requires specific tools and training.

10Engine, fuel supply, starting and transmission

A mechanic looks at the engine under the open bonnet of a green minibus with a trailer, parked beside the right-hand kerb in an area off the carriageway.
The key idea

Recognise your engine systems and leave dangerous work to trained people.

Part in a combustion-engine minibusFunction
BatterySupplies energy for starting and electrical equipment
Starter motorTurns the combustion engine
AlternatorGenerates electricity while the engine runs
ClutchConnects or disconnects engine and transmission
GearboxAdapts the ratio between engine and wheel speeds
DifferentialAllows driving wheels different speeds on bends

Remember

  • Do not loosen injection pipes: dangerous pressure may remain.
  • Arrange checks for jerking, slipping or difficulty changing gear.
  • If you suspect exhaust fumes entering, protect passengers and arrange inspection.
  • Do not touch hot exhaust parts or disable emissions treatment.
  • Leave high-voltage work to qualified people.

Exam trap: Wrong: you open a window to fix an exhaust leak. Right: protect passengers and arrange inspection.

Read the full explanation
  • In a minibus with an internal combustion engine, the pistons transmit motion to the connecting rods and crankshaft. The four-stroke cycle comprises intake, compression, power and exhaust; in a diesel engine, air is compressed and fuel is then injected, igniting on contact with that hot air. Knowing what each system does helps you interpret difficult starting or a loss of power without dismantling the engine.
  • The fuel supply system carries fuel from the tank, through filters and pipes, to the injection system; air enters through its own intake system. A blocked filter, air entering the fuel system or a leak can cause rough running. Inspect accessible parts and report the symptom, without loosening injection pipes, which may retain dangerous pressure.
  • The battery supplies energy for starting and for electrical equipment; the starter motor turns the combustion engine and the alternator generates electricity while the engine runs. If the starter turns slowly, have a competent person check the battery, connections and starter itself; if it turns normally but the engine does not start, the cause may lie in another system.
  • The clutch connects the engine to, or disconnects it from, the rest of the transmission, and the gearbox adjusts the ratio between engine speed and wheel speed. The differential allows the driven wheels to turn at different speeds on bends. Juddering, slipping, difficulty changing gear or lubricant leaks call for these components to be checked; follow the maintenance requirements for the gearbox and final drive fitted to your minibus.
  • Inspect accessible exhaust mountings and check for damage, and pay attention to abnormal smoke, new noises or the smell of exhaust gases inside the passenger compartment. Protect passengers and arrange an inspection if you suspect gases are entering; opening a window does not resolve a leak. Do not handle a hot exhaust or disable emissions treatment systems.
  • These checks depend on the powertrain fitted: an electric minibus does not have the fuel or oil systems of a combustion engine. Observe high-voltage warnings and leave this work to qualified personnel; checks on wheels, brakes, lights and the coupling remain necessary.

11Engine oil and lubrication

A mechanic examines the oil dipstick beside the open bonnet of a minibus with a trailer parked on level ground beside the right-hand kerb.
The key idea

Check your oil level and act if lubrication pressure is low.

Oil checkWhat it tells you
LevelQuantity available
PressureOil circulation

Remember

  • Measure with the combination level and engine stopped.
  • Follow the manufacturer's temperature and waiting instructions.
  • Do not exceed the maximum mark.
  • Use oil meeting the required specifications.
  • If the pressure warning appears while running, stop safely and switch off.
  • Change oil and filters as scheduled: topping up cannot replace this.

Exam trap: Wrong: you dismiss low pressure because oil is present. Right: sufficient oil level does not guarantee sufficient pressure.

Read the full explanation
  • Check the oil level with the combination on level ground and the engine switched off, observing the temperature and waiting time specified by the manufacturer. Use the dipstick or designated electronic check and verify that the reading is within the level marks, without exceeding the maximum.
  • The level tells you how much oil is available; the pressure warning concerns the circulation of the lubricant. You can have oil in the sump and still suffer a loss of pressure: if this warning appears while the engine is running, you must stop safely and switch off the engine to prevent damage.
  • When topping up, use oil that meets the required specifications and add controlled amounts. Do not mix products merely because they share a colour or trade name; if you have to top up frequently or notice stains, abnormal oil consumption or oil contamination, arrange for the cause to be diagnosed.
  • Follow the manufacturer's oil and filter change schedule, adapted to the work the minibus performs. Topping up does not replace changing degraded lubricant or a clogged filter; record the work so that you do not confuse a top-up with a full service.

12Cooling and temperature

A driver wearing a reflective vest waits on the pavement beside a stopped minibus towing a trailer, with the bonnet raised and the coolant cap closed while heat waves rise from the engine.
The key idea

Check your coolant when cold and act on temperature alarms.

Remember

  • Check the level in the expansion tank.
  • Look for leaks in hoses, connections and the radiator.
  • Do not open the cap while the cooling system is hot.
  • Keep hands away from fans that may start automatically.
  • Use the specified coolant and concentration.
  • For a serious alarm, stop safely and follow the procedure.

