Theory · C1+E Licence - Light Truck with Trailer · Module 6 of 13

Safety devices for the vehicle combination

You learn to recognise and check the devices that keep your C1+E combination safe and visible, from the secondary coupling to its lights, number plates, mirrors and protective devices. You master the thresholds and emergency equipment covered in the exam, including wheel chocks, a connected V-16, a high-visibility vest and fire extinguishers.

35 min read25 sectionsReviewed Nov 3, 2026
A person wearing a reflective vest checks the coupling of a light truck and trailer parked beside the kerb, with lights, reflectors, two rear plates and a wheel chock visible.
Checking truck and trailer safety equipment

1Each device has a specific function

A person wearing a reflective vest inspects the rear lights of a trailer attached to a light truck parked beside the kerb, with the coupling and connecting cables visible.
The key idea

Check each safety system on your combination separately.

Remember

  • Check the trailer outside too, in safe conditions.
  • Keep portable equipment secure and easy to reach.
  • Bring the adaptations and protective equipment needed for your test.

Exam trap: Wrong: working lorry lights are enough. Right: check the trailer lights too.

Read the full explanation
  • The mechanical coupling keeps the combination together; automatic braking stops the detached towed vehicle, and signalling allows others to see it. You must check each system separately: the condition of one does not confirm that the others work. [RGV, art. 12](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12). [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • With your light lorry and trailer or semi-trailer, you must also check the towed vehicle. You can receive warnings or see some devices from the cab, but you must supplement this information with an external inspection in safe conditions. Having working lights on the towing vehicle does not prove that the trailer lights work.
  • Portable equipment supplements the permanently installed devices. You must store it securely and accessibly, so that you can locate each item without moving goods and without leaving loose objects in the cab.
  • In C1+E tests, the examiner may check that you have suitable protective equipment where applicable and that you have the necessary corrective aids, prostheses or adaptations. The equipment required corresponds to the protection needed for the test. [RGCond, art. 57.2](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a57). [RGCond, Annex VI, C.1](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#anvi).

2Secondary safety coupling

A light truck and trailer stand immobilized beside the right-hand kerb, with the main hitch separated and a secondary chain keeping the drawbar above the ground.
The key idea

The secondary coupling stops the drawbar falling if the main coupling fails.

1,500 kgMaximum MMA: conditional requirement

Remember

  • Your trailer needs it with MMA up to 1,500 kg and no breakaway braking.
  • You may use a suitable chain, cable or other device.
  • Check its anchor points and routing.
  • If the coupling breaks, stop the combination and arrange repairs.

Exam trap: Wrong: every trailer needs the same chain. Right: a secondary coupling is required for trailers with MMA up to 1,500 kg without breakaway braking.

Read the full explanation
  • If you tow a trailer with an MMA (maximum authorised mass) of no more than 1,500 kg without a system that ensures it brakes if the coupling breaks, it must have a secondary coupling in addition to the main one. The regulations allow a chain, cable or other device that fulfils the required function; the material alone does not identify its purpose. [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • If the main coupling separates, this secondary coupling must prevent the drawbar from touching the ground and retain some residual steering control of the trailer. If the coupling breaks, you must immobilise the combination and arrange the necessary repair. [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • You must not confuse the safety chain with an anti-theft device, an electrical earth connection or a repair to the main locking mechanism. It performs its function when the main coupling fails, so you must check that it has suitable anchorage points and routing for the system fitted.
  • The 1,500 kg limit refers to the trailer’s MMA and applies in conjunction with the absence of the breakaway braking system described. With C1+E, you may encounter trailers with different characteristics: you must identify the solution appropriate to the one fitted, without requiring the same chain on every trailer or semi-trailer. [RGV, art. 13.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).

3Breakaway cable and automatic braking

A person wearing a reflective vest inspects the orange breakaway cable beside the coupling of a light truck and trailer parked in a bay next to the kerb.
The key idea

Automatic braking stops your towed vehicle if it separates while moving.

Towed vehicle systemWhat you check
Breakaway cableAttachment and routing specified by the manufacturer
Air connectionsChecks required for the installed equipment

Remember

  • Attach any breakaway cable where the manufacturer specifies.
  • Allow movement without activating the brake during normal manoeuvres.
  • Check cables, chains, hooks and fastenings.
  • Resolve faults before driving.

Exam trap: Wrong: a chain always applies the brake. Right: identify what the installed system does.

Read the full explanation
  • The automatic braking devices on the trailer or semi-trailer must ensure that it stops automatically if it becomes uncoupled or the coupling breaks while driving. Their operation depends on the braking device fitted and its connection to the towed vehicle’s system. [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • If the equipment uses a breakaway cable that applies the brake on separation, you must attach it to the designated point and follow the routing specified by its manufacturer. Its installation must allow it to operate on separation, without coming loose or being activated by a normal manoeuvre.
  • The emergency system on your C1+E combination depends on the equipment fitted. A cable that activates a brake and a braking system with pneumatic connections require different checks; you must not automatically apply the installation arrangement from one trailer to another. Braking and its circuits are covered in the module «Braking the trailer and the vehicle combination». [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12). [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Visually check the condition of accessible cables, chains, hooks and fastenings, looking for breaks, deformation or incorrect installation. As a safety guideline, resolve any fault before driving and follow the system manual; do not test its operation by causing the combination to separate while moving.

4Connections and safety locks before driving

A person checks the coupling lock and connections between a light truck and its trailer parked in a yard.
The key idea

Before moving, check the coupling lock and all its connections.

Remember

  • Use compatible connections, correctly joined and secured.
  • Resolve any doubts about the lock before moving.
  • Prevent connections dragging, becoming trapped or pulling too tight.
  • Raise and secure the semi-trailer supports before driving.
  • Before uncoupling, prevent movement and leave the semi-trailer properly supported.

Exam trap: Wrong: parts that fit together are compatible. Right: check their technical compatibility and that they are secured.

