Theory · D1+E Licence - Minibus with Trailer · Module 6 of 13

Safety devices on the combination

You learn to recognise and check the devices that keep your minibus and trailer safe and visible: secondary coupling, lights, reflectors, plates, mirrors and protective devices. You learn to choose and use the equipment for securing the combination against movement and dealing with emergencies, and to answer D1+E questions that depend on vehicle width, length, category or number of seats.

34 min read25 sectionsReviewed Nov 3, 2026
A person wearing a reflective vest checks the coupling of a green minibus and orange trailer displaying lights, triangular reflectors, two plates and a wheel chock.
Safety checks for a minibus and trailer

1Each device has a specific function

A person wearing a reflective vest inspects the coupling, breakaway brake cable and electrical connection between a parked minibus and its trailer, whose rear lights are visible.
The key idea

Check each device on your minibus and trailer for its own purpose.

Remember

  • Check the trailer from outside, in safe conditions.
  • Check the coupling, brakes and lights separately.
  • Carry a connected V-16, vest and extinguishers in your non-special combination.
  • Keep compulsory equipment even when driving empty or by day.
  • Use the corrective aids, prostheses or adaptations you need to drive.

Exam trap: Wrong: checking the minibus is enough. Right: check the trailer’s devices too.

Read the full explanation
  • The mechanical coupling keeps the two units together; the breakaway braking device stops the trailer if the coupling fails; the lights signal your presence and manoeuvres. When inspecting the combination, check mechanical retention, braking and lighting separately. [RGV, arts. 12 and 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • With your minibus and trailer, you must also check the towed unit. From the cab, you may receive warnings or see some devices, but you must supplement that information with an exterior inspection in safe conditions. Having working lights on the towing minibus does not prove that the trailer lights work.
  • Your combination (other than a special vehicle combination) must carry the compulsory equipment listed in RGV Annex XII: a connected V-16, a high-visibility vest and fire extinguishers. [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • You must retain the devices required for the vehicle even when you drive empty, in daylight or on a short journey. The equipment required depends on its technical characteristics and the regulatory conditions of use; the MMA (maximum authorised mass) remains the mass authorised in the documentation even when you carry less luggage. [RGV, arts. 16 and 19](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • In the D1+E test, the examiner may check that you have suitable protective equipment where applicable. You must have the corrective aids, prostheses or adaptations you need to drive; sunglasses or a clothing preference do not replace these items. This general check does not require you to wear the clothing used for a motorcycle test. [RGCond, art. 57.2 and Annex VI, C.1](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a57).

2Secondary safety coupling

A green minibus with an orange trailer is stopped beside the kerb, with the main coupling separated and a safety chain connecting the trailer drawbar to the vehicle above the ground.
The key idea

You need a secondary coupling on certain trailers without braking when the coupling breaks.

1,500 kgMaximum MMA for this rule

Remember

  • Check your trailer’s MMA and its braking system for separation.
  • The secondary coupling supports the drawbar and keeps some steering control.
  • Check its attachment points and routing.
  • Do not continue your journey with a broken coupling.

Exam trap: Wrong: every trailer needs the same chain. Right: this requirement applies when MMA does not exceed 1,500 kg and no system ensures braking if the coupling breaks.

Read the full explanation
  • If you tow a trailer with an MMA not exceeding 1,500 kg without a system that ensures braking if the coupling breaks, it must have a secondary coupling in addition to the main one. The rule allows a chain, cable or other device that performs the required function; the material alone does not identify its purpose. [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • If the main coupling separates, this secondary coupling must prevent the drawbar from touching the ground and retain some residual steering of the trailer. Its two purposes are to support the drawbar and maintain a limited ability to guide the trailer; this does not mean you can continue your journey with a broken coupling. [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • The safety chain acts as a mechanical restraint if the main coupling fails. You must inspect its links, end fittings and the anchor points specified by the manufacturer; its strength depends on all the components and on their being correctly secured.
  • The 1,500 kg limit refers to the trailer's MMA and applies in conjunction with the absence of the breakaway braking system described. For the trailer you couple, you must consult the documentation and instructions to check which device is required and where it attaches; the presence of a chain alone does not identify the type-approved safety system. [RGV, art. 13.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).

3Breakaway cable and automatic braking

A person checks the orange breakaway cable attached between the trailer and a minibus stopped beside the right-hand kerb.
The key idea

Check that the emergency system can stop your trailer if it separates.

Remember

  • Attach the breakaway cable where the manufacturer specifies.
  • Follow its routing instructions to avoid pulling during normal manoeuvres.
  • Check the connections of the braking system fitted to your trailer.
  • Check cables, chains, hooks and fastenings.
  • Fix damage before setting off.
  • Never separate the combination while moving to test the system.

Exam trap: Wrong: the chain and breakaway cable do the same job. Right: identify whether each maintains the connection or applies the brake.

Read the full explanation
  • The automatic braking devices on a trailer or semi-trailer must ensure that it stops automatically if it becomes uncoupled or the coupling breaks while travelling. You must keep the breakaway system specified in the trailer's type approval operational. [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • If the equipment uses a breakaway cable that applies the brake on separation, you must attach it to the specified point and follow the routing specified by its manufacturer. The installation must allow it to operate when the units separate and leave enough freedom for the combination's normal turns.
  • On your D1+E combination, you may find a breakaway cable associated with the overrun brake or the emergency device for another type of braking equipment. Check the connections of the installed system: its configuration depends on the trailer's braking equipment. The operation of the circuits is covered in «Trailer and combination braking». [RGV, arts. 12.8 and 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • Visually check the condition of accessible cables, chains, hooks and fastenings, looking for breaks, deformation or incorrect installation. As a safety precaution, rectify any defect before driving and follow the system manual; do not test its operation by causing the combination to separate while moving.

4Connections and safety locks before driving

A crouching driver checks the coupling and connections between a green minibus and an orange trailer parked beside a kerb.
The key idea

Check that your connections are compatible, secured and allow the combination to turn.

ItemWhat you must ensure
Brake and chocksPrevent movement
SupportsHold up the trailer when uncoupled

Remember

  • Check the coupling closure and safety lock before starting or resuming your journey.
  • Check connections even with an empty trailer.
  • Keep cables from dragging, becoming trapped or stretching too tightly.
  • Raise and secure the jockey wheel and supports before driving.
  • Before uncoupling, secure the trailer against movement and position its supports.

