Theory · C1+E Licence - Light Truck with Trailer · Module 7 of 13

Safe, well-distributed loads

You learn to position, distribute and secure goods on your C1 lorry with a trailer or semi-trailer, within the 12,000 kg MMA (maximum authorised mass) limit for the C1+E combination. You study stability, lashings, moving loads, partial deliveries and loading and unloading operations, as well as covers and preventing material from falling onto the road. This includes the limits for projecting indivisible loads, protecting their ends and marking them with V-20 panels, lights and reflectors.

43 min read24 sectionsReviewed Nov 3, 2026
A light truck with a trailer travels to the right along a rural road with crates distributed across both platforms and secured with orange straps.
Evenly distributed and securely restrained cargo

1A secure load throughout the combination

A light truck towing a trailer travels in the right-hand lane with low loads distributed across both beds and secured with tie-down straps.
The key idea

You must secure the lorry and trailer loads to keep control.

Remember

  • Secure the goods, covers, bars and chocks.
  • Prevent the load dragging, falling or moving dangerously.
  • Keep the lights and both lorry and trailer registration plates visible.
  • Keep the V-6 sign visible when the vehicle or combination exceeds 12 m.
  • Check the load and coupling before setting off.
  • Secure cab objects and keep your view and movement clear.

Exam trap: Wrong: Packages staying still when parked proves safety. Right: Secure them for braking and turning.

Read the full explanation
  • You must prepare the C1 lorry and its trailer or semi-trailer as a system: the goods alter the balance of each vehicle and the forces transmitted through the coupling. A lower mass than that of a large combination does not prevent load movement or overturning. Packages remaining still while the vehicle is parked does not prove that they are secured for braking or turning.
  • You must prevent the goods and their accessories from dragging, coming loose or moving dangerously, impairing stability or causing avoidable noise, dust and nuisance. This obligation also covers chocks, tarpaulins, bars and other items used to position or protect the load. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14)
  • You must keep lights, signs, plates and compulsory markings visible, without obstructing hand signals. On your combination, the load, its lashings and the cover must leave visible both the trailer's own registration plate and the plate displaying the lorry's registration number, as well as the V-6 long-vehicle sign when the vehicle or combination is more than 12 m long. Check the final arrangement with the doors and cover closed. [RGC, art. 14.1.d](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14) [RGV, annex XVIII, III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826) [RGV, annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6)
  • You must check that the goods are secured and the coupling is safe before setting off; the mechanical sequence is covered in «Safe coupling and uncoupling».
  • You must maintain your field of vision and freedom of movement to drive. If you carry tools or small packages in the cab, position and secure them so that they do not interfere with the controls or become projectiles. The load body or trailer provides cargo space, but you must not use it in a way that allows the goods to compromise control of the combination. [RGC, art. 18](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a18)

2Plan stowage before loading

A worker measures a machine and consults a sheet showing drawings of the cargo beside boxes, load-spreading boards and straps, in front of a light truck with a trailer and empty flatbeds in a loading yard.
The key idea

You must plan where each package goes and how to secure it.

Remember

  • Check each package’s weight and size.
  • Check its shape, fragility and where its weight is concentrated.
  • Check the strength of the floor, supports and anchorage points.
  • Provide supports that spread the weight where needed.
  • Plan how the remaining load will sit after each delivery.

Exam trap: Wrong: Adding straps afterwards fixes any arrangement. Right: Plan positioning and securing together.

Read the full explanation
  • You must know the mass, dimensions, shape and fragility of the packages before deciding where to position them. Also identify the centre of gravity when it does not coincide with the geometric centre, as with some machines. A bulky box may weigh less than a small piece of metal.
  • You must check that the floor, supports and lashing points are suitable for the goods. A concentrated load may exceed the floor's local strength even when the total mass is permissible. Plan to use load-spreading plates or supports when the design of the platform and the load itself requires them.
  • You must decide the loading order with deliveries in mind. Removing the first packages must not leave a dangerous load distribution or render the blocking of the remaining packages ineffective. Planning only the journey to the first recipient is insufficient if you then continue with some of the goods.
  • You must choose positioning and restraint together: where each item rests, which spaces remain empty and which components prevent movement. Annex III requires you to consider axle load distribution and the strength of the components used for securing; adding straps at the end cannot correct every stowage error. [RD 563/2017, annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3)

3Keep the centre of gravity low and central

A light truck towing a trailer travels along a rural road with heavy blocks below and light boxes above, distributed across both sides of the beds and secured with straps.
The key idea

You must keep heavy goods low and spread weight evenly to reduce overturning.

Remember

  • Put heavy packages below lighter ones.
  • Spread weight between both sides according to your loading plan.
  • Respect packaging strength when stacking.
  • Give upper packages a stable base.
  • Prevent goods sliding or tipping.
  • A level vehicle body does not prove balanced weight.

Exam trap: Wrong: Strong lashings prevent overturning with a high load. Right: Keep the weight low.

Read the full explanation
  • You must place the heaviest items as low as possible. A high centre of gravity reduces the lateral force needed to overturn: on a bend or roundabout, you may lose stability on a path that you could negotiate with the same load positioned lower. Lashing prevents the goods from moving, but does not eliminate this risk of the vehicle overturning. [RGC, art. 14.1.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14)
  • You must distribute the load evenly between both sides, within the load plan. A centre of gravity offset to one side reduces the margin against overturning towards the more heavily loaded side; the risk changes with the direction of the bend or manoeuvre. The suspension may keep the body apparently level without correcting this imbalance. [RGC, art. 14.1.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14)
  • When stacking, you must respect the strength of the packaging and provide a stable base for the upper packages. As a stowage guideline, place heavy items beneath light ones and avoid small or uneven supports. Crushed packaging may loosen a top-over lashing and allow the entire stack to move.
  • You must prevent both sliding and tipping of the goods themselves. A tall machine may tilt even if its base does not move across the floor; you need a system suited to its geometry. The requirement to prevent longitudinal and transverse tilting forms part of the load-securing principles. [RD 563/2017, annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3)

4Distribute mass between the axles

A light truck with a central-axle trailer and secured, distributed crates is stationary with each axle on a weighing platform in an inspection area.
The key idea

You must respect weight limits for the combination, each vehicle and each axle.

