Theory · C1 Licence - Light Truck · Module 10 of 18

Dimensions and masses of the light lorry

You learn to calculate the masses and dimensions of your C1 lorry and interpret the general tables, load overhangs and access restrictions. You can answer questions on axles, vehicle combinations, special transport and speed limiters without confusing the vehicle's maximum limits with your licence entitlement.

40 min read27 sectionsReviewed Nov 3, 2026
A two-axle light truck carries boxes secured with straps in the right-hand lane of a Mediterranean rural road.
Light truck dimensions, masses and load

1Which mass you are calculating

A light truck with the driver on the left side of the cab and secured crates in the load bed stands on a vehicle weighbridge.
The key idea

Distinguish tare from the actual weight of your loaded lorry.

75 kgStandard driver in running order
1,000 kgOne tonne
MassWhat you count
TareEquipped lorry, without people or goods
LadenActual lorry and everything it carries
Running orderTare plus 75 kg standard driver

Remember

  • Count the lorry, people and goods to find its laden mass.
  • Tare includes equipment and fluids, but excludes people and goods.
  • For actual mass, use the driver’s actual weight.

Exam trap: Wrong: Counting only the goods. Right: Count the lorry and everyone on board too.

Read the full explanation
  • The tare mass includes the authorised fixed equipment and full supplies of water, fuel, lubricants, spare parts, tools and necessary accessories, but excludes service personnel, passengers and goods. This means that a lorry without goods but with a driver does not have exactly the same mass as its tare mass. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The laden mass is the actual mass of the vehicle and everything it carries at that moment, including the people on board. To answer a weighbridge question, you must count the lorry, the goods, the driver and any other occupants actually present; do not use only the weight shown on the delivery note for the goods. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For your lorry, the mass in running order is the tare mass plus a standard driver mass of 75 kg. This figure serves this technical definition: you must not use it instead of a person’s actual mass when a question asks you to calculate the actual laden mass. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • One tonne equals 1,000 kg. If a sign shows 5.5 t, you compare this with 5,500 kg; if a table shows 26 t, this means 26,000 kg for the mass of the whole vehicle in the relevant case, not additional tonnes of goods. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

2MMA (maximum authorised mass), technical limits and available load capacity

A light truck with the driver on the left and three secured crates on its flatbed stands on a weighbridge beside a road.
The key idea

Respect your MMA, technical limits and limits for each axle.

3,500 kgMMA: minimum must be exceeded
7,500 kgMaximum MMA with C1

Remember

  • Check the MMA in the documents.
  • The space between MMA and tare includes people, goods and other added items.
  • Check each axle, each group and the whole vehicle.
  • With a trailer, check the combination’s authorised and technical limits too.

Exam trap: Wrong: An empty lorry always qualifies for C1. Right: The documented MMA decides whether your licence covers it.

Read the full explanation
  • Your C1 lorry has an MMA above 3,500 kg and up to and including 7,500 kg: the limit refers to the MMA recorded in its documents, even when you drive it empty. You study the scope of the licence and its trailer entitlements in the section «Light trailers and E extensions» of the module «C1 lorry licences and types of transport». [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • The maximum authorised mass, MMA, is the maximum mass permitted for using the laden vehicle on public roads. The technically permissible maximum mass depends on its construction and is specified by the manufacturer. You must comply with both limits: a general figure in the table does not allow you to ignore a lower technical or authorised value for the particular lorry. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • With an MMA of 7,500 kg and a tare mass of 4,200 kg, you have 3,300 kg available for people and other items not included in the tare mass, as well as goods. If the driver weighs 80 kg and you add no other mass, the goods can weigh up to 3,220 kg, provided you also comply with the axle limits. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • You can have a total mass below the MMA and still overload the rear axle by placing too much weight at the back. You can also comply with the limit for each individual axle and exceed the maximum for the axle group or the whole vehicle. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For a vehicle combination, the maximum authorised mass and the technically permissible maximum mass of the combination are separate limits. You must check both in the documents for the lorry and trailer. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

3Identify the axles and their functions

A light truck with secured cargo travels in the right-hand lane, showing its rear axle with twin wheels connected by the same axle.
The key idea

Identify your axles and their spacing before checking their limits.

Axle typeWhat you can do
RetractableRaise or lower it
Load relievingChange its load without lifting it

Remember

  • Add the mass carried by all wheels on the same axle.
  • Twin wheels do not multiply the axle limit.
  • Check the spacing and the table for that vehicle.
  • Check the limits of axles still on the ground.

Exam trap: Wrong: Raising an axle lets you overload the others. Right: Respect the limits of the axles still on the ground.

Read the full explanation
  • The axle load is the mass transmitted to the ground through all the wheels attached to that axle. If it has twin wheels, you add together the mass transmitted through all of them: you do not multiply the axle limit by the number of tyres. You must distinguish the driving function from the steering function, although one axle can perform both. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • An axle group comprises the axles that form part of a bogie. With two axles, it is called a tandem, and with three, a tri-axle tandem; by convention, a single axle is also considered a group. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • You must read the spacing d between the axles to choose the correct row in the table. A lorry tandem and a trailer tandem can have different limits with identical spacing. Simply counting four wheels or visually identifying two axles close together is not enough to assign an authorised mass to them. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • A retractable axle can be raised or lowered; with a load-relieving axle, you vary the load without lifting it. These devices allow you to adapt the load distribution to the expected conditions, but do not give you general permission to overload. You must check the limits for the axles that remain in contact with the ground and the actual configuration used on the road. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

4Single axles and minimum load on driven axles

A two-axle light truck travels to the right along a rural road, carrying boxes secured with straps and distributed across the flatbed and above the driven rear axle.
The key idea

Check maximum axle loads and minimum weight on your driven axles.

12 tSingle driven lorry axle
10 tSingle non-driven axle
25 %General minimum driven axle load
9 kg/cm²Maximum road surface pressure
Single lorry axleGeneral maximum
Driven12 t
Non-driven10 t

Remember

  • Also respect technical limits and the whole lorry’s limit.
  • Calculate driven axle load from the whole laden mass.
  • Euro-modular combinations and round timber loads may have an exception.
  • They must have enough driven axle load to start on an 8 % gradient.
  • Respect the tyres’ safety limits.

Exam trap: Wrong: Using 9 kg/cm² as tyre inflation pressure. Right: It is pressure on the road surface.

