Theory · C Licence - Truck · Module 9 of 18

Lorry lights and signals

You learn to choose your lorry’s lighting according to the road, visibility and its situation, avoiding dazzle and correctly signalling manoeuvres and immobilisation. You master the thresholds for side-marker lamps and end-outline marker lamps, the connected V-16, and lorry plates and markings.

40 min read25 sectionsReviewed Nov 3, 2026
A rigid truck travels rightward in its lane at dusk, with headlights, position lamps, side marker lamps and clearance lamps illuminated on a rural road.
See and be seen without dazzling

1Seeing, being seen and warning others

A rigid truck travels in the right lane of a road at dusk, with its headlights illuminating the roadway and its position, clearance and side marker lights on.
The key idea

Use your lights to see, be seen and warn others.

1.60 mTrailer: front position lights above
2.10 mTrailer: end-outline marker lights above
6 mTrailer: side markers above this
LightsPurpose
Dipped and main beamHelp you see the road
Position lights and end-outline marker lightsShow your vehicle
IndicatorsShow where you intend to move

Remember

  • Check the equipment on your lorry and trailer.
  • Keep all equipment required for your vehicle, even when you travel empty.
  • Having a light fitted does not mean you must always switch it on.

Exam trap: Wrong: You must always use fitted rear fog lights. Right: Use them only in particularly poor visibility.

Read the full explanation
  • Your lighting serves three purposes: to illuminate the carriageway, show the presence and dimensions of your lorry, and communicate your manoeuvres or a hazard. Dipped beam and main beam let you see; position lights and end-outline marker lamps let others recognise your vehicle; indicators signal the direction in which you intend to move. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Your lorry must have dipped beam, main beam, reversing lights, indicators with hazard warning lights, brake lights, front and rear position lights, rear fog lights and rear number plate lighting. You must also fit the side marker lights and end-outline marker lamps required by its dimensions; the equipment requirements apply whether you travel laden or empty. [RGV, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • Rear fog lights are compulsory equipment on your lorry, but you may only use them when visibility is particularly poor; front fog lights are optional and their use is also subject to conditions. [RGV, art. 17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a17). [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • You must retain the devices required by your vehicle’s specific type approval. The general table in the regulations refers to vehicle categories and their technical rules: you must not use a general indication that equipment is optional to remove a device that your lorry must have. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15). [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • If you tow an ordinary trailer, you must also check its equipment: indicators with hazard warning lights, brake lights, rear position lights, rear fog lights, number plate lighting and reflectors. It must have front position lights if it exceeds 1.60 m in width, end-outline marker lamps if it exceeds 2.10 m in width, and side marker lights if it exceeds 6 m in length. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).

2When you must switch on your lights

A box truck travels in its right-hand lane with its headlights on at night along a street lit by street lamps in a Mediterranean town.
The key idea

Switch on your lights when the time, place or visibility requires them.

10 mRead a number plate
50 mSee a dark vehicle

Remember

  • Use your lights from sunset to sunrise.
  • Use them in tunnels and underpasses, even during the day.
  • Use lights when fog, heavy rain, snow, smoke or dust significantly reduces visibility.
  • Treat lighting as insufficient if you cannot meet either distance test.

Exam trap: Wrong: Street lamps let you drive at night without lights. Right: You must use lights.

Read the full explanation
  • You must use the appropriate lighting from sunset to sunrise. This requirement applies both inside and outside built-up areas; street lighting determines which driving lights you must use, but does not allow you to drive at night without lights. [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98).
  • You must also switch on your lights during the day in tunnels, underpasses and stretches covered by the tunnel sign. Daylight visible at the other end does not remove this requirement, nor does the artificial lighting installed inside the tunnel or underpass replace it. [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98).
  • If fog, heavy rain, snowfall or clouds of smoke or dust significantly reduce visibility, you must use the required lighting even at midday. Assess the actual visibility: you do not need to wait until nightfall to make your lorry’s load body visible. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • You must consider a road insufficiently lit if, with normal eyesight, at any point you cannot read a number plate at 10 m or distinguish a dark vehicle at 50 m. Either circumstance is enough; these are lighting criteria, not distances for switching from main beam to dipped beam. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100).

3Position lights: presence and width

A truck travels at night in its right-hand lane on a two-way road with its white position lamps, clearance lamps and dipped headlights switched on.
The key idea

Use position lights to show your lorry’s presence and width.

2.10 mEnd-outline marker lights required above
Lorry position lightsColour
FrontWhite
RearRed

Remember

  • Keep position lights on at night, in tunnels, and when visibility drops significantly.
  • Add the lights you need for driving.
  • Keep position lights on with dipped beam, main beam or front fog lights.

Exam trap: Wrong: You can drive at night with only position lights. Right: Add the required driving lights.

Read the full explanation
  • Your lorry must have two white front position lights and two red rear position lights, located towards the outer edges in accordance with the installation requirements. They show its presence and width; you must not confuse them with white dipped-beam headlights or red brake lights. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must keep the position lights on when driving at night, in tunnels and underpasses, or when visibility is significantly reduced. If the width exceeds 2.10 m, you must also keep the end-outline marker lamps on. In these circumstances, position lights form part of the lighting you use; they do not replace the headlights you need. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99).
  • At night you must use dipped beam or main beam as well as position lights, depending on the road. In the special conditions set out in article 106, you may use front fog lights together with position lights. [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101). [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • You must use front position lights together with dipped beam, main beam or front fog lights; rear position lights come on automatically with the lighting specified in the regulations. The technical exception for brief light signals does not authorise you to drive without position lights when they are compulsory. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15).