12,000 kgMaximum combination MMA
10 %Vertical cap: trailer maximum mass
1,000 kgOther vertical load cap
Towed vehicle or caseWhat you must check
Semi-trailerSome weight passes through the fifth wheel to the towing vehicle.
Centre-axle trailerRespect the documented vertical load: never exceed the lower of 10 % of its maximum mass or 1,000 kg.
Centre-axle trailer: excess weight forwardYou may overload the coupling and the lorry’s rear axle.
Centre-axle trailer: excess weight rearwardYou may unload the coupling and reduce stability.

Remember

  • The maximum authorised mass includes the vehicles and their load.
  • Respect towing and coupling capacities too.
  • Use the manufacturer’s diagram: the body’s geometric centre may be outside its permitted area.
  • Respect minimum and maximum axle loads.
  • If you do not know the distribution, weigh each axle before setting off.
  • Recheck distribution when you change vehicles or move goods.

Exam trap: Wrong: You can carry 12,000 kg of goods. Right: That authorised maximum includes vehicles and load.

Read the full explanation
  • You must comply simultaneously with the MMA (maximum authorised mass) of the combination, that of each vehicle, the axle or axle-group limits, and the technical and towing capacities. For C1+E, the combination's MMA must not exceed 12,000 kg; this figure includes the vehicles and their load and does not represent a payload of 12,000 kg. Even when the total mass is permissible, you may overload an axle. [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4) [RGV, annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826)
  • You must use the manufacturer's load distribution diagram when available. It shows you where the goods' centre of gravity may be located according to their mass. The geometric centre of the load body may lie outside the permissible area shown on the diagram.
  • With a semi-trailer, you must consider that part of the load is transmitted to the towing vehicle through the kingpin and fifth wheel. Moving goods forwards or backwards changes the distribution between the towing vehicle and the semi-trailer's axles. Concentrating them next to the headboard or at the rear end may overload different areas.
  • You must maintain the minimum loads required on the axles as well as keeping within their maximum limits. A distribution that removes too much load from the steering or driven axles impairs control and the ability to transmit forces to the ground. Annex III requires you to observe maximum and minimum loads within the MMA. [RD 563/2017, annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3)
  • If you do not know the actual distribution, you must check it by appropriately weighing individual axles or axle groups and correct the positioning before setting off. Weighing only the whole combination does not reveal every local overload. Reassess whenever you change the towing vehicle, the towed vehicle or the distribution of the goods.
  • You must observe the documented vertical load, which for a centre-axle trailer never exceeds the lower of these values: 10 % of its maximum mass or 1,000 kg. [RGV, annex IX, 4.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#A4-3) Concentrating too much weight at the front may overload the coupling and the lorry's rear axle; concentrating it at the rear may unload the coupling and impair stability. You must follow the load distribution plan.

5Split the load without creating overloads

A light truck with a trailer travels along a road with boxes distributed in a single layer and secured with straps on both load beds.
The key idea

You must split divisible goods without exceeding any capacity of the combination.

Remember

  • Spread goods according to the lorry’s and trailer’s capacities.
  • You do not need equal weight in each vehicle.
  • Remove some goods if you cannot meet every limit.
  • Count occupants, fuel, tools and accessories already on board.
  • Check axles, towing and coupling before adding goods.
  • Do not count weight transferred to the towing vehicle again as spare capacity.

Exam trap: Wrong: More lashings allow more weight. Right: Securing goods does not increase authorised capacity.

Read the full explanation
  • If the goods are divisible, you must distribute the items between the usable areas and, in a road train, between the lorry and trailer, according to their capacities. Splitting the load does not necessarily mean allocating the same mass to each vehicle: their capacities and the distances between supports may differ.
  • You must avoid trying to resolve a total overload by piling the goods over another axle that also becomes overloaded. Correcting it requires a plan that meets all limits simultaneously; sometimes you must remove part of the consignment. Lashing holds the load in place, but does not increase the authorised capacity.
  • Consult the axle and axle-group limits, including tri-axle groups, in «Maximum dimensions and masses»; projecting loads and their marking are explained in «Projecting loads and protecting their ends», at the end of this module.
  • To calculate how much you can add, you must start with the actual mass of the vehicle ready for service, including the occupants, fuel, tools and accessories already on board. The difference up to the applicable limit is only an initial margin: you then check axle loads, towing limits and the coupling. You must not count the mass transmitted by the semi-trailer to the towing vehicle twice as available capacity.

6Forces the securing system must withstand

A light truck towing a trailer brakes on a rural road, with palletized crates secured by taut straps and resting against the platforms’ front bulkheads.
The key idea

You must secure goods against forces from braking, turning and emergencies.

0.8Forward force factor
0.5Side and rearward factor
Force directionForce your securing system must withstand
ForwardsLoad weight multiplied by 0.8.
Towards each sideLoad weight multiplied by 0.5.
BackwardsLoad weight multiplied by 0.5.

Remember

  • Prepare the securing system for braking and changes of direction.
  • Calculate equipment needs using weight, friction, angles and overturning risk.
  • Do not use a fixed number of straps for every load.
  • Keep goods secure in emergencies and when moving off uphill.

Exam trap: Wrong: The factors allow some goods to remain unsecured. Right: They specify required securing strength.