Read the full explanation
  • For a lorry, the general maximum for a single driven axle is 12 t and for a single non-driven axle it is 10 t. You must also apply their technical limits and those of the whole vehicle. You must not use the rows specifically for buses for a lorry driven under a C1 licence. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • If your lorry has an MMA of 7,500 kg and the manufacturer limits its front axle to 3,100 kg, you must comply with both figures even though they are lower than those in the general table. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • As a general rule, the driven axle or axles must bear at least 25 % of the total laden mass of the vehicle or combination. For an actual mass of 7,200 kg, this minimum is 1,800 kg on the driven axles. You must calculate it using the total laden mass, not just the goods. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For Euro-modular combinations or combinations carrying round timber, a proportion below 25 % may be permitted, provided they have enough mass on the driven axles to start moving on gradients of 8 %. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • You must also not drive if the tyres bear loads exceeding their safety standards or if the pressure on the road surface exceeds 9 kg/cm² of gross contact area. This last figure is not the inflation pressure you must set for the tyres: these are different quantities. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

5Motor vehicle tandem axles

A light truck with a green cab and orange cargo bed travels to the right in its lane, with both rear tandem axles visible on a road in a Mediterranean landscape.
The key idea

Your motor vehicle tandem limit depends on axle spacing and equipment.

75 %Minimum pneumatic spring effect
Motor vehicle tandem: spacingMaximum and conditions
d < 1.00 m12 t
1.00 m ≤ d < 1.30 m16 t
1.30 m ≤ d < 1.80 mNormally 18 t
1.30 m ≤ d < 1.80 m19 t: driven axle with twin tyres and air suspension or recognised equivalent
1.30 m ≤ d < 1.80 m19 t: also if each driven axle has twin tyres and maximum 9.5 t

Remember

  • Check the spacing between axles, called d.
  • Check the equipment before using the exceptional limit.
  • Suspension equivalence must be recognised.

Exam trap: Wrong: Applying 19 t just because there is air suspension. Right: You need 1.30 m ≤ d < 1.80 m and one of the specified equipment conditions.

Read the full explanation
  • For a motor vehicle tandem, if d is less than 1.00 m, the maximum for the group is 12 t. When 1.00 m ≤ d < 1.30 m, the maximum is 16 t. You must include exactly 1.00 m in the second range; do not treat it as a spacing of less than one metre. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • When 1.30 m ≤ d < 1.80 m, the ordinary maximum for the tandem is 18 t. Thus, 1.20 m or 1.25 m gives you 16 t, while 1.50 m gives you 18 t, unless the case meets the additional conditions that allow you to apply 19 t. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • Within that range from 1.30 m to less than 1.80 m, you can apply 19 t if the driven axle has twin tyres and air suspension or a recognised equivalent. This is also permitted if each driven axle has twin tyres and the maximum mass of each does not exceed 9.5 t. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • To apply 19 t, you must identify the equipment on the driven axle referred to in the table. For these purposes, suspension is air suspension when at least 75 % of its springing effect comes from a pneumatic device; equivalence must be recognised under the regulations. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

6Tandem and tri-axle groups on towed vehicles

A light truck with an orange cab and green box body travels to the right along a rural road, towing an empty trailer with two closely spaced axles.
The key idea

Use the trailer or semi-trailer table for towed axles.

Remember

  • Find their limits in “Articulated vehicles and road trains”.
  • Check the mass transmitted to the ground by the towed axles.
  • Check the vertical load received by the lorry too.

Exam trap: Wrong: Checking only the towed axles. Right: Check the vertical load received by the lorry too.

Read the full explanation
  • For a trailer or semi-trailer, you compare the mass transmitted by an axle group with the row for the towed vehicle. You find the tandem and tri-axle references together in the table in «Articulated vehicles and road trains», alongside the other heavy configurations. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • When checking a towed axle group, you use the mass transmitted to the ground through its axles; you also check the vertical load received by the lorry against the limits of the towing vehicle. This lets you identify which part of the combination reaches its capacity before you reach the overall maximum. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

7Total mass of a rigid lorry

A two-axle light rigid truck with secured crates on its flatbed stands on a road weighbridge in a Mediterranean landscape.
The key idea

Check your whole lorry’s weight and its axle weights separately.

18 tGeneral: two-axle rigid lorry

Remember

  • The general maximum does not extend your C1 licence.
  • Respect your lorry’s documented MMA and technical limits.
  • Count all the load when checking total mass.

Exam trap: Wrong: Respecting each axle is enough. Right: You must also respect the whole vehicle maximum.

Read the full explanation
  • For a two-axle rigid lorry, the general table sets 18 t, before the special increases provided for in its notes. For your C1, you must apply the MMA (maximum authorised mass) shown in the documentation and the vehicle's technical limits. The rows for heavy three- and four-axle rigid lorries appear for comparison in «Articulated vehicles and road trains». [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The total mass of a rigid lorry is the mass of the entire laden vehicle. For example, if your lorry has an MMA of 6,500 kg and weighs 6,700 kg on a weighbridge, you exceed its authorised mass even if the masses measured on its two axles are within their individual limits. To decide whether you can drive, you must check both the complete vehicle and each of its axles or axle groups. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

8Trailers and four-axle articulated vehicles

A two-axle light truck tows a two-axle trailer to the right in the lane nearest the viewer on a two-way road.
The key idea

Your trailer must meet licence, coupling and braking limits.

750 kgUnbraked trailer regulatory ceiling
10 %Conditional coupling proportion
1,000 kgConditional absolute coupling ceiling
Trailer or vehicle coveredRegulatory towing ceiling
Unbraked trailerTowing vehicle tare / 2 + 75 kg; maximum 750 kg
N2 and N3 towing a trailer with continuous braking1.5 times towing vehicle MMA
Trailer with overrun braking onlyTowing vehicle MMA; maximum 3,500 kg
Overrun braking only, off-road towing vehicle1.5 times towing vehicle MMA; maximum 3,500 kg

Remember

  • Apply the lowest relevant limit.
  • Check the documented combination limit and each unit’s authorisation.
  • For a centre-axle trailer with an even load, check the vertical coupling limit.
  • Use 10 % of trailer maximum mass or 1,000 kg, whichever is lower.
  • Count coupling load on the lorry and its rear axles.
  • Respect the coupling’s technical limits too.

Exam trap: Wrong: The towing formula is enough to choose a trailer. Right: Also respect your licence, documents and coupling.

