Theory · C1+E Licence - Light Truck with Trailer · Module 8 of 13

Speed and distances for the vehicle combination

You learn to choose a legal and appropriate speed for your C1+E combination, relate it to stopping distance and apply safe separation distances: following cyclists in urban areas, 50 metres to facilitate overtaking and minimum distances in tunnels.

40 min read26 sectionsReviewed Nov 3, 2026
A light truck towing a trailer travels rightward along a rural road, leaving a wide gap behind the car ahead.
Appropriate speed and safe following distance when towing

1Legal maximum and appropriate speed

A light truck towing a trailer travels in its right-hand lane toward a bend where fog limits visibility.
The key idea

Choose a speed that lets you stop your whole combination before foreseeable hazards.

Remember

  • Do not exceed the legal maximum.
  • Slow down further for rain, your load or poor visibility.
  • You must be able to stop within the clear space you see.
  • Keep your combination’s limits even when empty.

Exam trap: Wrong: keeping within the maximum is always enough. Right: slow down further when conditions require it.

Read the full explanation
  • The maximum speed is a legal ceiling; the minimum prevents you from driving unjustifiably slowly. An appropriate speed lets you control and stop the combination in response to a foreseeable hazard, even if you need to drive well below the maximum. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You can drive at an inappropriate speed without exceeding the permitted figure. For example, 80 km/h on a conventional road can be too fast for your C1 lorry with a trailer in fog, on ice or on a sharp bend. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You must adapt your speed to your physical and mental condition, the condition and characteristics of the road, your vehicle, its load, the weather and traffic. Driving the combination unladen does not allow you to apply the limits for a passenger car. When it is laden, you must assess how it actually responds. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You must be able to stop within your field of vision and before any obstacle that may appear. If the clear distance you can see becomes shorter, slow down until your stopping distance fits within it. Knowing the route does not guarantee that the carriageway beyond a bend or the brow of a hill remains clear. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

2Autopistas and autovías outside built-up areas

A light truck towing a trailer travels in the right lane of a motorway outside a built-up area, with the opposite carriageway separated by a central barrier.
The key idea

Keep your lorry and trailer within the applicable speed limit on an autopista or autovía.

90 km/hGeneral maximum for your combination

Remember

  • The same maximum applies on autopistas and autovías outside built-up areas.
  • Obey any lower limit for the road section, vehicle or transport operation.
  • Apply specific limits for dangerous goods or special transport.

Exam trap: Wrong: a higher sign allows you above 90 km/h. Right: your combination keeps its own maximum.

Read the full explanation
  • With your C1 lorry and trailer or semi-trailer, the general maximum speed on autopistas and autovías (motorways) outside built-up areas is 90 km/h. The table groups lorries, articulated vehicles and motor vehicles towing trailers under this same limit. You must observe any lower limit applicable to the road section, vehicle or transport operation. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • The general maximum speed is the same on autopistas and autovías; if you carry dangerous goods or drive under special transport rules, you must apply their specific limits. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • To answer a scenario involving a 70 km/h limit on an autovía, you must treat 70 as the ceiling for that section and slow down further if necessary. A sign showing a speed above the maximum for your category does not in itself authorise you to exceed the 90 km/h limit for the combination. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

3Conventional roads and roads reserved for motor vehicles

A light truck towing a trailer travels behind a passenger car without overtaking in the right-hand lane of a conventional road in a Mediterranean landscape.
The key idea

Keep your combination within its limit even when the road looks wide and safe.

80 km/hGeneral maximum outside built-up areas

Remember

  • This also applies to conventional roads reserved for motor vehicles.
  • A wide hard shoulder or extra lanes do not raise your maximum.
  • Physical separation between directions does not raise your combination’s maximum either.
  • Obey any lower applicable limit.
  • Do not exceed your maximum to overtake.

Exam trap: Wrong: physical separation allows you 100 km/h. Right: your combination remains limited to 80 km/h, unless a lower limit applies.

Read the full explanation
  • Outside built-up areas, the general maximum speed for your ordinary combination on a conventional road is 80 km/h. You also apply it if the road has a wide arcén (hard shoulder), a good surface or several lanes in your direction. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • The option of setting a 100 km/h limit on a conventional road with physical separation between opposing directions applies to the categories expressly listed in article 48, which do not include your goods vehicle combination. The maximum of 80 km/h continues to apply to you, unless a lower limit applies. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • On a conventional road reserved for motor vehicles, your C1 lorry with a trailer has a general maximum speed of 80 km/h, unless a lower limit applies. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • With your C1 lorry and trailer, you cannot overtake a passenger car maintaining 90 km/h on that road: it already exceeds the maximum speed you can reach. Nor can you exceed 80 to overtake a lorry travelling at 80. Needing to complete a manoeuvre quickly does not authorise you to exceed the speed limit. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

4Unpaved roads

A green light truck towing an orange trailer travels to the right along an unpaved road with potholes, ruts and stones in a rural Mediterranean landscape.
The key idea

Drive slowly on unpaved roads and check whether your combination may enter.

30 km/hMaximum on unpaved roads

Remember

  • Check the surface: calling a road a track does not determine its limit.
  • Slow down further for potholes, dust, gravel or slopes.
  • With dangerous goods, obey this maximum and any lower restriction too.

Exam trap: Wrong: subtract 10 km/h here for dangerous goods. Right: obey 30 km/h and any lower applicable restriction.

Read the full explanation
  • On an unpaved road, your maximum speed limit is 30 km/h. This limit applies because the road is unpaved, not simply because it is called a track. You must check the road surface and any specific signs, as well as whether your combination is allowed to enter. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • Those 30 km/h do not guarantee safe driving over potholes, ruts, dust or loose gravel. You may need to drive much more slowly to maintain grip and control of the whole combination. The load, gradient and space available to pass oncoming road users may require you to slow down further. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • If you carry dangerous goods on an unpaved road, you must observe the 30 km/h limit and any lower restriction that applies. The 10 km/h reduction in article 48.1.b refers to the table in paragraph a. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

5Urban streets: 20, 30 and 50

A light truck towing a trailer travels to the right along a shared-surface urban street, with two pedestrians beside the building frontages.
The key idea

Choose the urban limit by street type, counting only general traffic lanes.

