Theory · A2 Licence - Motorcycle · Module 17 of 18

Preventive and efficient motorcycle riding

You learn to observe, anticipate and preserve space to respond to unexpected situations on your motorcycle. You learn to reduce fuel consumption and noise through smooth riding, choose the right gear and tyre pressure, and interpret environmental badges and ZBE (low-emission zone) restrictions. For the exam, you distinguish legal obligations from efficiency advice and avoid applying criteria for cars to motorcycles.

24 min read17 sectionsReviewed Nov 2, 2026
A motorcyclist wearing protective gear rides in the right lane and keeps a wide gap behind the car ahead on a Mediterranean road.
Anticipation and space for smooth riding

1Prevention means preparing your response

A helmeted motorcyclist travels in their lane and maintains a large gap behind two cars forming a traffic queue on a road in a Mediterranean setting.
The key idea

Watch and leave space so you can respond before danger develops.

Remember

  • Keep watching throughout your journey, even on familiar streets.
  • Think about what could happen before you act.
  • Leave space so you can respond smoothly.
  • Avoid accelerating if you will soon need to brake.
  • Remember that other drivers may not see you.

Exam trap: Wrong: your experience prevents every surprise. Right: keep watching and leaving space throughout your journey.

Read the full explanation
  • Preventive riding means gathering information and keeping a margin to respond before a situation becomes critical. You must do this throughout your journey, including on familiar streets with little traffic. Experience helps you interpret what you observe, but it does not allow you to predict every movement other people make.
  • Use observation, anticipation and space: observe your surroundings, anticipate what may happen and leave enough space to act. If you spot a queue but keep accelerating until you reach it, you waste that information. If you see a hazard but ride too close, you may lack the margin to avoid it.
  • On a motorcycle, you need to consider your balance and the fact that you are less visible to other drivers. You must not rely on agility or acceleration to make up for poor preparation. An early, smooth decision usually demands less grip than an urgent correction of speed or course.
  • Efficient riding shares this preparation: avoiding acceleration that you soon have to undo reduces unnecessary effort. You can ride smoothly without riding fast. You must consider the overall result of your decisions, including whether an apparent time saving makes you brake immediately afterwards.

2Preparing your route

A helmeted motorcyclist sets the navigator on a motorcycle parked in a layby separated from the road, in a Mediterranean landscape.
The key idea

Plan your route to avoid rushing and unexpected decisions.

RouteWhat you should consider
Short, with many stopsMay demand more attention and use more energy
With free-flowing trafficMay be more efficient

Remember

  • Check traffic, roadworks and weather before you leave.
  • Set your navigation device while stopped somewhere safe where stopping is allowed.
  • Plan alternatives in case access is restricted.
  • Allow extra fuel or energy for possible diversions.
  • Plan breaks and avoid arrival times that pressure you to speed.
  • Before visiting a ZBE, check its access rules.

Exam trap: Wrong: your displayed range is guaranteed. Right: wind, hills, load and pace can change it.

Read the full explanation
  • Before setting off, check your route, traffic, roadworks and the weather forecast. Choose a route suited to your experience and the characteristics of your motorcycle, rather than considering distance alone. A short route with many stops may be less efficient and demand more attention than one with free-flowing traffic. Specific road surface and weather risks are covered in the Motorcycle risks and prevention module.
  • Set up your navigation device with the motorcycle stopped somewhere safe where stopping is permitted. Decide in advance on important turn-offs, your arrival point and alternatives if you encounter restricted access. This avoids having to make a decision while attending to pedestrians, vehicles and your balance at the same time.
  • Calculate your available fuel or energy with a margin for diversions and queues, without deliberately using up your entire range. The dashboard display is an aid: wind, gradients, load and pace can change how far you can travel. You must not treat the stated range as a guaranteed distance in all conditions.
  • Plan your breaks and avoid an arrival time that puts pressure on you to speed. If your destination is within a ZBE, check access before setting off. Environmental and preventive preparation complement each other: a planned alternative avoids unnecessary detours and improvised manoeuvres near the entrance.