Read the full explanation
  • You must allow for inertia making the load tend to keep moving when you brake and tend to move sideways when you change direction. Preventing it from falling off while travelling straight at a constant speed is not enough: the restraint must also work during demanding manoeuvres.
  • The system must withstand a forward force equivalent to the weight of the load multiplied by 0.8, a force to each side multiplied by 0.5 and a rearward force multiplied by 0.5. You must understand these factors as strength requirements for the securing system, without interpreting them as percentages of mass that you may leave unsecured. [RD 563/2017, annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3)
  • You must design the system to account for all the forces, supports and resistance involved. There is no universal number of straps suitable for every pallet or machine. Mass, friction, angles and the possibility of tipping determine which equipment you need and how much of it.
  • You must maintain restraint in emergencies and when moving off uphill too. An inspection may check that changes in position are minimal and that the load cannot leave its loading space. The excuse of driving slowly does not replace this requirement. [RD 563/2017, art. 11](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#a1-3)

7EN standards and choosing a method

A light truck with a trailer is parked beside the right-hand kerb, with crates on a pallet secured by timber blocking and two straps anchored to the trailer platform.
The key idea

You must choose securing standards, equipment and methods suited to your load.

StandardWhat you use it for
EN 12195-1Calculating lashing forces
EN 12195-2Synthetic fibre straps
EN 12195-3Chains
EN 12195-4Steel wire ropes
EN 12640Lashing points
EN 12642Vehicle body strength

Remember

  • Follow the securing plan and equipment instructions.
  • Check that the structure withstands the forces transmitted by lashings.
  • You can combine locking, blocking, direct lashing and top-over lashing.
  • Secure the container to the vehicle and the goods inside the container.

Exam trap: Wrong: Fixing the container secures its contents. Right: Secure the goods inside too.

Read the full explanation
  • EN 12195-1 is the standard for calculating lashing forces cited in Annex III. EN 12195-2, EN 12195-3 and EN 12195-4 cover synthetic fibre straps, chains and steel wire ropes respectively. Each item of equipment must be suitable for the load and its intended use. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3)
  • To choose a structure capable of withstanding the lashing forces, you must refer to the standards cited in the annex: EN 12640 for lashing points and EN 12642 for vehicle body strength. A strong strap is insufficient if you attach it to a component that cannot withstand the force transmitted. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3)
  • You can combine methods: locking, blocking, direct lashing and top-over lashing. You must choose a combination whose effectiveness can be justified for the particular goods. A container lock works differently from a strap that presses a pallet against the floor. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3)
  • You must follow the securing plan and the equipment instructions, without improvising equivalents between systems. Securing a container to the platform does not prove that its contents are immobilised; you need to ensure restraint at every level, from the goods to the vehicle carrying them.

8Block movement with strong supports

A light truck with a trailer carries pipes secured with straps and blocked by metal supports and chocks bolted to the deck, beside a reinforced headboard.
The key idea

You must block the load with supports strong enough to prevent movement.

Remember

  • Use strong supports and stops suited to the goods.
  • Reduce gaps that allow dangerous movement.
  • Check the strength of walls, doors and supports.
  • Do not treat a side curtain as a strong wall.
  • Secure cradles or chocks for goods that can roll.
  • Add the necessary lashings and avoid damaging the goods.

Exam trap: Wrong: Any filling material works as a stop. Right: Use material strong enough for expected forces.

Read the full explanation
  • When blocking a load, you must prevent it from moving by using strong components: headboards, spacers, bars, stanchions, wedges or suitable recesses. Position the goods and supports so that the force is transmitted to a structure capable of withstanding it, without relying on substantial movement beforehand.
  • You must reduce any gaps that are incompatible with the blocking system. An empty space allows a package to gather momentum before striking the next package or the wall. Use fillers suited to the expected forces; a soft material that protects surfaces does not automatically serve as a strong stop.
  • You must check which forces the headboard, walls and doors are certified to withstand. Do not assume that every enclosed body restrains the entire load or that a side curtain acts as a structural wall. Annex III requires you to take account of the strength of the components used for securing. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3)
  • For pipes, coils and other items that can roll, you must provide suitable cradles or chocks and secure them, together with the necessary lashings. A round item can roll even without sliding. Prevent the chocks from moving and check that the support does not damage or deform the goods.

9Use friction in a controlled way

A light truck with a trailer travels along a rural road carrying a tall crate on supports with green anti-slip mats, secured by two over-the-top tie-down straps.
The key idea

You must check surface grip and combine it with the securing needed.

Remember

  • Check for dust, oil, water or scraps between surfaces.
  • Place suitable anti-slip material where the load rests.
  • Check its condition and follow the securing plan.
  • Use a justified friction value when calculating lashings.
  • Recheck calculations if the surfaces in contact change.
  • Check the overturning risk of tall or narrow loads too.

Exam trap: Wrong: Heavy goods cannot slide. Right: Check friction and secure them against movement.

Read the full explanation
  • Friction lets you use the resistance to sliding between surfaces in contact. You must assess the materials and their actual condition: dust, oil, water or packaging debris can affect grip. The weight of the goods alone does not guarantee that they remain still during braking.
  • You can use suitable anti-slip material between the load and the floor or between layers, in accordance with the securing plan. You must position it at the points of support and check its condition. You cannot assume that a damaged or incorrectly positioned mat, or one subjected to unsuitable pressure, is effective.
  • You must use a justifiable friction value to calculate the lashings; do not choose one based on how the surface looks. Top-over lashing uses additional pressure to increase friction. If the actual contact between materials changes, you must review the calculation and the planned solution.
  • Improving friction can prevent the base from moving forwards, but a tall or narrow unit still needs stability against tipping. Assess both risks and combine anti-slip material with blocking or lashing where appropriate.

10Top-over lashing and direct lashing

A light truck towing a trailer carries a machine secured by green straps passing over the load and orange direct lashings between its eyes and the platform anchors.
The key idea

You must understand how lashings work and which data you need for calculations.

Method or dataWhat you must remember
Top-over lashingPresses goods against their support to increase friction.
Direct lashingResists movement according to capacity and direction.
LCLashing capacity.
STFStandard tension force.

Remember

  • For top-over lashing, pass the strap over the load and tighten it.
  • For direct lashing, connect suitable load and vehicle points.
  • Follow the angles in your securing plan.
  • Check that packaging can withstand tightening.
  • Read the equipment data and instructions.
  • Do not judge effectiveness just by counting visible straps.

Exam trap: Wrong: LC and STF mean the same. Right: Distinguish lashing capacity from tension force.

