Theory · A1 Licence - 125 cc Motorcycle · Module 14 of 18

Risks and prevention on a motorbike

You will learn to recognise visibility, grip, weather, speed, group riding and fatigue risks, and reduce them on your motorbike. You will be able to answer exam questions that require you to distinguish a legal obligation from a recommendation and choose the response that preserves control, space and time to react.

33 min read26 sectionsReviewed Nov 3, 2026
A rider wearing a full-face helmet and a bright jacket rides a 125 cc motorcycle on a wet road, with a car far ahead and leaves on the shoulder.
Anticipation and space to prevent motorcycle risks

1Your vulnerability on a motorcycle

A rider wearing a helmet and protective clothing rides a lightweight motorcycle in their lane towards a bend with wet patches, while a car approaches in the opposite lane in a Mediterranean landscape.
The key idea

You need more safety space on a motorcycle because you have less protection.

Remember

  • Set off rested and choose a suitable route.
  • Check yourself, your motorcycle and the road conditions together.
  • Expect changes in grip and visibility.
  • Do not rely only on experience or knowing the road.
  • Your helmet reduces injuries but does not prevent crashes.
  • Avoid distractions, inappropriate or excessive speed, alcohol, drugs and fatigue.

Exam trap: Wrong: protective clothing makes any speed safe. Right: always adapt your speed to conditions.

Read the full explanation
  • On your two-wheeled A1 motorcycle, you must maintain your balance while sharing the road with vehicles of much greater mass. Your small outline can be difficult to detect, and you have no protective passenger compartment. A manoeuvre that a car can tolerate may end in a fall if you lose grip.
  • A road accident involves the human factor, the vehicle and the road and its surroundings, and these almost always combine. The most common causes include distraction, inappropriate or excessive speed, alcohol or other drugs, and fatigue or drowsiness. A wet road surface, little experience and entering a bend too fast can combine and leave you with no margin for error. [DGT, Road safety questions, unit 1](https://sede.dgt.gob.es/export/sites/dgt/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2026/MANUAL-II-Cuestiones-de-Seguridad-Vial.pdf) [DGT, causes of vehicles leaving the road](https://www.dgt.es/comunicacion/noticias/20260522-salidas-de-via-nos-matamos-solos/)
  • You can reduce risks through specific decisions: set off well rested, choose a suitable route and anticipate changes in grip and visibility. Knowing the road or having driven for years does not guarantee that conditions are the same as on your last journey.
  • A helmet and protective clothing can reduce the consequences of a fall, but they do not prevent an accident or make an inappropriate speed safe. To choose them and learn about their requirements, see “Motorcyclist protective equipment”.

2Experience and your personal safety margin

A rider wearing protective gear practices between cones on a 125 cc motorcycle in a clear paved practice area while an instructor watches.
The key idea

Adapt your riding to your motorcycle and your experience.

Remember

  • Get used to a different motorcycle gradually.
  • Practise using the controls before tackling difficult routes.
  • Check the weather and plan alternatives before setting off.
  • Postpone your journey if weather or tiredness makes riding unwise.
  • Do not rely on acceleration you have not checked safely.

Exam trap: Wrong: a small engine always makes riding safe. Right: you can still ride too fast for conditions.

Read the full explanation
  • You must become familiar with how the motorcycle responds, especially if you change models. Its weight, height, power delivery and ergonomics affect your ability to control it. A motorcycle authorised for your licence may still require practical familiarisation before you ride in rain or heavy traffic.
  • If the controls are not automatic for you, using them takes attention and may make you tire sooner. Practise in suitable conditions and gradually increase the difficulty of your journeys.
  • Do not judge risk only by engine capacity or the motorcycle’s model name. A sports bike, trail bike and scooter have different characteristics depending on the model, and no category guarantees stability on oil or ice. Adapt your decisions to the specific vehicle and your abilities.
  • Before setting off, check the weather forecast, the state of your route and possible alternatives. If wind, snow or tiredness make the journey unwise, you can postpone it or choose another form of transport. Changing your plan is a preventive measure, even for a short or familiar journey.
  • A 125 cc motorcycle can also reach a speed that is inappropriate for its surroundings. On hills, with a passenger or into a headwind, it may regain speed more slowly than you expect. Plan your route and do not start a manoeuvre relying on acceleration you have not checked in safe conditions.

3Looking far ahead and recognising nearby hazards

A helmeted motorcyclist travels in the right lane well behind a van, with a metal cover visible in the road surface, a garage entrance on the right and a bend ahead.
The key idea

Look at different distances and leave space to spot hazards.

Remember

  • Look far ahead and check the nearby road surface too.
  • Leave more space behind vehicles so you can see better.
  • Watch garages, junctions and gaps between parked vehicles.
  • Even with priority, be ready to respond carefully.
  • If you cannot see properly, fix the problem somewhere safe.

Exam trap: Wrong: having priority removes danger. Right: others can make mistakes or fail to see you.

Read the full explanation
  • To detect a bend and a nearby patch of hazard in time, you need to observe at different distances; follow “Looking far ahead and scanning nearby” in “Preventive and efficient motorcycle riding”.
  • Leave space behind the vehicle in front so that it does not hide the road surface or side entrances. If you ride close behind a van, you lose visibility precisely when you need more time to interpret a hazard. Increasing the gap improves what you can see and your response margin.
  • Pay attention to places from which someone could emerge: between parked cars, behind a bus, from a garage or beside a junction. Even when you have priority, prepare a cautious response. Having priority does not prevent another road user from making a mistake or failing to detect you.
  • You must maintain a sufficient field of vision and remain attentive at all times. A fogged visor or a load that makes it difficult to look compromises this obligation; correct the problem in a safe place before continuing. [RGC, art. 18](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a18).

4Making yourself visible

A motorcyclist wearing a helmet and a green jacket with reflective strips rides in their lane during daylight with the motorcycle’s dipped headlight on, along a rural road.
The key idea

Make yourself visible and leave safety space even when you think others see you.

Visibility aidWhat you must remember
Light or bright clothingStands out depending on the background and light
Reflective materialsReturn light they receive
Both aidsDo not replace lights or guarantee others see you

Remember

  • Keep your motorcycle's dipped beam on during the day too.
  • Daytime running lights and position lights do not replace dipped beam.
  • Choose a legal position where you can see and be seen.
  • Signal your intentions and avoid unexpected movements.
  • Do not accelerate to force your way through or make noise.