Exam trap: Wrong: you open the hot cap to check the level. Right: wait for cooling and follow the instructions.

Read the full explanation
  • Check the coolant with the engine cold and check the level in the expansion tank. Look at hoses, connections and the radiator for leaks or deterioration; repeated drops in level require you to investigate the cause, even if you can temporarily restore the level by adding the correct product.
  • Do not open the cap when the cooling system is hot: pressurised liquid can spray out suddenly and burn you. Wait for it to cool and follow the safety instructions; also keep your hands away from a fan that may start automatically, even when the vehicle is stationary.
  • Use the specified coolant and observe its concentration and replacement requirements. Its functions include controlling temperature and protecting the system; do not treat it as a tank into which you can add any water or product without checking compatibility, especially when preparing the minibus for severe cold.
  • If the temperature rises outside its normal range or a serious warning appears, find a safe place to stop and follow the manufacturer's procedure. Continuing to demand power can make the damage worse; the warning light alone does not tell you whether the fault concerns the level, airflow, pump or another component.

13Other levels, tanks and filters

A person replenishes AdBlue through the blue filler opening of a minibus with a trailer parked beside the kerb, while the diesel cap remains closed.
The key idea

Identify each tank and follow your maintenance instructions for levels and filters.

Remember

  • Check you have enough fuel and the caps are closed.
  • If you use AdBlue, top up only through its correct filler.
  • Never put AdBlue in diesel or replace it with water.
  • If hydraulic brake fluid drops, arrange investigation.
  • Check levels in the systems fitted to your vehicle.
  • Do not disable filters or bypass fuses.

Exam trap: Wrong: you remove a filter to clear a warning. Right: arrange the specified action and keep its protection.

Read the full explanation
  • Check that you have enough fuel and that the fuel tanks are securely closed. If your minibus uses AdBlue, check its level and top it up only through the correct filler opening: it is an exhaust gas treatment product, and you must not put it in the diesel tank or replace it with water.
  • Identify your minibus's braking system: depending on the model, it may be hydraulically operated, air-operated or a combination of both. With a hydraulic system, check the level of the specified fluid and look for leaks; a drop in level may be linked to wear or a leak, and you must find the cause. Also check the fluid levels in the power steering and any other circuits actually fitted to your vehicle.
  • Check air filters, fuel filters and other components according to the maintenance schedule and your vehicle's indicators. If you receive a restriction or contamination warning, arrange the specified action; do not remove or bypass a filter to make the symptom disappear so that you can finish your journey.
  • Check that tanks, batteries and covers are securely fastened and have no leaks or visible damage. Follow the manufacturer's electrical procedures and do not bridge fuses or handle terminals without the necessary training; an improvised repair can cut power to the lights, braking units or other essential systems.

14Lights on the towing and towed vehicles

A person checks the illuminated rear lights of a trailer coupled to a minibus stopped in a paved yard from outside the vehicles.
The key idea

Check from outside that the lights on both your vehicles work.

Remember

  • Test the lights on your minibus and trailer.
  • Include end-outline and side marker lights where applicable.
  • Check interior lighting if your minibus provides public passenger transport.
  • Clean lights, reflectors and reflective surfaces.
  • If several trailer lights fail, inspect the connector safely.

Exam trap: Wrong: you trust only the minibus warning lamp. Right: check that the trailer lights actually work.

Read the full explanation
  • You must check from outside that the lights actually work, with assistance or using the checking system fitted to your minibus. An indicator lighting up on the towing vehicle's dashboard does not by itself prove that the lights on the last vehicle in the combination work.
  • Include your minibus's dipped beam and main beam in the check, along with the position lights, brake lights, indicators, hazard warning lights, rear fog lights and number plate lighting on both vehicles; add end-outline marker lamps and side marker lamps where applicable. The interior lighting in your minibus used for public passenger services must also work. [RGV, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • Also check light lenses, reflectors and reflective surfaces: they must be clean, securely fastened and free of damage that reduces their effectiveness. When checking a long vehicle, walk along both sides; a light that is dirty or obscured by an accessory may fail to fulfil its function even though its bulb remains lit.
  • If several lights on your towed vehicle fail at the same time, check the connector safely and report the defect. Do not use switching on the interior light as a substitute for the check or disconnect warnings to hide the defect; the compulsory equipment is covered in detail in «Safety devices on the combination».

15Mirrors, glazing and windscreen wipers

A driver checks the windscreen washer of a green minibus with an orange trailer, parked beside a kerb.
The key idea

Keep a clear view through your mirrors, windows and windscreen.

Remember

  • Adjust your seat, then mirrors, while stationary.
  • Check cleanliness, mountings and field of view.
  • Check cameras and screens if fitted.
  • Test washer jets and check wiper blades.
  • Do not operate blades frozen to the glass.
  • If you lose visibility, stop safely to restore it.

