Theory · D1+E Licence - Minibus with Trailer · Module 7 of 13

Safe loads and luggage

You learn to distribute and secure luggage in the minibus and its trailer, maintaining stability and respecting each unit's capacities. You study lashings, moving loads, liquids, covers, and loading and unloading operations.

38 min read22 sectionsReviewed Nov 3, 2026
A worker checks luggage straps in the trailer of a minibus parked beside the kerb, with suitcases also secured in its luggage compartment.
Luggage distributed and secured throughout the combination

1Secure loads throughout the combination

A green minibus towing a blue trailer travels in the right lane of a road, with suitcases secured by straps in the compartments of both vehicles shown in cutaway.
The key idea

Secure the load and its accessories in both the minibus and trailer.

Remember

  • Secure items for pulling away, braking and turning.
  • Prevent the load dragging, falling off or moving dangerously.
  • Avoid unnecessary noise, dust and nuisance.
  • Keep lights, compulsory signs and your hand signals visible.
  • Keep both the trailer plate and its plate showing the minibus registration visible.
  • Do not cover the V-6 sign when it is required.

Exam trap: Wrong: securing luggage for the parked vehicle is enough. Right: secure it for pulling away, braking and turning.

Read the full explanation
  • You must prepare the minibus and its trailer as a system: suitcases, equipment and occupants alter the distribution of mass and the forces transmitted through the coupling. A properly positioned load must stay in place when you move off, brake and turn.
  • You must prevent the load and its accessories from dragging, coming loose or moving dangerously, impairing stability or causing avoidable noise, dust and nuisance. This obligation also covers chocks, tarpaulins, bars and other items used to arrange or protect the load. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • You must keep lights, number plates and compulsory markings visible, including when the doors and cover are closed. On the trailer, luggage and its accessories must not obscure its own number plate, the second plate bearing the minibus registration number, or the V-6 long vehicle sign where required. They must not obscure your hand signals either. [RGC, art. 14.1.d](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14). [RGV, Annex XVIII, III.4 and Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826).
  • The sequence of coupling checks is covered in «Coupling and uncoupling the trailer».

2Plan stowage before loading

Two people plan the placement of a box, two suitcases and a machine beside a minibus with a trailer whose floor has load-spreading plates, supports, anchor points and securing straps ready.
The key idea

Decide where to place each item and how to secure it before loading.

Remember

  • Check each item’s weight, shape and fragility.
  • Check where its weight is concentrated.
  • Check the strength of the floor, supports and lashing points.
  • Provide supports to spread the weight where needed.
  • Plan which suitcases, bicycles or sports equipment passengers collect at each stop.
  • Keep the rest secure and leave access to luggage without dismantling the group’s stowage.

Exam trap: Wrong: extra straps fix any poor placement. Right: plan load distribution and securing together.

Read the full explanation
  • You must know the mass, dimensions, shape and fragility of the items before deciding where to place them. Identify their centre of gravity too when it differs from their geometric centre, as with some sports equipment. A bulky box may weigh less than a small piece of metal. On an excursion, identify the suitcases, bicycles and boxes of equipment beforehand so that access requirements alone do not determine where you load the heaviest items.
  • You must check that the floor, supports and lashing points are suitable for these items. A concentrated load may exceed the local strength of the floor even when the total mass is permissible. Allow for load-spreading plates or supports where the design of the platform and the load itself requires them.
  • You must organise the load according to the stops where passengers collect their suitcases, bicycles or sports equipment. Plan which items you need to reach at each stop and how the others remain secured when you remove them. Leave access that allows you to retrieve luggage without unnecessarily dismantling the whole group's stowage.
  • You must choose the positioning and restraint together: where each item rests, which spaces remain empty and which devices prevent movement. Annex III requires you to consider axle load distribution and the strength of the components used for securing the load; adding straps at the end does not correct every stowage error. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).

3Keep the centre of gravity low and central

A minibus towing a trailer travels in the right-hand lane and shows rigid cases secured near the floor of its luggage compartments with lightweight bags on top.
The key idea

Place heavy items low down and balance the load between both sides.

Remember

  • Place heavy items near the floor, in the spaces provided.
  • Spread the weight between both sides.
  • When stacking, place heavy items below light ones.
  • Check that packaging can support the items above.
  • Prevent the load sliding or tipping over.

Exam trap: Wrong: strong lashings fix a high or off-centre load. Right: distribute it correctly too.

Read the full explanation
  • You must place the heaviest items close to the floor, in the designated spaces in the minibus and trailer. A high centre of gravity reduces the lateral force needed to cause an overturn: on bends and roundabouts, you can reach that threshold at a lower speed than with the same mass positioned lower down. This physical effect explains the obligation to maintain stability. [RGC, art. 14.1.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • You must balance the load between both sides. A centre of gravity displaced to one side reduces the margin against overturning towards that side, especially when it is towards the outside of a bend. Lashing prevents items from moving, but does not correct an off-centre distribution. [RGC, art. 14.1.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • When stacking, you must respect the strength of the packaging and provide a stable base for the items above. As a stowage guideline, place heavy items below lighter ones and avoid small or uneven supports. Crushed packaging can loosen the top-over lashing and allow the whole stack to move.
  • You must prevent both sliding and tipping of the load itself. Tall activity equipment can tilt even if its base does not slide across the floor; you need a system suited to its shape. Preventing longitudinal and transverse tilting is part of the load-securing principles. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).