Exam trap: Wrong: parts that fit together are compatible. Right: check their technical compatibility too.

Read the full explanation
  • The mechanical, pneumatic and electrical components between the towing vehicle and trailer must be compatible. You must check that each connection is correctly coupled and secured; being able to physically join two components is not enough to prove their technical compatibility. [RGV, art. 13.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Before setting off or resuming your journey, check the main coupling's closure, locking mechanism and safety lock as appropriate for the model. Then check the auxiliary connections and devices, including in dry weather or with an empty trailer. The check must cover accessible retaining components and any closure indicators fitted to the equipment.
  • Allow the connections enough movement for the combination to articulate, preventing them from dragging, becoming trapped or being placed under undue tension. Functional slack must coexist with secure fastening. As a practical check, make sure the jockey wheel or other supports are retracted and secured before moving.
  • Before uncoupling the trailer, you must secure it against movement and leave it supported on the supports provided for its design. The full procedure is covered in «Coupling and uncoupling the trailer»; the brake and chocks prevent movement, while the supports hold up the part that loses the support of the minibus. [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).

5Position lights and number plate lighting

A minibus towing a trailer travels at night in the right lane, with the trailer’s two red rear position lights on and a white lamp illuminating its rear registration plate.
The key idea

Check your trailer’s position lights and number plate lighting.

1.60 mFront position light threshold
Non-agricultural trailer lightingColourRequirement
Rear position lightsRedTwo compulsory lights
Front position lightsWhiteTwo compulsory above 1.60 m wide; optional at or below
Rear number plate lightingWhiteCompulsory

Remember

  • Keep your trailer’s lights and number plate visible.
  • Use position lights at night, in poor visibility, tunnels and underpasses.
  • Check the rear number plate lighting too.
  • Do not rely only on the minibus’s daytime running lights.

Exam trap: Wrong: exactly 1.60 m requires front position lights. Right: on non-agricultural trailers, they are compulsory above that width.

Read the full explanation
  • Your non-agricultural trailer or semi-trailer must have two red rear position lights. You must check that they are visible from behind and indicate the vehicle's presence and outline. The trailer body may hide the minibus lights from those travelling behind. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The towed vehicle has two white front position lights; they are compulsory when its width exceeds 1.60 m and optional when it is equal to or less than this. When inspecting a wide trailer, you must view these lights from the front and check that accessories do not obscure them. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The towed vehicle must have white lighting for the rear number plate. You must check that it allows the plate to be identified and is not obscured by mud, open doors, brackets or accessories. The number plate and the light illuminating it are separate items, and both must retain their function. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • When driving at night, in significantly reduced visibility or through tunnels and underpasses, you must keep the combination's required position lights on. The rear number plate must be illuminated in the circumstances required by the regulations; the towing minibus's daytime running lights alone do not prove that all these lights are on. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99). [RGC, art. 103](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a103).

6Brake lights, indicators and hazard warning lights

A person watches from the side as the amber hazard lights operate on a minibus and trailer secured with wheel chocks, with both rear trailer indicators illuminated.
The key idea

Check your indicators, hazard warning lights and brake lights separately.

Non-agricultural trailer lightsColour and arrangement
Rear indicatorsAmber; an even number
Hazard warning lightsUse the indicators, with the same colour and arrangement
Brake lightsTwo red lights

Remember

  • Check the indicators on both sides of your trailer.
  • Check hazard warning lights on the minibus and trailer.
  • Apply the brake to check its lights.
  • Keep the combination secured against movement during checks.
  • Keep people away from between or behind units that could move.

Exam trap: Wrong: working position lights prove the brake lights work. Right: check each function separately.

Read the full explanation
  • Your non-agricultural trailer must have amber rear direction indicators, fitted in an even number. You must check both sides: a fault on one side may leave you unable to signal precisely the manoeuvre you need to make when joining traffic or changing course. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The hazard warning signal uses the direction indicators, with the same colour and arrangement. You must check that it works on the towed vehicle and the minibus; activating the hazard warning switch does not prove that the lamps at the rear end receive power. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The towed vehicle has two red brake lights according to the general table in Annex X. You must check their response when you apply the brake, distinguishing them from the position lights: they share a colour, but warn of different situations, and you cannot consider one function checked by looking only at the other. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • As a practical check, use someone observing from a safe place or a method that allows you to verify each function properly. Do not place anyone between the units or behind a combination that could move. You must carry out the check with the vehicle secured against movement and the controls operated in a controlled manner.

7End-outline marker lamps: recognising width

A minibus tows a wide box trailer in the right lane of a road at dusk, with the two red clearance lamps illuminated at the trailer’s upper rear corners.
The key idea

Check whether your trailer needs end-outline marker lamps by its width, not its mass.

2.10 mCompulsory above this width
Trailer end-outline marker lampsNumberColour
FrontTwoWhite
RearTwoRed

Remember

  • Look for end-outline marker lamps at the upper edges.
  • Check that none are missing, hidden or damaged.
  • Switch required lamps on with position lights at night and in poor visibility.
  • Also use them in tunnels, underpasses and signed tunnel sections, even by day.

Exam trap: Wrong: exactly 2.10 m requires end-outline marker lamps. Right: the trailer or semi-trailer must exceed that width.

Read the full explanation
  • If your trailer or semi-trailer is more than 2.10 m wide, it must have end-outline marker lamps. You must associate them with width, rather than mass or the need for D1+E. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • End-outline marker lamps are white at the front and red at the rear, with two front lamps and two rear lamps in the equipment specified for trailers. Their position makes the vehicle's upper outer edges recognisable. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must switch on the required end-outline marker lamps together with the position lights between sunset and sunrise, when visibility is significantly reduced and when passing through tunnels, underpasses or stretches signposted as tunnels. This obligation also applies when you pass through during the day. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99).
  • During your exterior inspection, look at the high points of the towed vehicle and check that no lamps are missing, obscured or damaged. On a tall box body, checking only the lower light clusters leaves unchecked the very devices that help others judge its size.