4Side marker lights: the 6 m threshold

A long rigid truck travels to the right in its lane, with five amber side marker lights distributed along its side, in a Mediterranean landscape.
The key idea

Check your lorry’s length to find out whether you need side marker lights.

6 mRequired above this length
DeviceMeasurement to check
Side marker lightsLength
End-outline marker lightsWidth

Remember

  • Your complete lorry needs side marker lights above this length.
  • Remember the exception for chassis-cabs.
  • Expect amber as the usual colour.
  • A red side light may be combined with certain rear devices.
  • Check how many lights your lorry needs for its length.

Exam trap: Wrong: Exactly 6 m requires side marker lights. Right: You must exceed that length.

Read the full explanation
  • If your complete lorry exceeds 6 m in length, it must have side marker lights. The stated exception applies to chassis-cabs. At exactly 6 m, you do not exceed the threshold; on motor vehicles up to that length, fitting them may be optional. [RGV, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, art. 17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a17).
  • Side marker lights emit amber light and are distributed along the side of the vehicle. The general table specifies a minimum of two and a maximum depending on length, with installation according to the vehicle category; you must not assume that any long lorry is correctly equipped with just two lights. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You may see a red side light under the regulatory exception for grouping, combining or incorporating it with certain rear lighting devices. You must learn amber as the general rule without treating every red device near the rear that meets this exception as incorrect. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must relate side marker lights to length and end-outline marker lamps to width. A lorry 7 m long and 2 m wide needs side marker lights, while end-outline marker lamps are optional at that width. These devices serve different purposes, and you must check both criteria separately. [RGV, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, art. 17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a17).

5End-outline marker lamps: the 2.10 m threshold

A wide truck travels in its lane on a two-way road with two white width marker lamps lit at its upper front outer corners and its lower lights illuminated.
The key idea

Use end-outline marker lights to show your lorry’s full width.

2.10 mRequired above this width
1.80 mOptional range starts here
Lorry widthEnd-outline marker lights (rear optional on chassis-cabs)
1.80 to 2.10 mOptional
Over 2.10 mRequired

Remember

  • Recognise the high lights: white at the front and red at the rear.
  • Use them to supplement your front and rear position lights.
  • Rear end-outline marker lights are optional on chassis-cabs.
  • Do not use these lights to judge your lorry’s height.

Exam trap: Wrong: Exactly 2.10 m requires end-outline marker lights. Right: You must exceed that width.

Read the full explanation
  • If your lorry exceeds 2.10 m in width, it must have end-outline marker lamps: two lights visible from the front and two from the rear. They emit white light at the front and red light at the rear; their location near the outer edges and as high as possible helps others judge the vehicle’s overall size. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • If the width is between 1.80 and 2.10 m, end-outline marker lamps are optional. Exactly 2.10 m is not the same as exceeding 2.10 m; a lorry 2 m wide is not required to have them because of its width. Rear end-outline marker lamps are optional on chassis-cabs. [RGV, art. 17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a17). [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • End-outline marker lamps supplement front and rear position lights to show your lorry’s overall size. Their arrangement is particularly useful for identifying the upper edges of a wide load body in the dark. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • End-outline marker lamps and signs restricting clearance height serve different purposes. In vehicle lighting, end-outline marker lamps indicate overall width in particular and supplement position lights; their presence does not indicate your lorry’s exact height or guarantee that you can drive under a bridge. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).

6Dipped beam: lighting the road ahead

A truck travels in its lane on an urban street at night, with its two white dipped headlights on and illuminating the nearby road beneath the streetlights.
The key idea

Use dipped beam to light the nearby road without dazzling others.

40 km/hDipped without main: maximum speed
Poorly lit interurban road at nightWhat you should use
No main beam availableDipped beam
Risk of dazzling othersDipped beam
Up to 40 km/h without main beamYou must use dipped beam

Remember

  • Use dipped beam at night in built-up areas, even on dark roads.
  • Use it at night outside built-up areas on sufficiently lit roads.
  • Change to dipped beam if you could dazzle others.
  • Keep position lights on with dipped beam.

Exam trap: Wrong: Dipped beam requires rear fog lights. Right: Rear fog lights need particularly poor visibility.

Read the full explanation
  • Your lorry must have two white dipped-beam headlights at the front. You must use them to light the road immediately ahead without dazzling others; the name dipped beam does not mean you can do without them because street lights illuminate the road well. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx). [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101).
  • At night you must use dipped beam on urban roads and sufficiently lit interurban roads. You must also use it within built-up areas when lighting is insufficient: darkness on a stretch of road through a town does not authorise you to use main beam there as your normal driving lighting. [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101).
  • On an insufficiently lit interurban road, you must use dipped beam when you have no main beam, when you could dazzle others, or when you drive at a speed not exceeding 40 km/h without using main beam. At exactly 40 km/h, if you do not use main beam, you must use dipped beam. [RGC, art. 101.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101).
  • You must keep the position lights on together with dipped beam and check the rear number plate lighting where required. Switching on dipped beam does not require you to switch on the rear fog lights: these remain subject to their specific condition of particularly poor visibility, even though both types of light can operate at the same time. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15). [RGC, art. 103](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a103). [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).

7Main beam: range and limits

A truck travels in its right-hand lane on a rural road at night, with white high-beam headlights on and three amber side marker lights on its cargo box.
The key idea

Use main beam only where allowed, without dazzling others.