3Looking ahead and checking nearby

A motorcyclist rides in the right lane toward a bend, with their head facing the road ahead and a utility cover and stones visible on the nearby road surface.
The key idea

Alternate between looking ahead, checking nearby and glancing briefly in your mirrors.

Remember

  • Look where you are going and check the nearby road surface too.
  • On bends, look for the exit without neglecting your lane.
  • Increase your gap if a vehicle blocks your view ahead.
  • Check both sides at junctions, garage entrances and parking areas.
  • Check your mirrors briefly and often, including before slowing down.

Exam trap: Wrong: following another vehicle guarantees a clear path. Right: check the road ahead yourself.

Read the full explanation
  • Look along the route you intend to follow and alternate this with checks of the area close to you. Looking only at your front wheel makes you spot bends, queues and sideways movements too late. Looking only at the horizon can also make you miss dirt or a nearby inspection cover.
  • On a bend, look for information about the road ahead and the exit without losing sight of your lane and the road surface. If a van blocks your view of the road, increase your margin to regain visibility. Do not take the movement of the vehicle ahead as proof that your path remains clear.
  • Check both sides at junctions, garage entrances and areas with parked vehicles. A car’s wheels, an occupant beside a door or a partly hidden pedestrian provide clues to possible movements. You must interpret these as possibilities to prepare your response, without assuming what each person is going to do.
  • Check your mirrors with brief, repeated glances, including when you are not about to manoeuvre. You must know whether someone is approaching from behind before slowing down. Spread your attention: looking in a mirror for too long can make you miss changes in the traffic ahead. [DGT, preventive driving](https://www.dgt.es/muevete-con-seguridad/conviertete-en-un-buen-conductor/consejos-generales/conduccion-preventiva/).

4Blind spots and seeing each other

A motorcyclist travels in the right lane and looks over their left shoulder while a car approaches head-on in the opposite lane.
The key idea

Check areas your mirrors cannot show before moving sideways.

Remember

  • Adjust your mirrors before you set off.
  • Remember that unseen areas may remain: these are blind spots.
  • Check those areas directly when necessary and safe, while keeping control.
  • Avoid looking away from the road ahead for too long.
  • Avoid staying where other drivers cannot see you well.
  • Read your manual to understand the limits of electronic aids.

Exam trap: Wrong: no detector warning means you can move. Right: look and check that moving is safe.

Read the full explanation
  • Adjust your mirrors before moving off. Even when correctly aligned, they may leave areas outside both your direct view and your reflected view. Before moving sideways, supplement the information with a brief direct check when necessary and safe, maintaining control and avoiding taking your attention away from the road ahead for too long.
  • A convex mirror widens your field of view, but may make vehicles look smaller and apparently further away. You must bear this in mind when judging their approach. A vehicle taking up little space in the mirror does not prove that it is far away or that you have enough time to move into its path.
  • Avoid remaining in areas that other drivers cannot see well; the visibility limitations of large vehicles are covered in the Motorcycle risks and prevention module.
  • If your motorcycle has a system for detecting nearby vehicles, read the manual to understand how it works and its limitations. A warning may help, but the absence of a warning does not confirm that the space is clear. Electronics do not replace observation, checking blind spots or deciding whether you can move safely.

5Anticipating other people’s movements

A motorcyclist keeps a generous distance behind a truck signalling a right turn on an urban street.
The key idea

Prepare for other people's movements, even when you have priority.

Remember

  • Watch for hidden pedestrians and vehicles that may pull out.
  • Leave large vehicles enough space to turn.
  • Slow down if someone seems not to have seen you.
  • Prepare your controls without causing unwanted braking.
  • Avoid sudden changes that surprise others.

Exam trap: Wrong: an indicator guarantees the vehicle will turn. Right: wait until the situation is actually safe.