20 km/hCarriageway and pavement share level
30 km/hSingle lane in each direction
50 km/hSeveral lanes in each direction
StreetGeneral maximum if access permitted
Carriageway and pavement at the same level20 km/h
One general traffic lane in each direction30 km/h
Two or more general traffic lanes in each direction50 km/h

Remember

  • Check that your combination may enter.
  • Do not count reserved bus lanes.
  • Obey lower signed limits.
  • Exceptionally, municipal signs can raise single-lane streets to 50 km/h.
  • Slow down further or stop if there is danger.

Exam trap: Wrong: count the bus lane to raise your limit. Right: with one general traffic lane per direction, the general maximum is 30 km/h.

Read the full explanation
  • On an urban road where the carriageway and pavement are at the same level, the general maximum speed is 20 km/h. On an urban road with a single lane in each direction, it is 30 km/h. On an urban road with two or more lanes in each direction, it is 50 km/h. These limits also apply to your combination when you are authorised to drive it along the street. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • To determine the urban limit, you must count only general traffic lanes. With one general traffic lane and one bus-only lane in your direction, the general maximum speed is 30 km/h. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • The municipal authority may lower urban limits using specific signs. Exceptionally, it may raise the limit on a road with a single lane in each direction to 50 km/h, also using specific signs. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • On a shared surface, among access points and with pedestrians nearby, even 20 km/h can be inappropriate. You must adjust your speed to the distance you can see and the space occupied by the whole combination. The general figure does not replace your obligation to stop if circumstances require it. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)

6Stretches of road through towns and motorways in built-up areas

A light truck towing a trailer travels to the right in its lane on a through road between houses with tiled roofs.
The key idea

Distinguish through roads from urban motorways to choose the correct limit.

50 km/hThrough road: general maximum
80 km/hUrban motorway: general maximum
90 km/hYour ceiling after signed increase
Road in built-up areaGeneral maximum for your ordinary combination
Through road50 km/h
Autopista or autovía80 km/h

Remember

  • Obey any other applicable restriction.
  • Adjust your speed before entering each section.
  • A signed increase on urban motorways does not remove your vehicle category’s maximum.

Exam trap: Wrong: an urban increase to 100 lets you reach that speed. Right: your ordinary combination cannot exceed 90 km/h.

Read the full explanation
  • On a travesía (the stretch of road through a town), your general maximum speed is 50 km/h, unless another limit applies. The limit may be lowered by agreement between the municipal authority and the road authority, using specific signs. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • On autopistas and autovías within built-up areas, the general maximum speed is 80 km/h. You need to consider the location and road type to choose the correct limit. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • The maximum speed on these autopistas and autovías may be raised by agreement between the municipal authority and the road authority, using specific signs, without exceeding the general maximum for your category outside built-up areas. For your ordinary combination, the corresponding ceiling is 90 km/h. An increase allowing traffic to travel at 100 does not give you that maximum. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • When you move from a conventional road to a stretch of road through a town and then to an urban street with one lane in each direction, adapt your speed in advance to each set of limits. Your combination must already be travelling at the appropriate speed when each section begins. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)

7Dangerous goods

A light truck towing a trailer with flammable goods placards travels in its right-hand lane on a rural road.
The key idea

When carrying dangerous goods, apply their specific maximum speeds and any lower limit.

10 km/hReduction of interurban maximums
80 km/hAutopista or autovía: non-urban maximum
70 km/hConventional road
40 km/hThrough road or multi-lane street
RoadMaximum for your combination carrying dangerous goods
Autopista or autovía outside built-up areas80 km/h
Conventional road outside built-up areas70 km/h
Through road40 km/h
Urban: two or more lanes in each direction40 km/h
Urban: one lane in each direction30 km/h
Carriageway and pavement at the same level20 km/h

Remember

  • Do not subtract ten from every urban limit.
  • If special transport rules also apply, follow both sets of rules and your authorisation.

Exam trap: Wrong: subtract ten from every urban limit. Right: apply the relevant table maximum and any lower restriction.

Read the full explanation
  • If your combination carries dangerous goods, you must reduce the maximum speeds outside built-up areas shown in the table for your vehicle by 10 km/h. This gives 80 km/h on autopista or autovía outside built-up areas and 70 km/h on conventional roads. These are limits for this type of transport, not recommendations you can ignore in good visibility. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • You must also comply with any lower signed limit and the specific conditions of the transport operation. The baseline for your goods vehicle combination is 90 on autopista or autovía and 80 on conventional roads. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • On urban roads with two or more lanes in each direction and on stretches of road through towns, the specific maximum for dangerous goods is 40 km/h. On a street with only one lane in each direction, you must observe the generic 30 km/h limit, and on a street where the carriageway and pavement share a single level, 20. The 40 km/h limit comes from article 50.4; the 30 and 20 km/h limits are the generic limits in article 50.1. Do not subtract ten from urban limits. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50) [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • Dangerous goods transport and special transport are different conditions: the former depends on the nature of the load, while the latter may require authorisation because mass or dimension limits are exceeded. If both apply, you must comply with both sets of limits and the conditions of the authorisation. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

8Special transport and testing

A light truck towing a trailer with a strapped-down crate maintains a large gap behind the car ahead on a clear rural road.
The key idea

Check your authorisation: special transport and testing have their own conditions.