Exam trap: Wrong: someone looking towards you has recognised you. Right: leave space in case they have not seen you.

Read the full explanation
  • You can make it easier for others to identify you by wearing light or bright colours and retro-reflective elements. Bright colours stand out depending on the background and ambient light; reflective elements return the light that reaches them. Neither guarantees that every driver has seen you, and neither replaces your motorcycle’s lights.
  • On your motorcycle, you must use dipped-beam headlights during the day on any road subject to traffic legislation; daytime running lights or position lights alone do not replace them. Daytime dipped-beam headlights are also required for all vehicles in reversible lanes, temporary additional lanes or lanes opened to traffic in the opposite direction to normal, and for vehicles covered by articles 41 and 42. See “Motorcycle lights and signals” for these lanes. [RGC, art. 104.a and b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a104).
  • Choose a legal position within the lane from which you can see and be seen, with clearance from obstacles. No part of the lane is always safest: bends, vehicles that hide you, doors and dirt on the road surface all vary.
  • Do not assume that someone has recognised you just because they look in your direction. A driver may misjudge your distance or how quickly you are approaching, especially when there is only one light as a reference. Keep a margin from drivers waiting to join the road or turn; do not accelerate to force your way through.
  • Do not rely on exhaust noise to warn others that you are there. It may not reach the other driver or help them locate you. Communicate your intentions with the appropriate signals and predictable movements; revving sharply to make noise adds risk without confirming that you have been seen.

5Other vehicles’ blind spots

A helmeted motorcyclist rides a 125 cc motorcycle at a generous distance behind an orange truck in the right-hand lane of a road.
The key idea

Avoid staying where another driver cannot see you.

Remember

  • You can be hidden beside vehicles of any size.
  • Expect hidden areas around lorries and buses.
  • Do not wait close to the cab or its front right corner.
  • If another vehicle turns, avoid its path and keep a safe escape route.
  • Do not always rely on blind spot detectors.

Exam trap: Wrong: seeing the driver in their mirror proves they see you. Right: they may not be looking at you.

Read the full explanation
  • A blind spot is an area that another driver cannot see using their usual means of observation. It can be beside a car, a van or a lorry. A motorcycle’s narrow profile makes it easy for it to remain hidden even when it seems very close to the driver.
  • To reduce your exposure to hidden areas, follow “Blind spots and seeing each other” in “Preventive and efficient motorcycle riding”.
  • Beside lorries and buses, expect areas the driver cannot see in front, behind and to the sides. Do not wait to join the road close to the cab or its front right corner. A large vehicle may start turning and close a space where the motorcycle seemed to fit.
  • Seeing the driver in their mirror is a useful way to avoid some hidden areas, but it does not prove that they are looking at you or have identified you. Do not assume that every vehicle has blind-spot detectors or that these systems always detect a motorcycle.
  • If a vehicle signals a turn or starts moving, keep a safe escape route and avoid entering its path. See “Manoeuvres on your motorcycle” for overtaking and changing lanes.

6Your mirrors and direct vision

A motorcyclist rides a 125 cc motorcycle in the right-hand lane and looks at a mirror reflecting the orange car following behind.
The key idea

Adjust your mirrors and check the space before moving.

Convex mirror featureWhat you must remember
Wider field of viewYou can see a larger area
Image of other vehiclesThey can look smaller and further away

Remember

  • Adjust and clean your mirrors before setting off.
  • Check they are secure from your normal riding position.
  • Look behind and to both sides.
  • Keep sideways checks brief so you do not miss hazards ahead.
  • Check the area again before changing position.

Exam trap: Wrong: your indicator clears your blind spot. Right: you must look before moving.

Read the full explanation
  • Before setting off, adjust your mirrors from your normal riding position and check that they are clean, secure and give you a clear view. You must be able to see behind and to both sides without adjusting them while riding. Poor adjustment impairs your perception even in bright conditions.
  • A convex mirror gives you a wider field of view, but can make vehicles appear smaller and further away. This image can make you underestimate how quickly they are approaching; follow “Blind spots and seeing each other” in “Preventive and efficient motorcycle riding” to complete your observation.
  • Looking to the side for too long can make you lose sight of an obstacle ahead: allow enough time and space to observe without changing your motorcycle’s path.
  • As you approach a traffic queue, vehicles behind you may threaten your stopping space; follow “If someone follows you too closely” in “Preventive and efficient motorcycle riding”.
  • Before changing lane position, you need recent information about the area you are going to occupy. The indicator signals your intention, but does not confirm that anyone has seen you or clear a blind spot.

7Grip: recognise the road surface

A helmeted rider travels upright on a 125 cc motorcycle in their lane on dry asphalt, approaching a wet area beneath trees.
The key idea

Ask less of your motorcycle when the road has less grip.

Road surfaceGrip you can expect
Rough, dry and cleanUsually better
Polished, dirty or wetUsually worse
Smooth, wet cobblestonesCan be especially slippery

Remember

  • Slow down before reaching a surface with less grip.
  • Avoid hard braking while turning sharply.
  • Slow down if you could spray water or throw gravel at others.
  • With new tyres, ride gently and follow the manufacturer's instructions.
  • Do not weave or change tyre pressures to warm them.

Exam trap: Wrong: a dark road surface guarantees grip. Right: check its condition and adapt your riding.

Read the full explanation
  • You should expect better grip on a rough, dry and clean surface than on a polished, contaminated or wet one. Not all asphalt behaves in the same way; smooth, wet cobbles can be particularly slippery. The dark appearance of the surface alone does not tell you how much grip you have.
  • The available grip has to be shared between braking, accelerating and changing direction. If you demand a lot of turning and braking at the same time, you can exceed that margin. You must reduce your demands when the surface changes and avoid leaning sharply on surfaces where grip is uncertain.
  • Anticipate transitions: a dry section may lead into a wet area beneath trees, a repaired section or a joint. Slow down before you reach it and maintain a steady line.
  • You must moderate your speed on slippery surfaces and whenever you may throw water or gravel at other road users. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46).
  • The condition of your tyres, brakes and suspension affects your available margin. If your tyres are new, start with gentle acceleration, braking and leaning, and follow the manufacturer’s instructions. Do not weave or change the pressure to warm them up; there is no running-in distance that guarantees the same grip for every model.