8Trailer side marking

A green minibus travels to the right along a road, towing a long blue trailer with three illuminated amber side marker lights and rectangular reflectors below them.
The key idea

Tell your trailer’s side lamps apart from its side reflectors.

6 mSide lamps compulsory above
Non-agricultural trailersWhen compulsory
Side marker lampsWhen the trailer exceeds 6 m
Non-triangular side reflectorsRegardless of the length threshold

Remember

  • Measure the trailer’s length, not the whole combination.
  • Check both sides and remove anything hiding lamps or reflectors.
  • Recognise the amber colour of side lamps.
  • The rearmost may be red when integrated with certain permitted rear devices.

Exam trap: Wrong: side reflectors are compulsory only above 6 m. Right: that threshold applies to side lamps on non-agricultural trailers.

Read the full explanation
  • Side marker lamps are compulsory on non-agricultural trailers longer than 6 m. When determining the required equipment, this condition applies to the length of the trailer, even if the combined length of the minibus and a shorter trailer also exceeds 6 m. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • Side marker lamps are amber, and their number depends on the length and installation requirements. UN Regulation 48 allows the rearmost lamp to be red when it is integrated with certain rear devices. These powered lamps show the side of the trailer when it crosses another road user's path; you must check that they light up on both sides. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx). [UN Regulation 48, para. 5.15](https://www.boe.es/doue/2021/347/L00001-00122.pdf).
  • Non-triangular side reflectors are compulsory on non-agricultural trailers, and article 16.5 does not make this requirement subject to the 6 m threshold. You must avoid applying the length requirement for side marker lamps to all reflective devices on the sides. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • As an inspection routine, walk along both sides: a check from behind can miss side lamps and reflectors. Make sure toolboxes, tarpaulins, dirt or repairs do not obscure them.

9Fog lights and reversing lights

A minibus towing a trailer travels in the right-hand lane through dense fog with the trailer’s red rear fog lamp illuminated.
The key idea

Use rear fog lights only in particularly bad conditions and keep required reversing lights.

6 mReversing light threshold
Trailer length (O2, O3 and O4 trailers subject to UN Regulation 48)Compulsory reversing lightsOptional reversing lights
Up to 6 mOne deviceOne additional device
Above 6 mTwo devicesTwo devices

Remember

  • Check the red rear fog lights: your trailer has one or two.
  • Use only in thick fog, very heavy rain, heavy snow, dense dust or smoke.
  • Keep the white reversing lights required by your trailer’s type approval.
  • Check mirrors and blind spots before reversing.
  • A reversing light does not prove the space is clear.

Exam trap: Wrong: you may remove reversing lights because the general table calls them optional. Right: keep the equipment required by your trailer’s type approval.

Read the full explanation
  • Your non-agricultural trailer must have a red rear fog light; the table in Annex X provides for one or two. You must check this function specifically, because you cannot infer its presence or operation from the position lights or brake lights coming on. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must switch on the rear fog light only in particularly adverse weather or environmental conditions, such as thick fog, very heavy rain, heavy snowfall or dense clouds of dust or smoke. Do not use it simply because it is night-time or because you are driving a large vehicle. [RGC, art. 106.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • Reversing lights are white. Although the general table in Annex X of the RGV lists them as optional, UN Regulation 48 requires this function on O2, O3 and O4 trailers subject to its provisions: one compulsory lamp and one optional lamp up to 6 m in length, and two compulsory lamps and two optional lamps above 6 m. You must retain the equipment required by your trailer's type approval; you cannot infer from the general table that you are allowed to remove them. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx). [UN Regulation 48, paras. 6.4.1 and 6.4.2](https://www.boe.es/doue/2021/347/L00001-00122.pdf).
  • If your combination has reversing lights, you must check that they indicate this manoeuvre and cannot be confused with a red braking signal. They help warn others of the movement, but do not show that the area is clear or replace looking in your mirrors and checking blind spots. [RGC, art. 109.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).

10Reflectors: shape and colour

A minibus towing a trailer travels in the right lane of a rural road, with the two red triangular reflectors visible on the rear of the trailer.
The key idea

Recognise your trailer’s reflectors by their shape, colour and position.

2.10 mAdditional rear reflectors: above
Trailer reflectorsShape and colourEquipment
RearRed trianglesTwo compulsory
FrontWhite, non-triangularTwo compulsory
SideAmber, non-triangularRearmost red only in the permitted arrangement
Additional rearRed, non-triangularTwo optional when width exceeds 2.10 m

Remember

  • Keep reflectors clean and undamaged.
  • Remember that they reflect light; they do not produce it.
  • Do not use them to replace compulsory lights.
  • The rearmost side reflector may be red when grouped with permitted rear devices.
  • Sharing a light-emitting surface with permitted rear devices also allows this exception.
  • Keep the type-approved arrangement.

Exam trap: Wrong: replace rear triangles with red rectangles. Right: keep the compulsory triangles even with additional reflectors.

Read the full explanation
  • Your trailer or semi-trailer must have two red triangular rear reflectors. Their shape identifies the towed part of the combination when light from another vehicle falls on them; you must keep both in their correct positions with their reflective surfaces intact. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Your towed vehicle has two white, non-triangular front reflectors. They reflect incoming light and work without an electrical supply. You must also inspect their surfaces with the lights switched off to detect cracks, detachment or covered areas. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Side reflectors are non-triangular and amber. The rearmost one may be red when it is grouped with, or shares a light-emitting surface with, rear devices permitted by the regulations, such as a position light, brake light or non-triangular rear reflector. You must retain the approved configuration; this exception does not allow you to choose the colour of all the side reflectors freely. [UN Regulation 48, para. 5.15](https://www.boe.es/doue/2021/347/L00001-00122.pdf).
  • A reflector does not itself produce the light that makes it visible. You must therefore keep it clean and intact even when the entire electrical system works. Likewise, reflectors do not replace compulsory lights or allow you to drive with an unresolved connection fault.
  • The RGV table also provides for two optional red non-triangular rear reflectors on trailers wider than 2.10 m. If your trailer has them, you must recognise them as additional devices: the two compulsory rear triangles retain their function of identifying the trailer. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).