Read the full explanation
  • The sum of the individual units' MMA values and the maximum authorised mass of the combination are different figures: for your lorry and trailer, you must check the documented limit for the combination as well as the authorisation for each unit. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For example, individual MMA values totalling 8,000 kg do not allow you to use that total mass if the combination is authorised for only 7,800 kg. You must adjust the load to the combination's limit and check the actual masses of both units. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The towable mass is limited by the towing vehicle's construction and the strength of the coupling. You must use the lowest applicable limit from the documentation and the rules for the trailer's braking system. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For an unbraked trailer, calculate half the towing vehicle's unladen mass and add 75 kg: unladen mass ÷ 2 + 75 kg, up to a maximum of 750 kg. With an unladen mass of 4,200 kg, you obtain 4,200 ÷ 2 + 75 = 2,175 kg and apply the 750 kg cap; a lower technical towing capacity takes precedence. [RGV, Annex IX, 4.1.2.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • On a centre-axle trailer with a uniformly distributed load, the vertical load on the coupling must not exceed the lower of these values: 10 % of the trailer's maximum mass or 1,000 kg. For 750 kg, the result is 75 kg. You must include this load when checking the mass of the towing vehicle and its rear axles, as well as observing the coupling's technical limits. [RGV, Annex IX, 4.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For N2 and N3 vehicles with a trailer with continuous braking, the towable mass cap is 1.5 times the towing vehicle's MMA. For a C1 vehicle with an MMA of 7,500 kg, the calculation gives 11,250 kg as the regulatory towing cap, subject to technical and driving licence limits. [RGV, Annex IX, 4.1.2.3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • With a trailer that has only overrun braking, the cap is the towing vehicle's MMA, or 1.5 times that MMA if it is an off-road vehicle, without exceeding 3,500 kg. For a lorry with an MMA of 7,500 kg, the limit for this braking system is 3,500 kg, subject to any lower technical capacity. [RGV, Annex IX, 4.1.2.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

9Articulated vehicles and road trains

A two-axle truck pulls a two-axle trailer using a short drawbar and hitch along a road in a Mediterranean landscape.
The key idea

Choose limits for your exact configuration and check every condition.

ConfigurationMaximum massLength or condition
Towed tandem: d < 1.00 / 1.00–<1.30 / 1.30–<1.80 / d ≥1.80 m11 / 16 / 18 / 20 tThird interval: 20 t for a reinforced tipping semi-trailer specifically for construction, civil engineering works or mining
Towed triple axle: d ≤1.30 / 1.30<d≤1.40 m21 / 27 td is axle spacing
Three-axle rigid lorry25 t; 26 t with specified equipment26 t: driven axle with twin tyres and air suspension or equivalent, or each driven axle with twin tyres and maximum 9.5 t per axle
Four-axle rigid lorry31 t; 32 t with two steering axles and specified equipment32 t: driven axle with twin tyres and air suspension or equivalent, or each driven axle with twin tyres and maximum 9.5 t per axle
Two-/three-axle trailer18 / 24 tWhole vehicle; axle limits also apply
Four-axle articulated, tractor 2 + semi-trailer 236 t; 38 t under the conditions in table 216.50 m; kingpin to rear 12 m; front horizontal distance 2.04 m
Articulated, five or more axles in table 2 configurations44 tHeavy transport reference
Road train: lorry 2 + trailer 2 / 2+3 / 3+2 or 336 / 42 / 44 tSee “Road train length”
Intermodal with 45-foot container or swap bodyUp to 2 t extra in combinations marked with an asterisk in table 2Dimensional conditions in “Length exceptions and aerodynamics”
Special transport of indivisible loadAs authorisedEscort by dimensions if over 3 m wide or 20.55 m long; officers if over 5 m wide

Remember

  • Identify the vehicle and number of axles.
  • Do not confuse an articulated vehicle with a road train.
  • Use exceptions only when you meet their conditions.
  • Heavy combinations need the appropriate licence.

Exam trap: Wrong: Giving 44 t to a 2 + 3 road train. Right: That road train allows 42 t; the relevant articulated vehicle has a different limit.

Read the full explanation
  • This table provides a reference for configurations in the shared goods transport syllabus. For your C1, you must apply the row corresponding to each vehicle and its documented limits; the masses for large combinations are comparative figures. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4). | Configuration | Maximum mass | Length or dimensional condition | | --- | --- | --- | | Trailer tandem axle group: d < 1.00 m / 1.00 ≤ d < 1.30 m / 1.30 ≤ d < 1.80 m / d ≥ 1.80 m | 11 / 16 / 18 / 20 t | In the third range: 20 t for a semi-trailer with a reinforced tipping body specifically for construction, civil engineering works or mining | | Trailer tri-axle group: d ≤ 1.30 m / 1.30 < d ≤ 1.40 m | 21 / 27 t | d is the axle spacing | | Three-axle rigid lorry | 25 t; 26 t with the specified equipment | 26 t: driving axle with twin tyres and air suspension or equivalent, or each driving axle with twin tyres and a maximum of 9.5 t per axle | | Four-axle rigid lorry | 31 t; 32 t with two steering axles and the specified equipment | 32 t: driving axle with twin tyres and air suspension or equivalent, or each driving axle with twin tyres and a maximum of 9.5 t per axle | | Two- / three-axle trailer | 18 / 24 t | Maximum masses for the complete vehicle; you must also observe its axle limits | | Four-axle articulated vehicle, tractor unit 2 + semi-trailer 2 | 36 t; 38 t under the conditions in table 2 | 16.50 m; from the kingpin to the rear of the semi-trailer: 12 m; from the kingpin to any point at the front, measured horizontally: 2.04 m | | Articulated vehicle with five or more axles, in the configurations in table 2 | 44 t | Heavy transport reference | | Road train: lorry 2 + trailer 2 / 2 + 3 / 3 + 2 or 3 | 36 / 42 / 44 t | Combination lengths in «Road train length» | | Intermodal transport with a 45-foot container or swap body | Increase of up to 2 t for combinations marked with an asterisk in table 2 | Dimensional conditions in «Length exceptions and aerodynamics» | | Special transport of an indivisible load | As authorised | Escort vehicle required on dimensional grounds if width exceeds 3 m or length exceeds 20.55 m; traffic officers required if width exceeds 5 m |

10Increases for technology and intermodality

An electric light truck with an orange battery beneath its cargo box travels to the right along a street in a Mediterranean urban setting.
The key idea

Technology increases cover extra technology weight and have conditions.