Exam trap: Wrong: you assume washer fluid guarantees visibility. Right: check jets and blades too.

Read the full explanation
  • Adjust your seat and then your mirrors while your vehicle is stationary. Check that they are securely mounted and clean and check their field of view, including the devices that let you monitor areas near the cab and along the sides; a poorly adjusted mirror does not improve your control of the trailer on bends.
  • You must maintain an adequate view through the windows and using the devices for indirect vision. The technical requirements for glazing, mirrors, windscreen wipers and washers are set out in [RGV, art. 11](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11); also check cameras and screens where fitted.
  • Operate the windscreen washer and check that the jets reach the area swept by the wipers. Check the fluid level, pipes and wiper blades: if the blades leave streaks, judder or spread dirt, they need cleaning or replacement; having washer fluid does not guarantee visibility if the rubber blades are worn.
  • Check the demisting system and remove ice or dirt without damaging the glass or rubber seals. Use fluid suitable for the ambient temperature and avoid operating wiper blades frozen to the glass; if you lose visibility while driving, you must find a safe place to stop and restore it before continuing.

16Steering, suspension and chassis

A technician uses a flashlight to inspect a crack in the coupling support of a minibus with a trailer stopped beside the right-hand kerb.
The key idea

Deal with steering, suspension and structural defects before you drive.

Remember

  • Arrange checks for steering looseness, pulling or unusual resistance.
  • Look for leaning, broken parts and suspension leaks.
  • Check air suspension reaches its specified driving height.
  • Do not assume sound tyres compensate for damaged suspension.
  • Stop using the vehicle if a crack may affect its strength.

Exam trap: Wrong: you drive at the height used for coupling. Right: check the specified driving height.

Read the full explanation
  • Check for play, abnormal resistance, pulling or vibration in the steering. You must not treat these as mere discomfort: the steering keeps you on course, and its failure can compromise your control even when you drive slowly or on a road you know well.
  • Look for leaning in the combination, broken suspension components or an air spring leaking air. Before setting off, check that the air suspension reaches the specified driving height; the setting used for loading or coupling may not be suitable for driving.
  • The suspension and shock absorbers help keep the wheels in contact with the road. Their deterioration can impair stability and braking; a correctly inflated tyre does not compensate for damaged suspension, just as a sound towing vehicle does not correct defects in the trailer.
  • Look for visible damage to the chassis, cross-members and coupling mountings, especially after an impact or contact during a manoeuvre. Do not try to assess a structural crack by its apparent size; stop using the vehicle and seek a technical assessment if the crack could affect structural strength or the coupling.

17Coupling and supports: mechanical inspection

A person checks the coupling latch and safety retainer between a minibus and a trailer with chocked wheels on a paved area.
The key idea

Check your coupling closure and safety lock using its model's instructions.

Coupling partCare
Points requiring lubricationLubricate as the manufacturer specifies
Friction surfaces requiring grease-free operationDo not grease

Remember

  • Check that the connections are compatible.
  • Check coupling wear, mounting, indicator and closure.
  • Clean and lubricate only where the manufacturer specifies.
  • Keep friction surfaces grease-free where required.
  • Check the support wheel, crank and locks.
  • Before uncoupling, secure the trailer and support it on firm ground.

Exam trap: Wrong: you assume a click means the coupling is closed. Right: verify actual closure and its safety lock.

Read the full explanation
  • Your coupling must be compatible with the vehicles and have a device that prevents it from opening unintentionally. Inspect its mountings, fastenings and locking mechanism for damage or wear; you must follow the manufacturer's instructions for the mechanical check. [RGV, art. 13.1 and 13.3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • On a ball coupling head or pin coupling, depending on the approved model, examine the contact surfaces and wear indicators. Increasing play, deformation or difficulty operating the mechanism requires inspection before service; apply the manufacturer's wear limits and have competent personnel replace the affected parts.
  • Clean and lubricate only the points specified for your model. There is no universal greasing interval for all coupling heads: some friction stabiliser surfaces must remain free of grease, while other couplings need lubrication; always follow the instructions for the mechanism actually fitted.
  • Check your trailer's support wheel, crank handle, clamp and locking devices. Before uncoupling, secure the trailer against movement and support it on firm ground using the specified equipment; the weight on the drawbar can cause it to drop when you release the coupling head. The full sequence is covered in «Coupling and uncoupling the trailer».

18Connections and breakaway devices

A mechanic checks the electrical connection beside the overrun brake coupling and breakaway cable of a trailer attached to a parked minibus.
The key idea

Check your connections and distinguish devices that act when the trailer separates.

1,500 kgSecondary coupling: maximum MMA
Connection on a trailer with two-line air brakesFunction
RedAir supply
YellowBrake control

Remember

  • Look for damaged, loose or badly connected cables and hoses.
  • Allow turning without stretching or dragging connections.
  • Check with an empty trailer and in dry weather too.
  • If you have overrun brakes, check their parts using the manual.
  • Do not swap different devices because they resemble cables or chains.