70 km/hGeneral authorisation: maximum
60 km/hSpecific authorisation: maximum
50 mMinimum gap: special transport groups
150 mVisibility ahead and behind
Authorisation for combination under special transport rulesMaximum speed
General70 km/h
Specific60 km/h
ExceptionalAuthorised speed, never above 60 km/h

Remember

  • Obey stricter restrictions on your ITV technical card.
  • In groups 1, 2 and 3, keep the stated gap.
  • Stop travelling in hazardous weather or without the minimum visibility ahead and behind.
  • A special testing permit allows up to 30 km/h above general maximums.
  • This applies only along the specified route.
  • It excludes urban roads, through roads and sections with specific speed signs.

Exam trap: Wrong: ordinary exceptions apply to the special transport 50 m gap. Right: follow annex III’s specific conditions for groups 1, 2 and 3.

Read the full explanation
  • If you drive your combination under the special transport rules, you must consult its authorisation and Annex III. For the group of vehicles operating under these rules, a general authorisation allows a maximum of 70 km/h and a specific authorisation 60 km/h; an exceptional authorisation sets the authorised speed, which must not exceed 60 km/h. Any stricter restrictions on the ITV (vehicle roadworthiness test) card take precedence. [RGC, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii) [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • Under the common conditions in Annex III for groups 1, 2 and 3, you must keep at least 50 m behind the vehicle ahead. You must also stop travelling if weather conditions create a risk or if you do not have at least 150 m of visibility both ahead and behind. These are specific rules: do not automatically apply the exceptions to the ordinary 50 m rule to them. [RGC, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii) [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • With a special testing permit, you may exceed generic maximum speeds by up to 30 km/h only on the specified route. You may not do so on urban roads, stretches of road through towns or sections with specific speed signs. This permission does not come with your C1+E licence and is not an exception you can use for ordinary commercial transport. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

9Signs, restrictions and the speed limiter

A light truck towing a trailer travels in the right-hand lane of a road approaching a temporary roadworks warning sign and cones.
The key idea

Obey all applicable restrictions even when your speed limiter still allows acceleration.

90 km/hN2 speed limiter setting

Remember

  • Obey temporary and variable signs.
  • Follow restrictions applying to you, your vehicle and your load.
  • The lorry’s limiter setting is subject to legal exemptions.
  • Helping to tamper with the limiter is a very serious offence.

Exam trap: Wrong: the limiter always allows you to drive at 90 km/h. Right: obey the applicable road and transport limits.

Read the full explanation
  • You must observe specific signed limits, including temporary and variable limits, and restrictions imposed on you as the driver, your vehicle or its load. If several applicable restrictions coincide, you must comply with all of them. A general speed sign does not remove a restriction specific to your combination. [RGC, art. 47](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a47) [RGC, art. 52](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a52)
  • The speed limiter on your category N2 C1 lorry is set to prevent you from exceeding 90 km/h, subject to the applicable legal exemptions. Its installation and checking are covered in «Maximum dimensions and masses», in the section «Speed limiter on a C1 lorry». [RD 1417/2005, arts. 4 and 7](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a4)
  • The limiter acts on your vehicle; your permitted speed also depends on the road and the type of transport. On a conventional road, you must observe the limit for your combination even if the device still allows you to accelerate. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • If you take part in or help with installing or activating components that tamper with the limiter, you commit a very serious offence. [Traffic Act, art. 77.m](https://www.boe.es/buscar/act.php?id=BOE-A-2015-11722#a77)

10General minimum speeds for the combination

An orange light truck towing a green trailer travels in the right lane of an empty motorway with carriageways separated by a central barrier.
The key idea

Keep above the general minimum unless you have a justified reason to drive more slowly.

60 km/hMinimum: autopistas and autovías
40 km/hConventional road: ordinary combination minimum
Road: general rules for your ordinary combinationMaximumMinimum without justified reason
Conventional road, including roads reserved for motor vehicles80 km/h40 km/h
Unpaved road30 km/h15 km/h
Urban: carriageway and pavement share a level20 km/h10 km/h
Urban: one lane in each direction30 km/h15 km/h
Urban: several lanes in each direction50 km/h25 km/h
Through road50 km/h25 km/h

Remember

  • On other roads, use half your vehicle category’s generic limit for that road.
  • Use the generic maximum for that road type.
  • Also obey a signed minimum where one exists.
  • Do not drive below the minimum without justification, even on empty roads.
  • Never maintain a minimum speed if it creates danger.

Exam trap: Wrong: halve your maximum to find the autovía minimum. Right: its general minimum is 60 km/h, unless there is a justified reason.

Read the full explanation
  • On autopistas and autovías, the general minimum speed for motor vehicles is 60 km/h, including for your ordinary combination. This minimum has its own fixed value for these roads and allows the justified exceptions provided for in the regulations. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • On other roads, your general minimum speed is half the generic speed limit of your vehicle category on that road. With your ordinary combination on a conventional road, the limits are a maximum of 80 and a minimum of 40 km/h. On a conventional road reserved for motor vehicles, you must apply the same reference, rather than the motorway minimum. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • On an unpaved road with a generic maximum of 30 km/h, half is 15 km/h. On urban roads subject to the ordinary generic limits, the maximum/minimum pairs are 20/10, 30/15 and 50/25 km/h. On an ordinary stretch of road through a town with a generic maximum of 50, your minimum reference is 25. These minimum speeds do not require you to drive unsafely. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • Article 49 uses the generic limit for your category and the road as its basis; you must also observe a signed minimum where one exists. The prohibition on driving below the minimum without justification applies even when no other vehicles are travelling on the road. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)

11When you can drive below the minimum

A light truck towing a trailer travels in its right-hand lane behind a queue of cars, with both rear hazard lights on the trailer illuminated and the shoulder clear.
The key idea

Drive below minimum if traffic, your vehicle or the road prevent higher speeds without risk.

3,500 kgLorry MMA threshold

Remember

  • Traffic, ice, poor visibility or a breakdown can justify slowing down.
  • During regulated escort work, adapt your speed to the escorted vehicle.
  • Use hazard lights if you cannot reach the minimum and risk a rear-end collision.
  • With your heavy lorry, normally keep right on the carriageway.
  • Slow progress alone does not require you to use the hard shoulder.