1 tAlternative fuel: maximum increase
2 tZero emission: maximum increase
1 tUrban service: conditional extra
Technology: rows with note; two-axle motor vehicles except busesMaximum increase
Alternative fuelUp to 1 t
Zero emissionUp to 2 t

Remember

  • Use increases only in rows with the relevant note.
  • They only cover the extra weight required by that technology.
  • They do not increase payload or extend your C1 licence.
  • For urban services, respect technical and axle limits.
  • An occasional city delivery is not enough for the urban increase.

Exam trap: Wrong: Using the increase to carry more goods. Right: It covers the extra weight of the technology.

Read the full explanation
  • Note (1) to table 2 also applies to two-axle motor vehicles, except buses: in the rows carrying that note, you may add to the MMA only the additional weight required by alternative-fuel technology, up to 1 t, or zero-emission technology, up to 2 t. This is not extra payload and does not extend the C1 MMA limit of 7,500 kg. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix). [RGCond, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4).
  • For vehicles intended for services in urban environments, up to 1 t more is permitted on top of these increases, without exceeding the technically permissible maximum mass or the maximum axle masses. You must check all the conditions; an occasional delivery within a town does not in itself justify applying any increase to a vehicle. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

11Round timber: specific masses

A five-axle articulated vehicle carries logs secured with straps in the right-hand lane of a road beside a forest and a sawmill.
The key idea

Identify round timber and check the required vehicle configuration and route.

LoadRound timber?
Felled trunks without tops or branches, and cut branchesYes
Bark, woodchips and sawdustNo

Remember

  • Check the configurations and routes allowed for these special masses.
  • It includes felled trunks without tops or branches, and cut branches.
  • It excludes bark, woodchips and sawdust.
  • With C1, keep within your lorry’s documented limits.

Exam trap: Wrong: Applying special masses to any wood load. Right: Check it is round timber and meets route and configuration conditions.

Read the full explanation
  • Round timber includes felled trunks with their tops and branches removed, and cut branches; bark, woodchips and sawdust are excluded. Its mass increases apply to heavy vehicle configurations and specific routes; for your C1, you must keep within the lorry's documented limits. [RGV, Annex IX, 1.28 and table 2, notes (3)-(5)](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

12Maximum lorry width

A light truck is parked entirely in a marked space on the roadway, with the pavement on its right and a narrow passage between buildings in the background.
The key idea

Measure your loaded width and check route restrictions.

2.55 mGeneral maximum width
2.60 mTemperature controlled exception
45 mmMinimum thickness per side wall
Lorry or bodyMaximum width
General, including load2.55 m
Temperature-controlled body with side walls at least 45 mm including insulation2.60 m

Remember

  • Include the load when measuring width.
  • Obey signs even when they are more restrictive.
  • Use technical measurements; do not deduct accessories yourself.

Exam trap: Wrong: Every refrigerated lorry can be 2.60 m wide. Right: It needs temperature-controlled bodywork and both side walls must be at least 45 mm thick, including insulation.

Read the full explanation
  • The general maximum width is 2.55 m, including the load. You must compare it with the actual width of your laden vehicle and the restrictions on your route. The fact that a lorry can legally be 2.55 m wide does not allow you to enter a street where a sign imposes a maximum of 2.50 m. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The 2.60 m width applies to fixed or movable superstructures of vehicles equipped for temperature-controlled goods, with each side wall at least 45 mm thick, including insulation. The exception requires both thermal conditioning and this minimum thickness for both side walls. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • Authorised dimensions are determined under the type-approval regulations applicable to the category. Use the vehicle's technical dimensions and the actual space occupied by the load; an accessory does not allow you to deduct centimetres arbitrarily when assessing whether your transport fits along the route. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

13General height limit and 4.50 m exceptions

A light truck with secured cargo is parked beside the right-hand kerb while a measuring pole reaches from the ground to the top of the load.
The key idea

Measure your loaded height and apply exceptions only to specified cases.

4 mGeneral maximum height
4.50 mExceptional height in specified cases
50 kmIndustrial route: must be shorter
Vehicle or caseMaximum height
General, including load4 m
Specialised vehicle transporter lorry or combination4.50 m
Recovery vehicle for damaged or broken-down vehicles4.50 m
Lorry or articulated vehicle with approved closed containers for combined, intermodal or ULD air transport4.50 m
Variable-height lorry or articulated vehicle carrying live animals, straw bales or fodder4.50 m
Industrial supplier on predetermined route under 50 km4.50 m

Remember

  • Measure from the ground to the highest point.
  • Check bridges, cables and route signs.
  • A loading crane alone does not qualify for the exception.

Exam trap: Wrong: Every straw load allows 4.50 m height. Right: The lorry or articulated vehicle must have variable height and be intended for that transport.

Read the full explanation
  • The general maximum height is 4 m, including the load. You must measure from the ground to the highest point of the vehicle as configured for road use. If the vehicle and its load reach 4.10 m, you need to meet an exception or have the appropriate authorisation; an empty load body measuring less than four metres is not enough. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • A maximum height of 4.50 m applies to vehicle transporters, both lorries and combinations specialising in carrying vehicles, and to recovery vehicles intended to remove vehicles damaged in accidents or broken down. The exception is linked to these uses: a crane for loading goods does not turn a lorry into a vehicle for recovering accident-damaged vehicles. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The table allows 4.50 m for lorries or articulated vehicles carrying approved enclosed containers for combined, intermodal or ULD-type air transport. It also covers variable-height lorries or articulated vehicles carrying live animals, straw bales and fodder. You must remember the variable-height requirement in this last case. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The 4.50 m cases include deliveries from suppliers to industrial premises on predetermined routes of less than 50 km. Exactly 50 km does not meet the requirement of ‘less than’. In all these cases, you must check clearances, bridges, overhead installations and local signs: the height permitted for the vehicle does not guarantee sufficient clearance along the entire route. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

14Length of rigid lorries, trailers and articulated vehicles

A green light rigid truck travels to the right along a rural road with a secured orange beam that fits entirely within its flatbed.
The key idea

Check your total loaded length and load projections separately.

12 mRigid lorry and trailer maximum
VehicleGeneral maximum length
Rigid lorry, including load12 m
Trailer12 m

Remember

  • More axles do not by themselves allow a longer lorry.
  • Measure between the ends of the loaded transport.
  • If the beam and body overlap, do not add their full lengths.

Exam trap: Wrong: Allowed projection automatically increases maximum length. Right: Projection and total length are separate limits you must meet together.