40 km/hRequired speed must exceed this

Remember

  • At night, use main beam outside built-up areas on dark roads above 40 km/h.
  • Use it only when dipped beam is not required, especially to avoid dazzle.
  • Keep position lights and all other required lights on.
  • Switch main beam off when you stop or park.

Exam trap: Wrong: Exactly 40 km/h requires main beam. Right: You must exceed that speed.

Read the full explanation
  • Your lorry must have white main-beam headlights, with an even number of lights as required by its category and type approval. Their purpose is to illuminate the road further ahead; you must avoid fitting additional spotlights on your own initiative unless they meet the authorised installation requirements. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15). [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must use main beam at night outside built-up areas on inadequately lit roads when you drive at more than 40 km/h and are not required to use dipped beam, particularly to avoid dazzling others. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100).
  • You may use main beam without dipped beam or together with it when its use is permitted. Using main beam on its own means without dipped beam; you must keep the position lights and any other required lights on. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100). [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15).
  • You must not keep main beam on when your vehicle is stopped or parked. You must also not alternate between main beam and dipped beam for purposes other than permitted warnings; brief flashes permitted by the regulations have their own conditions, and you must always avoid dazzling others when using them. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100). [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).

8Avoiding and dealing with dazzle

A truck and a car approach each other at night in their respective lanes with dipped headlights directed toward the road surface.
The key idea

Change to dipped beam as soon as you could dazzle anyone.

Remember

  • Do not wait for the other driver to dip their headlights.
  • Avoid dazzling oncoming drivers or drivers ahead through their mirrors.
  • Wait until you pass an oncoming vehicle before restoring main beam.
  • Slow down if you are dazzled.
  • Stop if you need to avoid an accident.

Exam trap: Wrong: Always dip at a fixed distance. Right: Dip as soon as you could dazzle anyone.

Read the full explanation
  • You must switch from main beam to dipped beam as soon as you notice any possibility of dazzling others. You must also do so if the other driver keeps their main beam on: your obligation does not depend on them acting correctly. This provision does not set a universal switching distance for every encounter. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102).
  • You must avoid dazzling oncoming drivers and drivers ahead who receive your lights through their mirrors. The rule also protects users of other transport routes; you must assess the effect of the beam even if they are not in your lane. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102).
  • When meeting another vehicle, you must not switch main beam back on until you have gone past it. If you follow a car in your lorry, you must keep dipped beam on while your main beam could reach its mirrors; the height difference between the vehicles does not remove the risk. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102).
  • If you are dazzled, you must reduce your speed as much as necessary, even to a complete stop, to avoid hitting vehicles or pedestrians. You must not continue by relying on your memory of the road layout or respond with main beam; you need to regain a sufficient field of vision before moving on. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102).

9Tunnels and underpasses

A truck drives towards a well-lit tunnel during the day with its dipped headlights and upper clearance lights on.
The key idea

Enter tunnels with the required lights on, even during the day.

2.10 mEnd-outline marker lights required above
40 km/hInterurban main beam speed threshold
TunnelDriving lights
Well litPosition lights and dipped beam
Poorly litApply the conditions for dipped and main beam

Remember

  • Use position lights and dipped beam in a well-lit tunnel.
  • Light the rear number plate too.
  • Use dipped beam in built-up areas.
  • If traffic stops, temporarily use hazard warning lights and keep position lights on.
  • If you break down inside, use hazard warning lights and keep position lights on.

Exam trap: Wrong: Every tunnel requires main beam. Right: Check lighting, built-up area, speed and dazzle.

Read the full explanation
  • You must enter with the required lights on at any time of day, even if the tunnel is short or brightly lit. In a sufficiently lit tunnel, you must use position lights and dipped beam; also switch on the end-outline marker lamps if the width exceeds 2.10 m, and illuminate the rear number plate. [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98). [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99). [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101). [RGC, art. 103](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a103).
  • In an inadequately lit tunnel, you must apply the conditions for main beam and dipped beam: outside built-up areas, at more than 40 km/h, you must use main beam if it does not dazzle others and dipped beam is not required. In built-up areas, you must use dipped beam; you must not summarise the rule by saying that every tunnel requires main beam. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100). [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101).
  • If you stop because of traffic inside a tunnel or underpass, you must temporarily switch on your hazard warning lights and keep the position lights on. You study the procedure for traffic queues in «Accidents, breakdowns and first aid», in the section «Breakdown, fire and traffic queues in tunnels». [RGC, art. 97.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a97).
  • If your vehicle is immobilised by a breakdown or another emergency inside a tunnel, you must switch on your hazard warning lights and keep the position lights on. You learn about protection, raising the alarm and assistance in «Accidents, breakdowns and first aid». [RGC, art. 97](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a97).

10Daytime: dipped beam and daytime running lights

A goods truck approaches a tunnel in daylight in its right-hand lane with its dipped-beam headlights on.
The key idea

Check when you need dipped beam: daytime running lights cannot replace it.

LightsWhat you need to remember
Daytime running lightsMake you visible during the day
Dipped beamRequired in the specified situations

Remember

  • Driving a lorry does not require dipped beam throughout every clear day.
  • Use at least dipped beam in reversible lanes and temporary additional lanes.
  • Use it also in lanes opened against the normal direction.
  • Check whether your lorry is allowed to enter the lane.
  • Do not assume daytime running lights switch on your rear lights.
  • Check your lights when entering tunnels or when visibility drops significantly.

Exam trap: Wrong: Automatic light controls always suffice. Right: Check that your required lights are on.