8Road markings, covers and rails

A helmeted rider crosses a wet zebra crossing on an upright 125 cc motorcycle in the right-hand lane, with no pedestrians present.
The key idea

Slow down before crossing paint, metal or rails.

SurfaceDanger you must expect
Wet paintCan have less grip than the surrounding road
Wet metal covers and platesCan be very slippery
Rails almost parallel to your pathCan trap or deflect your wheel

Remember

  • If crossing a marking is legal, cross smoothly with little lean.
  • Respect markings and pedestrians' priority, even if you must stop first.
  • Avoid sudden braking, acceleration or steering on paint.
  • Spot covers early without sudden lane changes.
  • Slow down before crossing rails.

Exam trap: Wrong: cross rails at any angle. Right: aim close to a right angle only where legal and safe.

Read the full explanation
  • Conventional road markings may offer less grip than the adjacent surface, especially when wet. You must allow for this at pedestrian crossings, arrows and wide lines.
  • If you have to cross a painted surface lawfully, slow down beforehand and cross smoothly, keeping the motorcycle as upright as you can while following your path. Avoid braking, accelerating or turning sharply on it. Respect the meaning of the marking and pedestrians’ priority, even if this means stopping beforehand.
  • Drain covers and grilles, manhole covers and metal plates can be very slippery when wet. Try to anticipate them without making sudden lane changes. [RGCond, annex V.B.2.2.º d)](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#anv).
  • When crossing rails, aim for an angle close to a right angle when the road layout and traffic allow you to do so safely. Crossing almost parallel to them can trap or deflect a wheel. Aim for that angle within the space where you are allowed to ride, and reduce your speed before the crossing.

9Oil, sand, gravel and leaves

A helmeted rider travels on an upright 125 cc motorcycle in the right-hand lane, approaching an accumulation of sand, gravel, mud and leaves.
The key idea

Spot material on the road early and use your controls gently.

MaterialWhat you must expect
Oil or fuelYou can lose grip
Sand or gravelYour wheels can slide; debris can fly up
Wet leaves or mudYou can find less grip and hidden potholes

Remember

  • Avoid spills only with a small, legal and safe adjustment.
  • If you cannot avoid them, slow down beforehand and limit your lean.
  • Keep a possible path within your lane, including on bends.
  • On sand or gravel, increase your gap behind the vehicle ahead.
  • In mud, choose a gear that avoids wheelspin or straining the engine.
  • If you cannot stay stable, stop trying and seek help from somewhere safe.

Exam trap: Wrong: accelerate to cross oil sooner. Right: slow down beforehand and use the controls gently.

Read the full explanation
  • You must watch for oil or fuel spills, especially at junctions and places where vehicles stop. There is no central or side line that is always free of debris. If you can avoid a spill with a small, lawful and safe adjustment, do so early and without surprising others.
  • If you cannot avoid a slippery area, slow down before reaching it, limit your lean and use the controls gently. Braking sharply on oil or accelerating to cross it quickly can cause a wheel to lose grip. Keep to a viable line within your lane, including when you are cornering.
  • Loose sand and gravel reduce contact with the surface and can make the wheels slide. Increase your distance from the vehicle ahead because of the reduced grip and possible debris being thrown up. Pay particular attention to verges, path entrances, road repairs and bends where materials collect.
  • Wet leaves and mud can hide potholes, markings and edges as well as reduce grip. You must treat a build-up as a hazard even if the rest of the road is dry.
  • In mud, you must choose a gear that delivers power smoothly, without wheelspin or straining the engine. If you cannot maintain stability, do not keep trying; ask for help from a safe position.

10Potholes, joints and roadworks

A helmeted rider travels on an upright 125 cc motorcycle in a straight line towards a small pothole beside roadworks marked by cones.
The key idea

Spot uneven surfaces early and adapt your handling to your vehicle's design.

15 kWMaximum tricycle power with A1
VehicleBehaviour on bends
Two-wheeled motorcycleLeans
Tricycle with a chassis that cannot leanDoes not lean; a wheel can lift

Remember

  • Leave space to spot potholes and joints early.
  • If you feel vibrations after an impact, stop somewhere suitable.
  • Slow down before roadworks and increase your gap.
  • Allow space for your whole motorcycle and body.
  • Roadworks can remain dangerous without workers present.
  • On a tricycle that cannot lean, slow down beforehand and use gentle controls.

Exam trap: Wrong: a tricycle that cannot lean corners like a motorcycle. Right: it cannot lean and can roll over on a fast bend.

Read the full explanation
  • You must look out for potholes, cracks, raised edges and longitudinal joints well in advance. An uneven surface can affect your steering or momentarily unload a wheel. Keep enough distance so that the vehicle ahead does not hide the obstacle until the last moment and you can decide without rushing.
  • An impact with a pothole can damage a tyre, wheel rim or steering: if you notice vibrations or a change in the motorcycle’s response, stop somewhere suitable; how to cross an unavoidable uneven surface is explained in “Slopes and slippery surfaces”, in “Motorcycle riding techniques”.
  • At roadworks you may encounter loose aggregate, milled surfaces, changes in level and narrow lanes. Slow down before the area, increase your following distance and avoid blindly following the line taken by the vehicle ahead. You must assess the space available for your motorcycle and your body, not just for the wheels.
  • The hazard may continue even when you cannot see workers. Observe the temporary layout, surface and obstacles along each section. Allow for less lateral clearance and uneven grip; consult “Traffic signs and their order of priority” to interpret the signs and delineation.
  • With an A1 licence you can ride motor tricycles of up to 15 kW. If you ride one with a non-tilting chassis, it does not lean in bends, unlike a two-wheeled motorcycle. Taking a bend too fast can lift a wheel and cause a rollover. On an adverse camber or when crossing ruts, tram rails or drain covers, the wheels may encounter different levels or levels of grip, affecting steering and stability. Slow down beforehand, use the controls smoothly and also allow for the wind pushing against its bodywork; adapt your handling to its specific design. [RGCond, art. 4.2, A1](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#a4); [RGCond, annex V.B.2.2.º d) and f)](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#anv).