4Distribute mass between the axles

A minibus towing a trailer with luggage secured by straps is stationary on individual weighing pads beneath the wheels of its three axles in a weighing area beside a kerb.
The key idea

Respect weight limits for the combination, each vehicle, the axles and the coupling.

Change in a centre-axle trailerPossible effect on coupling
Move items forwardsMay increase the weight it carries
Move items backwardsMay reduce weight too much or tend to lift the coupling

Remember

  • Check both maximum and minimum axle loads.
  • Use the manufacturer’s load distribution diagram when available.
  • With centre-axle trailers, check the weight carried by the coupling.
  • Respect the limits for the minibus, trailer and coupling.
  • If unsure, weigh by axle and check coupling load where applicable.
  • Recheck distribution if you change vehicles, trailers or item positions.

Exam trap: Wrong: a legal total weight guarantees every limit is met. Right: check axles and coupling too.

Read the full explanation
  • You must comply simultaneously with the authorised mass of the combination, each vehicle and each axle or axle group, together with the applicable technical limits. The total may be legal while an axle is overloaded. To select the values for your configuration, consult «Maximum dimensions and masses». [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826).
  • You must use the manufacturer's load distribution diagram where available. It shows you where the load's centre of gravity may be located according to its mass.
  • With a centre-axle trailer, you must take account of the vertical load transmitted by the drawbar to the minibus coupling. Moving items forwards may increase it; moving them backwards may reduce it excessively or create a tendency to lift the coupling. Respect the values permitted for the vehicle, trailer and coupling device, in accordance with their documentation and the loading plan; do not adopt a universal percentage.
  • You must maintain the necessary minimum axle loads as well as avoid exceeding their maximums. A distribution that unloads the steering or drive axles too much impairs control and the ability to transmit forces to the ground. Annex III requires you to consider maximums and minimums within the MMA (maximum authorised mass). [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • If you do not know the actual distribution, use suitable weighing by axle or axle group as a practical check, and also check the vertical coupling load where applicable. Weighing only the whole combination does not allow you to detect each local overload. Repeat the assessment when you change the minibus, trailer or luggage distribution.

5Split the load without creating overloads

A minibus carrying passengers is parked at the right-hand kerb with two secured suitcases in its lower compartment and more secured luggage in its trailer, while a person watches from the pavement.
The key idea

Share luggage according to available capacity, and include passenger weight.

Remember

  • Spread items between authorised spaces according to their capacities.
  • Count passengers and luggage together when checking the minibus weight.
  • Do not shift an overload onto another axle that also becomes overloaded.
  • Remove luggage or use other transport if needed.
  • Recheck distribution after luggage is collected or passengers get off.

Exam trap: Wrong: you can carry anything that fits inside. Right: check weight and every limit too.

Read the full explanation
  • If the luggage can be split into separate items, you must distribute it between the authorised spaces in the minibus and trailer according to their capacities. Splitting it does not mean assigning the same mass to each vehicle: the available space, payload and distances between supports differ. Occupied seats also use up the minibus's load capacity.
  • You must check the minibus with both passengers and luggage included; together, they must not cause it to exceed its maximum authorised mass. A full group with bulky luggage requires you to review the plan before accepting more items. [RGC, art. 9](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a9).
  • You must avoid correcting an overload by piling suitcases over another axle that also becomes overloaded. The correction must satisfy every limit; it may require you to remove luggage or use other transport. Securing the load more tightly does not increase the capacity of the floor, axles or coupling.
  • Volume and mass are different: the fact that a box fits inside the trailer does not prove that you can carry it together with all the others. Organise small items in suitable containers so that you can distribute and restrain them without dangerous gaps. If the distribution changes after luggage is collected or passengers get off, check the remaining situation.

6Forces the restraint must withstand

A minibus towing a trailer travels in the right-hand lane with its brake lights on and a crate and several suitcases secured by straps and blocks in the trailer.
The key idea

Prepare restraints to withstand braking, turning and emergencies.

0.8Forward force factor
0.5Sideways and rearward force factor
Force direction in M2 and M3 passenger vehiclesRequired strength: load weight multiplied by
Forwards0.8
To each side0.5
Backwards0.5

Remember

  • Choose restraints according to weight, grip and angles.
  • Check the risk of tipping over too.
  • No single number of straps suits every load.
  • The factors describe strength, not load you can leave loose.
  • These inspections include M2 and M3 passenger vehicles.
  • Secure loads in lighter luggage trailers too.

Exam trap: Wrong: exceeding 750 kg automatically brings a trailer within these inspections. Right: check its category.