Read the full explanation
  • The general maximum length of a rigid lorry is 12 m, including the load. You must apply this value even if it has three or four axles: the number of axles may change the maximum mass, but does not in itself allow a greater length. The table also sets 12 m for a trailer. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • To measure a vehicle carrying a beam, you must identify the foremost and rearmost points of the loaded vehicle. If the beam and the load body overlap, you do not add their full lengths together. You must check separately how far the load projects and the overall length of the loaded vehicle, as these are different limits. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

15Road train length

Side view of a green light truck with a small orange trailer whose drawbar is coupled to a hitch fixed to the truck’s rear chassis, travelling to the right in its lane on a rural road.
The key idea

Measure your whole loaded road train, including the gap between its units.

18.75 mMaximum road train length
16.40 mLoading area including gap
15.65 mLoading area without gap
Road train measurement, loadedMaximum
Whole combination, including coupling gap18.75 m
Load start behind cab to trailer end, including gap16.40 m
Same area, excluding gap between units15.65 m

Remember

  • Include the coupling gap in your measurement.
  • Measure from the start of the load behind the cab to the trailer end.
  • Take measurements parallel to the vehicle’s length.

Exam trap: Wrong: Checking each unit length is enough. Right: Check the whole combination’s length too.

Read the full explanation
  • The general maximum length of a road train is 18.75 m, including the coupling and the load. You must measure the entire combination even if each unit complies with its individual maximum. [RGV, Annex IX, table 3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • From the front end of the loading area behind the cab to the rear end of the trailer, the permitted distance is 16.40 m; after subtracting the gap between the units, it is 15.65 m. You must take both measurements parallel to the longitudinal axis. [RGV, Annex IX, table 3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

16Length exceptions and aerodynamics

A light rigid truck with a cab roof fairing and rear aerodynamic devices travels to the right in its lane on a road through a Mediterranean landscape.
The key idea

Approved aerodynamics may allow extra length under conditions, without increasing load capacity.

15 cmConditional intermodal extra length
150 cmConditional articulated vehicle extra length
Vehicle or transport and conditionsLength exception
Approved cab and rear aerodynamic devicesMay project for their function; no extra load capacity
Intermodal with loaded or empty 45-foot container or swap body15 cm on lengths or distances with table 3 note (1)
Articulated vehicles carrying grouped indivisible bars, beams or tubes; length only exceededUp to 150 cm; no extra permitted mass

Remember

  • Check the cab and approved devices meet the conditions.
  • Retract or remove devices if safety could be affected.

Exam trap: Wrong: More aerodynamic length allows more load. Right: This exception does not increase load capacity.

Read the full explanation
  • Approved cabs and rear aerodynamic devices allow you to exceed the statutory length for their intended function, without increasing load capacity. You must fold, retract or remove the devices when safety is at risk. [RGV, Annex IX, table 3, notes (1) and (5), and section 7](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • In intermodal transport with 45-foot containers or swap bodies, loaded or empty, you may exceed the lengths or distances marked with note (1) in table 3 by 15 cm. [RGV, Annex IX, table 3, notes (1) and (5), and section 7](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • In articulated vehicles carrying bars, beams, pipes or similar items grouped as an indivisible load, you may add up to 150 cm if only the length limit is exceeded; this exception does not increase the permitted mass. [RGV, Annex IX, table 3, notes (1) and (5), and section 7](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

17Turning circle and outward swing

Overhead view of a light truck with a green cargo box and orange cab turning within a circular track bounded by two concentric white circles.
The key idea

Distinguish turning radii from the space your lorry swings into.

12.50 mOuter radius
5.30 mInner radius
0.80 mRigid lorry outward swing
1 mCategory N: raised axles
Outward swing caseLimit from reference plane
Rigid goods vehicle0.80 m
Category N with retractable or load-relieving axles raised1 m

Remember

  • You must be able to complete the circle in both directions.
  • No end may leave the area between the circles.
  • Allow for kerbs, obstacles and other road users when turning.
  • Check the position of retractable or load-relieving axles.

Exam trap: Wrong: 12.50 m is a diameter. Right: It is the outer radius.

Read the full explanation
  • The statutory radii are 12.50 m on the outside and 5.30 m on the inside. Every motor vehicle and combination must be able to complete a full 360° circular path in either direction within the ring bounded by these concentric circles, without any extremity projecting beyond it. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • The 12.50 m and 5.30 m measurements are radii, not diameters or lorry lengths. The width of this ring is 7.20 m, the difference between the two radii. This geometric requirement does not allow you to occupy any space you choose when actually turning: you must respect kerbs, obstacles and other road users. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • For a rigid goods vehicle, the annex also sets an outward swing limit of 0.80 m relative to the reference tangential vertical plane when entering the specified turn. With retractable or load-relieving axles raised, the value applicable to category N vehicles is 1 m; you must bear the axle position in mind. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

18Combinations in a Euro-modular configuration

An orange euro-modular combination with two trailers and numerous axles travels in the opposite direction to a green light truck on a two-way road in a Mediterranean landscape.
The key idea

Each euro-modular module must also meet its individual limits.

72 tMaximum combination mass
32 mMaximum combination length

Remember

  • Check each module, trailer or semi-trailer separately.
  • Identify more than six axle lines or at least three modules.
  • Use only approved routes and meet their conditions and technical requirements.

Exam trap: Wrong: Only the combination maximum matters. Right: Each unit must also meet its own limits.

Read the full explanation
  • Euro-modular combinations have more than six axle lines or at least three modules and may reach up to 72 t and 32 m. These are large combinations: each module must comply with the maximum limits for its type, and you may drive them only on designated routes and under the statutory conditions. [RGV, Annex IX, 1.23, tables 2 and 3 and section 6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

19Indivisible loads and front and rear projections

A light truck travels to the right carrying an indivisible beam secured with straps and projecting beyond the front and rear, with a red and white striped board at its rear end.
The key idea

Indivisible loads may project under conditions, while meeting the permitted total length.

5 mLength separating the cases
2 mFront projection: longer lorry
3 mRear projection: longer lorry
Goods-only lorry: indivisible length load, correctly securedFrontRear
Vehicle over 5 mUp to 2 mUp to 3 m
Vehicle 5 m or shorterUp to one third of its lengthUp to one third of its length

Remember

  • These projections apply to your lorry used only for goods.
  • The load must be indivisible because of its length.
  • Secure the load as required.
  • Check the total length of the transport too.
  • Do not divide a load if doing so adds needless cost or risks damage.
  • It also exceeds ordinary limits because of its mass or dimensions.