Exam trap: Wrong: move onto the hard shoulder just because you are slow. Right: with your lorry’s MMA above 3,500 kg, stay on the carriageway; hard shoulder use is reserved for emergencies.

Read the full explanation
  • You may drive below the minimum when traffic, your vehicle or the road prevents you from maintaining a higher speed safely. A queue, ice, insufficient visibility or a breakdown may justify this. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • The regulations also provide for special vehicles, special transport and protection or escort duties, where you adapt your speed to that of the vehicle you are accompanying. Your justification comes from the circumstances or the service provided for by the regulations. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • If you cannot reach the required minimum and there is a risk of a rear-end collision, you must drive with your hazard warning lights on. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • With your C1 lorry with an MMA (maximum authorised mass) above 3,500 kg, you must continue on the carriageway, normally on the right: driving slowly alone does not require you to move onto the arcén (hard shoulder), which you may use only for emergency reasons. The duty to use it when an emergency forces you to drive at an abnormally low speed and seriously disrupts traffic applies to vehicles with an MMA not exceeding 3,500 kg, such as a car. [RGC, art. 31](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a31) [RGC, art. 36](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a36)

12People, animals and nearby access points

A light truck towing a trailer is stopped before a zebra crossing where an adult and a child are crossing on a street with entrances to homes.
The key idea

Slow down before places where people or animals may appear.

Remember

  • Slow down for pedestrians present or likely to enter your path.
  • Take extra care with children, older people and people who struggle to move.
  • Slow near cycles, markets, schools and crossings without traffic lights or an officer.
  • Slow for animals and buildings opening directly onto your part of the road.
  • Slow when approaching a stopped bus, especially a school bus.
  • Outside built-up areas, slow near immobilised vehicles, recovery services and roadside cycles.

Exam trap: Wrong: wait until a pedestrian enters the road. Right: slow down if you can foresee them entering, and stop if necessary.

Read the full explanation
  • You must slow down and, if necessary, stop when pedestrians are on the part of the road you are using or you can reasonably expect them to step into it. Pay particular attention to children, older people, blind people and people with reduced mobility. From your cab, you may have a good view into the distance while still having nearby areas that are difficult to see. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • You must slow down as you approach cycles, roads reserved exclusively for cycles, their junctions and pedestrian crossings without traffic lights or an officer controlling them. You must also do so near markets, educational establishments and places where you can expect children. You must be ready to respond before anyone enters the path of your towing or towed vehicle. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • You must drive at a moderate speed when animals are present or you can foresee them entering the road, and on sections with buildings opening directly onto the part of the road you are using. You must anticipate hazards at an access point hidden by a vehicle or structure. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • As you approach a stopped bus, especially a school bus, you must slow down. Outside built-up areas, you must also do so when approaching vehicles immobilised on the carriageway, roadside assistance services and cycles on the carriageway or hard shoulder. Stay alert for people who may be hidden from view, and avoid letting the size of your combination reduce your safety margins. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)

13Junctions, narrow sections and visibility

A light truck towing a trailer travels in its right-hand lane with its brake lights illuminated before a narrow bend where a rocky hillside limits visibility.
The key idea

Slow down enough to stop when space or visibility is limited.

50 km/hSigned junction: virtually no visibility

Remember

  • Slow near level crossings, roundabouts, junctions without priority and narrow sections.
  • At a signed junction with virtually no visibility, do not exceed 50 km/h.
  • Obey lower limits and slow further if needed to stop.
  • Allow for your trailer’s space when passing oncoming vehicles.
  • If dazzled, slow down and stop if necessary.
  • Unrepairable lighting fault en route? Slow enough to stop within the lit area.

Exam trap: Wrong: pass every junction at 50 km/h. Right: this ceiling concerns signed junctions with virtually no visibility; slow further if necessary.

Read the full explanation
  • You must slow down as you approach level crossings, roundabouts and junctions where you do not have priority, and at narrow sections or where visibility is reduced. You may need to stop to meet this requirement. No single speed guarantees that you can negotiate all these places safely: it depends on the road layout, traffic and actual visibility. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • If a junction is properly signed and visibility along the road is virtually non-existent, you must not exceed 50 km/h. This figure is a specific maximum, not a recommended speed for negotiating the junction. If another limit is lower or you need to drive more slowly to be able to stop, you must meet that more restrictive requirement. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • When meeting an oncoming vehicle, you must slow down if the available space, the vehicles' characteristics or the weather prevent you from doing so safely. With a long combination, a tight bend may leave little lateral clearance. You must also allow for the space needed by the towed vehicle and stop if you cannot continue safely. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • If you are dazzled, you must slow down and even stop if necessary. In dense fog, heavy rain, snow, dust or smoke, you must adjust your speed to what you can actually see. Having priority or your lights on does not allow you to travel beyond the distance you can see to be clear before you stop. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • If a fault that cannot be repaired during your journey forces you to drive with reduced lighting intensity, you must slow down until you can stop within the illuminated area. You must relate the range of your lights to your total stopping distance, including reaction distance. This precaution does not replace the measures required for a breakdown that prevents you from continuing safely. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107)

14Rain, wind, bends and descents

A light truck towing a trailer travels in the right-hand lane in the rain and keeps a wide gap behind the car ahead.
The key idea

Adjust your speed before a bend, descent or change in weather.

Remember

  • In rain or on slippery roads, slow down and increase your following gap.
  • Avoid spraying water or gravel onto other road users.
  • Expect gusts when leaving tunnels or sheltered places.
  • Choose your speed for a bend before entering it.
  • Consider how your load and its distribution affect stability.
  • On long descents, use a suitable gear and the manufacturer’s recommended braking assistance.

Exam trap: Wrong: wait until entering a bend to choose your speed. Right: slow beforehand for visibility, road surface, bend and load.