Read the full explanation
  • The mechanical, pneumatic and electrical components between the towing vehicle and trailer must be compatible. You must check that each connection is correctly coupled and secured; being able to physically join two parts is not enough to prove their technical compatibility. [RGV, art. 13.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Before starting or resuming your journey, check that the main coupling is closed, locked and secured as specified for the model. Then check its connections and auxiliary devices. If you have any doubts about the locking mechanism, you must resolve them before moving the combination. [RGV, art. 13.3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Allow the connections enough movement for the combination to articulate, while preventing them from dragging, becoming trapped or being pulled excessively tight. Functional slack does not mean they should be left unsecured. Also check that the semi-trailer’s landing legs are retracted and secured before moving off.
  • Before detaching the towed vehicle, you must secure it against movement and, if it is a semi-trailer, leave it properly supported on its landing legs. The parking brake prevents movement and the landing legs support the semi-trailer; the full procedure is covered in «Safe coupling and uncoupling». [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).

5Position lights and number plate lighting

A light truck towing a trailer travels at night in the right lane, with the trailer’s two red rear position lights switched on and a white lamp illuminating its rear registration plate.
The key idea

Check your towed vehicle’s position lights and number plate lighting.

1.60 mFront position light threshold
Non-agricultural towed vehicle lightingColourEquipment
Rear positionRedTwo compulsory lights
Front positionWhiteTwo: compulsory above 1.60 m wide; optional at or below this width
Rear number plateWhiteCompulsory lighting

Remember

  • Use position lights at night, in poor visibility, tunnels and underpasses.
  • Check that the rear number plate is lit.
  • Keep lights and number plates clean and visible.

Exam trap: Wrong: front position lights are compulsory at exactly 1.60 m. Right: they are compulsory above that width.

Read the full explanation
  • Your non-agricultural trailer or semi-trailer must have two red rear position lights. You must check that they are visible from behind and indicate the vehicle’s presence and outline. It is not enough for the lorry’s lights to be visible if the towed body obscures them. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The towed vehicle’s front position lights are two white lights; they are compulsory when its width exceeds 1.60 m and optional when it is equal to or less than this. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The towed vehicle must have white lighting for the rear number plate. You must check that it allows the plate to be identified without being obscured by mud, open doors, brackets or accessories. The number plate and the light that illuminates it are separate components, and both must retain their function. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • When you drive at night, in significantly reduced visibility or through tunnels and underpasses, you must keep the combination’s relevant position lights on. The rear number plate must be illuminated in the circumstances required by the regulations; the towing vehicle’s daytime running lights alone do not prove that all this lighting is on. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99). [RGC, art. 103](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a103).

6Brake lights, direction indicators and hazard warning lights

A person watches from the pavement as both amber hazard lights illuminate on a trailer attached to a light truck, parked beside the kerb with a wheel chocked.
The key idea

Check your towed vehicle’s brake lights, indicators and hazard warning lights separately.

Non-agricultural trailer lightsColourPurpose
Brake lightsRedTwo lights warn of braking
Rear indicatorsAmberAn even number signals direction
Hazard warning lightsAmberUse the same indicators

Remember

  • Check both sides of the trailer and the lorry too.
  • Keep the combination stationary while checking lights.
  • Keep everyone away from gaps between units and places where vehicles could hit them.

Exam trap: Wrong: red position lights prove the brake lights work. Right: apply the brake and check.

Read the full explanation
  • Your non-agricultural trailer must have amber rear direction indicators, fitted in an even number. You must check both sides: a fault on one side can leave you unable to signal precisely the manoeuvre you need to make when joining traffic or changing course. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The hazard warning signal uses the direction indicators, with the same colour and arrangement. You must check that it works on both the towed vehicle and the towing vehicle; activating the hazard warning switch does not prove that the lamps at the rear end receive power. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The towed vehicle has two red brake lights according to the general table in Annex X. You must check their response when you apply the brake, distinguishing them from the position lights: they share the same colour but warn of different situations, and you cannot consider one function checked by looking only at the other. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • For a practical check, use a person observing from a safe location or a method that allows you to verify each function properly. Do not position anyone between the vehicles or behind a combination that could move. You must carry out the check with the vehicle immobilised and the controls operated in a controlled manner.

7End-outline marker lamps: recognising width

A light truck towing a wide trailer travels in the right lane at dusk with the two red clearance lights illuminated at the upper rear corners of the trailer.
The key idea

You need end-outline marker lamps when your towed vehicle exceeds the specified width.

2.10 mCompulsory above this width
Trailer end-outline marker lampsColourNumber
FrontWhiteTwo lights
RearRedTwo lights

Remember

  • Check the lights high up too.
  • Use marker lamps with position lights at night and in significantly reduced visibility.
  • Use them in tunnels, underpasses and sections signed as tunnels, including during daylight.

Exam trap: Wrong: marker lamps are compulsory at exactly 2.10 m. Right: the width must exceed this.

Read the full explanation
  • If your trailer or semi-trailer is wider than 2.10 m, it must have end-outline marker lamps. You must associate these with width, rather than mass or the need for C1+E. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • End-outline marker lamps are white at the front and red at the rear, with two front lamps and two rear lamps in the equipment specified for trailers. Their position lets others identify the vehicle's upper edges. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must switch on the required end-outline marker lamps together with the position lights between sunset and sunrise, when visibility is significantly reduced, and when travelling through tunnels, underpasses or stretches signposted as tunnels. This obligation also applies when you travel through them during the day. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99).
  • During your exterior check, look at the high points of the towed vehicle and check that no lamps are missing, obscured or damaged. On a tall box body, checking only the lower light clusters leaves unchecked the very devices that help others judge its size.

8Side marking on the trailer

A light truck travels to the right along a road towing a long trailer with illuminated amber side marker lights and rectangular amber reflectors.
The key idea

Distinguish your towed vehicle’s side lights from its side reflectors.

6 mSide lights: length exceeded
Non-agricultural towed vehicle equipmentWhen compulsory
Side position lightsWhen longer than 6 m
Non-triangular side reflectorsWithout that length threshold

Remember

  • Check the towed vehicle’s length, rather than the whole combination.
  • Check both sides and keep devices uncovered.
  • Remember that side lights are generally amber.
  • Some rear side lights combined with rear devices may be red.

Exam trap: Wrong: side reflectors are required only above 6 m. Right: that threshold applies to side position lights.