Read the full explanation
  • In towns, identify areas of uncertainty: a pedestrian between cars, a vehicle leaving a parking space or a stationary bus may lead to movements that are difficult to see. Reduce the demands of your riding in good time. Do not wait for confirmation that someone is entering your path before starting to create a margin.
  • Keep clear of the space a large vehicle needs to turn; its specific risks are covered in the Motorcycle risks and prevention module.
  • Even when you have priority, be prepared if another road user seems not to have seen you. Your preventive aim is to avoid conflict, rather than prove your priority by arriving first. You can moderate your speed and prepare the controls to respond, without operating them abruptly or keeping pressure on them that causes unintentional braking.
  • Make your own decisions easy to understand: avoid sudden changes of pace, prepare your movements in good time and check how your surroundings are changing. Another vehicle’s indicator signals an intention, but does not prove that the vehicle is going to complete the turn. Wait until the situation is actually safe before acting.

6Space to react

A helmeted motorcyclist follows an orange car with a wide clear gap between them on a rural road.
The key idea

Leave enough space to stop if the vehicle ahead brakes suddenly.

two secondsRecommended minimum gap
three or more secondsBad weather or wet tarmac
ConditionsDGT recommended gap
NormalAt least two seconds
Bad weather or wet tarmacThree seconds or more
Poorer visibility, grip or responseIncrease your gap if needed

Remember

  • Adjust your gap for your speed, grip and brakes.
  • Use a fixed point to estimate your time gap.
  • If you reach it too soon, increase your gap smoothly.
  • Leave sideways space beside pedestrians and parked cars.
  • When stopping in a queue, leave space and watch behind you.

Exam trap: Wrong: the recommended time gap always suffices. Right: increase your gap when conditions require it.

Read the full explanation
  • You must leave enough space to stop if the vehicle ahead brakes suddenly, taking account of speed, grip and braking. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54). The gap also lets you see more of the road and start slowing progressively, instead of copying each change by the vehicle ahead with a delay.
  • The DGT recommends a gap of at least two seconds behind the vehicle ahead, increasing it to three or more in bad weather or on wet tarmac. Increase this margin if visibility, grip or your ability to respond requires it: it is preventive guidance, not a universal guarantee. [DGT, preventive driving](https://www.dgt.es/muevete-con-seguridad/conviertete-en-un-buen-conductor/consejos-generales/conduccion-preventiva/).
  • To estimate the interval, choose a fixed reference point and count from when the vehicle ahead passes it until you reach it. If you reach the reference point too soon, restore the gap smoothly. Do not calculate the distance by continually looking at a stopwatch or the dashboard: the check must allow you to keep paying attention to traffic.
  • Keep a sideways margin beside parked cars, pedestrians and large vehicles. An apparently empty space may cease to be clear if a door opens or a vehicle changes course. When stopping in a queue, leave a useful gap and watch behind you; you do not need to put your wheel right up against the vehicle ahead to make use of the space.

7If someone follows too closely

A motorcyclist rides in the right-hand lane with a large gap to the car ahead while another car follows very closely on a rural road.
The key idea

If someone follows too closely, gently increase your gap behind the vehicle ahead.

Remember

  • Prepare changes of speed early.
  • Glance briefly behind without neglecting the road ahead.
  • Do not brake to frighten the person following you.
  • Do not speed because another driver pressures you.
  • Let them pass only when you can do so safely and lawfully.
  • Use an escape route only if clear and safe to reach.

Exam trap: Wrong: moving closer to the vehicle ahead protects you. Right: gently increase your gap to brake progressively.

Read the full explanation
  • Gently increase your gap behind the vehicle ahead. This allows you to respond more progressively to a reduction in speed and helps the person following you notice the manoeuvre. Moving closer to the vehicle ahead to prevent someone from filling the gap reduces your ability to respond and may increase the risk of a rear-end collision.
  • Monitor the situation behind with brief mirror checks, without focusing all your attention there. Prepare your changes of speed in good time. If you need to brake, do so according to the situation and with the appropriate braking system; do not brake to punish or frighten the person behind.
  • Do not increase your speed because of pressure from another driver. If there is a safe, lawful opportunity to let them continue on their way, you can take it without putting yourself at risk. The aim is to regain a margin, rather than compete for a position or try to pull away through excessive acceleration.
  • When you spot a queue, start slowing down early and watch how traffic behind is approaching. An escape route is only useful if it is actually clear and you can reach it safely. Do not assume that a motorcycle’s narrow width allows you to get out of any situation between vehicles.