Exam trap: Wrong: Adding projections to the rigid lorry’s 12 m. Right: Meet both projection limits and the permitted total length.

Read the full explanation
  • On your lorry used exclusively for goods, a load that is indivisible lengthways may project up to 2 m at the front and 3 m at the rear if the vehicle is more than 5 m long; if it is 5 m long or less, it may project by up to one third of the vehicle's length at each end, provided you meet the load-securing requirements. See «Load securing and safety», «When a load may project» for the full explanation. [RGC, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • You must comply with both the permitted projection and the authorised overall length at the same time: the projection limits do not give a 12 m rigid lorry an extra five metres for its load. [RGC, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • A load is indivisible when dividing it for transport causes unnecessary cost or risk of damage and its mass or dimensions mean it cannot fit on a vehicle or vehicle combination that complies with the ordinary maximum limits. A group of items of the same nature and purpose is also accepted, provided it does not exceed any dimensions other than those exceeded by the largest item, or the maximum combination and axle limits in the tables. [RGV, Annex IX](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).

20Side projections and protection

A light truck travels in the right lane carrying a centered indivisible piece secured to its flatbed, projecting slightly on both sides with orange padding protecting the ends.
The key idea

Allowed side projections do not let you exceed maximum total width.

0.40 mMaximum projection per side
2.55 mMaximum total width

Remember

  • The load must be indivisible.
  • Its smallest dimension must exceed the goods lorry’s width.
  • Protect the projecting ends.
  • Check projection and total width together.

Exam trap: Wrong: The 0.40 m allows you to exceed 2.55 m overall. Right: You must meet both limits.

Read the full explanation
  • If the smaller dimension of an indivisible load exceeds the width of your goods lorry, it may project by up to 0.40 m on each side, with a maximum overall width of 2.55 m; you must protect its ends. See «Load securing and safety», «Side projections and overall dimensions» and «Protection and the V-20 panel» to apply the protection and dimensional requirements. [RGC, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).

21Marking projecting loads

A light truck travels by day in the right lane with a timber load projecting from the rear and a red and white diagonally striped panel at its rearmost end.
The key idea

Mark projecting loads and add lights when required.

Projecting load: at night or greatly reduced visibilityExtra light
RearRed at rear
FrontWhite at front

Remember

  • If the load projects behind, use the V-20 panel.
  • At night or in greatly reduced visibility, add the required light.
  • See “Load securing and safety” for panel placement and side marking.

Exam trap: Wrong: The panel is enough at night for a rear projection. Right: As well as V-20, you need a red rear light.

Read the full explanation
  • If your load projects at the rear, you must mark it with V-20; at night or when visibility is significantly reduced, you must also display a red light at the rear and, if the load projects at the front, a white light at the front. See «Load securing and safety», «Protection and the V-20 panel» and «Lighting projecting loads» for the placement of one or two panels and side marking requirements. [RGC, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).

22When you need special transport authorisation

A driver and a traffic officer review a document beside a stationary light truck carrying a long pole secured with straps and marked at its rear end.
The key idea

Get additional road use authorisation before exceeding limits without an applicable exception.

Remember

  • This applies to technical features or indivisible loads exceeding limits.
  • Applying for authorisation does not mean you have it.
  • A goods transport authorisation does not replace road use authorisation.
  • Plan a route the transport can physically use.
  • Follow the authorisation conditions.

Exam trap: Wrong: Allowed projections always avoid authorisation. Right: If total length exceeds the ordinary limit and no exception applies, you need additional authorisation.

Read the full explanation
  • If your vehicle's technical characteristics or an indivisible load cause you to exceed the applicable maximum limits and you do not qualify for an exception, you must obtain the appropriate autorización complementaria de circulación (additional authorisation to use the road) before setting off. The traffic authority grants it after obtaining a binding report from the road authority and checking the transport authorisation required by law. [RGV, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a14).
  • The authorisation may cover a limited number of journeys or a specified period. Submitting an application or holding a goods transport authorisation does not mean you have been granted the additional authorisation to use the road. [RGV, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a14).
  • An 11 m rigid lorry carrying an indivisible pole that brings the overall length to 14.50 m exceeds the ordinary maximum of 12 m. You must check the appropriate additional authorisation, even if the front and rear projections are each within the limits of article 15. This check prevents you from confusing the amount of projection with the overall length of the loaded vehicle. [RGV, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a14).
  • You must plan a physically feasible route and comply with access restrictions. The conditions for road use set out in the authorisation take precedence over the applicable general conditions under the terms of Annex III. [RGC, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).

23Conditions for special transport

A light truck with a secured indivisible load and its headlights on travels along a conventional road, following at a distance behind a pilot vehicle with amber lights.
The key idea

Follow your special transport authorisation and stop travelling when conditions require it.

50 mMinimum gap to vehicle ahead
150 mMinimum visibility ahead and behind
70 km/hGroup 1: general authorisation
60 km/hGroup 1: specific/exceptional speed ceiling
Group 1 special transport authorisationMaximum speed, unless lower limit
Generic70 km/h
Specific60 km/h
ExceptionalSet by authorisation; never over 60 km/h

Remember

  • Keep dipped headlights on.
  • Stop and park off the carriageway and hard shoulder.
  • Help others overtake without forcing sudden changes; stop if needed.
  • Stop travelling if weather makes driving dangerous.
  • Also stop if visibility ahead or behind is under 150 m.
  • In both cases, leave the road platform.

Exam trap: Wrong: A general authorisation always allows 70 km/h. Right: For group 1, obey any lower ITV or road limit.

Read the full explanation
  • When undertaking special transport, you must comply with the conditions of your authorisation and the general conditions in Annex III: keep at least 50 m behind the vehicle ahead, keep your dipped beam on at all times, and stop and park off both the carriageway and the arcén (hard shoulder). You must help faster vehicles overtake, stopping if necessary, without forcing them to change speed or direction abruptly. The escort requirements based on dimensions are summarised in the table in «Articulated vehicles and road trains». [RGC, Annex III, section 1.ª.1, 2 and 4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).
  • You must stop travelling and move off the road platform when adverse weather makes driving dangerous or when visibility ahead or behind is less than 150 m. This obligation applies while you are undertaking the transport operation, in addition to restrictions shown by signs or given by traffic officers. [RGC, Annex III, section 1.ª.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).
  • In group 1, your maximum speed is 70 km/h with a generic authorisation and 60 km/h with a specific authorisation. With an exceptional authorisation, you must comply with the speed specified in it, which cannot exceed 60 km/h. In all three cases, a lower speed limit on your tarjeta ITV (vehicle roadworthiness test card) takes precedence. For example, if you have a generic authorisation but your tarjeta ITV limits you to 50 km/h, you must keep to 50 km/h as well as any lower restriction applicable on the road. [RGC, Annex III, group 1.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii).