Read the full explanation
  • You must allow for inertia making the load tend to keep moving when you brake and tend to move sideways when you change direction. Preventing it from falling off while travelling straight ahead at a constant speed is not enough: the restraint must also work during demanding manoeuvres. In your combination, a loose suitcase in the aisle and a loose box in the trailer pose different risks to people, but both need suitable positioning and restraint.
  • The system must withstand a forwards force equivalent to the weight of the load multiplied by 0.8, a force towards each side multiplied by 0.5 and a rearwards force multiplied by 0.5. You must understand these factors as strength requirements for the restraint, without interpreting them as percentages of mass that you can leave unsecured. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • You must size the system to take account of all the forces, supports and strengths involved. There is no universal number of straps suitable for every box of materials or every item of the group's equipment. Mass, friction, angles and the possibility of tipping determine which securing devices you need and how many.
  • You must maintain restraint in emergencies and when moving off uphill too. The inspection may check that changes in position are minimal and that the load cannot leave its space. [RD 563/2017, art. 11](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#a1-3).
  • You must understand the scope of these technical criteria: RD 563/2017 governs commercial vehicle inspections and includes passenger vehicles in categories M2 and M3. A trailer over 750 kg does not automatically belong to the heavy trailer categories covered by that royal decree. The general obligation to carry loads safely also applies to lighter luggage trailers. [RD 563/2017, arts. 2 and 11](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#a2). [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).

7EN standards and choosing a method

A minibus with a trailer carries an open chest containing luggage held by orange straps, with the chest secured to the trailer frame by green straps and supporting blocks.
The key idea

Choose suitable securing equipment and check the strength of its supports too.

StandardApplication
EN 12195-1Calculating lashing forces
EN 12195-2Synthetic fibre straps
EN 12195-3Chains
EN 12195-4Steel wire ropes
EN 12640Lashing points
EN 12642Vehicle body strength

Remember

  • Follow the securing plan and equipment instructions.
  • You can combine blocking, locking, direct lashing and top-over lashing.
  • Check the strength of the points you attach lashings to.
  • If you carry a storage box, secure it to the vehicle.
  • Secure the contents of the box too.

Exam trap: Wrong: a strong strap is enough with a weak support. Right: check the whole system.

Read the full explanation
  • EN 12195-1 is the standard for calculating lashing forces cited in Annex III. Parts EN 12195-2, EN 12195-3 and EN 12195-4 cover synthetic fibre straps, chains and steel wire ropes respectively. You must use equipment appropriate for the load and its intended use. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • Calculating the lashings and checking the strength of the structure that takes their forces are separate checks. The same annex cites EN 12640 for lashing points and EN 12642 for vehicle body strength. A strong strap is insufficient if you attach it to a component that cannot withstand the transmitted force. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • You can combine methods: locking, blocking, direct lashing and top-over lashing. You must choose a combination whose effectiveness you can justify for the specific load. A container lock works differently from a strap that presses a box of equipment against the floor. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • You must follow the load securing plan and the equipment instructions without assuming that different systems are equivalent. If you load a storage box or container onto the trailer, check both its attachment to the vehicle and the restraint of its contents. Closing a box does not prove that the whole box is lashed down or that its contents cannot tip it over.

8Block movement with strong supports

A minibus parked beside the kerb tows a trailer with three cases blocked by rigid supports connected to its frame and secured with straps.
The key idea

Use strong supports to stop the load moving.

Remember

  • Block movement with bars, wedges or other suitable supports.
  • Reduce dangerous gaps between items.
  • Use gap fillers that withstand the expected forces.
  • Check the strength of walls, doors and supports.
  • Secure bicycles and trolleys with suitable supports or chocks and any necessary lashings.

Exam trap: Wrong: any side curtain works as a strong wall. Right: check which forces it withstands.

Read the full explanation
  • When blocking a load, you must prevent its movement using strong components: headboards, spacers, bars, stanchions, chocks or suitable recesses. Position the load and supports so that forces pass into a structure capable of taking them, without relying on substantial movement first.
  • You must reduce gaps that are incompatible with the blocking system. Free space allows an item to gain momentum before hitting the next item or the wall. Use fillers suitable for the expected forces; a soft material used to protect surfaces does not automatically serve as a strong stop.
  • You must check which forces the headboard, walls and doors are certified to withstand. A side curtain can only help restrain the load to the extent allowed by its design and certification. Annex III requires you to take account of the strength of the components used for securing. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • For bicycles, equipment trolleys and other items that can roll, you must provide suitable supports, cradles or chocks and secure them, together with the necessary lashings. A wheel can turn even if it does not slide across the floor. Do not rely entirely on the item's parking brake or on resting it against other suitcases to restrain it.

9Use friction in a controlled way

A minibus with a trailer is parked beside the right-hand kerb and carries a wooden crate resting on green anti-slip mats and secured with two orange top-over lashings.
The key idea

Check grip between surfaces and protect the load against tipping over too.