8A smooth pace, starting and waiting

A motorcyclist wearing a helmet and protective gear approaches a red traffic light on a green motorcycle, with clear space before the stop line.
The key idea

Ride smoothly and adjust your speed to the distance you can see.

Remember

  • Avoid accelerating towards a stop you can foresee.
  • Ride so you can stop within the distance you can see.
  • Start your engine and move off as your manual instructs.
  • Avoid strong acceleration while your engine is cold.
  • Use automatic engine stopping as instructed, keeping your balance and ability to respond.
  • Switch off your engine when refuelling.

Exam trap: Wrong: riding at the speed limit is always safe. Right: slow further when visibility, load or grip requires it.

Read the full explanation
  • Use the throttle progressively and avoid accelerating towards a foreseeable stop. A smooth pace reduces unnecessary acceleration back up to speed and abrupt changes in the load on the tyres.
  • Adjust your speed so that you can stop within the distance you can see and before foreseeable obstacles. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45). A speed within the limit may still be excessive for your visibility, load or grip; efficiency does not turn the limit into a speed you must reach.
  • Start the engine according to the manual and move off gently when the manufacturer allows it. Avoid blipping the throttle and prolonged warming up at idle; do not demand strong acceleration while the engine is cold.
  • An idling combustion engine consumes fuel even while the motorcycle is stationary. If it has an automatic stop system, use it according to its operating conditions, without compromising stability or your ability to respond.
  • You must switch off the engine when refuelling. [RGC, art. 115](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a115).

9Gears, engine speed and engine braking

A motorcyclist wearing a helmet and protective clothing rides a green motorcycle downhill in the right-hand lane, with both hands on the handlebars and the clutch lever released.
The key idea

Choose a gear that lets you ride smoothly and respond when needed.

Motorcycle transmissionWhat you should do
Manual gearsChoose a gear giving smooth progress and enough power
Scooter with continuously variable transmissionControl the throttle and follow your manual

Remember

  • Change down if your engine judders or lacks power.
  • With a passenger or uphill, you may need a lower gear.
  • Ease off the throttle early to use engine braking.
  • On descents, avoid neutral and holding the clutch in.
  • Do not switch off your engine while moving.
  • Avoid sudden downshifts.

Exam trap: Wrong: closing the throttle always stops fuel consumption. Right: this depends on your engine, its speed and how it works.

Read the full explanation
  • Choose a gear that allows smooth progress and sufficient response, without keeping engine speed unnecessarily high. If too high a gear causes juddering or a lack of power, change down; there is no single gear-change engine speed that applies to all A2 motorcycles.
  • With a passenger or on an uphill gradient, you may need a lower gear. On a scooter with a continuously variable transmission, regulate demand with the throttle and follow the instructions for its automatic transmission.
  • Ease off the throttle in good time when you need to slow down, and use engine braking in an appropriate gear. On descents, avoid neutral and holding the clutch in: you lose that assistance and place greater demands on the brakes. Do not switch off the engine while moving.
  • Avoid abrupt downshifts that affect rear-wheel grip; braking and downshifting techniques are covered in the Motorcycle riding techniques module.
  • On fuel-injected engines, the fuel supply may be cut during certain periods of engine braking, depending on engine speed and electronic management. Do not assume zero consumption whenever you close the throttle: a carburettor, engine speed close to idle or a different engine strategy may produce a different result. The vehicle manual determines how it operates.

10Speed, aerodynamics and load

A rider wearing a full-face helmet and fitted protective gear travels to the right on a motorcycle without luggage in the near lane of a Mediterranean rural road.
The key idea

Moderate your speed and avoid unnecessary weight to use less energy.