Read the full explanation
  • Side position lights are compulsory on non-agricultural trailers and semi-trailers longer than 6 m. You must check the length of the towed vehicle when applying this condition. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • They are amber, and their number depends on the length of the towed vehicle under the installation requirements. These powered lights show the presence of the towed vehicle from the side, especially when you cross another road user's path or manoeuvre in poor lighting. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx). The table permits red for certain rear side lamps grouped, combined or reciprocally incorporated with rear devices; this exception does not make red the general colour for the side. [RGV, Annex X, notes to the trailer table](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Non-triangular side reflectors are compulsory on non-agricultural trailers, and article 16.5 does not make them subject to the 6 m threshold. You must avoid applying the length requirement for side lights to all reflective devices on the side. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • As a checking routine, walk along both sides: a check from behind can miss side lights and reflectors. Make sure toolboxes, tarpaulins, dirt or repairs do not obscure them. Checking both sides lets you spot differences in condition or devices hidden by accessories.

9Rear fog lamps and reversing lamps

A light truck towing a trailer travels in the right lane in dense fog with the trailer’s red rear fog lamp illuminated.
The key idea

Use your rear fog lamp only in particularly poor weather or environmental conditions.

6 mReversing light length threshold
Trailer length (O2, O3 and O4 trailers approved under UN Regulation 48)Compulsory white lightsAdditional optional lights
Up to 6 m longOneOne
Over 6 m longTwoTwo

Remember

  • Check your red rear fog lamps: you must have one or two.
  • Use them in thick fog, very heavy rain or heavy snow.
  • You may also use them in dense clouds of dust or smoke.
  • Keep the reversing lights required by your vehicle’s approval.
  • Check mirrors and blind spots before reversing, even with working lights.

Exam trap: Wrong: reversing lights are always optional. Right: they are compulsory on O2, O3 and O4 trailers approved under UN Regulation 48.

Read the full explanation
  • Your non-agricultural trailer must have a red rear fog lamp; the table in Annex X specifies one or two. You must check this function specifically, because working position lights or brake lights do not establish that the fog lamp is present and working. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must only switch on the rear fog lamp in particularly unfavourable weather or environmental conditions, such as thick fog, very heavy rain, heavy snowfall or dense clouds of dust or smoke. [RGC, art. 106.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • The equipment also depends on type approval: Annex X lists one or two white reversing lamps as optional, but UN Regulation 48 requires this function on O2, O3 and O4 trailers type-approved under it. For these vehicles, it specifies one compulsory lamp and a second optional lamp up to 6 m in length, and two compulsory lamps with two additional optional lamps when they exceed 6 m. Keep the lamps required for your particular vehicle. [RGV, arts. 15 and 20 and Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx). [UN Regulation 48, paragraphs 6.4.1 and 6.4.2](https://www.boe.es/buscar/doc.php?id=DOUE-L-2021-81325).
  • If your combination has reversing lamps, you must check that they indicate this manoeuvre and cannot be confused with a red braking signal. Switching them on helps warn others of the movement, but does not show that the area is clear or replace observation through your mirrors and checks of your blind spots. [RGC, art. 109.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).

10Reflectors: shape and colour

A light truck towing a trailer travels in the right lane, showing two red triangular reflectors on the rear of the trailer and yellow rectangular reflectors along its side.
The key idea

Recognise your towed vehicle’s reflectors by their shape, colour and position.

Towed vehicle reflectorsColourShape
Rear: twoRedTriangular
Front: twoWhiteNon-triangular
SideAmber, with an exception when grouped with rear signalling devicesNon-triangular

Remember

  • Keep reflectors clean and intact.
  • Remember that they reflect light and produce none themselves.
  • Do not replace lights with reflectors.
  • Do not confuse reflective number plates with reflectors.

Exam trap: Wrong: any red rear reflector will do. Right: your towed vehicle’s rear reflectors must be triangular.

Read the full explanation
  • Your trailer or semi-trailer must carry two red triangular rear reflectors. Their shape identifies it as a towed vehicle when light from another vehicle shines on them; you must keep them intact and in the prescribed shape. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Your towed vehicle has two white, non-triangular front reflectors. They reflect the light that falls on them and work without power from the lighting circuit. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Side reflectors are non-triangular and amber, with the colour exception specified for those grouped with rear signalling devices. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • A reflector does not produce the light that makes it visible. You must therefore keep it clean and intact even when the entire electrical system works. Likewise, reflectors do not replace compulsory lights or allow you to drive with an unresolved connection fault. Number plates and other regulation retroreflective plates are not considered reflectors for these purposes. [RGV, Annex X, paragraph 1.16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).

11Checking lighting and visibility

A person wearing a reflective vest checks the symmetrical red rear lights and reflectors of a trailer coupled to a light truck parked in a paved area.
The key idea

Check each lighting function before your journey.

Remember

  • Check that paired lights match in colour and brightness.
  • Keep windows, mirrors, lights and reflectors clean.
  • Resolve signalling faults before setting off.
  • If an unrepairable fault reduces lighting during your journey, slow down.
  • You must be able to stop within the lit area.

Exam trap: Wrong: any lighting fault lets you continue slowly. Right: assess the fault and arrange repair or assistance.

Read the full explanation
  • Paired devices serving the same purpose must match in colour and intensity and be positioned symmetrically as prescribed by the regulations. You must avoid improvised repairs that change the colour or leave a signal difficult to interpret; a lamp that emits light does not necessarily fulfil its regulatory function. [RGV, art. 15.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15).
  • Check the position lights, number plate lighting, indicators on each side, hazard warning lights, brake lights, end-outline marker lamps and side position lights in turn, where applicable, as well as the other functions fitted. An orderly check prevents you from mistaking an illuminated light cluster for verification of all the functions it incorporates.
  • Keep windows, mirrors, lights and reflectors clean so you can see and be seen. Interior cab lighting does not replace exterior lighting. As a safety guideline, if you detect a fault that prevents you from correctly signalling the combination's presence or manoeuvres, resolve it before starting your journey.
  • If a fault that cannot be repaired en route forces you to drive with reduced lighting intensity, you must reduce your speed until you can stop within the illuminated area. This rule does not turn every loss of trailer signalling into permission to continue: assess the fault and arrange the necessary repair or assistance. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107).