11Rain and wet surfaces

A helmeted motorcyclist rides in the rain on a wet road, leaving a wide gap behind the car ahead.
The key idea

In rain, slow down and increase your gap.

Remember

  • Expect poorer vision and more space needed to stop.
  • Watch for wet patches even after rain stops.
  • After dry weather, the first drops can make roads especially slippery.
  • Brake, steer and accelerate gradually.
  • Do not overtake if spray stops you seeing enough.
  • If you cannot continue, wait somewhere permitted, safe and unlikely to flood.

Exam trap: Wrong: always use only the rear brake in rain. Right: adapt braking to grip and lean angle.

Read the full explanation
  • In rain, you must allow for poorer visibility, less grip and a longer stopping distance at the same time. Reduce your speed and increase your following distance before you need to brake hard.
  • Water running off a slope or access road can keep part of the carriageway wet even after the rain stops. You must detect these local changes before leaning or braking on them; the rest of the route drying does not mean that section has the same grip.
  • The first drops after a dry spell can mix with dust and grease to form a particularly slippery film. You must assess the actual conditions throughout your journey.
  • Brake, turn and accelerate progressively. You must not always avoid using the front brake or assume that using only the rear brake prevents every skid. Adapt the pressure to the grip and lean angle; braking techniques are covered in “Motorcycle riding techniques”.
  • Spray from large vehicles can suddenly block your field of vision. Increase your margin and do not begin an overtaking manoeuvre if you cannot see what you need to.
  • If the rain prevents you from maintaining sufficient visibility or control, find a permitted, safe place off the road to wait. Avoid places liable to flooding and do not use just any arcén (hard shoulder) as a resting place. How to signal that a vehicle is immobilised in an emergency are covered in “Accidents, breakdowns and assistance”.

12Standing water and aquaplaning

A helmeted rider on a 125 cc motorcycle travels in the right-hand lane and approaches a large puddle ahead of the wheels.
The key idea

Standing water can make your tyres lose contact with the road.

Remember

  • Slow down before reaching puddles or standing water.
  • If you lose grip, avoid sudden control movements.
  • Ease off the throttle gently and keep a steady path.
  • Do not enter a flooded road with unknown depth or flowing water.
  • After brakes get wet, test gently at low speed when safe without surprising others.
  • Follow the manual; if brakes still respond poorly, stop and request help.

Exam trap: Wrong: aquaplaning only affects cars. Right: you can experience it on a motorcycle, even with tyres in good condition.

Read the full explanation
  • You can experience aquaplaning, also called hydroplaning, when the tyre cannot disperse enough water and loses effective contact with the road surface. This can also happen on a motorcycle. You must not attribute it only to worn tyres or rule it out because the rain has stopped and puddles remain.
  • The risk depends on your speed, the amount of water, and the tyre’s characteristics and condition, including its pressure. You must slow down before depressions and waterlogged areas.
  • If you notice a loss of contact, avoid operating the brakes, throttle or steering abruptly. Gently ease off the demand for acceleration and try to maintain a steady line until grip returns. Do not try to check the brakes while sliding over water, and do not rely on ABS to clear the water.
  • A puddle can hide its depth, a pothole or a drain grille. Do not enter a flooded road if the depth is unknown or there is a current; find a safe alternative. Using a low gear or a tall motorcycle does not guarantee that you can cross it without losing stability or being swept away.
  • After getting wet, the brakes may temporarily lose effectiveness. When it is safe and without surprising others, check their response at low speed using gentle applications, following the manual. If their response remains abnormal, stop and request assistance.

13Fog, smoke and dust

A helmeted motorcyclist travels in the right lane of a foggy road, leaving a large gap behind the car ahead.
The key idea

In fog, smoke or dust, slow down before you lose vision.

Visibility conditionsWhat you must do
Fog or particles in the airPrefer dipped beam; use fog lights only under their conditions
Thick fog, very heavy rain, heavy snowfall, dense dust or smokeYou can use your rear fog light
Those severe conditions endSwitch off your rear fog light

Remember

  • Increase your gap and keep your visor and other viewing surfaces clean.
  • Do not use the vehicle ahead's lights as your only guide.
  • Prefer dipped beam: main beam can worsen your vision.
  • Do not overtake without enough visibility.
  • If you cannot continue, find a safe alternative.

Exam trap: Wrong: any fog allows your rear fog light. Right: use it in thick fog, very heavy rain, heavy snowfall or dense dust or smoke; switch it off when those conditions end.

Read the full explanation
  • In fog, you can see less and others may detect you later. Its moisture can also wet the road surface and your visor. You must reduce your speed, increase your following distance and keep vision equipment clean, without using the lights of the vehicle in front as your sole guide to the route.
  • In fog or with suspended particles, main beam can reflect light towards you and make it harder to see. Prefer dipped beam and use fog lights in accordance with the conditions for their use. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • Thick fog, very heavy rain, heavy snowfall and dense clouds of dust or smoke justify using the rear fog light; switch it off when they clear to avoid dazzling others. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • Visibility can change within the same patch of fog: a slightly clearer area does not guarantee that you can maintain that pace a few metres later. Keep a margin for the next loss of visibility; apply ‘Speed and stopping distance’ and ‘Keeping a safe gap’.
  • A cloud of smoke or dust can suddenly hide a queue, a junction or an obstacle. Slow down in a controlled way before entering it, avoid overtaking when you cannot see, and find a safe alternative if you cannot continue.

14Snow and ice

A helmeted motorcyclist remains stopped in an asphalt pull-off level with the road, before a patch of ice covering the roadway.
The key idea

Do not continue if snow or ice prevents you from keeping control.

On snow, only if you can proceed safelyHow you should ride
Level groundSlowly and steadily; use a high enough gear without straining the engine
UphillAvoid sudden acceleration; choose a gear that avoids wheelspin or stalling
DownhillControl speed from the start; avoid sudden downshifts and excessive braking

Remember

  • Suspect ice in damp, shaded areas, on bridges and in dips during intense cold.
  • Slow down before suspect areas and avoid sudden movements.
  • Obey restrictions and officers' instructions.
  • Do not automatically follow advice about car snow chains.
  • Check wheel tracks: they can be icy.