24Signs limiting mass

A light truck is stopped before a closed barrier, with each axle on a weighing platform connected to a separate indicator without numbers.
The key idea

Each mass sign requires you to check a different weight.

SignWeight to compare
R-201Actual laden vehicle mass
R-202Actual mass on each axle
R-107: goods vehicleVehicle MMA

Remember

  • At R-201, count the lorry, people and actual goods.
  • At R-202, check the most heavily loaded axle.
  • Do not use the axle average to justify passing.
  • R-107 can also apply when your lorry is empty.

Exam trap: Wrong: Comparing R-202 with the axle average. Right: Check the mass transmitted by all wheels on each axle.

Read the full explanation
  • R-201, Mass limit, prohibits you from proceeding if your laden mass exceeds the number of tonnes shown. You must compare this with your actual mass for the journey, including people and goods. With a sign showing 5.5 t, an actual mass of 5,400 kg does not exceed that threshold, although you must comply with all other limits. [RD 465/2025, catalogue, R-107 and R-201/R-202](https://www.boe.es/diario_boe/txt.php?id=BOE-A-2025-12199).
  • R-202, Axle mass limit, prohibits you from proceeding if the mass transmitted by all the wheels of any one axle exceeds the value shown. You must know the load on your most heavily loaded axle: dividing the total mass by the number of axles can conceal an actual overload and does not demonstrate compliance with the sign. [RD 465/2025, catalogue, R-107 and R-201/R-202](https://www.boe.es/diario_boe/txt.php?id=BOE-A-2025-12199).
  • At an R-202 sign showing 4 t, you cannot proceed in a C1 lorry with 2,800 kg on the front axle and 4,400 kg on the rear axle. Your total mass is 7,200 kg and the average per axle is 3,600 kg, but the rear axle exceeds the limit shown. [RD 465/2025, catalogue, R-202](https://www.boe.es/diario_boe/txt.php?id=BOE-A-2025-12199).
  • R-107 uses the goods vehicle's MMA (maximum authorised mass). If you drive a lorry with an MMA of 7,500 kg and an actual mass of 5,000 kg, you are prohibited from entering at an R-107 sign showing 5.5 t; however, those 5 t of actual mass do not exceed an R-201 limit of 5.5 t. The R-107 prohibition also applies when your lorry is empty. [RD 465/2025, catalogue, R-107](https://www.boe.es/diario_boe/txt.php?id=BOE-A-2025-12199).

25Length, width and height restriction signs

A driver uses a measuring pole to check the load height of a light truck stopped in a paved area, well away from a low stone underpass.
The key idea

Compare dimension signs with your transport’s actual loaded measurements.

SignLoaded measurement to check
R-203Total vehicle or combination length
R-204Maximum width
R-205Effective height to highest point

Remember

  • Always include the load in your measurements.
  • With a trailer, check the whole combination’s length.
  • Matching the figure does not exceed it.
  • Check the actual measurement and that passage is safe.
  • Meet mass and axle limits too.

Exam trap: Wrong: The general maximum lets you ignore a lower sign. Right: Obey the sign restriction too.

Read the full explanation
  • R-203, Length restriction, applies to the vehicle or vehicle combination including its load. You must compare the overall length, not just the load body or the towing vehicle. At a 10 m sign, you must not enter with a loaded lorry measuring 10.20 m, even if its unladen length is less than the limit. [RD 465/2025, catalogue, R-203 to R-205](https://www.boe.es/diario_boe/txt.php?id=BOE-A-2025-12199).
  • R-204, Width restriction, refers to the maximum width including the load. At a 2 m sign, you must not enter if you exceed that width; at a 2.50 m sign, you must not enter with your 2.55 m lorry either, even if it complies with the general maximum. You must check route restrictions when planning and when you reach each access point. [RD 465/2025, catalogue, R-203 to R-205](https://www.boe.es/diario_boe/txt.php?id=BOE-A-2025-12199).
  • R-205, Height restriction, includes the load. At a 3.50 m sign, you must not enter with a height of 3.60 m, even if your lorry is under 4 m; an exemption allowing a vehicle height of 4.50 m does not allow you to enter under a 4 m restriction either. You must compare your actual height when travelling, including any components that determine the highest point. [RD 465/2025, catalogue, R-203 to R-205](https://www.boe.es/diario_boe/txt.php?id=BOE-A-2025-12199).
  • These signs prohibit you from exceeding the stated figure: matching it does not mean exceeding it. Even so, you must make sure you know the actual measurement and that you can proceed safely; a theoretical match does not correct a measurement error or remove obstacles. You must comply with the mass, axle and all dimension restrictions at the same time. [RD 465/2025, catalogue, R-203 to R-205](https://www.boe.es/diario_boe/txt.php?id=BOE-A-2025-12199).

26Speed limiter: vehicles that must have one

A driver wearing a seat belt drives a truck in the right lane of a rural road, with the speedometer needle at the end of a green arc marked by an orange stop.
The key idea

Your lorry may need a speed limiter even within the C1 MMA limit.

90 km/hLimiter: goods vehicles covered
100 km/hLimiter: passenger vehicles covered
25 km/hDesign speed must exceed this
Vehicles covered by dates, conditions and exemptionsLimiter settingFirst registration and conditions
Goods N290 km/hFrom 1 January 2005.
Earlier goods N290 km/hBetween 1 October 2001 and 1 January 2005, if they meet the specified Euro 3 emissions limits. For national and international transport.
Goods N390 km/hFrom 1 January 1994; also between 1 January 1988 and 1 January 1994, according to the application timetable.
Passenger M2 and M3100 km/hAccording to the applicable dates, conditions and exemptions.

Remember

  • Check category, registration date, emissions and exemptions.
  • The rule covers road vehicles with at least four wheels.
  • For N2 and N3, check when and under what conditions it applies.
  • N2: maximum mass above 3.5 t and up to 12 t inclusive.
  • N3: maximum mass above 12 t.
  • The limiter setting does not let you exceed road limits.