Read the full explanation
  • With top-over lashing, you must take the securing element over the load and tension it towards the anchorage points to press the load against its support. Its main function is to increase friction. You need to consider the pretension transmitted, the angle and the strength of the packaging, as well as the number of lashings.
  • With direct lashing, you must connect suitable points on the load to those on the vehicle so that the securing elements resist movement in the intended directions. Their effectiveness depends on their capacity and orientation. An arrangement that restrains forward movement may need additional measures to restrain sideways or rearward movement.
  • You must read the equipment data: LC identifies the lashing capacity and STF the standard tension force. These quantities are not interchangeable in calculations. A high lashing capacity does not mean that the tensioner applies that same force when tightened over a pallet. You must check these details on the equipment identification and in the instructions for use; they are technical selection criteria, not permission to exceed mass limits.
  • You must observe the angles specified in the lashing plan. If a top-over lashing lies at too shallow an angle, the force component pressing the load against the floor decreases; with direct lashing, what matters is the part of the force that opposes movement. Do not replace a calculation with a count of the straps visible from outside.

11Look after straps, anchorage points and packaging

A worker checks the straps anchored to a light truck’s trailer, securing a pallet of stretch-wrapped boxes and passing over protective corner pieces.
The key idea

You must use sound lashings and check anchorage points and packaging too.

Remember

  • Inspect equipment before use.
  • Set aside damaged items or those without enough identification.
  • Follow the manufacturer’s withdrawal criteria.
  • Protect straps from sharp edges and goods from damaging pressure.
  • Attach hooks to points designed to withstand the force.
  • Check connections between packages and their securing to the vehicle.

Exam trap: Wrong: Pallet wrapping lashes goods to the vehicle. Right: Secure that connection too.

Read the full explanation
  • You must inspect straps, stitching, chains, wire ropes, hooks and tensioners before use. Set aside damaged items or those whose identification does not allow you to check their performance, and follow the manufacturer's withdrawal criteria. Do not repair a cut with a knot or deal with deformed parts by making an improvised adjustment.
  • You must protect lashing equipment from edges that could cut it and protect the goods from pressure where necessary. Edge protectors help distribute forces, but they must be compatible with the system. Each protector must remain in place and stable during the journey to perform its function.
  • You must attach hooks to points designed to withstand the force, without leaving a hook resting insecurely or forcing catches and ratchets. The strength of the securing assembly is limited by its components and connections; you cannot determine it solely from the strap's label.
  • Wrapping film or pallet banding alone does not constitute lashing to the vehicle. Check both how the packages are held together and how the complete unit is secured to the floor. If the packaging breaks, the packages can come loose even if the pallet remains secured.

12Check the load during the journey

A driver wearing a reflective vest inspects a cargo strap ratchet on a trailer coupled to a light truck, with both units parked beside the kerb in a rest area.
The key idea

You must check the load before setting off and during the journey.

Remember

  • Check supports, gaps, tensioners, doors and covers on both vehicles.
  • Stow loose straps and tools.
  • Recheck lashings after goods settle and at suitable stops.
  • After heavy braking or an incident, stop safely and inspect.
  • Fix causes of noise, tilting or loose tensioners before continuing.
  • Do not wait for goods to fall out before recognising danger.

Exam trap: Wrong: Every load needs checking after the same distance. Right: Follow the plan and respond to incidents.

Read the full explanation
  • You must inspect the result before moving off: no dangerous gaps, stable supports, closed tensioners and loose strap ends stowed away. Check that there are no loose tools and that doors, tailgates and covers are secured. Your inspection must cover both units of the combination.
  • As a safety practice, you must check the lashings again once the goods have settled and at appropriate stops during the journey, in accordance with the transport plan. Some loads compress or vibrate and lose pretension. There is no single inspection distance suitable for all goods and equipment.
  • You must check the restraints after heavy braking, any movement you notice or an incident that could have affected the stowage, stopping in a safe place. If you detect tilting, an unusual noise or a loose tensioner, you must resolve the cause before continuing; tightening without inspecting can conceal a broken support.
  • You must take a deficiency seriously even if the goods are still inside. Annex III distinguishes between securing that needs improvement, inadequate securing with a possibility of significant movement or tipping, and a direct danger to traffic or people. An inspection may assess tensions, calculations and certificates as well as looking at the load. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3)

13Partial deliveries and opening doors

A worker checks the ratchet tensioners on two secured and blocked pallet loads in a trailer coupled to a light truck, with part of the floor empty after a partial delivery.
The key idea

You must recheck weight distribution and securing after every partial delivery.

Remember

  • Check remaining weight and gaps after removing packages.
  • Replace supports and lashings removed during unloading.
  • Before opening doors, check whether goods are pressing against them.
  • Stand outside the path of falling goods.
  • Do not use your body to stop a door under pressure.
  • When unloading an uncoupled trailer, check ground, supports and balance throughout.

Exam trap: Wrong: Less load always means greater safety. Right: Recheck distribution and lashings.

Read the full explanation
  • After removing load units, you must check the mass distribution and blocking again. You may leave a gap between units that previously supported each other or concentrate the remaining mass at one end. Driving with less weight does not guarantee safer distribution.
  • You must reinstate any lashings and supports removed for unloading, following a plan suited to the remaining load. You must also assess any load units moved temporarily to reach others.
  • Before opening doors or releasing restraints, you must consider whether the goods are resting against them or have shifted. Stand clear of the path of any falling load and follow the equipment's safe operating procedure. Do not use your body to stop a door that is under pressure.
  • If you leave the trailer or semi-trailer detached for loading or unloading, you must check that its supports, the ground and the load distribution keep it stable throughout the operation. On a centre-axle trailer, moving goods or driving equipment into it can greatly affect its longitudinal balance. Use only supports designed to withstand these conditions and follow the manufacturer's procedure.

14Liquids and surge

A light truck towing a tank trailer travels in the right-hand lane of a rural road, with a cutaway showing liquid sloshing inside the partially filled tank.
The key idea

You must expect liquid movement to change the combination’s balance.