12Two number plates at the rear

Rear view of a light truck towing a trailer on the right side of the road, with a blank red plate centred on the trailer’s rear and a blank white plate to its right.
The key idea

Above the specified MMA, your towed vehicle needs both number plates at the rear.

750 kgBoth plates above this MMA
Rear plates: towed vehicle above 750 kg MMABackground and charactersPosition
Towed vehicle’s own plateRed background, black charactersCentred, vertical or nearly vertical
Towing lorry’s registrationWhite background, black charactersRight-hand side

Remember

  • If you change lorries, update the plate showing the towing vehicle’s registration.
  • Check both plates are secure, clean and visible.

Exam trap: Wrong: one rear plate is enough above 750 kg MMA. Right: you need both plates.

Read the full explanation
  • If your trailer or semi-trailer has an MMA (maximum authorised mass) exceeding 750 kg, it must carry its own number plate at the rear and another showing the towing vehicle's registration number. On your C1+E combination, you must recognise both identifiers: one belongs to the towed vehicle and the other to the towing vehicle pulling it. [RGV, Annex XVIII, paragraph III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • Its own number plate must be vertical or nearly vertical and in the towed vehicle's median longitudinal plane. The plate reproducing the towing vehicle's registration number is placed on the right-hand side. You must pay attention to the location and avoid answering that any arrangement is sufficient as long as there are two plates. [RGV, Annex XVIII, paragraph III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • On the trailer or semi-trailer's own standard number plate, the retroreflective background is red and the characters are black; its registration includes the letter R, four digits and three letters. The standard plate reproducing the lorry's registration number has a white background and black characters. These plates identify the units making up the combination. [RGV, Annex XVIII, I.A](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • If you change the towing vehicle pulling the same towed vehicle, check the plate reproducing the towing vehicle's registration number: it must match the one forming the combination. As part of your checking routine, also check that the plates are secure and clean and that nothing obscures the characters before you set off. [RGV, Annex XVIII, paragraph III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).

13Long vehicle rear plate

A light truck towing a trailer travels in the right-hand lane of a road with a yellow plate bordered in red centred on the rear of the trailer.
The key idea

You must mark your combination as a long vehicle above the specified length.

12 mSign required above this length
500–1,500 mmMounting height

Remember

  • Measure the whole combination’s length.
  • Fit the V-6 at the rear, centred.
  • Where fitting is easier, use two matching plates symmetrically, close to the edges.
  • Use visible, approved plates with yellow reflective and red fluorescent material.

Exam trap: Wrong: V-6 depends only on trailer length. Right: use the whole combination’s length.

Read the full explanation
  • The V-6 sign, Long vehicle, indicates that the vehicle or combination exceeds 12 m in length. You must consider the entire combination: you may need it even if each unit separately is shorter. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6). The condition is length, not reaching a particular mass: your C1+E combination also needs this sign if it exceeds that length.
  • You must fit it at the rear, centred on the vehicle's centreline. Where this makes fitting easier, you may use two similar plates positioned symmetrically on either side of the centreline and as close to the edges as possible. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • You must fit it between 500 and 1,500 mm above the ground. The sign has yellow reflective and red fluorescent material and must be type-approved. Its surface must remain visible from behind, with the mounting and orientation specified for the approved plate. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • Distinguish the V-6 from registration plates, the trailer's reflective triangles and the warning panel for a projecting load. Each item has its own purpose and requirement; carrying one does not exempt you from the others that apply. Marking projecting loads is covered in «Safe, well-distributed loads», in the sections «V-20 panel for loads projecting at the rear» and «Lights and reflectors for projecting loads».

14Reflective contour marking

A light truck towing a trailer travels in the right lane, showing orange reflective strips outlining the trailer’s entire rear and part of its side, together with rear lights and red triangular reflectors.
The key idea

Keep the reflective markings required by each unit’s vehicle approval.

3,500 kgO3: MMA above this
2.10 mRear contour: width exceeded
6 mSide contour: length exceeded
Unit or caseContour marking rule
C1 lorry up to 7,500 kgBelow the compulsory mass threshold for N2 vehicles over 7.5 t
O3 trailer under UN Regulation 48Full rear contour above 2.10 m wide; partial side contour above 6 m, including drawbar
Exceptions and alternativesDepend on configuration, incomplete vehicle status and approval

Remember

  • Inspect the strips from different angles.
  • Keep approved reflective material clean and undamaged.
  • Check that repairs and tarpaulins do not cover the strips.
  • Remember that V-23 markings support lights and do not replace them.

Exam trap: Wrong: a light lorry always removes the marking requirement. Right: check the trailer’s approval too.

Read the full explanation
  • The V-23 sign, Goods vehicle marking, consists of reflective marking that makes the vehicle or combination more visible and easier to recognise. Its strips allow you to identify the vehicle's shape and size when light falls on them. [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23).
  • Your C1 lorry of up to 7,500 kg does not, on account of its mass, fall within the contour marking requirement for N2 vehicles over 7.5 t. However, an O3 trailer, over 3,500 kg, may need it: UN Regulation 48 requires full contour marking at the rear if it exceeds 2.10 m in width and partial contour marking on the sides if it exceeds 6 m in length, including the drawbar for this threshold; it provides exceptions for incomplete vehicles and alternative arrangements depending on their configuration. Apply the type-approval requirements for each unit. [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4). [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23). [UN Regulation 48, paragraph 6.21.1](https://www.boe.es/buscar/doc.php?id=DOUE-L-2021-81325).
  • The material must be approved under UNECE Regulation 104 and its installation must comply with the specified technical conditions. As the driver, you must maintain the arrangement required for the vehicle and check that repairs to bodywork or tarpaulins have not left it incomplete. [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23).
  • As a practical guideline, inspect the strips from different angles during your walk-round check. A strip covered in mud or damaged loses its effectiveness even if it remains attached to the vehicle. You must also check the lights: reflective marking helps others perceive the vehicle's size and does not replace their electrical power supply.

15Mirrors on the towing lorry

A light truck with a trailer stands in a parking area, with a main exterior mirror on each side of the cab and the driver seated on the left.
The key idea

Choose mirrors for your towing lorry and keep those required by its approval.