Remember

  • Check for dust, oil, water or scraps between surfaces.
  • Place anti-slip material according to the securing plan.
  • Check its condition and place it under the load’s contact points.
  • Use a justified grip value in your calculations.
  • Review securing if the surfaces in contact change.
  • Combine grip, blocking and lashings where needed.

Exam trap: Wrong: preventing sliding prevents every overturn. Right: check whether the load can tip too.

Read the full explanation
  • When using friction, you make use of the resistance to sliding between surfaces in contact. You must assess the materials and their actual condition: dust, oil, water or packaging debris can alter grip. The weight of the load alone does not guarantee that it remains still during braking.
  • You can use suitable anti-slip material between the load and the floor or between layers, in accordance with the load securing plan. You must place it at the points of support and check its condition. You cannot assume that a damaged or poorly positioned mat, or one subjected to unsuitable pressure, provides effective restraint.
  • You must use a justifiable coefficient of friction to calculate the lashings; do not choose one based on how the surface looks. Top-over lashing uses additional pressure to increase friction. If the actual contact between materials changes, you must review the calculation and the planned solution.
  • You need separate checks for sliding and tilting. Improving friction can prevent the base from moving, but a tall or narrow load unit still needs stability against tipping. Assess both risks and combine anti-slip material with blocking or lashing where appropriate.

10Top-over lashing and direct lashing

A minibus with a trailer is parked beside the right-hand kerb and carries a crate on a pallet, secured with orange straps over the top and green direct lashings between the crate and the trailer anchors.
The key idea

Understand how each lashing works and what its equipment data means.

LashingHow you secure itMain purpose
Top-overPass it over the load and tighten itPresses down to increase grip
DirectConnect suitable load points to vehicle pointsResists movement in the intended directions

Remember

  • Follow the lashing plan and its angles.
  • For top-over lashing, consider tension and packaging strength.
  • For direct lashing, check which movements its direction prevents.
  • Read LC as lashing capacity.
  • Read STF as standard tension force.
  • Do not swap LC and STF in calculations.

Exam trap: Wrong: LC tells you how hard the tensioner presses. Right: distinguish LC capacity from STF tension.

Read the full explanation
  • For top-over lashing, you must pass the restraint over the load and tension it towards the anchor points to press the load against its supporting surface. Its main purpose is to increase friction. You need to consider the transmitted pre-tension, the angle and the strength of the packaging, as well as the number of lashings.
  • For direct lashing, you must connect suitable points on the load to points on the vehicle so that the restraints resist movement in the intended directions. Their effectiveness depends on their capacity and orientation. An arrangement that restrains forward movement may need additional restraints to prevent sideways or rearward movement.
  • You must read the equipment data: LC identifies the lashing capacity and STF the standard tension force. You cannot use these quantities interchangeably in calculations. A high lashing capacity does not mean that the tensioner applies the same force when you tighten it over a box of equipment.
  • You must keep to the angles in the lashing plan. If a top-over lashing lies at too shallow an angle, the component of force pressing the load against the floor decreases; for a direct lashing, what matters is the part of the force that opposes movement.

11Look after straps, anchor points and packaging

A person checks the anchor points and ratchet tensioners of the straps securing crates with corner protectors on the trailer of a parked minibus.
The key idea

Inspect lashings and protect both their parts and the packaging.

Remember

  • Check straps, stitching, ropes, chains, hooks and tensioners before use.
  • Set aside damaged parts or those without enough identification.
  • Follow the manufacturer’s rules for withdrawing equipment.
  • Protect straps from sharp edges.
  • Attach hooks securely to suitable points only.
  • Check connections between items and their attachment to the vehicle.

Exam trap: Wrong: suitcase handles are enough to lash luggage to the vehicle. Right: check suitable restraint.

Read the full explanation
  • You must check straps, stitching, chains, wire ropes, hooks and tensioners before using them. Set aside damaged items or those whose identification does not allow you to verify their performance, and follow the manufacturer's criteria for taking equipment out of service.
  • You must protect lashings from edges that could cut them and protect the load from pressure where necessary. Corner protectors help distribute forces, but they must be compatible with the system. A protector must remain in place during the journey to serve its purpose.
  • You must attach hooks to points designed to take the force, without resting a hook in an unstable position or forcing catches and ratchets. The strength of the restraint assembly is limited by its components and their connections; you cannot determine it solely from the strap's label.
  • Wrapping film used to group items, suitcase handles or elastic bands holding a package closed do not by themselves secure a load to the vehicle. Check both how the objects are held together and how the whole load is secured to the floor. A stack can come apart even if the bottom item remains restrained.

12Check the load during service

A driver checks the lashings securing crates in the trailer of a minibus parked in a roadside rest area.
The key idea

Check the load before leaving and whenever the journey may affect its restraint.

Remember

  • Check the minibus and trailer before moving off.
  • Check supports, gaps, tensioners, doors and covers.
  • Tidy away tools and loose strap ends.
  • Recheck lashings after the load settles and at suitable stops.
  • After heavy braking or an incident, check in a safe place.
  • If you find problems, fix the cause before continuing.

Exam trap: Wrong: simply tighten a loose tensioner. Right: inspect and correct the cause.