Remember

  • Plan ahead for braking, acceleration and bends.
  • Use the controls smoothly.
  • Take extra care with a partially filled tank.
  • Avoid sudden corrections that increase rocking.
  • Know the tank’s compartments and baffles, which limit liquid movement.
  • Adapt your speed to the load and each bend.

Exam trap: Wrong: Baffles remove every force. Right: Expect liquid movement according to the tank’s design.

Read the full explanation
  • When you transport liquid, you must anticipate internal movements that do not occur in a solid load that is properly secured against movement. When you brake, accelerate or change direction, the liquid can move and exert forces on the tank. This movement changes the mass distribution from moment to moment and makes it harder to keep your C1+E combination stable.
  • With a partially filled tank, you must pay particular attention to the space available for the liquid to move. Surging can continue after your initial control input and exert successive forces. You must not respond with abrupt corrections that cause further oscillations.
  • You must know the tank's compartment layout and internal devices. Compartments and baffles can limit movement depending on their design, but they do not eliminate all forces or make the tanker behave like a rigid load. Distribution between compartments also affects axle loads.
  • You must anticipate changes in speed and direction and operate the controls smoothly, especially with a tall or partially loaded tanker. A safe speed depends on the load and each bend; adapt your speed to these conditions. Driving technique is covered in «Driving techniques for vehicle combinations». [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

15Fill and empty tankers in a controlled way

A worker checks the valve and outlet cap of a light tanker truck with a tanker trailer, parked beside the kerb in a service area.
The key idea

You must fill and empty tankers according to the liquid, tank and weight distribution.

Remember

  • Calculate loading using capacity, density, temperature and permitted mass.
  • Respect filling limits and leave the required space for liquid expansion.
  • Do not apply the same filling percentage to every tanker.
  • Plan the order for filling and emptying compartments.
  • After partial unloading, recheck axle weights and remaining liquid movement.
  • Before leaving, check closures, valves, pipes, leaks and outside residues.

Exam trap: Wrong: Fill to the brim to prevent surge. Right: Respect applicable filling limits and permitted mass.

Read the full explanation
  • You must determine the quantity to load using the product and tank data: usable capacity, density, temperature, filling limits and permissible mass. The same volume can represent different masses depending on the liquid. You must not infer the mass from the visible level without knowing these conditions.
  • You must comply with the filling level applicable to the product and equipment and leave the space needed for expansion. You must not fill to the brim as a solution to surging or apply a universal percentage to all tankers. If you transport dangerous goods, you must also comply with their specific regulations.
  • You must plan the order in which you fill or empty compartments to maintain safe distribution. After partial unloading, you must assess axle loads and the behaviour of the remaining liquid. One empty compartment and one loaded compartment do not automatically mean that a tanker is balanced.
  • Before resuming your journey, you must check lids, valves, pipes and closures according to the equipment instructions, and verify that there are no leaks or external residues that could fall off. Details of dangerous goods classification and handling are covered in specialist training; here you must understand and manage the general risks of movement and spillage.

16Hanging loads and live animals

A light truck towing a trailer travels in its right-hand lane, with a cutaway of its cargo box showing three meat carcasses suspended from a rail with a lateral retaining bar.
The key idea

You must expect hanging loads and live animals to move and change balance.

LoadMovement you must expect
Meat hanging from railsSwings when you brake or turn.
Live animalsMove unpredictably and change weight distribution.

Remember

  • Avoid sudden acceleration, braking and turns.
  • Check rails, hooks and restraints when carrying hanging meat.
  • Use suitable partitions and restraints when carrying animals.
  • Do not rely only on the body being closed.
  • Follow the specific animal transport rules too.

Exam trap: Wrong: These loads behave like fixed pallets. Right: Expect the centre of gravity to change.

Read the full explanation
  • If you transport meat carcasses suspended from rails, you must anticipate their swinging when you brake or turn. The goods can shift the centre of gravity sideways and exert forces on the bodywork even when the floor is clear. Check the rails, hooks and restraint systems provided for this transport; do not treat this load like pallets resting on the floor. [RGC, art. 14.1.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14)
  • With live animals, you must anticipate their own unpredictable movements, which change the mass distribution during the journey. As with liquids, the centre of gravity can change while you drive, although the mechanism of movement is different. Avoid abrupt acceleration, braking and turns that encourage shifting and loss of stability. [RGC, art. 14.1.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14)
  • You must use a layout and partitioning and containment equipment suited to the vehicle and the animals you transport. An enclosed body alone does not prevent them from gathering on one side. This module covers the effect on stability; when transporting animals, you must also comply with the specific regulations. [RGC, art. 14.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14)

17Choose the loading and unloading location

A worker moves a box on a hand trolley beside a light truck with a trailer inside a warehouse yard, off the public road, with the pavement and roadway unobstructed.
The key idea

You must load and unload off the road unless using the road is unavoidable.

Remember

  • If using the road is unavoidable, prevent danger and serious disruption.
  • Respect stopping and parking rules.
  • In built-up areas, follow municipal rules on times and places too.
  • Where possible, work on the side nearest the carriageway edge.
  • Prepare enough equipment to work quickly without unnecessary nuisance.
  • Do not put goods on the carriageway, hard shoulder or pedestrian areas.

Exam trap: Wrong: Brief unloading on the road is allowed. Right: It must be unavoidable, safe, without serious disruption, and meet stopping, parking and applicable municipal rules.

Read the full explanation
  • You must load and unload off the road. Only when unavoidable may you do so on the road, without causing danger or serious disruption to other road users. The convenience of stopping beside the customer does not make every point on the road a suitable location. [RGC, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16)
  • If you have to work on the road as an exception, you must comply with the stopping and parking rules. In built-up areas, you must also comply with municipal rules on times and locations. A reserved loading and unloading area does not remove its conditions of use or authorise you to occupy any nearby space. [RGC, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16)
  • You must carry out the operations, wherever possible, on the side of the vehicle nearest the edge of the carriageway. When driving on the right, this is usually the right-hand side; you must take account of the actual vehicle position and authorised location, without encroaching on the traffic area out of habit. [RGC, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16)
  • You must have sufficient resources to carry out the operation as quickly as possible and avoid unnecessary noise and disturbance. You must not place goods on the carriageway, arcén (hard shoulder) or pedestrian areas. Even if pallets are only there for a moment, you must not use these areas for temporary storage. [RGC, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16)

18Prepare the loading bay and operation

A light truck with a trailer is immobilized with wheel chocks beside a loading dock while the driver and a warehouse worker coordinate using hand signals from positions clear of the vehicle combination.
The key idea

You must prepare a stable working area and coordinate before moving goods.