11Checking lights and visibility

A person checks the two illuminated, symmetrical red rear lights of a trailer attached to a minibus parked beside the right-hand kerb.
The key idea

Check every lighting function and keep the parts you need for visibility clean.

Remember

  • Check each light, even when several share a housing.
  • Keep windows, mirrors, lights and reflectors clean.
  • Keep paired lights matched in colour, brightness and prescribed symmetrical position.
  • Fix faults that prevent correct signalling before setting off.
  • Reduce speed if an unrepairable fault during your journey makes lighting less bright.
  • You must be able to stop within the lit area.

Exam trap: Wrong: every lighting fault allows you to continue slowly. Right: assess the fault and arrange repair or assistance when needed.

Read the full explanation
  • Paired devices with the same purpose must match in colour and intensity and be positioned symmetrically as required by the regulations. You must avoid improvised repairs that change the colour or leave a signal that is difficult to interpret; a lamp that emits light does not necessarily fulfil its regulatory function. [RGV, art. 15.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15).
  • Check, in turn, the position lights, number plate lighting, indicators on each side, hazard warning lights, brake lights, end-outline marker lamps and side marker lamps where required, as well as any other functions fitted. An orderly inspection prevents you from mistaking an illuminated light cluster for a check of every function it incorporates.
  • Keep windows, mirrors, lights and reflectors clean so that you can see and be seen; cleaning the floor or bodywork does not serve this purpose. The minibus's interior lighting does not replace the exterior lights. As a safety precaution, resolve any fault that prevents the trailer's presence or manoeuvres from being clearly signalled before you set off.
  • If a fault that cannot be repaired en route forces you to drive with reduced lighting intensity, you must reduce your speed until you can stop within the illuminated area. This rule does not make every loss of trailer signalling permission to continue: assess the fault and arrange the necessary repair or assistance. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107).

12Two number plates at the rear

Rear view of an orange trailer hitched to a green minibus, with a centered red plate and a white plate to its right, both without characters.
The key idea

Carry your trailer’s own plate and your towing minibus’s plate at the rear.

750 kgTwo plates above this MMA
Trailer with MMA above 750 kgRear positionAppearance
Own number plateCentred; vertical or nearly verticalRed background, black characters
Towing minibus’s plateRight-hand sideIdentifies the towing vehicle

Remember

  • Check that plates are secure, clean and visible.
  • If you change towing minibuses, change the plate showing the towing vehicle’s registration.
  • Do not confuse the trailer’s red plate with a load sign.

Exam trap: Wrong: any arrangement of plates is enough. Right: centre the trailer’s own plate and place the towing vehicle’s plate on the right.

Read the full explanation
  • Your D1+E trailer, with an MMA (maximum authorised mass) above 750 kg, must display its own number plate at the rear and a second plate bearing the registration number of the minibus towing it. The two registrations serve different purposes: one identifies the trailer and the other identifies the vehicle towing it. [RGV, Annex XVIII, III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • The trailer's own number plate must be vertical or almost vertical and in the towed vehicle's median longitudinal plane. The plate displaying the towing minibus's registration number is placed on the right-hand side. You must pay attention to their positions and avoid answering that any arrangement is sufficient as long as there are two plates. [RGV, Annex XVIII, section III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • The standard number plate for trailers and semi-trailers has a red background and black characters. The standard plate corresponding to the towing vehicle bears its own regulatory identification; you must avoid confusing the red of the trailer's number plate with a danger or load warning sign. [RGV, Annex XVIII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • If another minibus takes over towing the trailer, change the plate displaying the towing vehicle's registration number so that it matches the actual combination. During your exterior inspection, check that the plates are secure and clean, and that luggage, brackets or accessories do not obscure characters or signalling devices. [RGV, Annex XVIII, III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).

13Long vehicle rear plate

A minibus towing a trailer travels in the right lane with a yellow plate with a red border centered on the rear of the trailer, separate from the registration plate and triangular reflectors.
The key idea

Fit the long vehicle sign if your combination exceeds the stated length.

12 mV-6 required above this length
500 mmMinimum fitting height
1,500 mmMaximum fitting height

Remember

  • Measure the whole combination, not just the trailer.
  • Fit V-6 at the rear, centred.
  • You may use two similar plates, positioned symmetrically near the edges.
  • Use a type-approved sign with yellow reflective and red fluorescent material.
  • Keep number plates and other required signs too.

Exam trap: Wrong: exactly 12 m requires V-6. Right: the vehicle or combination must exceed 12 m.

Read the full explanation
  • The V-6 sign, Long vehicle, indicates that the vehicle or combination exceeds 12 m in length. You must consider the whole combination: you may need it even if each individual unit is shorter. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • You must fit it at the rear, centred on the vehicle's longitudinal centreline. Where this makes fitting easier, you may use two similar plates positioned symmetrically on either side of the centreline and as close to the edges as possible. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • You must fit it between 500 and 1,500 mm above the ground. The sign has yellow reflective material and red fluorescent material and must be type-approved. You must keep it visible from behind and check that its mounting maintains the required height and orientation. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • Distinguish the V-6 from number plates, the trailer's reflective triangles and the marking panel for a projecting load. Each item has its own purpose and requirement; carrying one does not exempt you from carrying any others that apply. Load marking is covered in «Safe loads and luggage».

14Reflective contour markings

A minibus with a trailer is parked beside the right-hand kerb, with yellow contour strips on the trailer separate from the lights and red triangular reflectors.
The key idea

Check reflective marking against your trailer’s category, configuration and dimensions.

2.10 mRear contour required above
6 mSide contour required above
Complete O3 and O4 trailersRequired marking
Wider than 2.10 mFull rear contour
Longer than 6 m, including the drawbarPartial side contour

Remember

  • You do not need V-23 simply because you tow with a minibus.
  • Keep the type-approved marking required for your vehicle.
  • Check that repairs do not leave strips incomplete.
  • Keep strips clean and undamaged.
  • Check lights too: reflective strips do not replace them.

Exam trap: Wrong: every minibus trailer needs the same marking. Right: check its category, configuration and dimensions.