Exam trap: Wrong: you confuse a secondary coupling with separation braking. Right: a secondary coupling is required for trailers up to 1,500 kg MMA when braking is not activated by coupling breakage.

Read the full explanation
  • Inspect electrical cables and, where fitted, air hoses throughout the accessible area. Look for chafing, cracks, unsafe joints and poorly secured connectors; they must allow articulation without becoming taut, dragging or snagging. Check the connections when your trailer is empty and in dry weather, just as you do for any other service.
  • If your trailer has two-line air brakes, the red line is the supply line and the yellow line is the brake control line; check the markings, secure attachment and absence of leaks. On a trailer with overrun brakes, check the sliding coupling head, bellows, linkage and breakaway cable according to its manual; do not look for air connections that this system does not have.
  • Distinguish between a device that applies the brakes on separation and a secondary safety coupling that retains some residual guidance and prevents the drawbar from touching the ground. The latter is required on trailers with an MMA (maximum authorised mass) of up to 1,500 kg without a system that applies the brakes if the coupling breaks. [RGV, art. 13.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Check the devices appropriate to your particular towed vehicle and do not substitute one for another because they look like a cable or chain. You study the full connection and disconnection sequence in «Coupling and uncoupling the trailer»; during maintenance, you must identify damage, incompatibility and insecure locking.

19What you must check in the brakes

A green minibus towing an orange trailer travels straight along a flat, clear road with the brake lights of both vehicles illuminated.
The key idea

Test your combination's brakes and check that the accelerator returns to rest.

BrakeFunction
ServiceBrakes while you drive
ParkingKeeps the vehicle stationary
SecondaryStops the vehicle if the service brake fails

Remember

  • Check the trailer brakes too.
  • Test at very low speed in a safe, clear area.
  • Arrange checks for delays, noises, pulling or wheels staying braked.
  • Check brakes on level, dry ground too.
  • Keep objects and mats away from the accelerator.
  • Do not set off if the accelerator sticks.

Exam trap: Wrong: you confuse the retarder with the secondary brake. Right: distinguish each system's function.

Read the full explanation
  • You must check the response of the service brake and that the parking brake holds the vehicle stationary, including the towed vehicle. The secondary brake allows you to stop the vehicle if the service brake fails; do not confuse these functions with the retarder. [RGV, Annex VIII.1.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anviii).
  • Check accessible parts for wear, inspect pipes and hoses, and look for possible contamination of friction components. Adjustments and repairs to discs, drums, pads, shoes or brake chambers require the appropriate technical procedure; you must not compensate for a fault by increasing tyre pressures or tightening parts by guesswork.
  • In a safe area with clear space, check at very low speed that the combination brakes progressively without pulling abnormally to either side. A delayed response, a wheel that remains braked, a new noise or an imbalance requires inspection before you join traffic.
  • The brakes must also work on level ground and dry surfaces. Do not leave checking them until a descent: with a high mass, even a partial failure can affect stability and increase the distance you need to stop, even if the towing vehicle still gives you a sense of braking.
  • Check that the accelerator moves freely and returns to its resting position, without floor mats or objects holding it down. An abnormal response, a sticking pedal or engine speed that does not match your input requires inspection; do not set off relying on the brake to compensate. With an electronic system, you must also heed warnings and the operating mode specified by the manufacturer.

20Building up and monitoring compressed air

A driver checks the two pressure gauges and illuminated air-brake warning in a minibus with a trailer stopped beside the right-hand kerb.
The key idea

If you have air brakes, wait for the correct pressure before setting off.

Remember

  • Watch each circuit's pressure gauge.
  • Wait for your system's specified operating range.
  • Check that low-pressure warnings clear.
  • Look for air leaks with the combination secured.
  • If pressure drops and a warning appears, find a safe stopping place.
  • Do not silence the warning to continue.

Exam trap: Wrong: you pump the pedal to restore air pressure. Right: this uses air and does not repair the leak.

Read the full explanation
  • If your minibus or its trailer uses air brakes, the compressor supplies air and the reservoirs store the energy needed to operate the brakes. Monitor the circuit gauges and wait until pressure reaches the specified operating range before releasing the brakes holding the combination stationary and moving off; the air-system checks in this section apply to the equipment fitted to your combination.
  • Check that low-pressure warnings clear as intended by the manufacturer. There is no single pressure for moving off that applies to every minibus: use the reference values for the installed system and do not assume another vehicle's reading is normal for yours.
  • With the combination secured against movement, listen for leaks and watch for an abnormal pressure drop. Insufficient pressure, audible leaks and poor pressure recovery are items checked during commercial vehicle inspections; silencing the warning device does not fix them. [RD 563/2017, Annex II, section 1.1.3](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-2).
  • If pressure drops during your journey and the warning activates, find a safe place to stop before you lose braking ability. Pumping the pedal consumes air and does not repair a leak; you must not rely on revving the engine to make it acceptable to continue with a faulty circuit either.