Remember

  • Check ground, space and loading bay or ramp compatibility with your combination.
  • Secure the combination against movement and coordinate with staff.
  • Use the devices provided to prevent accidental movement.
  • Keep away from suspended loads, trapping points and manoeuvring areas.
  • When guiding, agree signals and stop the operation if communication fails.
  • Before leaving, check clear surroundings, removed ramps, closed doors and secure goods.

Exam trap: Wrong: Warehouse permission alone allows departure. Right: Check the load, lights and accessories too.

Read the full explanation
  • Before starting, you must check the strength and levelness of the ground, the working space and whether the loading bay or ramp is compatible with the combination. Anticipate forklift and pedestrian movements. A platform suitable for a different vehicle does not guarantee adequate capacity or geometry for yours.
  • You must immobilise the combination and coordinate the start of the operation with the site's staff. As an operating guideline, use the devices provided to prevent accidental movement or departure while people or equipment are inside. Do not start moving the vehicle until you receive confirmation that the area is clear.
  • You must stay clear of the path of suspended loads, trapping points and the equipment's manoeuvring area. If you act as a spotter, agree clear signals with the operator and stop the operation if you lose communication. Speed does not justify entering a danger area.
  • Before leaving, you must confirm that ramps and equipment have been removed, doors and tailgates are closed and all remaining goods are secure. Also check that the surrounding area is clear. The warehouse's authorisation to leave does not replace your own check of the load, lights and accessories.

19Who may load and unload

A warehouse worker moves a pallet of boxes with a pallet jack beside the open trailer of a light truck, while the driver waits apart beside the cab.
The key idea

You must know who is responsible and when you may take part as the driver.

7.5 tonnesBan threshold: vehicle MMA
Case and scopeRule to check
Goods vehicles over 7.5 tonnes MMA in SpainAs driver, do not take part unless a legal exception applies.
C1 lorry and trailerThe threshold uses each vehicle’s MMA. Your C1 lorry stays below it; a trailer over 7.5 tonnes MMA exceeds it. Exceptions apply wherever the ban applies.
Participation exception above the threshold: parcel services and similar, few packages one person can easily handleYou may take part as driver.
Exception above the threshold: break-bulk unloading, distribution centre to point of saleMeet daily rest or working-hours conditions; be able to return to your usual centre or home.
Exception above the threshold: break-bulk loading and unloading between those points, either directionAlso have a loader-carrier contract lasting at least one year.
Participation exceptions above the thresholdRemovals, storage, tankers, aggregates, tippers, integral cranes or devices, car transporters and recovery vehicles.
Exception above the threshold: live animalsException at control posts approved under EU rules.
Other participation exceptions above the thresholdThose in specific rules or regulations, while ensuring your safety.
General contractual rule for loading and unloadingLoading is the loader’s responsibility; unloading is the consignee’s. The carrier needs a written agreement before presenting the vehicle for loading. The surcharge is invoiced separately from transport.
General contractual rule for stowing and unstowingThese are respectively the loader’s and consignee’s responsibility, unless the carrier expressly takes them on.
Parcel services and similar: few packages one person can easily handle using equipment on boardLoading and unloading: the carrier’s responsibility unless agreed otherwise. Stowing and unstowing: always the carrier’s responsibility. Do not apply this exception to every pallet delivery.

Remember

  • Goods vehicles over 7.5 tonnes MMA: do not take part unless legally exempt.
  • The ban includes load carriers, packaging, containers and cages.
  • Breaking the ban is a very serious transport offence.
  • Check each vehicle’s MMA: your C1 lorry does not exceed the threshold.
  • For break-bulk loads between distribution centres and shops, check every legal condition.
  • A contract does not remove the ban on driver participation.

Exam trap: Wrong: If the carrier agrees to load, you can always take part. Right: Check whether driver participation is prohibited.

Read the full explanation
  • The prohibition on taking part in loading and unloading applies to you as a driver of a ‘goods vehicle with a maximum authorised mass of more than 7.5 tonnes’, subject to the legal exceptions. It includes load supports, packaging, containers and cages, and applies to operations carried out in Spain. The threshold refers to the vehicle's MMA (maximum authorised mass): your C1 lorry does not exceed it; a trailer with an MMA of more than 7.5 t can exceed it. The exceptions apply wherever the prohibition applies. [LOTT, thirteenth additional provision](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#da) [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4)
  • If you take part in breach of this prohibition, you commit a very serious transport regulation offence. The law presumes liability on the part of the company under whose direction you act and the loader, consignor, intermediary and consignee involved. This penalty regime falls under the LOTT. [LOTT, art. 140.41](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#a140)
  • Among the exceptions, you must recognise removals and furniture storage, tankers, aggregates, tipping vehicles or vehicles with cranes or other built-in loading and unloading devices, car transporters and recovery vehicles. Exceptions also cover live animals at control posts approved under EU legislation, transport whose specific legislation provides for different driver participation, and cases established by regulations that ensure your safety. [LOTT, thirteenth additional provision](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#da)
  • You may take part in parcel delivery and similar services that collect or deliver a small number of packages that one person can easily handle. Additional conditions apply to part-load transport between distribution centres and points of sale; you must understand part-load transport as transport requiring prior handling, groupage, sorting or similar operations. [LOTT, thirteenth additional provision, point e)](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#da)
  • You may take part in unloading part-load consignments between a distribution centre and a point of sale if the activity meets the legal conditions concerning daily rest or performance within your daily working hours and allows you to return to your usual operating centre or your home. To take part in loading and unloading between these points, including in the reverse direction, you must also meet the condition that the contract between the loader and the carrier lasts at least one year. [LOTT, thirteenth additional provision, point e)](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#da)
  • As a rule, loading is the loader's responsibility and unloading is the consignee's; for the carrier to take on these tasks, you need a written agreement before the vehicle is presented for loading, with a surcharge invoiced separately from the transport. Stowing and unstowing are respectively the responsibility of the loader and consignee, unless the carrier expressly takes them on. A contract does not remove the prohibition on your participation as a driver where it applies. [Law 15/2009, art. 20](https://www.boe.es/buscar/act.php?id=BOE-A-2009-18004#a20)
  • In parcel delivery and similar services involving a small number of packages that one person can easily handle using the equipment on board, this contractual rule applies: loading and unloading are the carrier's responsibility unless agreed otherwise, and stowing and unstowing are always the carrier's responsibility. You must not extend this exception to every palletised consignment simply because you deliver it to several destinations. [Law 15/2009, art. 20](https://www.boe.es/buscar/act.php?id=BOE-A-2009-18004#a20)