Read the full explanation
  • The V-23 sign, Goods vehicle identification marking, consists of reflective markings that increase the visibility and recognition of the vehicle or combination. Its strips reflect incoming light and outline the vehicle's dimensions; you must maintain the arrangement specified in its type approval. [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23).
  • The V-23 is not compulsory simply because you drive a minibus with a trailer. Under UN Regulation 48, complete O3 and O4 trailers require full rear contour markings if they exceed 2.10 m in width, and partial side contour markings if they exceed 6 m in length, including the drawbar. You must apply the requirements for the trailer's category and configuration and maintain the markings specified in its type approval. [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23). [UN Regulation 48, para. 6.21.1.2](https://www.boe.es/doue/2021/347/L00001-00122.pdf).
  • The material must be type-approved under UNECE Regulation 104 and its installation must meet the prescribed technical conditions. As the driver, you must maintain the arrangement required for the vehicle and check that repairs to the bodywork or tarpaulins have not left it incomplete. [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23).
  • As a practical guideline, inspect the strips from different angles during your walk-round check. A strip covered in mud or damaged loses its usefulness even if it remains attached to the vehicle. You must also check the lights: reflective markings help others judge the vehicle's dimensions and do not replace the lights' electrical supply.

15Mirrors on the towing minibus

A green minibus with an orange trailer is stopped beside the kerb on its right, with a driver at the wheel and both main exterior mirrors visible.
The key idea

Keep your compulsory exterior mirrors and adjust them before driving.

2 mClass V must exceed
Mirrors on M2 and M3PurposeRequirement
Class IIMain exteriorCompulsory on left and right
Class IVWide-angleOptional under applicable provisions
Class VClose-proximityOptional; entire assembly above 2 m in every adjustment, fully laden
Class VIFrontOptional; no point of the mirror or its supports below 2 m in any adjustment, with the vehicle at its technically permissible maximum mass

Remember

  • Keep the main exterior mirrors on both sides.
  • Adjust mirrors while stationary, with your seat correctly positioned.
  • Clean the glass and check the mountings.
  • Keep the type-approved arrangement.
  • Do not fit class V mirrors unless their height complies when fully laden.
  • Do not fit class VI mirrors if cab height prevents meeting the minimum height.

Exam trap: Wrong: the passenger mirror replaces an exterior mirror. Right: on M2 and M3, you need both main exterior mirrors.

Read the full explanation
  • For categories M2 and M3, used for passenger transport, the RGV table requires two class II main exterior mirrors: one on the left and one on the right. You must retain both; an interior mirror used to monitor passengers does not replace the compulsory exterior view. [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • Class IV is the wide-angle mirror and class V is the close-proximity mirror; both are optional on M2 and M3 vehicles. Class V mirrors must remain more than 2 m above the ground in every adjustment position, including adjustment points and attachments, with the vehicle fully laden. If the cab height prevents compliance with this condition, fitting them is prohibited. You must maintain the minibus's type-approved configuration. [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • The class VI front mirror shows the area immediately in front of the minibus and is optional on M2 and M3 vehicles. If you fit one, no part of the mirror or its supports may be less than 2 m above the ground in any adjustment position, with the vehicle at its technically permissible maximum mass. If the cab height prevents compliance, fitting it is prohibited. [UN Regulation 46, paras. 15.2.1.1.1 and 15.2.2.7](https://www.boe.es/buscar/doc.php?id=DOUE-L-2010-81254).
  • You must adjust the mirrors with the combination stationary, after positioning yourself correctly in the seat. Check both sides and nearby areas, keep the glass clean and check that the supports do not vibrate or move out of position. Poor adjustment reduces the information available even in daylight.

16Extension mirrors and blind spots

A driver adjusts the extended left mirror of a stationary green minibus with an attached orange box trailer, whose side is reflected in the mirror.
The key idea

Adapt your mirrors if the trailer blocks the view you need.

Remember

  • Check your view with the trailer coupled.
  • Use suitable extensions if needed to restore the required view.
  • Secure them so they keep their alignment.
  • Remember that mirrors leave some areas unseen.
  • Your view in each mirror changes as the combination turns.
  • If you lose a reference needed for manoeuvring, stop and check your surroundings.

Exam trap: Wrong: towing always requires extending mirrors. Right: you need a suitable solution if you lack the required field of vision.

Read the full explanation
  • If the towed vehicle obstructs the necessary field of vision, you must use a suitable indirect vision system that meets the vehicle's technical requirements. Extension or supplementary mirrors may provide the necessary view; you must not fit them on the basis of an automatic rule simply because you are towing a trailer. [RGV, art. 11.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11). [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • As an adjustment guideline, check the field of vision with the trailer actually coupled. An adjustment that works when driving the towing vehicle alone may be insufficient with a wider trailer body or one in a different position. Secure supplementary mirrors so that they maintain their orientation and do not create dangerous projections.
  • The mirrors help you monitor the sides, the towed vehicle and the nearby space, but you must know which areas they do not show. As the combination articulates, the view in each mirror changes; do not assume that a road user has left the danger area because they have disappeared from the mirror.
  • If you lose a reference point you need for manoeuvring, stop and check your surroundings safely. Having mirrors, keeping them clean and adjusting them correctly are complementary checks: none replaces the others or your continuous observation.

17Wheel chocks on a significant slope

A green minibus with a trailer is parked uphill beside the right-hand kerb, with orange wheel chocks against the downhill side of a minibus wheel and the trailer wheel.
The key idea

Secure your combination on a significant gradient when you leave the driving position.

Steered wheel resting against a kerbWhere you turn the wheels
UphillTowards the centre of the carriageway
DownhillOutwards, away from the carriageway

Remember

  • When stopping or parking on a significant gradient, secure wheels before leaving your seat.
  • Add this precaution to the normal measures against movement.
  • Use suitable chocks, never stones.
  • You may rest a steered wheel against a kerb that can hold it.
  • Do not invent a percentage for a significant gradient.
  • Remove and store chocks before driving again.

Exam trap: Wrong: the brake is enough on a significant gradient. Right: when stopping or parking and leaving your driving position, also secure the combination with chocks or the prescribed wheel support.