Read the full explanation
  • You must inspect the result before moving off: no dangerous gaps, stable supports, closed tensioners and loose strap ends stowed away. Check that there are no loose tools and that doors, tailgates and covers are secured. Your check must cover both vehicles in the combination.
  • As a safety guideline, you must check the lashings again once the load has settled and at appropriate stops during service, in accordance with the transport plan. Some loads compress or vibrate and lose pre-tension. There is no single rechecking distance suitable for all luggage and equipment.
  • You must check the restraint after heavy braking, any movement you notice or an incident that may have disturbed the stowage, stopping in a safe place. If you detect tilting, an unusual noise or a loose tensioner, you must resolve the cause before continuing; tightening without inspecting can conceal a broken support.
  • You must take a deficiency seriously even if the load remains inside. Annex III distinguishes between securing that needs improvement, inadequate securing with a risk of significant movement or tipping, and a direct danger to traffic or people. An inspection can assess tensions, calculations and certificates as well as examining the load. [RD 563/2017, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).

13Stops to collect luggage and opening the tailgate

A person tightens the restraints around the remaining suitcases in an open trailer hitched to a minibus parked beside the kerb, with an unloaded suitcase beside them.
The key idea

After unloading some luggage, check what remains before continuing.

Remember

  • Recheck distribution, gaps and blocking.
  • Replace lashings and supports removed for unloading.
  • Before opening doors, check whether the load presses against them.
  • Stand clear of where items could fall.
  • If you uncouple the trailer, check its stability throughout the operation.
  • Follow trailer instructions for ground, supports and load distribution.

Exam trap: Wrong: less luggage always means greater safety. Right: recheck the new distribution and restraint.

Read the full explanation
  • After removing luggage at a stop, you must check the mass distribution and blocking again. You may leave a gap between suitcases that previously supported one another or concentrate the remaining mass at one end. Driving with less weight does not guarantee a safer distribution.
  • You must restore any lashings and supports removed for unloading, following a plan suited to the remaining load. Also assess any items temporarily moved to gain access to others.
  • Before opening doors or releasing restraints, you must consider whether the load is resting against them or has shifted. Stand clear of the path of any falling load and follow the equipment's safe operating procedure. Do not use your body to hold back a door under pressure.
  • If you leave the trailer uncoupled for loading or unloading, as a precaution check that the ground, supports and load distribution keep it stable throughout the operation. Removing items from one end first can abruptly change its balance. Do not rely on the jockey wheel to guarantee stability with any load distribution; follow the trailer's instructions.

14Liquids in portable containers

A green minibus travels in the right-hand lane towing an orange tank trailer whose cutaway shows a partially filled water tank with a wave inside.
The key idea

Secure water containers and allow for the liquid moving inside.

Remember

  • A partly filled container can surge when you brake or turn.
  • The liquid can push repeatedly against its container.
  • Allow for changing weight distribution when checking trailer stability.
  • Use a suitable container and follow filling and closure instructions.
  • Check for leaks and secure it against rolling or tipping.
  • Follow specific rules when carrying fuel.

Exam trap: Wrong: securing the container stops the liquid moving. Right: allow for its movement and the forces it creates.

Read the full explanation
  • If you carry a partially filled water container, the liquid can move inside when you brake or turn and exert successive forces on the container, even if it remains secured. This sloshing changes the instantaneous mass distribution; you must take it into account when preparing the luggage trailer for stability. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • To carry water or fuel in a portable container, you must use one suitable for its contents, follow the manufacturer's filling and closure instructions and check for leaks. Secure the container in a suitable holder to prevent it from rolling or overturning; for fuel, you must also comply with the specific regulations that apply. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).

15Suspended loads and moving loads

A minibus tows a trailer shown in cutaway with a chest secured to the floor and a device whose articulated arm is immobilised by an internal strap and snug supports.
The key idea

Control swinging and lock moving parts before carrying equipment.

LoadMovement to control
Suspended loadSwinging that shifts weight distribution
Articulated or extending equipmentParts changing position during the journey
Equipment with drawers, lids or removable traysParts opening and striking nearby luggage

Remember

  • Do not leave heavy equipment hanging without controlling its swinging.
  • Allow for changing weight distribution when the load moves.
  • Secure the frames and wheels of suspended bicycles.
  • Check that handlebars and pedals cannot hit other items.
  • Fold and lock moving parts as instructed before securing the equipment.
  • Check transport locks on drawers, lids and removable trays.

Exam trap: Wrong: securing equipment is enough even if its drawers can open. Right: check its transport locks too.

Read the full explanation
  • You must anticipate the swinging of suspended objects: it shifts their centre of gravity and transmits forces to their supports. If a bicycle hangs from a trailer rack, use the restraints provided to control movement of the frame and wheels; also check that the handlebars and pedals do not strike other equipment or suitcases. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • Hinged or extending parts of sports equipment can change position during the journey. You must fold and lock these parts according to their instructions: for example, the handlebars of folding equipment or a sliding part of its rack. Check the transport position before securing the assembly to the trailer. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • For equipment with drawers, lids or removable trays, you must check its transport catches before loading it. A part that opens while you are driving changes the forces on the support and can strike adjacent suitcases. Use the locking devices provided by the manufacturer for that configuration. [RGC, art. 14.1.a and b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).