Exam trap: Wrong: no visible snow means no ice. Right: you can find icy patches without seeing snow.

Read the full explanation
  • Snow can hide the road layout and reduces grip; ice can cause you to lose your balance with only minimal corrections. On a motorcycle, you must consider avoiding or ending the journey if there is not enough grip. No skill can make up for being unable to maintain contact and control.
  • You must suspect ice on wet, shaded areas, bridges, flyovers and dips, especially after intense cold at night and in the early morning. The absence of visible snow does not prove that the road surface is free of ice patches. Slow down before suspected areas and avoid sudden movements.
  • If you can still ride safely on snow, keep your speed low and steady and use the controls smoothly. On a level stretch, use a sufficiently high gear to apply power gradually without straining the engine.
  • On a snow-covered uphill section, avoid sudden acceleration and unnecessary gear changes; choose a gear that lets you keep moving without wheelspin or stalling. On a downhill section, control your speed from the start, avoiding abrupt downshifts and excessive strain on the brakes.
  • You must obey restrictions and officers’ instructions and choose a safe alternative when you cannot continue. Do not automatically apply advice about fitting chains to a car to your motorcycle. Do not follow tyre tracks without checking them either: compacted snow may be icy.

15Crosswinds and gusts

A helmeted motorcyclist with both hands on the handlebars rides within the right lane while gusts of wind cross the road from left to right and bend a tree in that direction.
The key idea

In crosswinds, slow down and leave space for gentle corrections.

Remember

  • Hold the handlebars firmly without making your arms too stiff.
  • Leave space from edges, vehicles and oncoming traffic.
  • Expect gusts on bridges, in open areas and at tunnel exits.
  • Expect wind changes where buildings, barriers or trees end.
  • Watch for falling objects and other vehicles' movements.
  • If you cannot keep your path with enough space, stop your journey somewhere safe.

Exam trap: Wrong: accelerate to get through a gust sooner. Right: slow down and correct gently.

Read the full explanation
  • A crosswind can push you off your line and force you to correct your balance. You must reduce your speed and keep a margin from the edge of the road, other vehicles and oncoming traffic.
  • Hold the handlebars firmly without tensing your arms and make gentle corrections to maintain your line. Do not take one hand off the handlebars or accelerate to get through a gust more quickly. Adjust your correction to changes in the strength and direction of the wind.
  • Expect gusts on bridges, in open areas, at tunnel exits and beyond barriers, buildings or trees. Also watch for branches and other objects that could fall or enter the road. The danger is not only the force on your motorcycle, but also the movements of other road users.
  • Do not assume the wind is harmless because it is blowing from ahead or behind. Its strength, turbulence and changes of direction also matter. If you cannot maintain your line with enough margin, find a safe place to stop the journey; another motorcycle does not provide reliable protection.

16Large vehicles and wind shielding

A helmeted motorcyclist overtakes an orange truck on the left with ample lateral clearance, while blue lines represent wind coming from the right and flowing around the truck.
The key idea

Near large vehicles, expect sudden changes in wind pressure.

Overtaking a lorry on the left, wind from the rightWhat you must expect
Alongside the lorrySideways wind pressure can suddenly decrease
After passing itYou can face the full wind again

Remember

  • Expect disturbed air when meeting or overtaking a lorry.
  • Adjust gently when sideways wind pressure changes.
  • Do not overtake if wind or space prevents a safe gap.
  • Do not accelerate without considering risks and the speed limit.
  • Consider how your screen, panniers and load change your response to wind.
  • Follow the manufacturer's instructions.

Exam trap: Wrong: move closer to a lorry for shelter. Right: keep your distance and expect changes in wind pressure.

Read the full explanation
  • When approaching a lorry, you must expect turbulence and changes in your exposure to the wind, both when passing it in the opposite direction and when overtaking it. Its size may shelter you briefly, then leave you exposed as you leave its shelter.
  • If the wind is coming from the right and you overtake on the left, the lorry may suddenly reduce the sideways force as you draw level with it. You must gently adjust the correction you were making so that you do not move closer to it. Once you pass it, you may be exposed to the full wind again.
  • Do not begin overtaking if gusts or the available space prevent you from keeping a safe clearance. Increasing your speed indiscriminately leaves you less time to correct and may break the speed limit.
  • The fairing can reduce some of the wind and rain, but its effect depends on its design. Panniers, the windscreen and luggage change the exposed area and may alter how sensitive the motorcycle is to gusts. You must keep a margin and follow the manufacturer’s instructions for use.

17Cold, heat and sun glare

A motorcyclist wearing protective gear drinks water while seated in the shade beside their 125 cc motorcycle parked in a roadside rest area on a sunny day.
The key idea

Adapt your equipment and rest stops to cold, heat and sunshine.

ConditionRisk you must expect
ColdLess feeling and precise control
HeatDehydration, tiredness and sleepiness
Low sunYou can be dazzled; others may not see you

Remember

  • Wear suitable protective clothing with ventilation and a good fit.
  • In cold weather, stop before you lose precise control.
  • In hot weather, rest and drink water during stops.
  • With low sun, use suitable eye protection and slow down before losing vision.
  • Do not use a very dark visor at night or in poor light.
  • Check your condition after a heavy meal or an exhausting day.

Exam trap: Wrong: drink alcohol to fight the cold. Right: wear suitable equipment and recover somewhere sheltered.

Read the full explanation
  • In cold weather, you may lose feeling in your hands and feet and operate the controls less effectively. You must wear suitable clothing and plan stops to recover in a sheltered place. Do not keep riding until stiffness or shivering prevents you from controlling the motorcycle precisely; alcohol does not help you cope with the cold.
  • In hot weather, you may tire sooner and suffer dehydration, reduced attention and drowsiness. Plan breaks, drink water during stops and avoid the most demanding hours when possible.
  • Choose protective clothing that allows adequate ventilation without sacrificing strength or fit. Flapping garments can distract you and increase your effort.
  • Low sun can dazzle you at sunrise, sunset or when leaving a bend. Use eye protection suitable for riding and reduce your speed before you lose visibility. Remember that a driver approaching the sun may also have difficulty detecting your motorcycle.
  • You must avoid a very dark visor at night or in poor light and comply with its restrictions on use. A scratched or dirty visor scatters light and worsens glare. Clean and maintain your visor and mirrors; maintaining good vision matters in sunshine as well as in rain.
  • Avoid starting the return journey after a large meal or an exhausting day without assessing your condition. Heat, digestion and accumulated sleep loss can combine even on a short journey. Plan water and places to rest before setting off, and adapt your plan if signs of drowsiness appear.