7,500 kgMaximum lorry MMA
2 mHeight: classes V and VI
Mirrors: C1 N2 lorry up to 7,500 kgRule
Main, class IICompulsory on both sides; interior mirror optional
Wide-angle, class IVOptional in general table unless same-side main mirror is not convex; follow approval
Close-proximity, class VOptional in general table; follow approval. Entire device and attachments must stay above 2 m at every adjustment, fully laden
Front, class VIOptional. No mirror or rim point below 2 m at any adjustment, at maximum load
Insufficient height for V or VIInstallation prohibited if its height condition cannot be met

Remember

  • On your C1 N2 lorry up to 7,500 kg, keep main mirrors both sides.
  • Do not add the trailer’s MMA when choosing your lorry’s mirrors.
  • Adjust mirrors while stationary, from your driving position.
  • Keep additional devices required by the vehicle’s approval.
  • For a category B towing vehicle, apply its own equipment requirements.

Exam trap: Wrong: the interior mirror replaces main exterior mirrors. Right: keep both compulsory main exterior mirrors.

Read the full explanation
  • Your category N2 C1 lorry with an MMA (maximum authorised mass) not exceeding 7,500 kg must have two class II main exterior mirrors, one on each side. The interior mirror is listed as optional in that row of the table. You must use the category of the towing vehicle, without adding the trailer's MMA, to determine which main mirrors it requires. [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • Class IV is the wide-angle mirror and class V is the close-proximity mirror. The RGV table treats classes IV and V as optional for N2 vehicles up to 7.5 t, except that class IV is required if the class II main mirror on the same side is not convex. On vehicles approved under UN Regulation 46, you must also retain the wide-angle mirrors on both sides and the passenger-side close-proximity mirror where their installation conditions are met. Class V mirrors must remain more than 2 m above the ground in all adjustment positions, including their adjustment points and attachments, with the vehicle fully laden; if this cannot be achieved, their installation is prohibited. [RGV, Annex III, table and notes 2 and 3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii). [UN Regulation 46, paragraph 15.2.1.1.1](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-81759).
  • The class VI front mirror lets you see the area immediately in front of the cab and is optional for your C1 N2 vehicle up to 7.5 t. If you fit one, no point of the mirror or its edges may be below 2 m in any adjustment position, with the vehicle at its technically permissible maximum load. Its installation is prohibited if the cab height prevents compliance with this condition. You must apply this requirement to the front device fitted to the lorry, regardless of the mass added by the trailer. [UN Regulation 46, paragraphs 15.2.1.1.1 and 15.2.2.7](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-81759).
  • You must adjust the mirrors with the combination stationary, after sitting correctly in the seat. Check both sides and the nearby areas, keep the glass clean and check that the mountings do not vibrate or move out of position. Poor adjustment reduces the information available to you even in daylight.
  • You must retain the indirect vision devices required by the specific type approval, as well as interpreting the general table. If you drive a combination permitted by C1+E with a category B towing vehicle, identify its technical category and apply its corresponding equipment requirements: the combination's mass does not turn it into an N2 lorry. Licence entitlement limits are covered in «C1+E licence: requirements, tests and validity». [RGV, art. 11.2 and Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).

16Extension mirrors and blind spots

A person adjusts an extension mirror on a light truck parked beside the kerb with a wider box trailer attached and a driver at the wheel.
The key idea

Adjust your mirrors for the view you need with the trailer attached.

Remember

  • Check your view with the trailer actually attached.
  • Use suitable extensions if needed to improve your view.
  • Secure extensions firmly and keep mirrors clean.
  • Remember that your view changes as the combination turns.
  • If you lose a necessary reference point, stop and check your surroundings safely.

Exam trap: Wrong: someone disappears from your mirror, so the danger has passed. Right: they may be in a blind spot.

Read the full explanation
  • If the towed vehicle obstructs the necessary field of view, you must use a suitable indirect vision arrangement that complies with the vehicle's technical requirements. Extension or supplementary mirrors can provide the necessary view; you must not fit them on the basis of an automatic rule based solely on towing a trailer. [RGV, art. 11.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11). [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • As an adjustment guideline, check the field of view with the trailer actually coupled. An adjustment that works when driving the towing vehicle alone may be insufficient with a wider body or one in a different position. Secure the extensions so that they retain their orientation and do not create dangerous projections.
  • Mirrors help you monitor the sides, the towed vehicle and the nearby space, but you must know which areas they do not show. Each mirror's field of view depends on the angle between the units. A road user outside the image may be in a blind spot within the danger area.
  • If you lose a reference point needed for manoeuvring, stop and check your surroundings safely. You must keep observing throughout the manoeuvre, with mirrors that are clean, securely mounted and adjusted for the vehicle you are towing.

17Wheel chocks on a significant gradient

A light truck towing a trailer is parked uphill beside the right-hand kerb, with orange wheel chocks against the downhill side of one truck wheel and one trailer wheel.
The key idea

When leaving your seat on significant gradients, use chocks or a suitable kerb.

One chock per vehicleWhen ADR equipment is required
Combination wheel chock equipmentWhat you must carry
General compulsory equipmentDoes not include chocks; you need them when leaving your seat with the combination stopped or parked on a significant gradient without a suitable kerb
Dangerous goods, when ADR equipment is requiredAt least one chock per vehicle: lorry and trailer or semi-trailer

Remember

  • If ADR equipment is required, carry at least one chock per vehicle.
  • When leaving your seat on significant gradients without a suitable kerb, use chocks.
  • Rest a steered wheel against the kerb if you use one.
  • Use purpose-made wheel chocks; never use stones or improvised objects.
  • Choose chocks for wheel diameter and mass; store them securely and accessibly.

Exam trap: Wrong: the brake is enough when leaving your seat on a significant gradient. Right: also secure your combination with chocks or a steered wheel against a suitable kerb.