Read the full explanation
  • Driving a goods lorry of more than 3,500 kg does not place you under a general obligation to drive with dipped beam on throughout a clear day. You must switch it on in the specific situations involving tunnels, special lanes and visibility set out in the regulations. [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98). [RGC, art. 104](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a104). [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • You must use at least dipped beam, by day and by night, when driving in a reversible lane, a temporary additional lane or a lane opened to traffic travelling in the opposite direction to normal. This also applies to adjacent lanes carrying traffic in the normal direction under the conditions in article 41. Daytime running lights do not replace this compulsory dipped beam. [RGC, art. 104](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a104).
  • You must not interpret the lighting requirement as permission to enter any special lane with your lorry. Lanes opened to traffic in the opposite direction to normal to improve traffic flow have vehicle restrictions; different rules apply at roadworks. You must first check whether your vehicle is authorised to use them. [RGC, art. 41](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41).
  • Daytime running lights are two white front lights intended to make your vehicle visible during the day. Their installation and automatic operation depend on the applicable type-approval regulations; you must not assume that all lorries have the same equipment regardless of their age. [UN Regulation 48](https://www.boe.es/buscar/doc.php?id=DOUE-L-2021-81325).
  • You must not rely solely on seeing light ahead or an illuminated instrument panel: daytime running lights do not guarantee that the rear lights are on. When you enter a tunnel or visibility is significantly reduced, check that you have selected the required lights, even if you have an automatic lighting control. [UN Regulation 48](https://www.boe.es/buscar/doc.php?id=DOUE-L-2021-81325). [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98). [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).

11Front fog lights: permitted use

A truck travels in its lane on a road in dense fog with its two white front fog lights and dipped headlights switched on.
The key idea

Use front fog lights only in permitted conditions, with position lights on.

6.50 mMaximum width for signposted bends

Remember

  • You may fit front fog lights: they are optional.
  • You may use them when fog, heavy rain, snow, smoke or dust reduces visibility.
  • You do not always have to switch them on in fog.
  • For bends, meet the width limit and have a signposted series of close bends.
  • In fog, consider whether main beam reflects back and worsens your view.

Exam trap: Wrong: Any bend permits front fog lights. Right: Meet the required width and signposting conditions.

Read the full explanation
  • You may equip your lorry with two white or selective-yellow front fog lights; fitting them is optional. Their purpose is to improve road illumination in adverse conditions. [RGV, art. 17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a17). [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You may use them when fog, heavy rain, snowfall, smoke, dust or similar circumstances significantly reduce visibility. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • In these situations, you must use front fog lights, dipped beam or main beam according to the applicable conditions. You may use front fog lights without dipped beam or together with it, and even with main beam where appropriate; you must keep the position lights on. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106). [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15).
  • You may also use them on narrow sections with many bends when the carriageway is 6.50 m wide or less and signs warn of a series of closely spaced bends. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • In fog, as practical advice, you must consider that main beam can reflect back and worsen your vision. You may choose dipped beam and front fog lights where appropriate. The legal option to combine lights does not mean that the brightest combination always gives you the best view. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).

12Rear fog lights: severe conditions only

A truck travels in the right lane through thick fog with one red rear fog light switched on and its position lights visible.
The key idea

Use rear fog lights only in particularly poor visibility.

Remember

  • Use them in thick fog, very heavy rain or heavy snowfall.
  • Use them in dense clouds of dust or smoke too.
  • Keep dipped beam, main beam or front fog lights on so they can work.
  • Do not replace position lights with rear fog lights.
  • Switch them off when these particularly poor conditions end.

Exam trap: Wrong: Light snowfall allows rear fog lights. Right: You need particularly poor visibility.

Read the full explanation
  • Your lorry must have one or two red rear fog lights. If you have one, the general table specifies a position on the left or in the centre; if you have two, they are positioned towards the outer edges. Their purpose is to make your vehicle more visible to those approaching from behind. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must only switch them on in particularly adverse conditions: thick fog, very heavy rain, heavy snowfall or dense clouds of dust or smoke. Light snowfall that significantly reduces visibility requires appropriate lighting, but does not in itself justify using rear fog lights. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • For your rear fog lights to work, main beam, dipped beam or front fog lights must also be on. The electrical connection and the circumstances that authorise their use are separate requirements that you must meet. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15). [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • You must switch them off when the particularly adverse conditions end to avoid disturbing those following you. A narrow, winding section that permits front fog lights does not in itself authorise rear fog lights. The conditions for use apply to each device separately. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).

13Indicators: signalling a movement

A heavy goods truck travels in the right lane of a divided motorway with its left rear indicator and left side repeater illuminated to signal an intended move to the left.
The key idea

Signal your movements early and check that you can move safely.

Remember

  • Use the indicator on the side towards which you intend to move.
  • Check that your load does not hide the side indicators.
  • Check the lamps if your indicator flashes too quickly.

Exam trap: Wrong: Your indicator gives you priority. Right: It only shows your intention.

Read the full explanation
  • Your lorry must have an even number of amber direction indicators greater than two, fitted at the front, rear and sides as required for its category. You must check that the load body or load does not obscure the side repeaters: these matter to people alongside the vehicle. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must use the indicators to communicate the direction in which your lorry will move. Advance warning, the duration of the signal and arm signals are covered in «Manoeuvres with a lorry». [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).
  • If the indicator warning light flashes faster than usual, you must check whether a bulb has stopped working. A marked change in frequency can warn you of a fault; you must not interpret it as confirmation that all the indicators work or as sufficient evidence to diagnose a short circuit. [UN Regulation 48](https://www.boe.es/buscar/doc.php?id=DOUE-L-2021-81325).