20Covers and bulk goods

A light truck towing a trailer travels in the right-hand lane with both load beds completely covered by intact green tarpaulins secured with short ties.
The key idea

You must completely cover materials that produce dust or may fall off.

Remember

  • Use a complete, effective cover.
  • Check that no dust or material escapes.
  • Avoid heaps that raise the centre of gravity or overload an axle.
  • Respect vehicle capacity.
  • Secure the cover and stow ropes, tensioners and loose ends.
  • Check outside residues and remove them somewhere suitable before leaving.

Exam trap: Wrong: Any tarpaulin is enough. Right: Prevent losses and keep lights, signs and registration plates visible.

Read the full explanation
  • If you carry materials that produce dust or may fall off, you must cover them completely and effectively. You must assess the result, not just whether a tarpaulin is present: a cover that is torn, open at one end or unable to retain the material does not fulfil this function. The obligation covers, for example, sand, soil or debris that may fall off. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14)
  • You must distribute bulk goods without heaps that unnecessarily raise the centre of gravity or concentrate mass on one axle. The tarpaulin retains loose material, but does not increase the authorised mass.
  • You must secure the cover and gather up tensioners, ropes and loose ends so that they do not strike anything, drag or come off. Protective accessories are subject to the same requirements for safe positioning as the load. Check that they do not obscure lights, marking panels or the number plate. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14)
  • Before leaving a building site, quarry or unloading point, you must check the tailgate, edges, load platform and exterior components where loose debris may remain. As a preventive measure, remove it in a suitable place. Prevent an operation that appears complete from turning into a continuous loss of material onto the road.

21Keep the road clean and safe

A worker collects spilled gravel with a shovel and bucket in an area marked by cones beside a light truck with a trailer stopped at the right-hand kerb with its load covered and secured.
The key idea

You must prevent lost loads and deal with road dangers you cause.

Remember

  • Do not throw or leave materials that make traffic unsafe.
  • If you cause an obstruction, remove it promptly and warn others meanwhile.
  • After a spill, stop safely and prevent further material escaping.
  • Request suitable equipment to remove it.
  • Do not spread slippery substances with water or push debris towards others.
  • Fix the cause of the loss before continuing.

Exam trap: Wrong: Cleaning the spill is enough. Right: Fix its cause before continuing too.

Read the full explanation
  • You must not throw, deposit or abandon materials that obstruct traffic, make it dangerous or damage the road. The risk includes large packages as well as aggregates, mud or liquids that affect grip. You must prevent it through loading, securing closures and cleaning the vehicle. [RGC, art. 4.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a4)
  • If you create an obstruction or hazard, you must remove it as soon as possible and, in the meantime, take measures to make other road users aware of it and avoid obstructing traffic. [RGC, art. 5](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a5)
  • If a spill occurs, you must stop the operation or bring the vehicle to a halt safely, prevent any more material from escaping and request suitable equipment to remove it. You must not spread a slippery substance with water or push debris into the path of other road users as an improvised solution.
  • You must check why the material came loose before resuming your journey: a faulty tailgate, a poorly secured cover, broken packaging or inadequate restraint. Cleaning the affected area does not resolve the cause. For protecting an immobilised vehicle and alerting the emergency services, consult ‘Dealing with accidents and breakdowns’.

22Projecting loads and protecting their ends

A light truck towing a trailer carries a beam secured with straps, with its protruding rear end covered by an orange padded sleeve and marked with a red and white striped panel.
The key idea

You must keep goods within the vehicle unless permitted exceptions allow indivisible loads to project.

2 mFront: vehicle over 5 m
3 mRear: vehicle over 5 m
0.40 mMaximum projection each side
2.55 mMaximum width including load
Goods-only vehicles carrying indivisible loads: type and lengthPermitted projection
Indivisible length; vehicle over 5 m longUp to 2 m forwards and 3 m backwards.
Indivisible length; vehicle 5 m long or lessUp to one third of vehicle length at each end.
Smallest load dimension exceeds vehicle widthUp to 0.40 m each side; maximum total width 2.55 m.

Remember

  • An awkward load is not necessarily indivisible.
  • Apply the limit to the vehicle carrying the item.
  • Leave turning space so the load cannot hit the other unit.
  • If its smallest dimension exceeds vehicle width, check both sideways limits.
  • Protect projecting ends even when the load is marked.
  • If special transport authorisation is needed, follow its conditions.

Exam trap: Wrong: Spare width on one side allows more projection opposite. Right: Respect each side and total width.