21Reservoirs, air dryer and spring brakes

A driver wearing a reflective vest makes a phone call from the pavement beside a minibus and trailer, both parked and secured with wheel chocks.
The key idea

Maintain your air dryer and drains, and leave spring brakes to specialists.

Remember

  • Follow the maintenance plan for your equipment.
  • Check automatic drainage works if fitted.
  • For manual draining, secure the combination and follow its instructions.
  • Arrange investigation of abnormal water or oil.
  • Do not drag a vehicle held by brakes because air pressure is missing.
  • Never dismantle spring brake chambers: dangerous energy can remain without air pressure.

Exam trap: Wrong: you assume a spring chamber is safe without air. Right: leave work on it to competent people.

Read the full explanation
  • Moisture in the air can condense in the reservoirs and impair the system. Check the maintenance of the air dryer and drains according to the equipment fitted; if draining is automatic, check that it works rather than assuming it removes any need for inspection.
  • If the system requires manual draining, carry it out with the combination secured against movement and in accordance with its instructions. Do not adopt a universal interval regardless of the climate, air dryer or manufacturer; an abnormal amount of water or oil in the drained discharge requires investigation of the cause.
  • With spring brake actuators, if fitted to your vehicle, mechanical energy applies or holds the brake and air pressure allows it to release according to the design. If air is lacking, you may find the vehicle held by its brakes; you must not drag it or disable its mechanisms to finish the service, but request assistance equipped to deal with that system.
  • Do not dismantle spring brake chambers or tamper with their release components as part of a daily inspection. They can retain dangerous energy even without air pressure; recovery work requires competent personnel and measures to ensure that the towing and towed vehicles cannot move.

22ABS, EBS and electronic control

A mechanic uses a torch to inspect the electrical connection between a minibus and its trailer, parked beside the kerb, with the cable plugged in.
The key idea

Interpret your electronic warnings using the manual and symptoms.

Remember

  • Check warning-light test sequences on your minibus and trailer.
  • Remember that ABS cannot create grip.
  • Maintain tyres, sensors, cables and connections.
  • Do not disconnect the trailer system to clear a warning.
  • Record the message and report which vehicle is affected.

Exam trap: Wrong: an ABS warning always lets you continue. Right: check the fault; with a stop instruction, insufficient pressure or loss of response, secure the combination safely and request assistance.

Read the full explanation
  • Check the self-diagnostic cycle of the ABS warning lights and the combination's electronic systems. Their behaviour depends on the model and may include checks as you start moving; consult the manual before treating an intended sequence as a fault or assuming a persistent warning is normal.
  • ABS helps prevent wheel lock during braking; electronic control does not create grip or correct a damaged tyre. You must keep tyres, sensors, wiring and connections in good condition and maintain a safety margin even if the minibus has advanced braking and stability aids.
  • An ABS warning does not necessarily mean that all service braking is lost, but it indicates that you must check the fault. If it is accompanied by an instruction to stop, insufficient pressure or a loss of response, you must secure the combination safely against movement and request assistance before continuing.
  • Do not disconnect the towed vehicle's electronic system plug to extinguish a warning. You must record the message, identify whether it relates to the towing vehicle or trailer and report it to the workshop; diagnosis must check the affected combination, rather than merely clear the fault code.

23Interpreting dashboard warnings

A green minibus with a trailer is stopped beside the right-hand kerb, with the driver seated and an illuminated oil warning light on the dashboard visible through a cutaway of the cab.
The key idea

Read each dashboard warning and follow its instructions.

Remember

  • Check warning lights when you switch on the ignition.
  • Read messages: colour alone does not decide your action.
  • For a serious alarm, stop safely.
  • With low oil pressure, stop and switch off the engine.
  • For a brake air-pressure warning, also secure the combination against movement.
  • Record symptoms without distracting yourself while driving.

Exam trap: Wrong: you treat every amber warning as permission to finish. Right: check its meaning, symptoms and instructions.

Read the full explanation
  • When you switch on the ignition, check that the warning lights perform the intended check and that the relevant warnings go out when the system is ready. Read the display messages too: colour gives an indication of urgency, but the specific warning determines its meaning and the action required.
  • A serious oil, temperature or brake alarm requires you to stop safely and follow the corresponding instruction. If the warning indicates insufficient lubricating oil pressure, you must switch off the engine after stopping the vehicle; if it concerns braking air pressure, you must also secure the combination against movement.
  • If the electrical charging warning light stays on with the engine running, it may indicate a generation or power supply problem. You must heed it and request inspection: the fact that the engine keeps running does not guarantee that you can maintain lights, control units and the combination's other electrical systems indefinitely.
  • Do not assume that every yellow warning allows you to finish the route. Check its meaning, the symptoms and the manufacturer's instructions; note when it appears, whether it changes as you drive and which other warnings accompany it, without operating screens or carrying out distracting tests while driving.