18Night riding and range of vision

A helmeted rider travels at night in the right lane on a 125 cc motorcycle, whose headlight illuminates a fallen branch ahead and the stretch of road between them.
The key idea

At night, adapt your speed to the space you can actually see.

Remember

  • Stay alert even when there is little traffic.
  • Adapt your speed when entering a dark area.
  • Do not stare at bright lights.
  • Slow down when switching to dipped beam if you lose viewing distance.
  • Before a bend, adjust your speed and allow space for your body.
  • To overtake, you need to see space for the whole manoeuvre.

Exam trap: Wrong: keep main beam on while someone overtakes you. Right: switch to dipped beam as soon as you could disturb their driver.

Read the full explanation
  • At night, it is harder to recognise people, obstacles, distances and changes in the road surface. You must pay more attention even when there is little traffic. An empty road does not guarantee that you will see an animal, a patch on the road or a stopped vehicle in time, and tiredness can build up without you noticing. [DGT, night riding](https://revista.dgt.es/es/reportajes/2022/02FEBRERO/0214-Consejos-Conducir-Noche.shtml).
  • When moving from a lit area to a dark one, your eyes need time to adjust. Avoid keeping a speed chosen for the previous stretch and do not stare at bright lights.
  • When switching from main beam to dipped beam, the shorter range of the beam gives you less time to anticipate; apply the duty to adapt your speed explained in ‘Speed and stopping distance’.
  • On a bend, the beam may illuminate less of the path you will follow and may hide how the bend tightens. Adjust your speed beforehand and keep a margin within your lane, including for your body as you lean.
  • If you are going to overtake at night, you need to see the space required for the whole manoeuvre and avoid dazzling the vehicle in front through its mirrors. If you are being overtaken, adapt your lights as the other vehicle passes. Switch to dipped beam as soon as the beam’s range could trouble its driver.

19Lights and dazzle at night

A helmeted rider travels on a 125 cc motorcycle with dipped headlights along a road at night as a car approaches in the opposite lane, both with their beams directed at the asphalt.
The key idea

Use main beam when required and switch to dipped beam if you could dazzle someone.

40 km/hMain beam threshold: above this
Insufficiently lit locationMain beam, unless dipped beam is required
Outside built-up areas at nightYou must use it above 40 km/h
Tunnels, underpasses and stretches marked as tunnels, at any timeYou must use it above 40 km/h

Remember

  • Switch straight to dipped beam if you could dazzle someone.
  • You can also dazzle drivers through their mirrors.
  • If dazzled, slow down as needed, even to a stop.
  • Avoid looking directly at the light source.
  • With a passenger or luggage, check your headlamp's direction.
  • Keep lights clean and adjust your headlamp following the manufacturer's instructions.

Exam trap: Wrong: main beam is compulsory only at night. Right: also use it above 40 km/h in insufficiently lit tunnels, underpasses and stretches marked as tunnels, unless dipped beam is required.

Read the full explanation
  • You must use main beam above 40 km/h outside built-up areas, at night and on inadequately lit roads; also above 40 km/h at any time in inadequately lit tunnels, underpasses and sections marked «Tunnel» (S-5), unless dipped beam is required, especially to avoid dazzling others. See «Motorcycle lights and signals» for the full use of lighting. [RGC, art. 100.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100).
  • You must switch from main beam to dipped beam as soon as there is any possibility of dazzling someone, including through their mirrors. On bends, consider the direction of the beam; you must not keep main beam on simply because the other vehicle still seems far away. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102).
  • If you are dazzled, slow down as much as necessary, even to a stop. Do not respond with main beam or accelerate through an area you cannot see. Avoid looking directly at the light and use safe references to guide your path. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102).
  • Check that the headlamp remains correctly aligned when you carry a passenger or luggage, and keep the lighting equipment clean. A beam that is too low reduces your range; one that is too high can bother others. Adjust it according to the manufacturer’s instructions.

20Speed and stopping distance

A motorcyclist wearing a helmet and protective gear rides a lightweight motorcycle in the right lane before a right-hand bend with wet pavement.
The key idea

Choose a speed that lets you stop within the space you can see.

SituationWhat you must remember
You exceed the permitted limitYour speed is excessive
You lack safety space for conditionsYour speed is inappropriate
Slippery surfaceYou mainly need more braking space
Tighter bend, same speed and comparable conditionsYou need more inward lean

Remember

  • You can ride too fast even within the speed limit.
  • Stopping distance adds reaction distance and braking distance.
  • At higher speed, you travel further while reacting.
  • Tiredness can make you react more slowly.
  • Slow down before bends and keep some grip in reserve.
  • When leaning, allow space for your motorcycle and your body.

Exam trap: Wrong: any speed below the limit is safe. Right: slow down further if conditions require it.

Read the full explanation
  • Speeding means exceeding the permitted limit; an inappropriate speed leaves too little margin for the conditions. You can obey the maximum and still travel too fast for a wet bend, limited visibility or your level of tiredness. You must adjust your speed so that you can stop within the area you can see and for obstacles that may appear. Slow below the maximum when safety requires it; see the limits in «Speed and distances on a motorcycle». [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45).
  • At higher speeds, you travel further while perceiving and reacting, and need more distance to brake. Total stopping distance is the sum of reaction distance and braking distance. A light motorcycle is not guaranteed to stop in a shorter distance than any car, especially with poor grip or poorly controlled braking.
  • At the same speed, if fatigue makes you slower to react, your reaction distance increases. A slippery road surface mainly increases the distance needed to brake, if all other conditions remain the same.
  • At higher speeds, you also have less time to interpret signs, entrances and lateral movements. The so-called tunnel effect refers to a reduction in your useful field of vision, not to the name of fatigue. Accelerating to finish a demanding journey sooner increases your workload.
  • On a bend, higher speed and a smaller radius increase the demands of turning. Slow down beforehand and avoid entering without a reserve of grip. Braking sharply while the motorcycle is leaning can exceed the available grip.
  • On a tighter bend, at the same speed and in comparable conditions, you need to lean further towards the inside. When leaning, allow for the space taken up by the whole motorcycle and your body, including your head. Slow down beforehand to keep a margin from oncoming traffic and obstacles.
  • A bend that tightens can use up the grip margin you allowed for on entry; practical guidance is given in «Follow your line and complete the turn», in «Motorcycle riding techniques».