Remember

  • Do not ride close behind another vehicle for shelter from the air.
  • Keep a clear view and access to controls whatever your posture.
  • Wear protective clothing that fits well.
  • Remove unnecessary weight and accessories only when your manufacturer allows it.
  • Remember that even empty panniers can increase air resistance.
  • With passengers or luggage, follow manufacturer adjustments; see “Passengers and loads on motorcycles”.

Exam trap: Wrong: a fairing guarantees savings and stability in any wind. Right: this depends on design and conditions.

Read the full explanation
  • As speed increases, air resistance rises and the energy needed per kilometre usually increases. Maintain a moderate pace suited to the route; do not move close to another vehicle to take advantage of its slipstream.
  • The fairing and a tucked-in posture may reduce aerodynamic drag, depending on the motorcycle’s design. Maintain your view and access to the controls: neither a fairing nor low handlebars guarantee savings or stability in every wind condition.
  • Wear well-fitting protective equipment. Flapping clothing increases discomfort and may increase air resistance; do not reduce your protection to save fuel or energy.
  • Remove unnecessary weight and accessories when the manufacturer allows it: mass requires energy when accelerating and climbing, and panniers or a top box may increase air resistance even when empty.
  • With a passenger and luggage, make the adjustments specified by the manufacturer; load distribution, securing and limits are covered in “Passengers and loads on motorcycles”.

11Tyre pressure and maintenance for efficiency

A crouching person checks the front tyre pressure of a motorcycle parked in a house driveway using a pressure gauge.
The key idea

Check tyre pressures when cold and maintain your motorcycle as your manufacturer instructs.

Remember

  • Use the specified pressure for each wheel and load.
  • Check pressures often and before long journeys.
  • Do not overinflate to save energy or arbitrarily deflate tyres for grip.
  • Fix repeated pressure loss.
  • Follow maintenance instructions and use the specified fuels and lubricants.
  • Check your motorcycle if consumption rises without a clear reason.

Exam trap: Wrong: much higher pressure saves energy without risks. Right: use your manufacturer's specified pressures.

Read the full explanation
  • Measure tyre pressures when cold and use the manufacturer’s values for each wheel and load. Check them frequently and before a long journey: incorrect pressure compromises grip. [DGT, motorcycling](https://www.dgt.es/muevete-con-seguridad/viaja-seguro/en-moto/).
  • Underinflation may increase rolling resistance, fuel or energy consumption, heat build-up and wear. Do not overinflate to save fuel or energy, or arbitrarily deflate tyres to seek more grip; rectify repeated pressure loss.
  • Follow your motorcycle’s maintenance requirements and fuel and lubricant specifications. Maintain the transmission according to its type; a chain needs the prescribed adjustment and lubrication. Specific procedures are covered in the Motorcycle mechanics and maintenance module.
  • If consumption rises for reasons that traffic, route, load or weather do not explain, check the motorcycle’s condition. Do not make a diagnosis from a single piece of information or ignore leaks, juddering or abnormal noises.

12Savings and emissions

A rider wearing a helmet and protective clothing rides a green electric motorcycle in the right-hand lane of a Mediterranean rural road.
The key idea

Compare consumption in similar conditions and check what your Eco mode does.

Remember

  • Compare similar journeys, allowing for traffic, load and weather.
  • Do not expect fixed savings from smooth riding.
  • Check your manual for when to use Eco mode.
  • Speed, tyre pressure, weight and air resistance also affect your electric motorcycle.
  • Distinguish energy use, exhaust gases and noise.

Exam trap: Wrong: Eco mode gives you an ECO badge. Right: it does not determine your environmental classification.

Read the full explanation
  • You can compare consumption on similar journeys, taking account of traffic, load and weather. There is no fixed percentage saving from riding smoothly or changing up earlier.
  • If your motorcycle has Eco mode, check what it changes and when it is appropriate to use it. Its effect depends on the model and your riding; it does not guarantee a fixed saving or determine the environmental badge.
  • On an electric motorcycle, smoothness, speed, pressure, weight and aerodynamics also have an effect. Energy used, exhaust pollutants and noise are separate aspects: reducing one does not, on its own, establish an environmental classification.