Read the full explanation
  • If you stop or park your minibus with a trailer on a significant slope and leave the driving seat, you must secure the combination against rolling in addition to taking the usual measures to immobilise it. The rule expressly includes both buses and combinations, so it does not depend on how many passengers you carry. [RGC, art. 92.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).
  • You may do this using purpose-made wheel chocks or by resting a steered wheel against the pavement kerb. If you use the latter method, turn the wheels towards the centre of the carriageway when facing uphill and outwards when facing downhill. There must be a kerb against which the wheel can rest. [RGC, art. 92.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).
  • You must not use stones or other objects not specifically intended for chocking vehicles. You must use a chock suitable for the equipment, position it according to the instructions and check that it performs its function. The parking brake and the selected gear do not remove the additional precaution required on a significant slope. [RGC, art. 92.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).
  • Article 92.3 does not set a general percentage to define a significant slope. You must assess the situation without inventing a numerical threshold for applying the rule. When you move off again, remove the chocks from the road and stow them in the vehicle so that they do not become obstacles. [RGC, art. 92.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).

18Parking brake and supports

A detached trailer behind a parked minibus has its parking brake raised, chocks on both sides of the wheel and its jockey wheel resting on the pavement.
The key idea

Secure your combination and distinguish the trailer’s brake from its supports.

Transmission when leaving your driving positionPosition you leave selected
Manual, uphillFirst gear
Manual, downhillReverse
Transmission with a parking positionParking position

Remember

  • Leaving your seat: stop the engine, switch off ignition and apply the parking brake.
  • If you may walk away, prevent unauthorised use.
  • Check the trailer’s parking brake before uncoupling.
  • The jockey wheel supports the trailer; it replaces neither brakes nor necessary chocks.
  • Keep passengers away from the coupling area.
  • Before driving, secure coupling and connections, raise supports and remove chocks.

Exam trap: Wrong: the jockey wheel alone prevents movement. Right: use the brake and necessary additional measures.

Read the full explanation
  • When you leave the driving seat, you must stop the engine, switch off the ignition and leave the parking brake applied. If you may move away from the vehicle, you must prevent unauthorised use. With a manual gearbox, you must leave it in first gear when facing uphill and reverse when facing downhill; with a system that provides a parking position, you must select that position. [RGC, art. 92.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).
  • The trailer's parking brake allows you to keep it stationary even when it is uncoupled. As a safety guideline, check that it is applied before separating the trailer and maintain any necessary additional measures to prevent movement. You may have the lights and cable correctly connected and still have a trailer that is insufficiently secured against movement. [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • The jockey wheel and other supports hold up the front of the trailer when required; they do not replace the brake or any necessary chocks. As a practical guideline, check the condition of the locking mechanism, the stability of the supporting ground and the surrounding space, keeping passengers out of the coupling area.
  • Before driving again, check that the coupling is secure, the connections are in place and the supports are retracted and secured; remove the chocks once the combination is secured. Check that the locking mechanisms keep each support in its transport position during turns and over uneven road surfaces.

19Rear underrun protection

A green minibus travels in the right lane towing an orange trailer whose rear underrun protection bar is secured by two brackets.
The key idea

Check the rear protection that prevents another vehicle from going underneath.

550 mmMaximum clearance: alternative solution
100 mmMaximum inward distance each side
Vehicle category or exemptionRear protection
M2, M3 and O2One allowed solution: unladen clearance at most 550 mm; protected width reaches within 100 mm inwards per side relative to the rear axle
O3 and O4Their own dimensional and strength requirements
Exemption because protection conflicts with vehicle useMust be recorded in the documentation

Remember

  • Check the rear bar or structure and its mountings.
  • Keep it correctly positioned for driving.
  • Protection may form part of the vehicle’s strong structure.
  • Check both measurements for the applicable alternative, not just height.
  • Damaged protection does not count as an exemption.

Exam trap: Wrong: 550 mm applies to every trailer. Right: this alternative is for M2, M3 and O2, unladen and with the required protected width.

Read the full explanation
  • Vehicles, including trailers and semi-trailers, must provide effective rear protection against other vehicles running underneath them. This can be achieved through a dedicated device or through the shape and structural strength of the rear of the vehicle. You must maintain its strength and secure attachment so that it can perform its function in a rear impact. [RGV, art. 11.16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11). [RGV, Annex IV](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniv).
  • For M2 and M3 vehicles and O2 trailers, Annex IV permits different rear protection solutions. One requires that, when unladen, the ground clearance beneath the rear does not exceed 550 mm across a width extending to within no more than 100 mm of each end of the rear axle. You must consider both measurements together; the other technical solutions specified in that annex are also permitted. [RGV, Annex IV, 2.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniv).
  • If your trailer is in category O3 or O4, you must observe the dimensional and strength requirements for its rear device or structure; the 550 mm alternative is not a universal rule for these trailers. Incompatibility between the protection and the use of the vehicle only qualifies for the specified exemption when it is recorded in the vehicle documentation. [RGV, Annex IV, 2.1 and 3.3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniv).
  • As a checking guideline, check that the bar or structure is not deformed or detached and that its mountings are undamaged. If a device can move to allow work to be carried out, follow the instructions to put it in its driving position.

20Side and front protection

A person checks the attachment of the side guard on a cargo trailer coupled to a minibus parked beside the right-hand kerb.
The key idea

Check the protection required by your combination’s type approval and technical documents.

ProtectionVehicles covered by the requirement
SideGoods vehicles and their trailers where their technical regulations require it
Front underrunGoods vehicles where their technical regulations require it

Remember

  • Check whether your trailer needs side protection.
  • Check its condition, continuity and attachment.
  • Do not remove protection to gain space.
  • Do not assume a toolbox is a valid replacement.
  • Report missing, damaged or incorrectly positioned protection.

Exam trap: Wrong: your minibus needs a lorry’s protection. Right: check the technical requirements for your vehicle and trailer.