21Keeping a safe gap

A helmeted rider travels on a 125 cc motorcycle along a wet road, leaving a wide gap behind an orange car in the same lane.
The key idea

Leave enough space to stop if the vehicle ahead brakes suddenly.

Remember

  • Adapt your gap to speed, grip and braking.
  • You also need space in towns and queues.
  • Leave more space in rain, on gravel, with poor visibility or uneven surfaces.
  • With a passenger or luggage, adapt speed and gap to your motorcycle's behaviour.
  • Before using a sideways escape route, check its surface and obstacles.
  • Do not assume your motorcycle's balance prevents every fall.

Exam trap: Wrong: ABS lets you follow more closely. Right: it does not create grip on oil, ice or standing water.

Read the full explanation
  • You must leave enough distance to stop without colliding if the vehicle in front brakes sharply. Adjust that gap to your speed, grip and braking; you also need it in towns and in traffic queues. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54).
  • You must increase your margin in rain, on gravel, with reduced visibility or on an uneven surface. Carrying a load or passenger also means reconsidering it because the motorcycle behaves differently.
  • ABS helps reduce wheel lock, but it does not create grip on oil, ice or standing water. Do not shorten your gap because you have it. The gyroscopic effect also does not keep the motorcycle balanced in every situation or prevent falls when braking or turning at low speed.
  • A seemingly clear space to the side may end at a kerb, a cover or gravel. Before treating it as an escape route from a rear-end collision, also assess its grip and whether you could remain stable; having enough width does not guarantee you can use it on your motorcycle.
  • A passenger and luggage change mass, inertia and weight distribution, and can increase braking distance. They do not always improve grip or, by themselves, increase your reaction time. Adjust speed and spacing to how the motorcycle actually behaves; see «Passengers and loads on motorcycles» for positioning and limits.

22Group riding: organise without pressure

Three helmeted motorcyclists ride in single file to the right, spaced apart, with a green motorcycle between two riders wearing orange jackets on a rural road.
The key idea

Organise your group so nobody has to ride beyond their abilities.

Remember

  • Agree on your route, breaks and safe meeting points.
  • Adapt the pace to the least experienced rider and least capable motorcycle.
  • Always follow the rules and what the road permits.
  • Say when you need to stop and use your own judgement.
  • Avoid racing, showing off or overtaking companions in ways that disrupt the group.
  • Handle each traffic light, priority situation and overtake individually.

Exam trap: Wrong: accelerate if you lose the group. Right: follow your agreed meeting plan.

Read the full explanation
  • Before setting off, agree the route, rest stops and safe regrouping points. You must know what to do if someone gets separated, without relying on chasing them. If the group is large, splitting it into smaller groups with space between them can make riding easier and reduce pressure.
  • You must adapt the pace to the least experienced rider and the motorcycle with the lowest capacity, within what the road and rules permit. If you ride with more powerful motorcycles, you do not have to push your A1 to keep up: agree a suitable pace and meeting points.
  • Pressure to maintain visual contact with your companions can make you delay a break or accept an excessive pace: say when you need to stop and make your own decisions about the journey.
  • You must avoid showing off, racing and overtaking between companions in ways that disrupt the group. If you lose the group, follow the regrouping plan and do not speed up to catch it. Deal with a traffic light, priority rule or overtaking manoeuvre individually, even if this breaks up the ride.

23Group riding: position and spacing

Three helmeted motorcyclists ride in a staggered formation with longitudinal spacing in the right lane of a straight rural road.
The key idea

In a group, keep your distance and make your own decisions.

Remember

  • Avoid riding too close together.
  • On bends, choose your path using your own view and the surface.
  • Leave space for other vehicles to move between riders safely.
  • Assess every overtake yourself.
  • Check visibility, distance and space to return to your lane.
  • Do not block junctions or close gaps to keep your group together.

Exam trap: Wrong: follow another rider into an overtake because they can complete it. Right: check your own safety space.

Read the full explanation
  • A formation that is too compact reduces your chances of avoiding an obstacle and encourages a series of rear-end collisions; the arrangement of the motorcycles is explained in «Ride in a group without competing», in «Motorcycle riding techniques».
  • On a bend, your companion’s position may lead you towards a patch or the edge of the lane if you try to copy it: choose your own margin according to the road surface and the visibility from your motorcycle.
  • A group that continuously occupies all the available space makes it difficult for other vehicles to join safely; see «Space to allow overtaking», in «Speed and distances on a motorcycle», for the additional gap and its exceptions. [RGC, art. 54.2 and 3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54).
  • You must not follow another motorcyclist into an overtaking manoeuvre without making your own assessment of visibility, distance and room to return. They may complete it and leave no room for you. You must also not block junctions or close gaps to keep the group together; regroup safely at the planned place.

24Fatigue and sleep on a motorcycle

A motorcyclist rests with eyes closed on a bench, with their helmet beside them and their motorcycle parked in a space off the road.
The key idea

If you feel tired or sleepy, stop before you lose control.

2 hoursGeneral rest advice; motorcycles: sooner
200 kmIf sooner; motorcycles: shorten interval
Signs you noticeWhat you must recognise
Stiffness, muscle discomfort, distraction or late correctionsYou may be tired
Yawning, heavy eyelids or incomplete memoriesYou may be sleepy; do not wait for more signs

Remember

  • Set off rested and plan breaks.
  • Take earlier breaks in cold, heat, darkness or difficult conditions.
  • Stop before your planned break if your riding gets worse.
  • Use whichever general rest limit comes first; on motorcycles, take breaks sooner.
  • Find a permitted, safe place to rest.
  • If sleepy, sleep and continue only when you can ride safely.

Exam trap: Wrong: coffee replaces rest. Right: it can hide symptoms but does not remove your need to rest.