24Noises, overheating and blowouts

A minibus towing a trailer is stopped beside the right-hand kerb with smoke rising from a rear wheel, while a man in a reflective vest makes a phone call from the pavement, away from the wheel.
The key idea

Keep control and stop safely if you face vibrations, abnormal heat or a blowout.

Remember

  • Find the cause of unusual noises and vibrations.
  • Do not touch a hot wheel or keep driving to cool it.
  • Keep people away if fire or tyre failure is possible.
  • In a blowout, hold the steering firmly and slow down in control.
  • Avoid harsh braking and sudden turns.
  • If heat reduces braking effectiveness, find a safe stopping place.

Exam trap: Wrong: you assume cooling fixes overheating. Right: arrange investigation of its cause.

Read the full explanation
  • If abnormal noises or vibrations occur, you must investigate their cause as soon as possible. Reduce the demands on the vehicle and find a safe place to stop if they may affect control; accelerating through the vibration range or waiting for it to disappear by itself leaves the fault unresolved.
  • A strong brake smell, smoke or abnormal heating of a wheel may indicate a binding brake, a bearing problem or another fault. Do not touch hot parts or keep driving to cool them; request inspection and keep people away if there is a risk of fire or tyre failure.
  • If you have a blowout, hold the steering wheel firmly, avoid abrupt corrections and reduce speed in a controlled way until you stop somewhere safe. Harsh braking or a sudden turn can destabilise the combination; also check for possible damage to twin tyres, pipes and hoses, bodywork and fastenings.
  • If the brakes lose effectiveness through heat, you must treat this as a safety problem and stop where you can do so without creating a greater risk. The use of gears and retardation on descents is covered in «Driving techniques for a minibus with a trailer»; cooling the system does not replace finding out why it has overheated.

25Roadside breakdown: warn others and protect yourself

A minibus towing a trailer is stopped beside the right edge of the road with a V-16 beacon and hazard lights illuminated, while a person wearing a reflective vest stands on the grass.
The key idea

Carry your required equipment and warn others if your combination breaks down.

Remember

  • Check your connected, certified V-16 has valid power and connectivity.
  • Carry a reflective vest and an approved, suitable, serviceable fire extinguisher.
  • For a hazardous roadside breakdown, stop safely and use your connected V-16.
  • Switch on hazard warning lights.
  • Add position lights and end-outline marker lamps where appropriate.
  • Check your spare wheel if carried; it is not required equipment.

Exam trap: Wrong: you replace the connected V-16 with triangles. Right: use the regulatory device and request assistance.

Read the full explanation
  • Before setting off, check that you carry a certified connected V-16 with a working power supply and a valid connectivity service, a high-visibility reflective vest and approved, suitable and serviceable fire-extinguishing equipment; check the extinguisher's condition and maintenance. The equipment required for the minibus and the D1+E combination does not include a spare wheel, although you must check it if you carry one; equipment is covered in detail in «Safety devices on the combination». [RGV, Annex XII.1.a), 1.b) and 2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii). The beacon's specifications are regulated in [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • If you break down, you must stop the combination safely and warn others using the connected V-16, the hazard warning lights and, where appropriate, the position lights and end-outline marker lamps. For passengers leaving safely, use of the vest and requesting assistance, consult «Responding to accidents and breakdowns»; the equipment and its use are covered in «Safety devices on the combination». [RGC, art. 130.2-4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130) and [art. 118.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a118).

26When you can resume driving

A technician inspects the hitch of a minibus and trailer immobilized beside the right-hand kerb, with a trailer wheel chocked and the driver waiting nearby.
The key idea

Continue only when you have restored safe conditions.

Remember

  • Check the cause is resolved and no related damage remains.
  • Recheck parts affected by the repair.
  • A warning clearing after restarting does not prove a repair.
  • Keep the combination stationary with major brake, steering, tyre or coupling defects.
  • Request suitable assistance and record what happened.
  • Do not improvise recovery with chains or cables.

Exam trap: Wrong: you keep your speed after lighting fails beyond roadside repair. Right: if forced to use lower-intensity lighting, slow down to stop within the lit area, always maintaining safe conditions.

Read the full explanation
  • Before continuing, you must check that the cause has been resolved and that no associated damage remains. Check the wheels, locking mechanism, connections, supports and warnings again if the work has affected them; a warning lamp going out after switching the ignition back on does not by itself prove that a repair has been successful.
  • If a fault that cannot be repaired en route forces you to use less intense lighting, you must reduce your speed so that you can stop within the illuminated area. This rule does not authorise you to drive without visibility or in unsafe conditions. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107).
  • With major defects in the brakes, steering, tyres or mechanical coupling, you must keep the combination immobilised and seek suitable assistance. A towed vehicle without effective brakes does not become safe simply because the towing vehicle can pull it; you must not improvise recovery using makeshift chains or cables either.
  • Report and record what happened so that follow-up action can be taken. A temporary repair may require a later inspection, replacement parts or a technical check before another service; keep the workshop's information and distinguish between resolving the symptom and restoring the combination's safe condition.