Read the full explanation
  • The combination's general compulsory equipment does not include wheel chocks, but you need them if you leave the driving seat with the combination stopped or parked on a significant gradient without a suitable kerb against which to rest a steered wheel. You must use chocks specifically manufactured to immobilise wheels; stones and other improvised objects do not meet this requirement. [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii) [RGC, art. 92.3.d](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).
  • When preparing your equipment, choose chocks suitable for the wheel diameter and the mass they must restrain on your C1+E combination. Store them securely and accessibly, in a holder or compartment that allows you to retrieve them without unloading goods, and check that they have no cracks or breaks that compromise their support.
  • If you carry dangerous goods and the equipment specified in ADR section 8.1.5.2 is required, you must carry at least one wheel chock per vehicle: one for the lorry and another for the trailer or semi-trailer. Their dimensions must suit each vehicle's maximum permissible gross mass and wheel diameter. [ADR, 8.1.5.2](https://boe.es/diario_boe/txt.php?id=BOE-A-2025-77).
  • To secure your combination on a significant gradient using chocks or a kerb, apply the guidance in «Manoeuvres with a light lorry and trailer», section «Securing the combination when leaving the driving seat». [RGC, art. 92.3.d](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).

18Parking brake and supports

An operator applies the parking brake of a trailer still coupled to a light truck, with wheel chocks in place and the front support resting on the pavement.
The key idea

Secure your towed vehicle before uncoupling and check that it stays stable.

Transmission when leaving your driving positionWhat you select
Manual, facing uphillFirst gear
Manual, facing downhillReverse gear
Transmission with parking positionParking position

Remember

  • When leaving your seat, stop the engine, switch off ignition and apply parking brake.
  • If you move away from the vehicle, take precautions to prevent unauthorised use.
  • Apply the towed vehicle’s parking brake before uncoupling.
  • Check that supports are stable and keep people clear.
  • Before driving, check coupling, connections and raised supports; remove chocks once secured.

Exam trap: Wrong: supports replace the brake. Right: they hold up the semi-trailer but do not prevent rolling.

Read the full explanation
  • When you leave the driving seat, you must stop the engine, switch off the ignition and leave the parking brake applied. If you move away from the vehicle, you must take precautions to prevent unauthorised use. With a manual gearbox, you must leave first gear engaged uphill and reverse gear downhill; with the corresponding system, select the parking position. [RGC, art. 92.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).
  • The trailer or semi-trailer's parking brake keeps it stationary even when uncoupled. You must ensure that it is applied before the towed vehicle ceases to depend on the towing vehicle. Do not confuse how the brakes work while driving with immobilising the towed vehicle once it is detached. [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • The semi-trailer's supports hold up its front end when required, but do not replace the brake or the necessary measures to prevent movement. As a safety guideline, check the stability of the support before withdrawing the towing vehicle and keep people clear of areas where the semi-trailer could fall or move.
  • Before driving again, check that the coupling is secure, check the connections and ensure that the supports are retracted and secured; remove the chocks once the combination is secured.

19Rear underrun protection

A light truck towing a trailer travels in the right lane of a rural road, with the trailer’s rear underrun protection bar straight and secured by two intact mountings.
The key idea

Keep the rear protection required by your vehicle’s category and documents.

550 mmMaximum height: O2 solution
100 mmMaximum inset on each side
Vehicle or caseRear protection
N2 lorry and O3 trailerDimensions and strength under their technical regulations
Permitted O2 trailer solutionUnladen rear height up to 550 mm; width within 100 mm of each rear axle side
Protection incompatible with vehicle useExemption must appear in vehicle documents

Remember

  • Check the rear structure and its anchor points.
  • A dedicated bar or a strong rear structure may provide protection.
  • Put movable devices in their driving position.
  • Do not apply the tractor unit’s exemption to an ordinary semi-trailer.

Exam trap: Wrong: 550 mm is the universal height for every bar. Right: it belongs to a permitted solution for O2 trailers.

Read the full explanation
  • Vehicles, including trailers and semi-trailers, must provide effective rear protection against other vehicles running underneath them. This can be achieved by a dedicated device or by the shape and strength of their rear structure. You must keep the structure and its mountings in a condition that allows them to perform this function. [RGV, art. 11.16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11). [RGV, Annex IV](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniv).
  • For an N2 lorry and an O3 trailer, you must apply the requirements for dimensions and resistance to deformation in their technical regulations. For O2 trailers, Annex IV allows, among the specified solutions, a rear structure whose unladen height does not exceed 550 mm and whose width extends to within 100 mm of each end of the rear axle. You must not treat this O2 solution as a universal bar height for all C1+E trailers. [RGV, Annex IV, sections 2.1 and 2.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniv).
  • Annex IV provides exemptions, including tractor units for semi-trailers and certain trailers for unprocessed timber or very long items. It also covers vehicles whose use is incompatible with this protection, a circumstance that must be recorded in their documentation. You must not extend the tractor unit exemption to an ordinary semi-trailer. [RGV, Annex IV](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniv).
  • As a checking guideline, make sure the bar or structure is not deformed or detached and has no damaged mountings. If a device can be moved for work purposes, follow the instructions to return it to its position for driving.

20Side and front protection

A driver inspects the side guards of a parked light truck with a trailer, with the truck’s front underrun guard also visible and highlighted in green.
The key idea

Keep the guards required by your combination’s approval and documents.

Protection where requiredWhere it works
SideAlong the sides, preventing people going underneath
FrontAt the front of the powered unit, preventing underrun

Remember

  • Check the condition and fastenings of guards.
  • Do not remove side protection to gain space.
  • Do not assume that a toolbox replaces a guard.
  • Report missing, damaged or wrongly positioned parts for correction.

Exam trap: Wrong: looking at a guard proves its strength. Right: you must meet the technical requirements.

Read the full explanation
  • Goods vehicles, including trailers and semi-trailers, must have side protection where their technical regulations require it. You must maintain the side guards with their mountings and arrangement as prescribed by the regulations. [RGV, art. 11.17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).
  • Side protection helps prevent a road user from ending up underneath the vehicle in a side collision. As a safety guideline, check its continuity, condition and attachment. You must not remove it to gain space or assume that a toolbox fitted to the side is, on its own, a substitute for regulation-compliant protection.
  • Goods vehicles must also have front underrun protection where the applicable regulations require it. You must associate it with the front of the powered vehicle, distinguishing it from the rear protection of the towed vehicle and the side guards. [RGV, art. 11.18](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).
  • To know exactly which equipment you must maintain on your combination, you must refer to its type approval, configuration and technical documentation. Your inspection as a driver consists of detecting missing, damaged or incorrectly positioned equipment and reporting it for rectification; a visual assessment does not replace the strength requirements.