16Removing a container from the trailer

An operator checks the closed valve of a tank trailer attached to a minibus stopped beside the kerb, with the liquid and the space above it visible in a cutaway of the tank.
The key idea

Prepare a firm support and keep passengers clear when removing a container.

Remember

  • Identify the contents before removing the container.
  • Prepare a firm support to place it on.
  • Keep passengers away from the route while you remove it.
  • Get help if its weight or shape makes it hard to grip safely.
  • Follow specific rules when handling dangerous substances.

Exam trap: Wrong: remove any container without preparing. Right: identify its contents, prepare support and keep passengers clear.

Read the full explanation
  • As a handling guideline, identify the contents before removing a container and prepare a firm support on which to place it. Keep the passengers' route separate while you take it out of the trailer, and use handling aids if its mass or shape makes it difficult to grip safely. Carry out operations involving dangerous substances in accordance with the specific provisions that apply to them. [RGC, art. 16.d](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16).

17Choose the loading and unloading location

A worker loads a suitcase into a trailer attached to a minibus in a private courtyard separated from the road by a wall and a planted strip.
The key idea

Load and unload off the road, unless using the road is unavoidable.

LocationConditions you must follow
Off the roadYour normal loading and unloading location
On the road, exceptionallyOnly when unavoidable; without danger or serious disruption
Built-up areasAlso follow municipal times and locations

Remember

  • On the road, avoid danger or serious disruption to others.
  • Follow stopping and parking rules.
  • In built-up areas, also follow municipal times and locations.
  • Where possible, work on the side nearest the carriageway edge.
  • Provide enough equipment to work quickly without unnecessary nuisance.
  • Do not place luggage or equipment on the carriageway, hard shoulder or pedestrian areas.

Exam trap: Wrong: unload on the road for convenience. Right: only when unavoidable, without danger or serious disruption, following the rules.

Read the full explanation
  • You must load and unload off the road. You may only do so on the road when it is unavoidable, without causing danger or serious disruption to other road users. The convenience of stopping next to where passengers are waiting does not make every point on the road a suitable location. [RGC, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16).
  • If you exceptionally have to operate on the road, you must follow the stopping and parking rules. In built-up areas, you must also comply with municipal provisions on times and locations. A designated loading and unloading bay does not remove its conditions of use or authorise you to occupy any nearby space. [RGC, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16).
  • You must carry out these operations, wherever possible, on the side of the vehicle nearest the edge of the carriageway. In right-hand traffic, this is usually the right-hand side; you must take account of the actual vehicle position and the authorised location, without entering the traffic area out of habit. [RGC, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16).
  • You must have sufficient means to carry out the operation as quickly as possible and avoid unnecessary noise and disturbance. You must not place suitcases, bicycles or boxes on the carriageway, the arcén (hard shoulder) or pedestrian areas. [RGC, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16).

18Prepare the area and the operation

A minibus with a trailer secured with wheel chocks and a deployed ramp remains stationary while two people coordinate using hand signals beside a luggage trolley.
The key idea

Prepare the site and coordinate people before moving luggage.

Remember

  • Check the ground, space and ramp compatibility.
  • Keep passengers’ routes clear of the luggage handling area.
  • Secure the combination against movement using the devices provided.
  • Keep passengers clear of bicycles, ramps and tailgate trapping points.
  • Agree who guides and where to place items; stop if you lose contact.
  • Before leaving, stow equipment and check nobody is behind the trailer looking for luggage.

Exam trap: Wrong: you can move off once everyone is on the minibus. Right: confirm luggage handling has finished too.

Read the full explanation
  • Before starting, you must check that the ground is firm and level and that there is enough space to open the tailgate and remove the suitcases. If you use a ramp for bicycles or sports equipment, check its capacity, support and compatibility with the trailer. Set aside a route for passengers separate from the area where you handle the items.
  • As an operating guideline, secure the combination against movement and coordinate the start with the people loading the luggage. Use the devices provided with the equipment to prevent movement while people or loading equipment are in its working area.
  • When handing over luggage, you must keep passengers clear of the paths of bicycles and ramps and of the tailgate's trapping points. If another person helps you move bulky equipment, agree who directs the movement and where you place it; stop the operation if you lose contact with them.
  • Before moving off, you must confirm that you have removed and stowed ramps, trolleys and all other auxiliary equipment. Check that nobody remains behind the trailer or is leaning over its opening to look for a suitcase. You must coordinate the notification that the whole group has boarded the minibus with confirmation that luggage handling is complete.

19Luggage and passenger safety

A minibus with a trailer is stopped beside the kerb, with passengers seated and belted, the aisle and steps clear, and suitcases secured in the trailer while an attendant checks them from the pavement.
The key idea

Position luggage so you can drive safely and passengers stay protected.