14Braking and reversing

A truck viewed from behind travels in the right-hand lane of a rural road with its two red brake lights illuminated.
The key idea

Use the correct lights to warn others that you are braking or reversing.

LightColour and purpose
BrakeRed: shows that you are braking
ReversingWhite: lights the area behind and warns that you intend to reverse

Remember

  • Distinguish a high brake light from end-outline marker lights.
  • Check that the area is clear before reversing.
  • Follow reversing rules even when your reversing light is on.

Exam trap: Wrong: A reversing light guarantees clear space. Right: You must check the area yourself.

Read the full explanation
  • Your brake lights are red and fitted at the rear: they signal that you are applying the service brake. The general table for lorries specifies two at the outer edges. You must not confuse their function with that of position lights or the rear fog light, even though these are also red. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Your lorry may have a third, high-mounted red brake light. The RGV lists it as optional in the general list for lorries, subject to the vehicle's specific type approval. You must distinguish it from the two high-mounted end-outline marker lamps: it signals braking rather than the vehicle's width. [RGV, art. 17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a17). [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Your lorry must have white reversing lights; the general table specifies one or two according to the regulations for its category. They illuminate the area behind you and signal that you are reversing or about to do so; you must not interpret them coming on as a guarantee that the area is clear. [RGV, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Warnings by repeated braking and signals for reversing are covered in «Manoeuvres with a lorry». [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).

15Hazard warning lights: warning of a temporary danger

A green truck travels in the right lane of a road with both rear turn indicators illuminated simultaneously and no beacon on the roof.
The key idea

Use hazard warning lights for temporary danger, alongside other required lights.

Remember

  • Hazard warning lights flash all your indicators together.
  • Use them if you cannot reach minimum speed and rear-end collision is a danger.
  • Distinguish your V-16 beacon from your hazard warning lights.

Exam trap: Wrong: Driving slowly always requires hazard warning lights. Right: You must be below minimum speed and risk being hit from behind.

Read the full explanation
  • When you switch on the hazard warning lights, you operate all your lorry's direction indicators simultaneously. This amber warning signals that your vehicle presents a temporary danger to other road users. [RGV, annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • If you cannot reach the minimum speed and there is a risk of a rear-end collision, use your hazard warning lights: see «Speed and safe following distances», «When you can drive more slowly». [RGC, art. 49.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49).
  • Their use when you become stationary on a motorway or dual carriageway, or in reduced visibility, is covered in «Manoeuvres with a lorry». [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).
  • The V-16 and the hazard warning lights are different devices: the beacon has its own power supply, while the four flashing indicators belong to your lorry's electrical system. You must follow the conditions of use for each; lighting while your lorry is stationary is explained in «Lights when your lorry is stationary». [RGC, art. 130](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130).

16Lights when your lorry is stationary

A truck immobilized beside the right-hand kerb on a dark road through a village keeps its red position and clearance lights, hazard lights and an amber beacon on the cab roof illuminated.
The key idea

Keep the required lights on when your lorry is stationary.

Location and situation for your lorryLighting rule
Dark through road in a built-up area, at nightKeep position lights on
Same road at night, parallel parkedYou may use parking lights or position lights on the carriageway side, subject to conditions
Other urban road, parkedYou may switch position lights off if others can see you far enough away

Remember

  • When immobilised on road/shoulder, keep position lights on at night or in poor visibility.
  • Add end-outline marker lights when required.
  • Do not replace required lights with hazard warning lights.

Exam trap: Wrong: You can park on any street without position lights. Right: Check location, lighting and situation.

Read the full explanation
  • If you become immobilised on the carriageway or arcén (hard shoulder) at night or in the reduced visibility conditions specified in article 106, you must keep your position lights and, where applicable, end-outline marker lamps on. This obligation applies whatever the cause; a breakdown does not allow you to leave your vehicle unlit. [RGC, art. 105](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a105).
  • If you stop or park at night on the carriageway or hard shoulder of an inadequately lit stretch of road through a town, you must keep your position lights on; if you are parked parallel to the kerb, you may replace them with parking lights or the two position lights on the side facing the carriageway, provided you meet the dimensions that permit parking lights to be fitted, as specified in the next section. [RGC, art. 105.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a105).
  • On an urban road other than a stretch of road through a town, you may park without keeping your position lights on if the lighting allows others to see your vehicle from a sufficient distance. You must not extend this exception to an unlit road or to every breakdown that leaves you immobilised; you must check the location and circumstances. [RGC, art. 105](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a105).

17Parking lights: fitting limited by vehicle dimensions

A compact two-axle truck is parked at night beside the right-hand kerb, with a white front parking light and a red rear parking light illuminated on the road-facing side.
The key idea

Check your vehicle’s dimensions before fitting parking lights.

6 mMaximum length
2 mMaximum width

Remember

  • You may fit them only if your vehicle meets both size limits.
  • You must not fit them to a lorry 7 m long.

Exam trap: Wrong: A narrow 7 m lorry may have parking lights. Right: It exceeds the permitted length.

Read the full explanation
  • You may only fit parking lights to vehicles up to 6 m long and no more than 2 m wide; if your lorry is 7 m long, you cannot fit them. [RGV, art. 17 and annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a17).

18Connected V-16: giving advance warning of an immobilised vehicle

A truck is stopped on the right shoulder with an illuminated V-16 beacon on the cargo box roof, above the entire vehicle body.
The key idea

Carry the required connected, certified V-16 and use it when immobilised in danger.