Read the full explanation
  • In rain or on a slippery road surface, you must slow down and increase the gap to the vehicle ahead. You must also slow down wherever you may spray water, gravel or other material onto other road users. The risk is not just loss of grip: the movement of your combination may harm those nearby. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46) [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You must adapt your speed to the wind and gusts, especially with a tall or long combination. Anticipate changes in exposure as you leave a tunnel or a sheltered area. Slow down in advance and use smooth control inputs; you do not need to wait until you notice a significant deviation before correcting your course. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You must choose your speed for a bend before entering it, taking account of visibility, the bend's radius, the road surface and your load. A high centre of gravity and a poorly distributed load can impair stability. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • On a long descent, you must maintain a speed you can control and leave a margin for braking. As technical guidance, select a suitable gear and use the available auxiliary braking in accordance with the manufacturer's instructions to avoid overloading the service brake. Detailed operation of retarders and trailer brakes is covered in «Braking the trailer and the vehicle combination». [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

15Slowing down without causing rear-end collisions

A light truck towing a trailer travels in the right lane with the trailer’s brake lights illuminated, clear space before the cars ahead and a car following behind.
The key idea

Before slowing sharply, check traffic and warn others, unless danger is imminent.

Remember

  • Check your mirrors while keeping attention on the road ahead.
  • Start slowing early when you see a queue.
  • Avoid sudden braking that could cause a rear-end collision.
  • Whenever possible, warn with repeated brake lights or the prescribed arm signal.
  • For imminent danger, act without waiting to complete a warning.

Exam trap: Wrong: brake suddenly because following drivers must keep their distance. Right: unless danger is imminent, check you can slow safely and warn beforehand.

Read the full explanation
  • Except in imminent danger, before slowing down considerably you must check that you can do so without putting other drivers at risk and give advance warning. You must avoid a sudden reduction in speed that could cause a rear-end collision. The driver behind you has a duty to keep a safe distance, but you still have a duty to anticipate. [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)
  • You must use your mirrors to check traffic behind you as you prepare to slow down significantly, while keeping your attention on the road ahead. When you see a queue, start adjusting your speed with plenty of room instead of waiting until you reach its tail. The combination's length and response make this anticipation especially valuable. [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)
  • Whenever possible, you must warn others of your intention to stop or brake considerably by repeatedly activating the brake lights or using the prescribed arm signal. Article 109 also regulates the use of hazard warning lights when you are immobilised on an autopista or autovía (motorway), or where visibility is significantly reduced. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109) [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)
  • If an imminent danger arises, you must act to avoid it: the exception allows you to respond as necessary without waiting to complete an advance warning. Your aim is to preserve space ahead and make your reduction in speed predictable for those driving behind you. [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)

16Speed when passing vulnerable road users

A light truck towing a trailer overtakes a cyclist in the left lane of a divided rural road, leaving a wide lateral gap.
The key idea

When overtaking vulnerable road users, combine the required side gap with the required speed.

20 km/hMinimum reduction outside built-up areas
1.5 mMinimum side gap
CaseConditions when passing with your combination
Overtaking vulnerable road users outside built-up areasAt least 20 km/h below the road limit and 1.5 m side gap
Vehicle immobilised by breakdown, accident, or emergency, assistance or maintenance service; occupying all or part of your laneAt least 20 km/h below the road limit and 1.5 m side gap; use the opposite lane if needed

Remember

  • Take extra care with pedestrians, animals, animal-drawn vehicles, mopeds, personal mobility vehicles and cyclists.
  • Outside built-up areas, slow before starting and throughout the overtake.
  • Stay at least 20 km/h below the road limit throughout that manoeuvre.
  • Leave 1.5 m minimum; occupy some or all of adjacent or opposing lanes.
  • With several lanes per direction, change lanes completely.
  • Also obey your combination’s maximum and slow further if necessary.

Exam trap: Wrong: a side gap is enough without slowing. Right: meet both requirements in these cases; the immobilised-vehicle rule does not cover traffic queues.

Read the full explanation
  • When overtaking pedestrians, animals, animal-drawn vehicles, mopeds, personal mobility vehicles, cyclists or groups of cyclists, you must take extra care. Outside built-up areas, you must drive at least 20 km/h below the road's speed limit before starting and throughout the manoeuvre. [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)
  • You must combine this reduction with the maximum speed for your combination and a speed appropriate to the circumstances. If the road has a 70 km/h limit, the maximum resulting from the reduction is 50 km/h. If safety requires a lower speed, you must slow down further; subtracting this amount does not automatically make the manoeuvre safe. [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)
  • You must leave at least 1.5 m of lateral clearance and use part or all of the adjacent lane or the lane for oncoming traffic; where there is more than one lane per direction, you must change lanes completely. Lateral clearance and reduced speed are simultaneous requirements, not options you can choose between. [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)
  • When passing a vehicle stopped for a breakdown, an accident or an emergency, assistance or maintenance service listed in article 88, which occupies all or part of your lane, you must leave at least 1.5 m of lateral clearance and drive at least 20 km/h below the road's speed limit. This does not amount to a rule for passing a queue stopped by traffic. [RGC, art. 88](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a88) [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)

17Reaction time and reaction distance

The driver of a light truck towing a trailer notices a fallen branch in his lane while holding his foot above the brake pedal without pressing it yet.
The key idea

You already travel some distance while reacting, before you apply the brake.

Remember

  • Measure from noticing the need to brake until you apply the brake.
  • With the same reaction time, doubling speed doubles your reaction distance.
  • Tiredness, distractions and alcohol can delay your response.

Exam trap: Wrong: reaction distance starts when you press the brake. Right: you travel it before applying the brake.

Read the full explanation
  • From the moment you perceive the need to brake until you apply the brake, you travel your reaction distance. For the same reaction time, if you double your speed, you travel twice as many metres; tiredness, distractions or alcohol can delay your response. [DGT, Manual II, reaction and stopping](https://sede.dgt.gob.es/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2024/Manual-II-Cuestiones-de-Seguridad-Vial-2024.pdf)

18Braking distance of the combination

A light truck towing a trailer travels to the right with its brake lights illuminated and a long stretch of clear road ahead in a Mediterranean landscape.
The key idea

As your speed increases, you need much more space to brake.