Read the full explanation
  • Riding a motorcycle requires physical and mental effort: maintaining your posture, coping with wind and cold, and constantly focusing on balance can make you tired. Fatigue reduces attention and precision, encourages distraction and lengthens reaction time. [DGT, fatigue, 10-07-2019](https://revista.dgt.es/es/noticias/nacional/2019/07JULIO/0710Estudio-fatiga.shtml).
  • Stiffness, muscle aches, difficulty concentrating and late corrections are signs of fatigue. Sleepiness adds yawning, heavy eyelids, incomplete memories of the journey and possible microsleeps. If your path changes involuntarily or you cannot remember the road you have just travelled, do not wait for more symptoms to confirm it.
  • Rest before the journey and plan breaks, bringing them forward in cold or hot weather, at night or in difficult conditions. You must stop before the planned break if you notice your condition deteriorating, even if you are close to your destination.
  • As general preventive advice, the DGT recommends resting every 2 hours or 200 km, whichever comes first; for motorcycle journeys, it recommends shortening that interval. [DGT, fatigue, 10-07-2019](https://revista.dgt.es/es/noticias/nacional/2019/07JULIO/0710Estudio-fatiga.shtml).
  • If you are tired, find a permitted and safe place to stop and rest as soon as possible. If you are sleepy, you need to sleep; do not set off again until you can ride safely. See «Your fitness to drive safely» for more on sleepiness, medicines and other personal factors that can make it worse.
  • Opening your visor, playing music, drinking coffee or using stimulants can mask symptoms without meeting your need for rest.

25Inexperience and risks from other road users

A helmeted motorcyclist rides a 125 cc motorcycle leaving a wide gap behind a cyclist on a two-way road.
The key idea

Give other road users time and space, and expect mistakes.

Road user or vehicleWhat you must expect
Children, older people, people with impaired sight, hearing or mobilityThey may need longer to notice you or react
Cars and vansYou can be hidden in their blind spots
Lorries and busesAlso allow for their size, turns and wind changes

Remember

  • Do not pressure someone who hesitates or changes direction unexpectedly.
  • Expect mistakes from cyclists and moped riders too.
  • Slow down when pedestrians are on the road or may enter it.
  • Stop if circumstances require it.
  • Do not assume apparent experience guarantees a correct response.

Exam trap: Wrong: everyone notices you and reacts equally quickly. Right: some people need more time.

Read the full explanation
  • Another road user's inexperience can lead to hesitation, braking or unexpected changes of direction. Give them time and space without pressuring them with your motorcycle. Also anticipate mistakes by cyclists and moped riders; apparent experience does not guarantee a correct response. [RGCond, Annex V.B.1, subjects 8 and 9](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#anv).
  • When you encounter children, older people or people with difficulties seeing, hearing or moving, allow for the possibility that they may take longer to notice you or react. Reduce your speed and stop if circumstances require it when there are pedestrians on the road or they are likely to enter it. [RGC, art. 46.1.a](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46).
  • With cars and vans, allow for the possibility that your motorcycle may be hidden in their blind spots; with lorries and buses, also allow for their size, turns and changing exposure to the wind. Apply the guidance in “Other vehicles’ blind spots” and “Large vehicles and wind shielding” to maintain a safety margin. [RGCond, Annex V.B.1, subject 9](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#anv).

26Risks when riding through tunnels

A helmeted motorcyclist rides in the right lane of a tunnel, leaving a large gap behind the car ahead.
The key idea

In tunnels, adapt your speed and leave space to react.

Remember

  • Expect changes in light and grip when entering and leaving.
  • Adapt your speed to the space you can see.
  • Do not stare at lights.
  • Expect wind gusts at the exit.
  • Keep the specific gap required in tunnels.
  • Obey traffic lights, information panels and loudspeaker instructions.

Exam trap: Wrong: follow closely in a tunnel. Right: the vehicle ahead can hide a queue and leave you too little space to react.

Read the full explanation
  • When entering and leaving a tunnel, you may encounter sudden changes in light and grip. Adjust your speed to the distance you can see and avoid staring at lights. As you leave, anticipate the gusts described in “Crosswinds and gusts”. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45).
  • In a tunnel, being too close to the vehicle in front can hide a traffic queue from you and reduce your response margin; apply the specific following distance in “Tunnels and underpasses”, in “Speed and distances on a motorcycle”. [RGC, art. 95.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95).
  • You must obey the traffic lights, signs and public-address instructions in the tunnel. Consult “Motorcycle lights and signals” for lighting, and “Accidents, breakdowns and assistance” for what to do in an emergency inside the tunnel. [RGC, art. 95.7](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95).

Crossing a low-grip surface

Prepare before asking the tyre for grip.

  1. Look out for wet road markings, metal, oil, sand or loose gravel, and check the traffic around you.
  2. Slow down beforehand and decide whether you can avoid the area by taking a legal and safe line.
  3. If you have to cross it, keep your lean to what the route allows and use the throttle, steering and brakes smoothly.
  4. Leave room within your lane and only increase demands once you reach a suitable road surface.

Responding to reduced visibility

Adjust your speed to the distance you can actually see.

  1. Look out for fog, spray, darkness, glare or a misted visor, and also check the traffic behind you.
  2. Slow down in a controlled way, increase your following distance and use the appropriate lights without dazzling others.
  3. Make sure you can stop within the distance you can see, and slow down further if you cannot.
  4. If you cannot continue safely, find a permitted, safe place off the road and wait until conditions improve.

Deciding what to do when tired on a ride

When you need a rest depends on how you feel, including when you are riding in a group.

  1. Recognise poor concentration, stiffness, yawning or involuntary changes in pace.
  2. Stop trying to keep up with the group and find a permitted, safe place.
  3. Stop and rest; if you are sleepy, sleep before considering whether to continue.
  4. Reassess your ability and the rest of the journey; continue only if you can ride safely, or find another alternative.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1Which of these situations requires particular care because of potentially low grip when riding a motorcycle?
2On a conventional road outside a built-up area, with two-way traffic, no physical separation and no specific posted limit, the shoulder is 1 metre wide. What is the general speed limit for a motorcycle?
3According to WHO, worldwide, how important are road traffic injuries in mortality among people aged 5–29?
4What aerodynamic function does a fairing properly designed for a motorcycle perform?

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module