21Connected V-16 and compulsory equipment

A light truck towing a trailer is stopped on the right shoulder with an illuminated yellow beacon on the highest part of its roof and its hazard lights on.
The key idea

Carry a valid connected V-16 in your non-special combination registered in Spain.

Remember

  • Check the make and model on the DGT’s official list.
  • Check the connectivity service expiry date.
  • Keep it accessible from the cab and maintain its power supply.
  • Position it as high as possible for maximum visibility.

Exam trap: Wrong: triangles or unconnected beacons are enough. Right: your non-special combination registered in Spain needs the regulatory connected V-16.

Read the full explanation
  • You must carry a valid connected V-16 in your non-special vehicle combination registered in Spain. The required equipment for advance hazard warning is the connected beacon; triangles and beacons without connectivity do not fulfil this regulatory function. Store this portable equipment where you can reach it when you need to warn others that your vehicle is immobilised. [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii). [DGT, V-16 devices](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).
  • The V-16 emits amber light and must provide maximum visibility when placed as high as possible on the immobilised vehicle. The portable warning device and the lorry's hazard warning lights perform complementary functions. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The make and model must appear on the official list of certified devices published by the DGT. Check that specific identification when choosing your beacon. Also check the expiry date of the connectivity service marked on the device. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • Store the beacon somewhere accessible from the cab and maintain its power supply according to the instructions. You must be able to use it when your vehicle becomes immobilised, without having to search among the load or walk along the arcén (hard shoulder) to a distant compartment. [DGT, V-16 devices](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).

22What the beacon must do

A light truck towing a trailer is stopped on the right shoulder of a road, with an amber beacon illuminated on the cab roof.
The key idea

Your beacon makes the vehicle visible and sends its location.

360 degreesHorizontal light coverage
30 minutesMinimum light intensity duration
100 secondsLocation update interval
12 yearsMinimum included communications

Remember

  • Keep your V-16 on while the hazard requiring a warning remains.
  • It sends activation, deactivation and location information.
  • Communication ends after it sends deactivation.
  • You do not need an external app for it to work.
  • Request assistance separately when needed.

Exam trap: Wrong: the beacon automatically requests all assistance. Right: distinguish its messages from calls you need to make.

Read the full explanation
  • The V-16 has a horizontal light coverage of 360 degrees and must maintain its prescribed light intensity for at least 30 minutes. You must keep it activated for as long as the hazardous situation requiring a warning continues. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The beacon communicates its activation, deactivation and location to the national access point for traffic and mobility. Location information is sent every 100 seconds and stops after deactivation has been communicated. You must distinguish this communication from any call you may need to make to request assistance. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The cost of communications must be included in the price and guaranteed for at least 12 years. The operating and communication components must be inside the casing, without depending on an external mobile app. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The V-16 is intended to make the vehicle involved in an accident visible and transmit its location, without additional functions. You must keep the other equipment available: the beacon does not immobilise the combination, extinguish a fire or make it safe to step out into an area used by traffic. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).

23Positioning the V-16 on a lorry

A driver wearing a seat belt places an illuminated V-16 beacon on an accessible exterior door bracket of a truck with a trailer stopped on the shoulder.
The key idea

Use your V-16 to warn of an immobilised vehicle without exposing yourself to traffic.

SituationWhat you do
You cannot safely reach the roofUse the driver’s door or an accessible side area
Body higher than cabUse the rear if you can leave safely; otherwise the highest accessible cab exterior
You cannot continue; a safe place exists outside the road platformLeave away from traffic; never remain in or walk along lanes or hard shoulders
You cannot leave safelyStay inside with your seat belt fastened

Remember

  • If breakdown or accident immobilises you, use your regulatory V-16 and hazard warning lights.
  • Use position lights and end-outline marker lamps when required, including on the trailer.
  • On carriageway or hard shoulder, use position lights at night.
  • Also use them there in significantly reduced visibility.
  • In those conditions, also use end-outline marker lamps where required.
  • Prepare an accessible, visible place to attach your beacon.

Exam trap: Wrong: you must climb onto the roof despite danger. Right: use the highest accessible, visible area safely.

Read the full explanation
  • You must place the V-16 as high as possible and where it is most visible, without exposing yourself to danger to reach the cab roof. Where the height prevents access to that area, the DGT allows you to attach it to the driver's door or an accessible part of the vehicle's side. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16). [DGT, positioning on heavy vehicles](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).
  • As practical preparation, with the vehicle parked, check where you can attach your beacon model and how you can reach that point from a safe position. With a long combination, you must also consider whether the body or load could obscure the light from certain directions, without improvising a dangerous climb. On a vehicle whose body extends above the cab, the DGT provides for positioning it at the rear if you can leave the vehicle safely; if you cannot, use the highest accessible exterior area of the cab. [DGT, positioning the V-16 on heavy vehicles](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).
  • If a breakdown or accident immobilises the combination, you must use the regulatory V-16 and switch on the hazard warning lights, as well as the position lights and end-outline marker lamps where required. Between sunset and sunrise, or when visibility is significantly reduced, you must keep the position lights and, where applicable, end-outline marker lamps on when immobilised on the carriageway or hard shoulder. You must also check these functions on the towed vehicle. [RGC, art. 130.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130). [RGC, art. 105.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a105).
  • If you cannot resume driving and there is a safe place beyond the carriageway and hard shoulder, you must leave the vehicle on the side away from traffic, without remaining in or walking along lanes or hard shoulders. If you cannot get out safely, you must remain inside with your seat belt fastened; the full procedure is covered in «Dealing with accidents and breakdowns». [RGC, art. 130.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130).

24High-visibility vest

A driver wearing a high visibility vest stands on the dirt verge beside a light truck with a trailer stopped on the shoulder of an interurban road.
The key idea

Wear your vest when leaving your vehicle onto an interurban road’s carriageway or hard shoulder.

Class 2Minimum vest class

Remember

  • Carry at least one certified high-visibility vest.
  • Check CE marking and compliance with UNE EN 471.
  • Keep it accessible in your cab to put on before getting out.
  • Keep its strips and fabric in good condition.
  • Wear it even when checking a light in these conditions.

Exam trap: Wrong: wearing a vest lets you remain on the hard shoulder. Right: avoid traffic exposure and seek safety.