Remember

  • Measure from applying the brake until you stop.
  • Consider your speed, load, brakes, tyres and road grip.
  • With comparable slowing, doubling speed makes braking distance about four times as long.

Exam trap: Wrong: doubling speed only doubles braking distance. Right: with comparable deceleration, it approximately quadruples.

Read the full explanation
  • From the moment you apply the brake until you stop, you travel your braking distance. You must take account of speed, load, brakes, tyres and grip; with comparable deceleration, doubling your speed approximately quadruples this distance. [DGT, Manual II, braking distance](https://sede.dgt.gob.es/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2024/Manual-II-Cuestiones-de-Seguridad-Vial-2024.pdf)

19Stopping distance or total stopping distance

A green light truck towing an orange trailer travels in its right-hand lane, with consecutive blue and orange bands representing reaction and braking distances within the clear visible stretch before a bend.
The key idea

Add reaction distance and braking distance to find where you can stop.

Remember

  • Include the distance you travel before pressing the brake.
  • Add the distance you travel while braking.
  • Slow until the total fits within the clear space you can see.

Exam trap: Wrong: stopping distance starts when you press the brake. Right: include the distance travelled while reacting too.

Read the full explanation
  • To calculate your stopping distance, you must add your reaction distance and your braking distance. Adjust your speed so that this entire distance fits within the clear space you can see ahead. [DGT, Manual II, reaction and stopping](https://sede.dgt.gob.es/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2024/Manual-II-Cuestiones-de-Seguridad-Vial-2024.pdf) [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • The operation of the brakes and braking techniques for your combination are covered in «Braking the trailer and the vehicle combination».

20Safe following distance to prevent rear-end collisions

A light truck towing a trailer maintains a wide gap behind a car travelling ahead in the same lane on a wet road in the rain.
The key idea

Leave enough space to stop if the vehicle ahead brakes suddenly.

5 mUrban cyclist: same lane minimum

Remember

  • Increase your gap with higher speed, less grip or poorer visibility.
  • If someone enters your gap, restore it gradually without dangerous braking.
  • On urban roads, keep at least 5 m behind a cyclist in your lane.
  • Increase that gap if you need more space to stop without hitting them.
  • On gravel, increase your gap to protect your windscreen from flying stones.

Exam trap: Wrong: one fixed gap suits every situation. Right: obey applicable minimums and increase your margin for the conditions.

Read the full explanation
  • Whenever you drive behind another vehicle, you must leave enough space to stop without colliding if it brakes suddenly. You must pay particular attention to speed, grip and braking capability. Apart from situations with specific minimum distances, article 54 does not set a single distance in metres that applies to every situation. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • You must increase the gap as speed increases, grip worsens or visibility decreases. Spray from the vehicle ahead can make it harder for you to spot a traffic queue. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • If another vehicle moves into the gap you have left, you must gradually restore a sufficient distance without causing those behind you to brake dangerously. Your duty to avoid a rear-end collision remains even when another road user’s manoeuvre reduces the gap. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On urban roads, if you follow a cyclist in the same lane, you must leave a longitudinal gap of at least 5 m. Increase this gap whenever you need to in order to stop without hitting the cyclist. [RGC, art. 153.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a1-6) [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On loose gravel, you must increase your following distance to reduce the risk of stones thrown up by the vehicle ahead damaging your windscreen. You must also adjust your speed to the reduced grip and avoid throwing up material onto other road users. This gap depends on the conditions; there is no universal figure beyond any applicable minimum distances. [RGC, arts. 45 and 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)

21The 50-metre gap to facilitate overtaking

A light truck towing a trailer travels in the right-hand lane of a rural road and leaves a large gap behind the car ahead, while another car follows it.
The key idea

Leave space for others to overtake you and return safely ahead.

50 mMinimum additional following gap
3,500 kgMMA: must exceed this threshold
10 mLength: must exceed this threshold

Remember

  • Exceeding either the MMA threshold or total length threshold is enough.
  • Your lorry qualifies through its MMA, even when empty.
  • Apply the minimum when following without signalling an intention to overtake.
  • Outside built-up areas: one lane each way, overtaking permitted, and traffic allowing overtaking.
  • Leave more space if you need it to avoid a collision.

Exam trap: Wrong: use the journey’s load to decide. Right: use MMA; exceeding 3,500 kg or total length of 10 m is enough when you follow without signalling to overtake, outside built-up areas, on a road with one lane each way where overtaking is permitted and traffic allows it.

Read the full explanation
  • As well as leaving enough space to avoid a collision, if you follow another vehicle without signalling your intention to overtake, you must leave enough space for a driver behind to overtake you safely. For vehicles with an MMA (maximum authorised mass) over 3,500 kg and vehicles or combinations with a total length over 10 m, you must maintain a minimum gap of 50 m to allow this overtaking manoeuvre. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • You only need to meet one of the criteria: an MMA over 3,500 kg or a total length over 10 m. You must use the MMA, rather than the payload or the weight of the goods on that journey. Your C1 lorry with a trailer falls under this rule because of the lorry’s MMA, even when it is empty and even when the combination does not exceed 10 m in length. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On a road outside a built-up area with one lane in each direction, where overtaking is permitted and traffic conditions allow it, you must maintain this minimum gap if you do not signal your intention to overtake. With an 11 m combination, its length alone is enough for the rule to apply. The space allows another driver to overtake you and return safely to your lane ahead of you. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • The 50 m is a minimum for this gap, rather than a distance that is always sufficient. If your speed, rain or braking capability means you need 70 m to avoid a rear-end collision, you must leave at least that greater gap. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)

22Exceptions to the ordinary 50-metre rule

A light truck towing a trailer maintains a wide gap behind a car in the right lane of a motorway with two lanes in each direction and a central barrier.
The key idea

Even without the additional gap, keep enough space to avoid a collision.

