Theory · C Licence - Truck · Module 6 of 18

Signs and their hierarchy for lorries

You learn to apply the hierarchy of signs and interpret traffic officers’ signals, roadworks signs, traffic lights, upright signs and road markings. You distinguish the restrictions on goods vehicles, MMA (maximum authorised mass), actual mass and dimensions that determine where you can drive your lorry.

36 min read27 sectionsReviewed Nov 3, 2026
A rigid truck waits at a red traffic light beside a roadworks warning sign on a two-way road.
Understanding and obeying road signals in a truck

Sign library

All 620 signals of the official catalogue in force (Royal Decree 465/2025), each with its drawing and description, and a test to practise them.

1Hierarchy and compatible signs

A truck with its driver on the left side of the cab remains stopped before a traffic officer with a raised arm, although the traffic light is green.
The key idea

Obey the sign with the highest priority first.

Remember

  • Obey traffic officers first.
  • Next, obey temporary signs, barriers and devices that change normal traffic arrangements.
  • Then follow traffic lights, upright signs and road markings, in that order.
  • If signs of the same type conflict, obey the more restrictive one.
  • With circular green lights, still obey compatible turning and access restrictions.
  • If the traffic light is unlit, obey the other signs.

Exam trap: Wrong: Always choose the most restrictive sign. Right: Check its priority first.

Read the full explanation
  • You must obey, in this order: traffic officers’ signals and orders; temporary signs and markers that change the normal traffic arrangements, boundary devices and guidance markers; traffic lights; upright signs; road markings. A permanent triangular warning sign does not acquire the priority of temporary markers. [RGC, art. 133](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a133).
  • When two messages contradict each other, you must follow the one with higher priority. If they are of the same type, you must follow the more restrictive one. For example, if an upright STOP sign and an upright give way sign contradict each other, the requirement to stop takes priority; if an upright give way sign and a painted STOP marking contradict each other, the upright sign takes priority. [RGC, art. 133](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a133).
  • A circular green traffic light allows you to proceed, but a no left turn sign still restricts that manoeuvre: you can comply with both. An officer’s order to stop takes priority over the green light. [RGC, art. 133](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a133).
  • If the circular traffic light controlling the junction allows you to proceed and there is a STOP sign for the same approach, you follow the traffic light. If it is unlit, you must follow the other signs present. How lane-control signals apply is explained in «Arrows and lane-control signals». [RGC, art. 133](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a133).

2Who each sign applies to

An orange truck remains stopped before the stop line at a red traffic light on its right on a two-way road.
The key idea

Check which signs apply to your lane and route.

Remember

  • Check signs immediately right, above the road or above your lane.
  • Without these, check left for straight ahead or left turns.
  • If left and right differ, follow left for straight ahead or left turns.
  • Read arrows, times and vehicle categories too.
  • Obey restrictions even when your lorry is empty.

Exam trap: Wrong: Read only the main sign. Right: Read its plates and arrows too.

Read the full explanation
  • You must obey signs that impose requirements or prohibitions and adapt your behaviour to the other messages. If you must stop, you cannot move off again until you comply with the requirement. Driving an empty lorry or being familiar with that road does not exempt you from an applicable restriction. [RGC, art. 132](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a132).
  • You must follow the traffic lights and upright signs immediately to your right, above the carriageway or above your lane. If there are none in those positions and you are going straight ahead or turning left, you follow those immediately to your left. If the indications on the right and left differ, you obey those on the left when going straight ahead or turning left. [RGC, art. 132](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a132).
  • You must always read everything together: the main sign, arrows, supplementary plate, times, vehicle category and lane. A prohibition above one lane may have a different scope from a sign applying to the whole carriageway. [RGC, art. 132](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a132).

3Sign categories and scope

A rigid truck travels in the right-hand lane of a road and approaches a no-overtaking sign for trucks on the right-hand shoulder.
The key idea

Recognise each sign’s message and where it starts to apply.