Read the full explanation
  • The side protection requirements in article 11 apply to vehicles intended to carry goods, including their trailers, where the technical regulations require it. You must check which equipment requirements apply to the trailer in your combination, without imposing an obligation on the minibus by treating it as a lorry. [RGV, art. 11.17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).
  • Side protection helps prevent a road user from ending up underneath the vehicle in a side collision. As a safety guideline, check its continuity, condition and secure attachment. You must not remove it to gain space or assume that a toolbox mounted on the side is, by itself, a substitute for regulation protection.
  • The front underrun protection in article 11.18 is required on goods vehicles where their technical regulations specify it. On your minibus, you must maintain the components specified in its type approval and check their mountings; the required equipment is determined by its category and technical characteristics. [RGV, art. 11.18](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).
  • To establish exactly which equipment your combination must retain, you must refer to its type approval, configuration and technical documentation. Your check as a driver consists of identifying missing, damaged or incorrectly positioned equipment and reporting it so that it can be put right; it does not replace strength requirements with a visual assessment.

21Connected V-16 and compulsory equipment

A minibus towing a trailer is stopped beside the right-hand kerb with a connected V-16 beacon illuminated on its roof and its hazard lights on.
The key idea

Carry a valid connected V-16 in your Spanish-registered minibus and trailer combination.

Remember

  • Check its make and model on the official DGT list.
  • Do not rely only on an approval label.
  • Check when its connectivity service expires.
  • Keep the beacon accessible from the cab.
  • Maintain its power supply according to its instructions.

Exam trap: Wrong: triangles or an unconnected beacon are enough. Right: carry the regulatory connected V-16 in your Spanish-registered combination.

Read the full explanation
  • You must carry a valid connected V-16 in your minibus and trailer combination registered in Spain. The required equipment for the bus or coach and for a non-special vehicle combination includes this regulation advance warning device. It must be certified and have an active communications service. [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii). [DGT, V-16 devices](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).
  • The V-16 emits an amber light to warn of the presence of the immobilised vehicle. You must use a certified model with a mounting system suitable for the surface where you intend to place it, so that it remains stable during operation. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • You must check that the make and model appear on the official list of certified devices published by the DGT. A commercial label stating that it is approved, or an appearance similar to another beacon, is not enough. Also check the expiry date of the connectivity service marked on the device. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • Keep the beacon somewhere accessible from the cab and maintain its power supply in accordance with the instructions. You must be able to use it when your vehicle becomes immobilised, without having to search through the load or walk along the arcén (hard shoulder) to a distant compartment. [DGT, V-16 devices](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).

22What the beacon must do

A green minibus towing a trailer is stationary on the right shoulder of a rural road, with an illuminated V-16 beacon on its roof emitting light in all directions.
The key idea

Check your beacon’s capabilities and request any assistance separately.

360 degreesHorizontal light coverage
30 minutesMinimum time at required brightness
100 secondsLocation update interval
12 yearsMinimum included communications

Remember

  • Do not switch the beacon off while you still need to warn of danger.
  • The beacon communicates its activation, location and deactivation.
  • You do not need an external mobile app for its communications.
  • The price includes communications for the minimum period.
  • Request the assistance you need through suitable channels.

Exam trap: Wrong: V-16 guarantees an ambulance will come. Right: it transmits location; you must request the help you need.

Read the full explanation
  • The horizontal light coverage of the V-16 is 360 degrees and its regulation light intensity must be maintained for at least 30 minutes. These 30 minutes describe a minimum capability of the device, not permission to switch it off while a situation requiring a warning persists. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The beacon communicates its activation, deactivation and location to the national access point for traffic and mobility. Location information is sent every 100 seconds and stops after deactivation is communicated. You must distinguish this communication from any call you may need to make to request assistance. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The cost of communications must be included in the price and guaranteed for at least 12 years. The operating and communication components must be inside the casing, without relying on an external mobile application. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The V-16 warns of the immobilised vehicle and transmits its location. You must request the assistance you need by appropriate means: transmitting this location is not the same as speaking to the emergency services and does not in itself guarantee that an ambulance is dispatched. You study the procedure for raising the alarm and protecting passengers in «Responding to accidents and breakdowns». [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).

23Positioning the V-16 on a minibus

A minibus towing a trailer is parked in a roadside bay, with an illuminated V-16 beacon on a bracket high on the driver’s door and its hazard lights on.
The key idea

Place your beacon where it is most visible without exposing yourself to traffic.

Remember

  • Place V-16 as high as possible, ensuring maximum visibility.
  • If you cannot reach the roof, use an accessible exterior surface and suitable mount.
  • Prepare and check its position with the minibus parked.
  • Use hazard lights and, where required, position lights and end-outline marker lamps.
  • If you cannot leave safely, stay inside with your seat belt fastened.
  • Do not improvise a climb onto the roof.

Exam trap: Wrong: you must always get out. Right: if you cannot resume driving and there is a safe place outside the carriageway and hard shoulders, leave on the side away from traffic. Do not remain on or walk along lanes or hard shoulders. If you cannot leave safely, stay inside with your seat belt fastened.

Read the full explanation
  • Place the V-16 as high as possible to ensure maximum visibility. If the height of the minibus prevents you from reaching the roof, you can attach a suitable device to the driver’s door or an accessible part of the side. You must choose the mount specified by the manufacturer for the vehicle surface. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16). [DGT, positioning the V-16](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).
  • Prepare for positioning the beacon while the minibus is parked: check where your beacon attaches and whether the bodywork or trailer obscures its light. The DGT provides for placing it at the rear of tall vehicles when you can leave the vehicle safely. If you cannot do so, use the highest accessible exterior part of the cab; do not improvise a way to climb onto the roof. [DGT, tall vehicles and buses or coaches](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).
  • When warning of an immobilisation due to an accident or breakdown, you must switch on the hazard warning lights and, where applicable, the position lights and end-outline marker lamps, as well as use the regulation device. If you remain on the carriageway or hard shoulder at night or in reduced visibility, keep the required lights on. [RGC, art. 130.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130). [RGC, art. 105.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a105).
  • If you cannot resume your journey and there is a safe place beyond the carriageway and hard shoulder, you must leave the vehicle on the side away from traffic, without remaining in or walking along traffic lanes or hard shoulders. If you cannot get out safely, you must remain inside with your seat belt fastened; the full procedure is covered in «Responding to accidents and breakdowns». [RGC, art. 130.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130).

24High-visibility vest

A driver wearing a high visibility vest stands on the step of the right-hand door of an orange minibus with a trailer, stopped beside an interurban road during the day.
The key idea

Wear your vest when outside on an interurban road’s carriageway or hard shoulder.