Remember

  • Keep your movement, vision and attention free from obstruction.
  • Check items passengers carry too.
  • Keep access points and passageways clear.
  • Use designated compartments and protect passengers from luggage striking them.
  • Do not carry people in a luggage trailer without authorised passenger places.
  • Coordinate luggage handover and confirm closures before moving off.

Exam trap: Wrong: secured luggage allows a companion in a trailer without passenger places. Right: use only authorised, equipped passenger places.

Read the full explanation
  • You must position objects so that you retain your freedom of movement, the necessary field of vision and your ability to pay attention to driving. A bag beside the pedals or an item encroaching on the driving area prevents you from meeting these conditions, even if the authorised mass is not exceeded. You must also check the objects passengers carry with them. [RGC, art. 18](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a18).
  • You must keep passageways and access points clear; on public passenger transport, you must not allow luggage to obstruct passage unnecessarily. As an organisational guideline, keep suitcases off the steps and out of the aisle and use the designated compartments. [RGC, art. 11](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a11).
  • You must separate luggage from occupants so that items cannot strike them if thrown about. If the vehicle is authorised to carry people and loads at the same time, you must ensure it has protection appropriate to the load. [RGC, art. 10](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a10).
  • You must keep passengers in the places designated and equipped for them. You must not use a luggage trailer with no authorised passenger places to carry passengers or accompanying persons who monitor the load. [RGC, art. 10](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a10).
  • As a service guideline, agree who opens the compartments, hands over luggage and confirms that everything is closed before you move off. Prevent a passenger from retrieving a suitcase while someone else tightens a lashing or closes the tailgate. You must coordinate luggage handling while also supervising the group as they board and alight.

20Projecting loads and their marking

A green minibus travels in the right lane towing a trailer loaded with strapped beams and a red-and-white diagonal warning panel at the rear end of the load.
The key idea

Check how far your load may project and how to mark it.

10 % / 15 %Minibus rear projection
2 m / 3 mTrailer front and rear
0.40 mSide marking threshold
2.55 mMaximum overall width
Vehicle and conditionLimit or marking you must apply
Minibus, projecting loadRear only: up to 10 % of its length; 15 % if indivisible
Goods-only trailer over 5 m long; load indivisible in lengthUp to 2 m in front and 3 m behind; keep it legally stowed and secured
Goods-only trailer 5 m long or less; load indivisible in lengthUp to one third of its length at each end; keep it legally stowed and secured
Goods-only trailer; indivisible load whose smallest dimension exceeds the trailer’s widthUp to 0.40 m on each side; maximum overall width 2.55 m
Rear projection, any vehicleV-20 panel; two panels if it covers the full rear width
Rear projection at night or in significantly reduced visibilityAdd a red light
Permitted front projection at night or in significantly reduced visibilityMark with a white light
Side end more than 0.40 m from the outer edge of the front or rear position light; at night or in significantly reduced visibilityMark each end: white light and reflector at the front; red light and reflector at the rear

Remember

  • Check whether the projection is permitted for the vehicle carrying the load.
  • Protect the projecting end; respect maximum dimensions and the road’s dimension limits.
  • Place V-20 at the rear projecting end, perpendicular to the vehicle’s length.
  • If it covers the full rear width, use two panels in an inverted V.
  • Place each panel at one end, across the vehicle.
  • At night or in significantly reduced visibility, add the required lights.

Exam trap: Wrong: you add the trailer length when working out the minibus overhang. Right: use only the minibus length: rear only, 10 %, or 15 % if indivisible.

Read the full explanation
  • On the minibus, you may carry a load projecting only to the rear: up to 10 % of the length of the minibus, or 15 % if the load is indivisible. You must calculate this using the length of the vehicle carrying the load, without adding the length of the trailer. [RGC, art. 15.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • On a trailer intended exclusively for goods, you may carry a load that is indivisible in length projecting up to 2 m at the front and 3 m at the rear if the trailer is more than 5 m long. If it is 5 m long or less, the limit is one third of its length at each end. You must keep the load stowed and secured in accordance with the regulations. [RGC, art. 15.2.a](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • If the smallest dimension of an indivisible load exceeds the width of that goods trailer, you may carry it projecting up to 0.40 m on each side, with a maximum overall width of 2.55 m. Except where the regulations allow otherwise, you must keep the load within the outline of the vehicle when viewed from above. [RGC, art. 15.1 and 15.2.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • You must protect the projecting end to reduce damage from scraping or collisions and take precautions to protect other road users. You must also comply with the maximum dimensions for the laden vehicle and the dimensional limits of the road; consult «Maximum dimensions and masses» for these clearances and additional authorisations. [RGC, arts. 13 and 15.5](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • You must mark any rear projection with the V-20 panel, positioned at the end of the load and kept perpendicular to the longitudinal axis of the vehicle at all times. If the load projects across the full rear width, you must place two panels transversely, one at each end, forming an inverted V. [RGC, art. 15.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • Between sunset and sunrise, or when visibility is significantly reduced, you must add a red light to the rear projection; you must mark any permitted front projection with a white light. [RGC, art. 15.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • If the outer end of a side projection is more than 0.40 m from the outer edge of the front or rear position light, you must mark each end at night or when visibility is significantly reduced: a white light and reflector at the front, and a red light and reflector at the rear. [RGC, art. 15.7](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).