360 degreesHorizontal coverage
30 minutesMinimum duration at required intensity

Remember

  • Your lorry must carry a connected, certified V-16.
  • Use it when your lorry is immobilised on the road in danger.
  • Recognise its flashing amber light.
  • Do not confuse it with hazard warning lights.
  • Review its placement in “Accidents, breakdowns and first aid”.

Exam trap: Wrong: Triangles or an unconnected beacon suffice. Right: Your Spanish-registered lorry needs a connected V-16 in Spain.

Read the full explanation
  • You must carry in your lorry the connected and certified V-16 warning light required by the regulations in force. In Spain, for your Spanish-registered lorry, triangles and an unconnected beacon do not fulfil the regulatory function of giving advance warning of an immobilised vehicle. [RGV, annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16). [RGV, annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • Your V-16 emits a flashing amber light with 360-degree horizontal coverage. The specification requires it to maintain the prescribed intensity for at least 30 minutes; you must not confuse it with the V-2 on a vehicle working on the road or with hazard warning lights. [RGV, annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • Position and use it as explained in «Accidents, breakdowns and first aid», in the section «Position the beacon without putting yourself at risk».

19Retroreflectors: reflecting without emitting light

A car follows a rigid truck at dusk, and its headlights illuminate the two rectangular red reflectors on the rear of the truck.
The key idea

Recognise reflectors: they reflect other lights and produce no light themselves.

6 mSide reflectors required above this
Position and vehicleReflectors
Lorry rearRed, non-triangular
Trailer rearRed triangles
Lorry frontWhite, non-triangular; optional
Lorry sideUsually amber; a red rear exception exists

Remember

  • Do not replace required lights with reflectors.
  • Check both side reflectors and side marker lights.
  • Do not classify reflective number plates or panels as reflectors.

Exam trap: Wrong: Every lorry needs triangular rear reflectors. Right: Rear triangles identify trailers.

Read the full explanation
  • A retroreflector reflects light from an external source, such as the headlights of an approaching vehicle, and produces no light of its own. Its effectiveness does not replace compulsory use of lights; you may still be driving your lorry unlawfully with visible reflectors if the required lights are off. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx). [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99).
  • Your lorry must have two red, non-triangular rear retroreflectors. White, non-triangular front retroreflectors are optional in the general table. You must associate a red rear triangle with a trailer or semi-trailer, rather than with a rigid lorry simply because it carries goods. [RGV, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, art. 17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a17). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • If your lorry is longer than 6 m, it must have non-triangular side retroreflectors. Their standard colour is amber, with a regulatory exception for a rear side retroreflector grouped with certain red devices. You must check both reflectors and side marker lamps: having one does not replace the other. [RGV, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must not classify retroreflective number plates or the retroreflective panels and signs required for your vehicle category or service, including ADR signs, as retroreflectors. Although they all reflect light back, the regulations distinguish between these categories. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).

20V-6: recognising a long vehicle

A long articulated truck travels in the right lane of a rural road with a yellow plate bordered in red centered on its rear.
The key idea

Display V-6 when your vehicle or combination exceeds the required length.

12 mV-6 required above this length
500 mmMinimum fitting height
1,500 mmMaximum fitting height
V-6 placementWhat you must do
Single plateFit it centrally at the rear
Replacement platesFit them symmetrically, as close as possible to the edges

Remember

  • Measure the full combination length when you tow a trailer.
  • Recognise the yellow reflective plate with a fluorescent red border.
  • Fit it centrally at the rear.
  • Where fitting requires it, you may use matching plates symmetrically near the edges.
  • Do not use it to replace required lights or markings.

Exam trap: Wrong: Exactly 12 m requires V-6. Right: Your vehicle or combination must exceed this length.

Read the full explanation
  • You must display the V-6 sign when your vehicle or combination is longer than 12 m. Exactly 12 m does not exceed this threshold. When towing a trailer, you must consider the total length of the combination, without confusing it with the length of the load body or the lorry alone. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • The V-6 is a reflective yellow plate with a fluorescent red border, fitted at the rear. Its purpose is to warn of the length; it does not indicate mass, is not an ADR panel and does not replace the required end-outline marker lamps, side marker lamps or contour markings. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • You must centre the rear plate on the longitudinal centreline. Where this makes fitting easier, you may replace it with two plates of similar characteristics, positioned symmetrically and as close as possible to the edges. In either case, you must fit them between 500 and 1,500 mm above the ground. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).

21V-23: lorry contour markings

A rigid truck travels in the right lane of a rural road with yellow retroreflective strips forming a complete rear outline and partial side markings.
The key idea

Check whether your lorry needs V-23 reflective strips to show its outline.

2.10 mRear marking width threshold
6 mSide marking length threshold
7.5 tN2 maximum mass must exceed
10 July 2011Registration requirement starts here
Face of vehicles in the stated categories, dates and exceptionsRequired marking above threshold
Rear: over 2.10 m wideFull outline
Side: over 6 m longPartial outline

Remember

  • Check the category: N2 above 7.5 t and N3 are included.
  • O3 and O4 are also included under their rules.
  • Check exceptions for chassis-cabs, incomplete vehicles and tractor units.
  • Do not automatically apply the tractor unit’s exception to its semi-trailer.
  • For vehicles registered before the stated date, fitting is voluntary.
  • Do not cover the markings with tarpaulins or accessories.