Exam trap: Wrong: A C1 lorry is exempt because it is under 7,500 kg. Right: Included lorries must have a limiter based on category, date and conditions.

Read the full explanation
  • RD 1417/2005 applies to road vehicles in categories M2, M3, N2 and N3 with at least four wheels and a maximum design speed above 25 km/h, subject to its application dates and exemptions. [RD 1417/2005, art. 2](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a2).
  • If you drive a category N2 or N3 lorry subject to RD 1417/2005, you must have its limiter set so that its speed cannot exceed 90 km/h. This requirement includes a C1 light lorry within those categories and dates, even if its MMA (maximum authorised mass) is below 7,500 kg. [RD 1417/2005, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a4).
  • Category N2 covers goods vehicles with a maximum mass above 3.5 t and up to and including 12 t; N3 covers those above 12 t. A lorry with a maximum mass of 7.5 t belongs to N2: the type-approval classification and the scope of your licence are different matters. [Regulation (EU) 2018/858, art. 4](https://www.boe.es/buscar/doc.php?id=DOUE-L-2018-81001&lang=es).
  • For an N2 lorry, article 5 of RD 1417/2005 requires you to have a limiter if its registration date is 1 January 2005 or later. You also need one for a lorry registered between 1 October 2001 and 1 January 2005 that meets the Euro 3 emission limits specified in that article, for both national and international transport. The first registration date and documented emissions determine whether your lorry is covered. [RD 1417/2005, art. 5](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a5).
  • For N3, the requirement covers lorries registered from 1 January 1994 and those registered between 1 January 1988 and 1 January 1994 according to the timetable in article 5. The first registration date matters: your lorry's mass alone does not determine whether the requirement applies in every case. [RD 1417/2005, art. 5](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a5).
  • For passenger transport categories M2 and M3 subject to the decree, the setting is 100 km/h. For your goods lorry, your answer is 90 km/h; the limiter setting and the speed limits for each road serve different purposes. [RD 1417/2005, art. 3](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a3). [RD 1417/2005, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a4).

27Speed limiter exemptions and operation

A technician checks the speed limiter of a light truck parked outside a workshop, beside the open right door, with the steering wheel on the left side across the cab.
The key idea

Keep your limiter working and check whether you qualify for an exemption.

50 × 80 mmMinimum plate dimensions
ExemptionCondition to check
Armed Forces, law enforcement, civil protection, fire and other emergency servicesUse specified by the rule
Speed limited by designCannot exceed the relevant speed
Scientific testsVehicle intended for road tests
Public urban serviceUsed exclusively for that service in urban areas

Remember

  • Use an authorised workshop if it fails or a seal is broken or removed.
  • Do not remove the visible cab plate or break its seals.
  • Respect lower road limits.
  • An urgent delivery does not make you an exempt emergency service.
  • Regular city deliveries do not prove the public urban service exemption.

Exam trap: Wrong: An urgent delivery exempts you from the limiter. Right: The exemption applies to the emergency services specified by the rule.

Read the full explanation
  • Vehicles used by the Armed Forces, law enforcement agencies, civil protection, fire services and other emergency services are exempt. The exemption depends on the use specified in the legislation; you cannot claim it for a delivery lorry because you have an urgent delivery. [RD 1417/2005, art. 7](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a7).
  • Vehicles whose design prevents them from exceeding the relevant speed, those intended for scientific road tests and those used only for public services in urban areas are also exempt. Regularly delivering goods in a town or city does not, on its own, establish that you qualify for the last exemption. [RD 1417/2005, art. 7](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a7).
  • You must have a type-approved device that complies with the applicable technical requirements; authorised bodies or workshops must install and check it. [RD 1417/2005, arts. 6 and 8](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a6).
  • Your limiter must work correctly at all times. If it fails, or work on your vehicle or tachograph breaks or removes a seal, you must have it checked by an authorised body or workshop. [RD 1417/2005, art. 8](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a8).
  • After each check, the workshop fits a plate measuring at least 50 × 80 mm in a visible place in the cab, sealed or attached so that removing it destroys it. It shows the workshop's name and authorisation code, the installation or check date and «v = ... km/h». You must keep the plate and its seals intact. [RD 1417/2005, art. 15.1 and annex, section 5](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a15).
  • The limiter does not replace your duty to obey a lower limit or control your lorry's speed. If a sign imposes 60 km/h, you must obey it even if the device is set to 90 km/h; the limits for each road are covered in «Speed and safe following distances». [RGC, arts. 45 and 52](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45).
  • If you take part in or assist with tampering with the limiter, you commit a very serious infringement; the penalty and loss of points are explained in «The tachograph and its records», «Penalties you must distinguish». [Traffic Act, art. 77.m](https://www.boe.es/buscar/act.php?id=BOE-A-2015-11722#a77).

Check masses before your journey

You must meet every requirement: complying with the total MMA (maximum authorised mass) alone is not enough.

  1. Identify the unladen mass, MMA and technical maximum limits for the vehicle and, where applicable, the combination in their documents.
  2. Calculate or weigh the actual mass, including the driver, goods and all other items present.
  3. Select the total mass row according to the vehicle units, axles and technical conditions; check whether any exception applies to the operation.
  4. Check each axle and axle group, taking account of spacing and equipment, as well as the minimum load on the driving axles.
  5. Compare the results with the documents and the signs along your route; adjust the load or route if you exceed any limit.

Check a projecting load

You must distinguish the permitted overhang from the authorised overall dimensions.

  1. Identify whether the load is indivisible and whether the vehicle is intended exclusively for carrying goods.
  2. Measure the vehicle and apply the corresponding overhang limit: over 5 m or up to and including 5 m.
  3. Measure the overall laden length, width and height; check which exceptions actually apply.
  4. If you exceed an applicable maximum, obtain the relevant supplementary authorisation before driving.
  5. Protect the ends and fit panels and lights where required; check the restrictions along your route.

Answer a question about an access restriction

You must compare the figure with the quantity specified by the sign.

  1. Identify whether the sign limits laden mass, axle mass, length, width or height.
  2. For R-201, use the actual mass; for R-202, check each axle; for R-203 to R-205, include the load.
  3. Convert tonnes to kilograms if the figures use different units.
  4. Check whether you exceed the figure, without confusing equality with an excess.
  5. Check the other restrictions: complying with one sign does not show that the entire route is permitted.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module