13What the environmental badge identifies

A helmeted person beside a parked motorcycle holds a screen with four circular samples: blue, green and blue, green, and yellow.
The key idea

Use your registration number to check your motorcycle's recorded environmental classification.

40 kmPlug-in electric range: NEDC threshold
BadgeColourCriteria for L-category motorcycles
BYellowEuro 2
CGreenThe Annex lists Euro 3 and Euro 4
ECOGreen and blueNon-plug-in hybrid; plug-in hybrid with electric range below 40 km NEDC
0 emisionesBlueBattery-electric, range-extended electric, hydrogen, fuel-cell; plug-in hybrid with electric range at least 40 km NEDC
A, no badgeNo stickerCheck your motorcycle's recorded category

Remember

  • Recognise V-25 as the environmental badge.
  • Do not confuse environmental category A with the category A driving licence.
  • Check your recorded category: do not deduce it from the Euro standard alone.
  • Do not classify your motorcycle using registration dates for cars.
  • Do not deduce your badge from engine size, consumption or licence requirements.
  • Remember that Eco mode does not mean ECO classification.

Exam trap: Wrong: you classify your motorcycle by registration date like a car. Right: check its recorded classification.

Read the full explanation
  • The environmental classification appears in the Registro de Vehículos (Vehicle Register), and the badge identifying it is sign V-25. The badges are 0 emisiones (zero emissions), ECO, C and B; category A has no badge. [RGV, Annex XI, V-25](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxi). Recognise 0 by its blue background, ECO by green and blue, C by green and B by yellow. Do not confuse this category A with the category A driving licence.
  • For your motorcycle, within category L, Annex II lists B for Euro 2 and C for Euro 3 and Euro 4. It does not expressly list Euro 5 or Euro 5+: check the category recorded for your motorcycle in the Registro de Vehículos, without deducing it from the Euro standard yourself. [RGV, Annex II.E](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anii).
  • For L-category vehicles, ECO covers non-plug-in hybrids and plug-in hybrids with an electric range of less than 40 km on the NEDC cycle. The 0 emisiones category includes battery-electric, range-extended electric, hydrogen and fuel-cell vehicles, and plug-in hybrids with at least 40 km on that cycle. [RGV, Annex II](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anii).
  • Use your registration number to check your motorcycle’s recorded classification through the DGT service. Engine capacity, the licence required, consumption and indicative registration dates for cars do not determine a motorcycle’s badge. Eco mode does not equate to the ECO classification either. [DGT, badge check](https://www.dgt.es/nuestros-servicios/tu-vehiculo/tus-vehiculos/distintivo-ambiental/).

14Displaying the badge and what it means

A motorcycle parked with the kerb on its right displays a green environmental sticker on a side panel, without covering the windscreen or controls.
The key idea

Check whether you must display the sticker and place it where it is visible.

BadgeWhat it identifies
V-25Environmental classification
V-26Shared use

Remember

  • Check whether local rules require you to display the badge.
  • Display it visibly without blocking your view or affecting motorcycle parts.
  • Using another category's sticker does not change your recorded classification.
  • Do not assume sharing or renting a motorcycle allows unrestricted access.

Exam trap: Wrong: displaying the sticker is never compulsory. Right: it is generally voluntary, but the authority may require it.

Read the full explanation
  • Displaying the badge is generally voluntary; the competent authority may expressly require it in its regulations. Check whether it is compulsory where you intend to ride. [RGV, Annex XI, V-25](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxi).
  • On a motorcycle, place the badge somewhere visible, without impairing your view or the operation of its components. [DGT, displaying the badge](https://www.dgt.es/nuestros-servicios/tu-vehiculo/tus-vehiculos/distintivo-ambiental/).
  • The sticker identifies the classification recorded in the Registro de Vehículos; placing a badge from another category on the motorcycle does not change its registered details. [RGV, Annex XI, V-25](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxi).
  • Do not confuse environmental badge V-25 with shared-use badge V-26. [RGV, Annex XI](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxi). Renting or sharing a motorcycle may be a mobility option, but it does not replace its environmental classification or the conditions governing restricted access.