Exam trap: Wrong: Any reflective tape counts as V-23. Right: Use approved strips.

Read the full explanation
  • The V-23 consists of type-approved retroreflective strips that make the outline, length and width of a heavy vehicle recognisable from the rear or side. These are not battery-powered lights, and fitting them is not equivalent to sticking any reflective advertising tape onto the bodywork. [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23).
  • If your lorry is in category N2 with a maximum mass exceeding 7.5 t, or in category N3, you must apply two independent criteria: full rear contour markings when its width exceeds 2.10 m, and partial side contour markings when its length exceeds 6 m, subject to the exceptions in the next point. [UN Regulation 48, paras. 6.21.1.2.1 and 6.21.1.2.2.1](https://www.boe.es/buscar/doc.php?id=DOUE-L-2021-81325).
  • You must take account of the exceptions for chassis-cabs, incomplete vehicles and tractor units for semi-trailers. Categories O3 and O4 are also included under their applicable rules; you must not automatically apply the tractor unit exception to the semi-trailer it tows. [UN Regulation 48, para. 6.21.1.2](https://www.boe.es/buscar/doc.php?id=DOUE-L-2021-81325).
  • For the categories and conditions specified, you must display V-23 if your vehicle is registered on or after 10 July 2011; fitting it is voluntary for vehicles registered earlier. [Order PRE/52/2010, sole final provision.b](https://www.boe.es/buscar/doc.php?id=BOE-A-2010-1011).
  • You may find line markings instead of contour markings where the shape, structure, design or operation prevents fitting contour markings, in accordance with the technical requirements. You must maintain the required markings without covering them with tarpaulins or accessories; V-23 complements the lights and other signalling devices. [UN Regulation 48, para. 6.21.1.2.3](https://www.boe.es/buscar/doc.php?id=DOUE-L-2021-81325). [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23).

22Panels and lights for projecting loads

A truck travels in the right lane with secured timber beams and a square V-20 panel with five red and five white diagonal stripes at the rear end of the load.
The key idea

Mark projecting loads with the required panels and lights.

PanelWhat you must recognise
V-20Marking a projecting load
V-11Dangerous goods where required

Remember

  • Review V-20 and its additional lighting in “Load stowage and safety”.
  • Recognise V-11: orange panels for dangerous goods where required.
  • On numbered orange panels, identify the hazard above and the substance below.

Exam trap: Wrong: The top number on an orange panel identifies the substance. Right: Hazard above, substance below.

Read the full explanation
  • You study the marking of projecting loads with V-20 and their additional lighting in “Load stowage and safety”. [RGC, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • V-11 uses orange panels to identify the carriage of dangerous goods where this requirement applies. If the panels bear numbers, those at the top identify the hazard and those at the bottom identify the substance. You study the circumstances, exemptions and labels in “Dangerous goods: ADR basics”. [RGV, Annex XI, V-11](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-11).

23Signals for special services and circumstances

A maintenance tipper truck is stopped at the right edge of the road with an amber beacon lit above its cab, beside two cones and a pile of gravel.
The key idea

Recognise your lorry’s special signals and what they allow you to do.

40 km/hSlow vehicle: maximum design speed
100 mRequired visibility of V-2
SignalMeaning you must recognise
V-2Vehicle presenting an obstruction: amber light
V-1Priority service: blue light
V-4Maximum speed shown
V-5Slow vehicle by design
V-14Learner vehicle
V-24Public-road recovery service
V-19Passed inspection and next inspection date

Remember

  • Use V-2 for road work, special transport or escort duties when required.
  • For routine road work: when stopped, parked or travelling up to 40 km/h.
  • If V-2 fails, use dipped beam and hazard warning lights.
  • Place V-19 inside the upper right-hand corner of your windscreen.

Exam trap: Wrong: Amber V-2 gives you priority. Right: It warns that your vehicle presents an obstruction.

Read the full explanation
  • If your lorry works on the road under the conditions specified in the regulations, you must use V-2, an amber light indicating a vehicle that presents an obstruction. This covers vehicles regularly carrying out these tasks while stopped, parked or travelling at no more than 40 km/h, as well as special transport vehicles and escorts under their applicable conditions. [RGV, Annex XI, V-2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-2).
  • V-2 must be visible in all directions from 100 m and fitted without impairing your visibility. If it fails, you must use dipped beam together with the hazard warning lights. The amber light does not give your vehicle priority; V-1 is the blue signal used by the specified priority services. [RGV, Annex XI, V-2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-2). [RGV, Annex XI, V-1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-1).
  • V-4 indicates a speed restriction; V-5 identifies a slow vehicle. The former shows the maximum speed displayed on the plate and is required in the circumstances specified in the regulations, such as for vehicles with special authorisation; the latter identifies vehicles whose design prevents them from exceeding 40 km/h. [RGV, Annex XI, V-4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-4). [RGV, Annex XI, V-5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-5).
  • Depending on your lorry’s service, V-14 identifies learner driving; V-24 identifies roadside assistance services; V-19 certifies a satisfactory periodic inspection and shows the next inspection date. If your vehicle has a windscreen, you must place V-19 on the inside in its top right-hand corner. You study ITV (vehicle roadworthiness test) intervals in “Professional transport documentation”. [RGV, Annex XI, V-14](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-14). [RGV, Annex XI, V-24](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-24). [RGV, Annex XI, V-19](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-19).

24Number plates and their lighting

A truck travels in the right-hand lane of a road at dusk, with a white light directed onto its rear registration plate and its red rear lights illuminated.
The key idea

Keep your number plates visible and light the rear plate when required.