50 mAdditional gap with exceptions
Case: ordinary gap to allow overtakingAdditional gap required for your combination?
Built-up areaNo
Overtaking prohibitedNo
More than one lane in your directionNo
Traffic too congested for overtakingNo

Remember

  • This additional gap is not required in built-up areas.
  • Nor where overtaking is prohibited or several lanes run in your direction.
  • Nor when traffic is too congested to allow overtaking.
  • Always keep enough space to avoid a collision.
  • Signalling an intention to overtake does not remove that safety margin.
  • Do not apply these exceptions to tunnels or special transport.

Exam trap: Wrong: follow as closely as you like where overtaking is prohibited. Right: keep enough stopping space, even if that exceeds 50 m.

Read the full explanation
  • You do not have to leave the additional gap to facilitate overtaking in built-up areas, where overtaking is prohibited, where there is more than one lane in your direction or when traffic is so congested that overtaking is impossible. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On a motorway with two lanes in your direction, you are not automatically required to leave a minimum of 50 m simply because you drive a long combination. You must maintain enough space to stop without colliding. The road’s maximum speed limit or traffic occupying the right-hand lane does not remove this basic duty. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On a road where overtaking is prohibited, outside a tunnel and with no other specific minimum, you must leave the gap you need to avoid a rear-end collision, even if it exceeds 50 m. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • Signalling your intention to overtake does not remove the need for a gap to avoid a collision either. In addition, the exceptions in article 54.3 do not apply to the specific minimum distances in tunnels or to the following distance required for special transport. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)

23Tunnels and underpasses: 150 metres or six seconds

A green light truck towing a trailer travels in the right-hand lane of a tunnel, leaving a large gap behind the car ahead.
The key idea

In tunnels, keep your heavy lorry’s required gap when you do not intend to overtake.

150 mMinimum for your heavy lorry
six secondsAlternative minimum time gap
3,500 kgMMA: threshold you exceed
Vehicle not intending to overtake: tunnel or underpassMinimum distance or minimum time
Your lorry: MMA above 3,500 kg150 m or six seconds
Other vehicles100 m or four seconds

Remember

  • Use these references in tunnels and underpasses when you do not intend to overtake.
  • You may use distance or time as alternatives.
  • Start counting when the rear of the vehicle ahead passes a fixed point.
  • Finish when your vehicle’s front reaches that point.
  • Several lanes in your direction do not remove this minimum.
  • Also keep any margin required by safety and signs.

Exam trap: Wrong: choose 100 m or four seconds for your heavy lorry. Right: without intending to overtake, keep at least 150 m or six seconds.

Read the full explanation
  • With your C1 lorry, whose MMA exceeds 3,500 kg, you must maintain at least 150 m or a minimum interval of six seconds behind the vehicle ahead in tunnels or underpasses when you do not intend to overtake. The general distance of 100 m or four seconds applies to other vehicles; you must not choose it for your heavy combination. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • You must maintain this gap while driving, as well as any margin required by safety and signs. The regulations give distance in metres and a time interval as alternative measures. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • To check the interval, choose a fixed point: count from when the rear of the vehicle ahead goes past it until the front of your vehicle reaches it. If you use the time interval for your combination, you must allow at least six seconds. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • This requirement still applies when there are several lanes in your direction if you do not intend to overtake. If you actually carry out a permitted overtaking manoeuvre, you must still maintain the gap needed to avoid a collision. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54) [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)

24Adapting your speed to a tunnel

A green light goods truck with an orange trailer is stopped before the stop line at a red traffic light at a tunnel entrance.
The key idea

Adapt your speed to the tunnel’s signs, lighting and traffic.

Tunnel, underpass or section with a tunnel signOvertaking
One lane in your directionProhibited
Several lanes in your directionPermitted without entering the opposing lane and subject to other overtaking bans

Remember

  • Combine the road limit, your combination’s limit and the signs.
  • Slow before entering if visibility or traffic requires it.
  • Do not enter if the traffic lights prohibit passage.
  • Obey tunnel displays and instructions.
  • Use the necessary lights in tunnels and underpasses at any time.

Exam trap: Wrong: overtake by entering the opposing lane inside a tunnel. Right: overtake only with several lanes in your direction, without entering the opposing lane, and obey all other overtaking bans.

Read the full explanation
  • These articles do not set a single maximum speed that replaces all other limits whenever you enter a tunnel. You must take account of the type of road, the maximum speed for your combination and the tunnel signs together. Slow down in advance if lighting, traffic or visibility makes it inappropriate to maintain your speed from outside the tunnel. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • You must obey traffic lights, variable message signs and instructions given over loudspeakers or by other means. You cannot enter if the traffic light at the entrance prohibits entry; the regulatory exception for emergency, assistance and maintenance teams does not authorise you to enter when carrying out ordinary transport. [RGC, art. 96](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a96) [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • You must use the appropriate lights in tunnels and underpasses at any time of day. If visibility changes as you enter, adjust your speed to maintain control within the space you can see. Details of lighting devices are covered in «Safety devices for the vehicle combination». [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98) [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • You must not overtake in tunnels, underpasses or stretches covered by the «Tunnel» sign (S-5) where you have only one lane in your direction. With more than one lane in your direction, you may overtake without entering the opposite direction and while complying with all other prohibitions. Do not move your combination closer to the vehicle ahead to prepare for a prohibited manoeuvre. [RGC, art. 87.1.d](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a87)

25Traffic queues inside a tunnel

A light truck towing a trailer is stopped in the right lane of a tunnel, with its hazard warning lights and position lights on and a large gap to the car ahead.
The key idea

If you stop inside a tunnel, switch off the engine and keep the position lights on.