27Find the cause and limit the repair

A person inspects the electrical connector of a trailer attached to a minibus parked beside the kerb with a flashlight, with an open manual on a toolbox.
The key idea

Describe your fault and limit repairs to work intended for users.

Remember

  • Record what happens and when, with the combination stationary.
  • Consult the manual and start with accessible parts.
  • Do not test in traffic or erase warnings without recording them.
  • Do simple work only with the correct procedure, knowledge and equipment.
  • Check operation after your work.
  • If you cannot verify the result, arrange professional repair.

Exam trap: Wrong: you fit a higher-rated fuse. Right: if the manual permits replacement, use the same type and current rating; if it blows again, get competent help to find the cause.

Read the full explanation
  • To locate a fault, start by describing what happens, when it began and which conditions reproduce it: starting, braking, turning or connecting the trailer. With the combination stationary, relate the symptom to warning lights, noises, smells, fluid levels and recent work. A noise can have several causes; replacing parts by trial and error can conceal the problem.
  • Follow a checking process from accessible items to specialist checks: consult the manual, look for damage and inspect connections, check fluid levels and note any messages. If several trailer lights fail at once, the connector or its power supply are possible causes that diagnosis must check. Do not carry out tests while driving or clear warnings without retaining the fault information.
  • You can carry out simple tasks intended for the user, such as topping up screenwash, changing a wiper blade or replacing an accessible bulb, if you know the procedure and have the correct replacement part and tools. Disconnect the circuit where appropriate, let parts cool and check their operation afterwards. Sealed or high-voltage modules may require workshop attention.
  • If the manual allows you to replace a fuse, use one of the same type and current rating. If it blows again, you must identify the cause with competent assistance; fitting one with a higher rating or bypassing it removes the protection and can cause a fire.
  • Your ability to carry out minor repairs does not authorise you to improvise on the steering, brakes, structure or coupling lock. Use tools suited to the component, avoid makeshift levers and keep guards in place; if you cannot verify the result, seek professional repair. Diagnosis and simple maintenance work form part of the maintenance knowledge covered by [RGCond, Annex V.B.2, paragraphs 4.º o), 5.º a) and 6.º c)](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#anv).

28ITV and maintenance between inspections

Two inspectors separately check the wheels of a green minibus and its orange luggage trailer, coupled together and parked outside a vehicle inspection station.
The key idea

Check the ITV roadworthiness inspection of your minibus and trailer separately.

five yearsMinibus inspection age threshold
ten yearsLuggage trailer inspection age threshold
six yearsO2 caravan inspection age threshold
two monthsMinor repairs or reinspection maximum
Vehicle and categoryAge from first registration or entry into serviceITV frequency
M2/M3 minibusUp to five yearsAnnually
M2/M3 minibusOver five yearsEvery six months
O2 luggage trailer, O3 or O4 trailerUp to ten yearsAnnually
O2 luggage trailer, O3 or O4 trailerOver ten yearsEvery six months
O2 caravanUp to six yearsExempt
O2 caravanOver six yearsEvery two years

Remember

  • Check each vehicle's expiry date: booking an appointment does not extend validity.
  • A favourable ITV result can still include minor defects.
  • Repair minor defects within two months.
  • After unfavourable or negative results, have reinspection within two months.
  • Place each V-19 sticker on the vehicle it certifies.
  • Inspect within thirty calendar days before expiry to keep your original expiry reference.

Exam trap: Wrong: you continue service with an unfavourable ITV. Right: make only permitted journeys to the workshop or to rectify compliance issues and back to ITV; with a negative result, use external transport.

Read the full explanation
  • Check the ITV (vehicle roadworthiness test) of the minibus and trailer separately. An M2/M3 minibus undergoes an annual inspection up to five years old and a six-monthly inspection when over five; an O2 luggage trailer, O3 or O4 trailer undergoes an annual inspection up to ten years old and a six-monthly inspection when over ten. For an O2 caravan, the specific frequency is exemption up to six years old and an inspection every two years when over six. [RD 920/2017, art. 6](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a6).
  • With a favourable result, you may have minor defects: you must repair them within a maximum of two months. With an unfavourable result, you may only make the journeys permitted by the regulations to a workshop or to have compliance restored and back to the ITV; with a negative result, transport requires means other than the vehicle itself. The reinspection must take place within a maximum of two months. [RD 920/2017, arts. 9 and 11](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a1-3).
  • Place the towing vehicle's V-19 sticker inside, in the upper right-hand corner of the windscreen; on a towed vehicle without a windscreen, place it somewhere clearly visible. Each sticker certifies its own vehicle. [RGV, Annex XI, V-19](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-19). A favourable inspection does not replace keeping the combination safe between inspections.
  • Prepare for the inspection by checking known defects and keep its report for maintenance purposes. Inspection intervals and documents are covered further in «Driver and vehicle combination documentation»; commercial vehicles may undergo roadside technical inspections that detect faults which have developed even if your ITV is valid. [RD 563/2017, arts. 1 and 2](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512).
  • Age is counted from the first registration or entry into service recorded in the Registro de Vehículos (Vehicle Register). You can undergo the periodic inspection within the thirty calendar days before expiry while retaining that expiry date as the reference for calculating the next inspection; booking an appointment does not extend validity. [RD 920/2017, art. 6.1 and 6.5](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a6).