750 kgTrailer MMA threshold
Trailer MMAPlates required at the rear
Up to 750 kgTowing vehicle’s registration
Over 750 kgTrailer’s own registration and towing vehicle’s registration

Remember

  • Keep your lorry’s front and rear plates clean and readable.
  • Light the rear plate at night, in tunnels and in poor visibility.
  • Check the trailer’s number plate light too.

Exam trap: Wrong: Your lorry’s plate light suffices for the trailer. Right: Check the trailer’s own plate lighting.

Read the full explanation
  • Your lorry must have two number plates, one at the front and one at the rear, fitted as required by the regulations. You must keep them visible and legible: the number plate must not be obscured by the load, accessories or dirt. The plates identify the vehicle and do not replace any of its lighting devices. [RGV, art. 49 and Annex XVIII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • You must illuminate the rear number plate when driving at night, through tunnels or underpasses, and when visibility is significantly reduced. The device directs white light towards the plate; you must not confuse it with a white lamp shining backwards to indicate reversing. [RGC, art. 103](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a103). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • If you tow a trailer with an MMA (maximum authorised mass) not exceeding 750 kg, you must display a plate bearing the towing vehicle’s registration number at the rear. Trailers with an MMA exceeding 750 kg carry their own number plate and another bearing the towing vehicle’s registration number, positioned as required by the regulations; you must distinguish between these two identification functions. [RGV, art. 25 and Annex XVIII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • You must also check the trailer’s rear number plate lighting: it forms part of its compulsory equipment. You must not limit your checks to the plates or assume that the lorry’s number plate lamp alone illuminates the plate at the rear of the towed vehicle. [RGV, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).

25Brief warnings and system condition

A truck travels at night in the right-hand lane of a rural road with a short headlight beam illuminating the nearby asphalt.
The key idea

Keep your lights working properly and adjust your speed if they fail.

Remember

  • Review brief flashes in “Manoeuvres with a lorry”.
  • If lights fail irreparably, slow down to stop within the remaining lit area.
  • Keep headlights clean and adjust them for your load using the manufacturer’s instructions.
  • Do not fit unauthorised lights, paints or reflective materials.
  • For spares, see “Lorry maintenance and checks”: “Breakdown warning and emergency equipment”.
  • Avoid interior-light reflections that make it difficult to see outside.

Exam trap: Wrong: A work light replaces driving lights. Right: It only lights a task.

Read the full explanation
  • Brief flashes of dipped beam or main beam are light warnings whose use and purposes are explained in «Manoeuvres with a lorry». [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).
  • If the lighting you need becomes unusable or develops a fault that cannot be repaired during the journey, and you have to drive with less intense lights, you must reduce your speed until you can stop the lorry within the area they illuminate. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107).
  • You must keep your headlights clean and correctly aligned. As a practical check, a beam aimed too low limits your range of vision, while one aimed too high can dazzle others; you must adjust the system to suit the load and follow the manufacturer’s procedure. Horizontal and vertical adjustment changes the direction of the beam, not the physical size of the headlight. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15).
  • You must not apply unauthorised paint or fit unauthorised lights or reflectors. Paired devices serving the same purpose must match in colour and intensity and be positioned symmetrically; you must maintain the type approval of the assembly even when you add accessories. A work light illuminates a task and does not replace the lighting required for driving. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Consult «Lorry maintenance and checks», section «Breakdown warning and emergency equipment», for the spare parts and tools you must carry in your lorry. [RGV, Annex XII.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • You may have interior cab lighting, but you must use it without dazzling or unduly disturbing other road users. As a practical precaution, avoid reflections in the windows that make it difficult to see outside at night; the interior light does not replace any of the lights used for driving. [RGV, art. 17 and Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).

Choosing your lights when driving

Consider the road conditions before selecting your headlights.

  1. Identify night-time, tunnels or significantly reduced visibility; also check whether the lane requires dipped beam during the day.
  2. Switch on the position lights, rear number plate light and end-outline marker lamps where required.
  3. Select dipped beam in built-up areas or where lighting is sufficient; outside built-up areas with insufficient lighting, apply the main beam rule at more than 40 km/h.
  4. Check whether you could dazzle anyone directly or through their mirrors, and switch to dipped beam as soon as this becomes possible.
  5. Assess front and rear fog lamps separately: the rear fog lamp requires particularly adverse conditions.

Warning others of a lorry breakdown

Combine advance warning with the required lighting.

  1. Bring your lorry to a standstill in the safest possible place and switch on the hazard warning lights.
  2. Keep the position lights and end-outline marker lamps on when required because of darkness or reduced visibility.
  3. Activate the connected V-16 and place it on the highest accessible exterior part, with maximum visibility and without exposing yourself to traffic.
  4. If you cannot reach the cab roof, use a suitable attachment on the door; do not climb onto the load body.
  5. Request the help you need: the beacon’s connection does not replace notifying the emergency services.

Checking lights and markings according to dimensions

Each device has its own criterion.

  1. Check your lorry’s length: if it exceeds 6 m, check the side-marker lamps and side reflectors, allowing for their exceptions.
  2. Check its width: if it exceeds 2.10 m, check the end-outline marker lamps.
  3. Check the total length of the vehicle or combination: if it exceeds 12 m, check V-6.
  4. For V-23, check the category, maximum mass, registration date and the separate criteria for rear width and side length.
  5. If the load projects beyond the vehicle, check V-20 and any additional lights and reflectors required.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module