Read the full explanation
  • As a general rule, you must keep the load within the vehicle's outline when viewed from above. For your C1 lorry with a trailer intended exclusively for goods, the exceptions allowing projection apply to indivisible loads and require safe stowage and preparation. A package being awkward to position does not make it indivisible. [RGC, art. 15.1-2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15)
  • For beams, posts, pipes or other items of indivisible length, you may allow projection of up to 2 m at the front and 3 m at the rear if the vehicle is more than 5 m long. If it is 5 m long or less, the limit at each end, front and rear, is one third of its length. Apply the rule to the vehicle carrying the item; the space between the lorry and trailer must allow turning without the load interfering with the other unit. [RGC, art. 15.2.a](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15)
  • If the smaller dimension of an indivisible load exceeds the width of the goods vehicle, it may project by up to 0.40 m on each side, provided that the overall width, including the load, does not exceed 2.55 m. You must meet both conditions at the same time; having spare width on one side does not allow you to increase the projection on the other. [RGC, art. 15.2.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15)
  • When a load projects within the permitted limits, you must protect its projecting end to reduce the consequences of scraping or collision and take the necessary precautions to prevent harm to other road users. Protecting the end is a separate obligation from marking it: a visible panel does not in itself cushion contact with a rigid item. [RGC, art. 15.5](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15)
  • If you drive under special transport arrangements, you must meet the conditions of the authorisation. The ordinary projection limits do not replace those arrangements where they are required; consult ‘Maximum dimensions and masses’, in its sections ‘Indivisible loads and additional authorisation’ and ‘Special transport conditions’. [RGC, art. 15.8](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15)

23V-20 panel for loads projecting at the rear

A light truck towing a trailer travels on the right and carries beams secured with straps, with a red and white diagonal striped panel fixed to the end of the load projecting beyond the rear.
The key idea

You must display a V-20 panel whenever your load projects at the rear.

Your load’s rear projectionPanels you must fit
Does not cover the full rear widthOne V-20 panel at the rear end.
Projects lengthways across the full rear widthTwo panels, one at each end, with stripes forming an inverted V.

Remember

  • Mark rear projections in daylight and good visibility too.
  • Place the panel at the rear end of the goods.
  • Keep it perpendicular to the vehicle’s length while travelling.
  • Use a regulation reflective panel with red and white stripes.
  • Secure it firmly; do not substitute cloth or cardboard.

Exam trap: Wrong: V-20 is needed only at maximum projection. Right: Use it whenever goods project at the rear.

Read the full explanation
  • Whenever your load projects at the rear, you must mark it with the V-20 panel. Place it at the rearmost end of the goods and keep it perpendicular to the vehicle's longitudinal axis while driving. The obligation also applies by day and in good visibility; it depends on rear projection, not on whether the item reaches the maximum permitted projection. [RGC, art. 15.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15)
  • The V-20 is the regulatory retroreflective panel with red and white stripes for loads projecting at the rear. You must use a sign that meets its technical specifications and secure it firmly: cloth or painted cardboard does not demonstrate these properties. [RGV, Annex XI, V-20](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-20)
  • If your load projects lengthways across the full rear width of the vehicle, you must position two panels transversely, one at each end of the load or of the width of the projecting material. Arrange their stripes to form an inverted V. This arrangement identifies both rear corners of the load you carry. [RGC, art. 15.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15)

24Lights and reflectors for projecting loads

A light truck towing a trailer travels at dusk with an illuminated red lamp and a red-and-white striped panel at the end of its rear-projecting load.
The key idea

You must add lights and, where required, reflectors to make projecting loads visible.

0.40 mSideways threshold: mark when exceeded
Projecting loads: sunset to sunrise or significantly reduced visibilityMarkings you must add
RearRed light.
FrontWhite light.
Sideways: end more than 0.40 m from corresponding position light’s outer edgeEach end: white light and reflector facing forwards; red light and reflector facing backwards.

Remember

  • Add these markings between sunset and sunrise.
  • Also add them when weather or environmental conditions significantly reduce visibility.
  • Keep the rear panel when adding the red light.
  • Measure the sideways threshold from the corresponding position light’s outer edge.
  • Do not confuse this with projection measured from the vehicle.

Exam trap: Wrong: Measure the sideways lighting threshold from the body. Right: Measure from the corresponding position light’s outer edge.

Read the full explanation
  • Between sunset and sunrise, or when weather or environmental conditions significantly reduce visibility, you must add a red light to the markings for a load projecting at the rear. In these conditions, you must mark a front projection with a white light. The lighting helps identify the ends of the goods. [RGC, art. 15.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15)
  • For a load projecting sideways, you must measure the distance from its end to the outer edge of the corresponding front or rear position light. If it exceeds 0.40 m, between sunset and sunrise or when visibility is significantly reduced, you must mark each projecting side end with a white light and white reflector facing forwards, and a red light and red reflector facing rearwards. You measure this threshold from the position lights, whereas you measure the width limit for the projection from the vehicle. [RGC, art. 15.7](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15)

Plan, distribute and secure

Prepare the goods and the combination before moving for the first time.

  1. Identify the mass, dimensions, centre of gravity and delivery order of the packages.
  2. Check the MMA of the C1+E combination, the capacities of each vehicle, the axles, coupling, floor and anchorage points.
  3. Distribute the load low down and evenly according to the loading plan.
  4. Eliminate dangerous movement using blocking, friction and calculated lashings.
  5. Check supports, equipment, fastenings, covers and the visibility of lights and plates.
  6. Check the distribution by weighing if you cannot substantiate it, and correct it before setting off.

Carry out a partial unloading operation

The remaining goods must stay stable and restrained.

  1. Check that the location and the driver's participation comply with the applicable rules.
  2. Immobilise the combination and coordinate the operation with the personnel responsible.
  3. Assess whether the load has shifted before opening doors or removing lashings.
  4. Remove the intended units without destabilising those that remain.
  5. Reassess the axle load distribution and restore the blocking and lashings.
  6. Close up, remove equipment and debris, and check the surroundings before resuming your journey.

Prepare a tanker for the road

Control the mass, distribution and internal movement of the liquid.

  1. Identify the product, its density and the filling conditions for the equipment.
  2. Determine quantities and the order of operations according to the compartments and mass limits.
  3. Carry out the operation with the combination immobilised and with suitable equipment.
  4. Check fastenings and valves, and check for leaks or residue on the outside.
  5. Assess the loading condition and anticipate surge in partially filled tanks.
  6. Reassess the distribution and securing of the equipment after each delivery.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module