21Covers and loose material

A minibus travels in the right-hand lane towing a twin-axle trailer whose load is completely covered by a closed green tarpaulin secured around its entire perimeter.
The key idea

Cover materials that produce dust or could fall off completely and effectively.

Remember

  • Cover these materials fully and check that none can escape.
  • Spread loose material without high piles or overloaded axles.
  • Use any lashings or dividers needed for boxes and suitcases.
  • Secure the cover and tidy away ropes and tensioners.
  • Before leaving, remove loose remains and external packaging that could fall off.

Exam trap: Wrong: any tarpaulin works, even torn or open. Right: cover materials completely and effectively.

Read the full explanation
  • If you carry materials that produce dust or may fall off, you must cover them completely and effectively. Assess the result: a tarpaulin that is torn, open at one end or unable to retain the material does not fulfil this function. This obligation also applies to loose material you exceptionally carry in a trailer to support a group activity. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • As a stowage guideline, spread any loose material without creating heaps that unnecessarily raise the centre of gravity or concentrate the mass on one axle. Do not deal with an excess by compressing it beneath a cover. In a luggage trailer, you cannot use a tarpaulin that contains small objects as a substitute for the lashings or dividers needed for boxes and suitcases.
  • You must secure the cover and gather up tensioners, ropes and loose ends so that they cannot strike anything, drag or come loose. You must arrange protective accessories as safely as the load itself. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • Before leaving the loading or unloading site, check the tailgate, edges, platform and exterior components where loose debris may remain. Remove it in a suitable place as a preventive measure. Also check that no bags, straps or packaging are trapped outside the trailer where they could come loose during the journey.

22Keep the road clean and safe

A minibus towing a trailer is stopped beside the right-hand kerb while one person collects gravel beside traffic cones and another checks the trailer latch.
The key idea

Prevent lost loads and deal with the consequences if you create danger.

Remember

  • Do not leave materials that obstruct traffic or damage the road.
  • If you create danger, remove it quickly; meanwhile, make others aware.
  • Take measures to avoid obstructing traffic.
  • After a spill, stop safely, prevent further leaks and request suitable equipment.
  • Do not spread slippery substances with water or push debris towards others.
  • Correct the cause before continuing your journey.

Exam trap: Wrong: cleaning up after losing a load is enough. Right: if you caused danger, address it and correct the cause too.

Read the full explanation
  • You must not throw, deposit or abandon materials that obstruct traffic, make it dangerous or damage the road. You must consider the risk from large items as well as aggregates, mud or liquids that affect grip. You must prevent this through proper loading, secure closures and vehicle cleaning. [RGC, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a4).
  • If you create an obstruction or hazard, you must remove it as soon as possible and, in the meantime, take measures to make other road users aware of it and prevent obstruction to traffic. [RGC, art. 5](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a5).
  • If a spill occurs, you must stop the operation or bring the vehicle to a halt safely, prevent any further material from escaping and request suitable resources to remove it. You must not spread a slippery substance with water or push debris into the path of other road users as an improvised solution.
  • You must check what caused the material to come loose before resuming your journey: a faulty tailgate, an inadequately secured cover, torn packaging or insufficient restraint. Cleaning the affected area does not resolve the cause. For protecting a vehicle immobilised on the road and alerting the emergency services, consult «Responding to accidents and breakdowns».

Plan, distribute and secure

Prepare the luggage and both units before starting the service.

  1. Identify the mass, dimensions and unloading order of suitcases and equipment, also accounting for the passengers in the minibus.
  2. Check the capacities of the vehicles, axles, floor and anchor points.
  3. Distribute the load low down and evenly according to the loading plan.
  4. Prevent dangerous movement through blocking, friction and calculated lashings.
  5. Check supports, equipment, closures, covers and the visibility of lights and plates.
  6. Check the load distribution by weighing if you cannot verify it otherwise, and correct it before setting off.

Carry out partial unloading

The remaining luggage must stay stable and restrained.

  1. Check the stopping location and keep the passengers' route separate from the luggage handling area.
  2. Secure the combination against movement and coordinate the operation with the staff responsible.
  3. Assess whether the load has shifted before opening doors or removing lashings.
  4. Remove the intended items without destabilising those remaining.
  5. Reassess the axle load distribution and restore blocking and lashings.
  6. Close up, remove equipment and debris, and check your surroundings before driving on.

Prepare a liquid container for travel

Prevent a container in the luggage trailer from moving or leaking.

  1. Identify the contents and use a suitable container, following its filling instructions.
  2. Check that it is closed securely and does not leak.
  3. Place it in its designated holder and secure it against shifting and overturning.
  4. Take account of the liquid's internal movement if the container is partially full.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module