Remember

  • Carry a regulatory reflective high-visibility vest in your non-special combination.
  • Keep it accessible so you can put it on before getting out.
  • Wear it when getting out to check a light or connection too.
  • The requirement applies without an accident and during daylight too.
  • Keep its strips and fabric in good condition.
  • Keep seeking a safe place and avoid exposure to traffic.

Exam trap: Wrong: your vest allows you to stay on the hard shoulder. Right: it makes you visible, but you must avoid exposure to traffic.

Read the full explanation
  • You must carry a high-visibility reflective vest as part of the equipment for a non-special vehicle combination. It must meet the regulatory requirements for personal protective equipment; you must not replace it with a light-coloured garment or any clothing with a small reflective strip. [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • As the driver of a bus or coach or a non-agricultural vehicle combination, you must put on the vest when you leave the vehicle and enter the carriageway or hard shoulder of an interurban road. This obligation also applies if you get out to check a connection or a light; it does not depend on an accident having occurred or on it being night-time. [RGC, art. 118.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a118).
  • As a preparation guideline, keep the vest accessible in the cab so that you can put it on before getting out. Keep its strips and fabric in good condition. Keeping it in a compartment that you can only reach by walking along the hard shoulder makes it harder to obtain the very protection you need when leaving the vehicle.
  • The vest improves your visibility, but you must continue to avoid exposure to traffic. It does not authorise you to stay beside the trailer on the hard shoulder or cross traffic lanes to check its lights. You must also apply the breakdown rules for leaving the vehicle and remaining in a safe place. [RGC, art. 130.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130).

25Fire extinguisher for the minibus and trailer

A green minibus with a trailer is stopped beside the right-hand kerb, with a fire extinguisher secured in a bracket beside the steps of the open door.
The key idea

Choose your extinguisher by the minibus’s total seats, not the passengers present.

9 seatsRange starts above this
23 seatsMaximum, including the driver
8A/34BMinimum extinguisher rating

Remember

  • Carry suitable, type-approved equipment ready for use.
  • Count the driver’s seat and passenger seats.
  • Above 9 and up to 23 total seats, carry one 8A/34B extinguisher.
  • Do not choose by powder weight: check the certified rating.
  • Check attachment, access, condition, seal and service indicators.
  • Find your extinguisher and read its instructions without blocking exits.

Exam trap: Wrong: towing means you use the goods vehicle scale based on MMA. Right: for your minibus, count total seats, including the driver.

Read the full explanation
  • You must carry suitable, type-approved fire-extinguishing equipment in working order: Annex XII requires it for buses and coaches and for non-special vehicle combinations. It is part of the compulsory equipment for your minibus with a trailer, regardless of whether you carry dangerous goods or whether the vehicle is full of passengers. [RGV (General Vehicle Regulations), Annex XII.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • For a passenger vehicle with more than 9 and up to 23 seats, including the driver's seat, the general minimum requirement is one fire extinguisher with an 8A/34B fire rating. Your extinguishers must comply with this table and undergo their periodic inspections. You must use the vehicle's seating capacity, including the driver's seat. [Order of 27 July 1999, second.a](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#segundo).
  • The trailer does not turn your passenger vehicle into a goods vehicle combination to which you automatically apply the scale of extinguisher requirements based on MMA (maximum authorised mass). Read the certified fire rating: the quantity of powder in kilograms does not, on its own, demonstrate that rating. [Order of 27 July 1999, second](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#segundo).
  • Your extinguishers must be portable and manually operated, with an extinguishing agent suitable for the vehicle, preferably dry powder or another suitable agent. You must check them regularly and have them undergo, as a minimum, the operations in Table II of Annex II to the Reglamento de instalaciones de protección contra incendios (Fire Protection Installations Regulations), to which the order refers. As part of your checks as the driver, check their mounting, accessibility, condition, seal and service indicators. [Order of 27 July 1999, first](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#primero).
  • Position and keep your extinguisher so that you can find and remove it without unloading the luggage or blocking the passengers' exit, following the vehicle's instructions. Knowing where it is and reading its instructions form part of your practical preparation; you learn about using it in a fire and evacuation in «Responding to accidents and breakdowns».

Checking the signalling on the towed vehicle

Check each function with the combination secured against movement and the connections secured.

  1. Check the electrical connection and inspect the condition of the lights, reflectors, plates and contour marking strips.
  2. Switch on the position lights and also check the number plate lighting, end-outline marker lamps and side marker lamps where applicable.
  3. Operate each indicator and then the hazard warning lights; check the rear end of the combination.
  4. Check the brake lights, rear fog light and any fitted reversing lights with safe assistance.
  5. Rectify faults and remove anything that obscures the signalling before driving.

Securing the combination on a slope

Apply the measures in article 92.3 and check that the combination is secured against movement.

  1. Secure the combination against movement and apply the parking brake.
  2. When leaving the driving seat, stop the engine, switch off the ignition and select first gear uphill, reverse downhill or park, depending on the transmission.
  3. On a significant gradient, use suitable chocks or rest a steered wheel against a kerb as prescribed by the regulations.
  4. If you use a kerb, turn the wheels towards the centre of the road uphill and outwards downhill.
  5. Check that the combination is secure; when moving off again, remove the chocks from the road and stow them.

Using the V-16 from the cab

Warn others that the combination is immobilised without exposing yourself to traffic.

  1. Secure the combination against movement and use the hazard warning lights and any other appropriate lights.
  2. Take the connected V-16 from its accessible storage location and activate it according to its instructions.
  3. Place it as high as possible with maximum visibility; if the height of the minibus prevents you from reaching the roof, use an accessible point on the side and a suitable fastening.
  4. Put on your high-visibility vest before getting out if you are going to be on the carriageway or arcén (hard shoulder) outside built-up areas.
  5. Only get out if there is a safe place away from the carriageway and hard shoulder; otherwise, remain inside with your seat belt fastened.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1In a test for the D1+E and D+E licences, the examiner may check that the applicant is wearing:
2Before leaving with a D+E combination, the driver should especially check:
3Before setting off with a D+E combination, which check directly concerns the connection between the bus and trailer?
4In a D+E combination, before departure you must check that the electrical and, where applicable, air connections:

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module