15Low-emission zones

A helmeted motorcyclist checks a phone while seated on a motorcycle parked beside the kerb, before an urban entrance marked with an emissions restriction sign.
The key idea

Before entering a ZBE, check the local access rules for your motorcycle.

Remember

  • Check the zone boundary and local rules.
  • Check the specific conditions for motorcycles.
  • Check whether you need permission, registration or proof of an exception.
  • Check operating times and temporary pollution restrictions.
  • Check parking rules too.
  • If you cannot meet the conditions, plan another route or use other transport.

Exam trap: Wrong: any badge lets you enter any ZBE. Right: your motorcycle must meet the local conditions.

Read the full explanation
  • A ZBE is a defined area where access, traffic and parking are restricted to improve air quality and reduce emissions affecting the climate. Its specific regulation is the responsibility of the local authority. [RD 1052/2022, art. 2](https://www.boe.es/buscar/act.php?id=BOE-A-2022-22689#a2). You must check the regulations of your destination municipality and the boundary within which they apply.
  • The measures are based on environmental classification and must favour less polluting vehicles. [RD 1052/2022, art. 5](https://www.boe.es/buscar/act.php?id=BOE-A-2022-22689#a5). Having a badge does not give you universal permission to enter: conditions may vary for different categories, times, uses and authorised circumstances.
  • Motorcycles may be affected: you are not exempt because you take up little space or use a motorcycle covered by an A2 licence. Before travelling, check whether you need authorisation, registration or proof that a specified exception applies. Check the specific conditions for motorcycles in the municipal regulations. [RD 1052/2022, arts. 2 and 5](https://www.boe.es/buscar/act.php?id=BOE-A-2022-22689#a5).
  • Also check temporary pollution restrictions and parking conditions at your destination. Authorisation to enter does not automatically mean unrestricted parking. If you cannot meet the conditions, prepare an alternative outside the area or use another means of transport; do not look for an unsigned street to evade the boundary.

16Recognising sign R-120

A helmeted motorcyclist approaches an R-120 sign with a supplementary panel without text in their lane on a road in a Mediterranean landscape.
The key idea

Read sign R-120 together with the text explaining its restriction.

Remember

  • Read the S-860 plate or signboard accompanying the sign.
  • Check whether your motorcycle meets the environmental criteria shown.
  • Check local access rules too.
  • If you notice the restriction late, avoid sudden braking or turning.
  • Follow a permitted alternative and check information somewhere safe where stopping is allowed.

Exam trap: Wrong: the car picture excludes motorcycles. Right: R-120 applies according to the criteria shown.

Read the full explanation
  • Sign R-120 prohibits entry to vehicles according to their environmental badge or other environmental criteria. Its conditions are shown on an S-860 supplementary plate or on a signboard incorporating the sign. You must interpret the sign and its text together. [RD 465/2025, Annex I catalogue, R-120](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Do not conclude from the picture of a car that the restriction only affects cars. The meaning of R-120 refers to vehicles according to the stated criteria. Compare your motorcycle’s classification with the specific access information and the local regulations you have checked.
  • If you discover the restriction as you approach, do not stop abruptly or improvise a dangerous turn. Follow a lawful alternative and find somewhere you are allowed to stop to check the information. Planning ahead and observing signs early allow you to decide in good time, without encroaching on other spaces or surprising other road users.

17Noise and an effective exhaust system

A motorcyclist wearing a helmet and protective clothing rides to the right within their lane on a green motorcycle with a complete silencer and no visible damage.
The key idea

Keep your exhaust working properly and use your horn only when allowed.