Reason for stopping in the tunnelWhat you must do
Traffic queueStay inside with your passengers
Breakdown, fire or other emergencyFollow the specific procedure and tunnel instructions

Remember

  • Slow down progressively and stop as far as possible from the vehicle ahead.
  • When traffic makes you stop, switch on hazard lights temporarily.
  • Keep the position lights on and always switch off the engine when stopped.
  • After more than two minutes, keep the engine off and position lights on.
  • During a traffic queue, stay inside with your passengers.
  • For a breakdown, fire or other emergency, follow the specific procedure and tunnel instructions.

Exam trap: Wrong: leave the engine running because you remain at the wheel. Right: always switch it off when stopped inside a tunnel and keep the position lights on.

Read the full explanation
  • If you see a traffic queue inside a tunnel, you must slow down progressively and avoid continuing to close the gap until the last moment. If traffic conditions force you to stop, you must stop as far as possible from the vehicle ahead. This instruction concerns stopping because of traffic and does not set a separate numerical minimum for all cases. [RGC, art. 97](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a97)
  • When stopped in these circumstances, you must switch on your hazard warning lights temporarily to warn those approaching from behind and keep your position lights on. You and your passengers must remain in the vehicle when traffic is the reason for stopping. [RGC, art. 97.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a97)
  • When stopped inside a tunnel or enclosed place, you must always switch off the engine, even if you remain at the wheel [RGC, art. 115.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a115); if the wait lasts more than two minutes, keep the engine off and keep the position lights on until you resume driving [RGC, art. 115.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a115).
  • If you stop because of a breakdown, fire or another emergency, you must follow the specific procedure in “Dealing with accidents and breakdowns” and follow the tunnel instructions. Here you must recognise the difference between a traffic queue and an emergency: the reason for stopping determines how you protect yourself and whether you must leave the vehicle. [RGC, art. 97](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a97)

26Lanes with specific speed limits

A light truck towing a trailer with its dipped headlights on travels in a temporary lane separated by cones from oncoming traffic, beside a carriageway closed for roadworks.
The key idea

Check the special speed limits for the lane you are using.

80 km/hMaximum on these lanes
60 km/hMinimum on these lanes
Lane used by your vehicle combinationSpeed limits, unless lower limits are set or signed
Opened to traffic in the opposite direction because of roadworksMinimum 60 km/h; maximum 80 km/h
Temporary additional lane, or hard shoulders opened beside itMinimum 60 km/h; maximum 80 km/h
Adjacent normal-direction lane: only one lane remains in your directionMinimum 60 km/h; maximum 80 km/h
Adjacent normal-direction lane: several lanes remain in your directionGeneral limits for your vehicle combination and the road

Remember

  • Follow any lower limit set or specifically shown by signs.
  • Roadworks lanes opened to opposite traffic have their own limits.
  • Temporary extra lanes and open hard shoulders beside them have the same limits.
  • Adjacent normal-direction lane: keep to 60–80 km/h if only one lane remains for you.
  • With several lanes remaining, apply general limits for your combination and the road.
  • Check «Reserved and special lanes» for access and lighting rules.

Exam trap: Wrong: always use the general limits in the normal-direction lane beside an opposite-direction lane. Right: with one lane left, use 60 to 80 km/h or any lower set or signed limit; with several lanes left, use the general limits for your vehicle combination and the road.

Read the full explanation
  • When you drive in a lane opened to traffic in the opposite direction to normal because of roadworks, in a temporary additional lane or on the arcén (hard shoulder) opened to traffic alongside it, the maximum speed is 80 km/h and the minimum is 60 km/h, or the lower limits established or specifically indicated by signs. [RGC, art. 41.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41) [RGC, art. 42.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a42)
  • In the lane running in the normal direction alongside the lane opened to traffic in the opposite direction, the same range of 60 to 80 km/h applies if you have only one lane left in your direction; if you have several lanes left, apply the general limits for your combination and the road. You study access to these lanes and their lighting requirements in “Manoeuvres with a light lorry and trailer”, in the section “Reserved and special lanes”. [RGC, art. 41.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41)

Choosing the speed of the combination

Consider the road, vehicle, transport operation and actual conditions together.

  1. Identify whether you are outside a built-up area, on an urban road, on a stretch of road through a town or on an autopista or autovía within a built-up area.
  2. Apply the maximum for your combination: 90/80 outside built-up areas; 30 on unpaved roads; 20/30/50 on streets, depending on their layout; 50 on stretches of road through towns and 80 on autopistas or autovías within built-up areas.
  3. Check for dangerous goods, special transport, restrictions specific to your combination and signs.
  4. Check the minimum speed and whether you have a justified reason to drive below it.
  5. Slow down as much as necessary to stop within the distance you can see and keep the combination under control.

Choosing the longitudinal separation distance

Maintain a safe separation distance and observe the applicable minimum distances.

  1. Assess the distance you need to avoid a collision if the vehicle ahead brakes sharply.
  2. On urban roads, if you follow a cyclist in the same lane, leave at least 5 m and increase the gap as safety requires.
  3. If you do not signal your intention to overtake, check the ordinary 50 m rule for an MMA (maximum authorised mass) over 3,500 kg or a total length over 10 m.
  4. Check its exceptions: built-up areas, overtaking prohibited, more than one lane in each direction or traffic congestion that prevents overtaking.
  5. In a tunnel or underpass, if you do not intend to overtake, maintain 150 m or six seconds for your heavy combination.
  6. Check signs and specific rules, and leave a larger gap whenever safety requires it.

Anticipating a traffic queue

Slow down while maintaining the gap ahead and avoiding surprises for traffic behind.

  1. Spot the queue and check the traffic behind while keeping your attention on the road ahead.
  2. Whenever possible, warn others that you are slowing down significantly, and reduce speed progressively.
  3. Leave enough distance to stop the whole combination.
  4. If a queue brings you to a standstill in a tunnel, stop as far as possible from the vehicle ahead, switch on your hazard warning lights temporarily, keep the position lights on and switch off the engine.
  5. Stay in the vehicle if you are stationary because of traffic and follow the tunnel instructions.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module