29Preventive maintenance and defect records

A mechanic inspects the wheel of a trailer coupled to a minibus while a supervisor records the inspection on a sheet with pictograms outside a workshop.
The key idea

Follow each vehicle's maintenance plan and record defects.

Remember

  • Adapt checks to the manufacturer's time, use and operating conditions.
  • Include the trailer's own plan.
  • Schedule replacement of fluids, filters and wearing parts.
  • Record date, mileage, defect, repair and checks.
  • Pass information to the workshop and whoever takes over the vehicle.
  • Keep checking even with valid ITV and short journeys.

Exam trap: Wrong: you keep topping up and consider a leak repaired. Right: arrange investigation of the cause and check the repair.

Read the full explanation
  • Organise servicing according to the time, mileage, operating hours and conditions of use specified by the manufacturer. Urban service with frequent stops, loads and work in demanding conditions may require a specific programme; do not invent a single interval for all minibuses. Include the trailer with its own plan, even if you use it with different towing vehicles.
  • Schedule replacement of filters, lubricants, coolant, belts and wearing parts according to the equipment fitted. Also check the battery, exhaust, suspension, brakes and coupling lubrication points. Maintaining fluid levels and replacing worn parts are different tasks: repeatedly adding fluid does not repair a leak or correct wear that servicing must investigate.
  • Record the date, mileage, defect observed, repair and check carried out. Give this information to the workshop and whoever takes over the minibus or trailer at the change of service; an intermittent air leak or a warning that disappears deserves follow-up. Check that the work has been completed before returning the combination to passenger transport.
  • Prevention means intervening before deterioration causes a breakdown, as well as dealing with defects as they appear. Keep up safety checks throughout use, even if the ITV is valid and the journey is short. Preventive maintenance and routine work are included in [RGCond, Annex V.B.2, paragraphs 4.º p) and 5.º a)](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#anv).

Daily walk-round before setting off

Walk around the combination in a consistent order and finish with a functional check.

  1. Secure the combination against movement and check the ground, surroundings and any possible leaks.
  2. Walk along both sides and around the rear: check tyres, inner twin tyres if fitted, wheel rims, lights, reflectors and loose parts.
  3. Check that the coupling is locked, that hoses and connectors are in good condition and that supports are in their transport position.
  4. Check fluid levels according to the manufacturer's instructions, and clean windows, mirrors and lamp lenses.
  5. Adjust your seat and mirrors; check windscreen wipers, washers and dashboard warnings.
  6. If the system uses compressed air, wait for the correct pressure; check lights, door closure and brake response in a safe area.
  7. Rectify safety defects before joining traffic and report those requiring workshop attention.

Checking tyres and twin wheels

Combine measurement with observation; neither replaces the other.

  1. Identify the vehicle category, approved tyres and prescribed pressure for its load and tyre configuration.
  2. With the tyres cold, measure all pressures, including those of the inner tyres, and check valves and valve extensions.
  3. Measure tread depth in the main grooves and examine the full circumference and sidewalls.
  4. On twin wheels, check that the tyres are correctly matched and spaced, with no objects trapped between them.
  5. Check wheel rims and fastenings; arrange safe repairs if you find damage, repeated pressure loss or signs of loosening.

Changing a wheel in a protected location

Only carry out the operation with the necessary training, equipment and safe conditions; follow the combination's manual.

  1. Protect passengers and secure both vehicles against movement on firm, level ground using the specified brakes and wheel chocks.
  2. Prepare a compatible wheel, a jack of adequate capacity, a wheel brace and handling equipment; identify the jacking point.
  3. Loosen the fastenings without removing them while the wheel rests on the ground, then raise the vehicle according to the procedure, without going underneath it.
  4. Remove the wheel, inspect and clean the mounting surfaces; position the replacement wheel and its fastenings without damaging the threads.
  5. Tighten progressively in the prescribed sequence and to the prescribed torque, completing the lowering process according to the manual.
  6. Check the pressure and wheel security, put away the tools and schedule the subsequent tightness check.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1In a bus with a trailer, a basic inspection should include:
2If you notice unusual noises or vibrations in a D1+E or D+E combination, the prudent action is to:
3In a passenger combination with a trailer you should especially check:
4In a D1+E or D+E combination, passengers, load, and the trailer must be:

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module