SituationHorn use
Possible accidentYou may warn others, including in built-up areas
Announcing an overtakeYou may warn others outside built-up areas
Exceptional urgent service requiring you to warn othersSound your horn intermittently; see “Priority of passage”, section “Emergency in a private vehicle”, for conditions.
Impatience or warning without reasonYou must not use it

Remember

  • Do not ride with an unsilenced exhaust or an ineffective silencer.
  • Avoid unnecessary bursts of acceleration and running your engine without reason.
  • Do not rely on a loud exhaust to make others notice you.
  • Use your horn only exceptionally and without excessive noise.
  • You may replace permitted warnings with brief light flashes without dazzling anyone.
  • Officers may immobilise your motorcycle if gases, smoke or noise exceed legal limits.

Exam trap: Wrong: you may sound your horn in town solely to announce an overtake. Right: that warning is allowed outside built-up areas. Officers may immobilise your motorcycle for excess gases, smoke or noise [Ley de Tráfico (Traffic Act), art. 104.1.h].

Read the full explanation
  • You must not ride with an unsilenced exhaust or an incomplete, unsuitable or damaged silencer that is ineffective. The prohibition applies on urban and interurban roads. [RGC, art. 7](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a7). Maintain the exhaust and its components in accordance with your motorcycle’s technical requirements.
  • Avoid unnecessary bursts of acceleration, unnecessarily high engine speeds and running the engine at idle without reason. These practices cause nuisance and may increase consumption. A louder exhaust does not replace observation or provide a reliable way of making others notice you at a junction or in another vehicle’s blind spot.
  • You may use the horn to avoid a possible accident, especially on narrow roads with many bends, and, outside built-up areas, to warn a driver you intend to overtake. Its use must be exceptional, with a non-shrill sound, and using it without reason or excessively is prohibited. [RGC, art. 110.1 and 2.a-b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a110).
  • If an exceptional urgent service requires you to warn others of your situation, sound the horn intermittently ([RGC, art. 110.2.c](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a110)); the conditions are covered in “Priority of passage”, in the “Emergency in a private vehicle” section.
  • You may replace these warnings with brief flashes of dipped beam, main beam or both alternately, including in built-up areas, avoiding dazzling others. [RGC, art. 109.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).
  • Officers may immobilise your motorcycle if it exceeds the regulatory levels for gases, smoke or noise. [Ley de Tráfico (Traffic Act), art. 104.1.h](https://www.boe.es/buscar/act.php?id=BOE-A-2015-11722#a104).

Observe and prepare a response

Turn information from your surroundings into a safety margin.

  1. Check far ahead, nearby and on both sides; glance briefly in your mirrors.
  2. Identify which road user or obstacle may enter your path.
  3. Check the available space and ease your speed in good time.
  4. Prepare a smooth response and keep observing as the situation develops.
  5. Act according to the actual risk, without relying solely on your priority or on others having seen you.

Prepare an efficient motorcycle

Adjust the motorcycle and its equipment to the route and actual load.

  1. Check the route, traffic, weather and environmental restrictions at your destination.
  2. Check the manufacturer’s specified pressures for each wheel and load when the tyres are cold.
  3. Remove unnecessary weight and accessories when the manufacturer allows it.
  4. Distribute and secure luggage and make the adjustments specified for a passenger or load.
  5. Check maintenance and range; move off gently and use an appropriate gear.

Slow down without wasting energy

Anticipate a stop without losing control.

  1. Spot traffic lights, queues, bends or other reasons to slow down in good time.
  2. Check the situation behind with a brief glance.
  3. Ease off the throttle early and keep an appropriate gear engaged.
  4. Combine engine braking and progressive braking as needed, without abrupt downshifts.
  5. Stop if necessary and maintain space, stability and awareness of your surroundings.

Check access to a ZBE

Link classification, signs and local authorisation.

  1. Check your motorcycle’s environmental classification using its registration number.
  2. Check the boundary, current conditions and specific rules for motorcycles.
  3. Check whether you need a visible badge, registration or authorisation, and meet those requirements.
  4. Read R-120 together with its plate or signboard and check that you are allowed to enter.
  5. If access is not authorised, use a lawful alternative prepared in advance.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module