Read the full explanation
  • You must carry at least one high-visibility reflective vest as part of the equipment for your non-special vehicle combination. Annex XII requires CE marking and compliance with UNE EN 471, at least class 2 for both the area of the materials and retroreflection. You must check its certification as personal protective equipment: a light-coloured garment or one with a decorative strip does not demonstrate compliance with these requirements. [RGV, Annex XII, sections 1.b and 2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • As the driver of a goods vehicle or a non-agricultural vehicle combination, you must wear it if you leave the vehicle and are on the carriageway or hard shoulder of an interurban road. You must associate the duty to wear it with that situation, even if you get out to check a light rather than deal with an accident. [RGC, art. 118.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a118).
  • As a preparation guideline, keep the vest accessible in the cab so you can put it on before getting out. Keep its strips and fabric in good condition. Storing it in a compartment you can only reach by walking along the hard shoulder makes it harder to obtain the very protection you need when leaving the vehicle.
  • The vest makes you more visible, but you must still avoid exposure to traffic. It does not authorise you to remain beside the trailer on the hard shoulder or cross lanes to check its lighting. You must also apply the rules for leaving the vehicle and remaining in a safe place in the event of a breakdown. [RGC, art. 130.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130).

25Fire extinguishers for a goods vehicle combination

A driver checks a fire extinguisher secured in an open compartment of a light goods truck with a goods trailer parked beside the kerb.
The key idea

Choose your extinguisher using the combination’s MMA, even when driving empty.

7,000 kgRating changes above this MMA
21A/113BLower band rating
34A/144BUpper band rating
Goods combination MMA: general tableMinimum equipment
From 3,500 to 7,000 kgOne 21A/113B extinguisher
Above 7,000 and up to 20,000 kgOne 34A/144B extinguisher
C1+E scopeCombination MMA no more than 12,000 kg

Remember

  • Carry suitable, approved equipment in working order.
  • You need it for ordinary goods too.
  • Do not confuse the rating with the extinguisher’s weight.
  • Check mounting, access, condition, seal and maintenance.
  • For dangerous goods, follow their specific rules too.
  • You may use the alternative minimum ADR equipment for the relevant MMA.

Exam trap: Wrong: choose by actual load or the lorry alone. Right: use the combination’s MMA; the rating changes above 7,000 kg.

Read the full explanation
  • You must carry suitable, type-approved firefighting equipment in working order in your combination that is not classified as a special vehicle combination. This requirement does not depend on carrying dangerous goods: it also applies to ordinary goods transport. You must check this equipment before starting work. [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • For goods vehicles and combinations, the general table requires one extinguisher with a minimum fire rating of 21A/113B for an MMA (maximum authorised mass) from 3,500 to 7,000 kg; above 7,000 kg and up to 20,000 kg, it requires one rated 34A/144B. Within your C1+E entitlement, you must apply the band corresponding to the combination’s MMA, which must not exceed 12,000 kg; driving unladen does not reduce the equipment required. [Order of 27 July 1999, second provision](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#segundo). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • With a combination with an MMA of 7,000 kg, you need one extinguisher rated 21A/113B; with one of 8,000 kg or 12,000 kg, you need one rated 34A/144B. The band changes when you exceed 7,000 kg, even if the lorry on its own falls within a lower band. You must read the certified fire rating: the letters and figures do not indicate the mass of the extinguisher, and you cannot replace them with a figure in kilograms. [Order of 27 July 1999, second provision](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#segundo).
  • As an alternative, the Order allows the minimum equipment required under ADR for the relevant MMA. If you carry dangerous goods, you must also comply with the specific regulations for them. You must determine whether your transport operation falls under this specific regime before choosing the equipment. [Order of 27 July 1999, second provision](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#segundo).
  • You must carry portable, manually operated extinguishers with an extinguishing agent suitable for the vehicle, preferably dry powder or another suitable agent. You must have them checked regularly and ensure they undergo the minimum maintenance operations required by the Order. As a practical check, inspect their mountings, accessibility, condition, seals and service indicators, and replace any faulty extinguisher or report any defect. [Order of 27 July 1999, first provision](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#primero).

Check the towed vehicle’s signalling equipment

Check each function with the combination immobilised and the connections secure.

  1. Check the electrical connection and inspect the condition of the lights, reflectors, plates and contour marking strips.
  2. Switch on the position lights and also check the number plate lights, end-outline marker lamps and side position lights where applicable.
  3. Operate each direction indicator and then the hazard warning lights; check the rear end of the combination.
  4. Check the brake lights, rear fog lamp and any reversing lights fitted, with assistance provided safely.
  5. Rectify faults and remove anything that obscures the signalling equipment before driving.

Secure the combination on a slope

Apply the measures in article 92.3 and check that the combination is immobilised.

  1. Immobilise the combination and apply the parking brake.
  2. When leaving the driving seat, stop the engine, disable the starting system and select first gear facing uphill, reverse facing downhill or park, depending on the transmission.
  3. On a significant slope, use suitable wheel chocks or rest a steered wheel against a kerb as required by the regulations.
  4. If you use a kerb, turn the wheels towards the centre of the road facing uphill and outwards facing downhill.
  5. Check that the combination is secure; when moving off again, remove the chocks from the road and stow them.

Use the V-16 from the cab

Warn others that you are immobilised while avoiding exposure to traffic.

  1. Immobilise the combination and use the hazard warning lights and any other appropriate lights.
  2. Take the connected V-16 from its accessible storage location and activate it according to its instructions.
  3. Place it as high as possible for maximum visibility; if the lorry’s height prevents access to the roof, use a suitable accessible point on the side.
  4. Put on your high-visibility vest before getting out if you are going to enter the carriageway or arcén (hard shoulder) on an interurban road.
  5. Only get out if there is a safe place beyond the carriageway and hard shoulder; otherwise remain inside with your seat belt fastened.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1A lorry tows a non-agricultural semi-trailer that is 7 metres long. Must that semi-trailer be equipped with side position lights?
2Before setting off with a semi-trailer, you must check that:
3A trailer has safety chains forming a secondary coupling beside the main coupling. What do they do if the main coupling separates?
4Before leaving with a C+E combination, an essential check is that the combination's connections:

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module