CategoryWhat it tells you
WarningWarns you of a hazard
RegulatorySets requirements, prohibitions or priority
InformationInforms or guides you

Remember

  • Obey regulatory signs from their position, unless a plate delays their start.
  • Do not wait until the next junction.
  • Regulatory signs beside, above or below town names apply throughout.
  • Check whether particular sections have different rules.
  • Interpret illuminated white symbols on dark backgrounds too.

Exam trap: Wrong: Decide by shape and colour alone. Right: Recognise the specific message.

Read the full explanation
  • Warning signs alert you to a hazard; regulatory signs set priority, entry rules, restrictions, prohibitions or requirements; information signs provide information, directions or identify special rules. The specific message determines the meaning; there are exceptions to the usual shapes and colours. [RGC, art. 145](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a145).
  • Regulatory signs apply from the point across the road where they stand, unless a supplementary plate indicates the distance to where the rule begins. Where the rule ends depends on each sign and the circumstances described in the catalogue. [RGC, art. 145](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a145).
  • If a regulatory sign is beside, directly above or directly below the sign bearing the name of a built-up area, you must apply the rule throughout that built-up area, unless different rules apply on particular stretches. A sign merely located near a town does not automatically have that scope: you must check its association with the name sign. [RGC, art. 145](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a145).
  • You may encounter illuminated white symbols on a dark background under the conditions laid down in the regulations. You must interpret their meaning and must not treat them as mere advertisements because of their appearance. The official catalogue sets out how each category applies; for your lorry, goods categories, masses and clearance dimensions are especially relevant. [RGC, art. 145](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a145).

4Traffic officers’ gestures and whistle signals

A truck is stopped before a stop line in front of a traffic officer holding one arm vertically upwards.
The key idea

Obey the officer’s gestures and whistle signals.

Whistle signalWhat you must do
Short, frequent blastsStop
Long blastMove off again

Remember

  • With an arm raised vertically, stop unless you cannot stop safely.
  • If already inside the junction, that gesture does not require stopping inside.
  • With arms horizontal, stop if your approach crosses the line of their arms.
  • Stop if the officer waves a red or yellow light towards you.
  • If the officer moves an outstretched arm up and down, slow down when:
  • You approach from that arm’s side, at right angles to it.

Exam trap: Wrong: Move off when the officer lowers their arms. Right: Wait until the order changes.

Read the full explanation
  • If an officer raises one arm vertically, you must stop as you approach, unless you cannot do so safely enough. If the officer makes this gesture at a junction and you have already entered it, the order does not require you to stop inside. You must stop before the nearest stop line or, if there is none, before reaching the officer; at a junction, before entering it. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • When an officer holds one or both arms out horizontally, you must stop if your line of approach crosses the line indicated by the arms, whichever direction you are travelling in. The order remains in force even if the officer lowers their arms, until they change position or give another signal. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • If an officer waves a red or yellow light towards you, you must stop. If the officer moves an outstretched arm up and down, you must slow down when you approach from the side of that arm and at right angles to it. You must distinguish an order to slow down from an order to stop completely. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Several short, frequent whistle blasts order you to stop your vehicle; one long blast orders you to move off again. Officers may also use other clear signals when circumstances require them. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

5Orders from vehicles and authorised personnel

A truck is stopped beside the right-hand kerb, ahead of a police patrol car emitting a red light signal towards it.
The key idea

Follow police orders and signs used by authorised personnel.

150 mMinimum visibility of personnel
Flag displayed from a vehicleWhat you must do
RedCarriageway closed from where the vehicle passes; do not go on unless officers accompany or escort you.
GreenYou may pass once the vehicle carrying it passes
YellowTake extra care

Remember

  • If an officer signals at you with a still, downward arm, stop right.
  • If police behind you aim a flashing red light forwards, you must stop.
  • Stop on the right, in front of the police vehicle.
  • Follow instructions; avoid creating greater danger or inconvenience when stopping.
  • Obey sign paddles used by personnel acting with authorisation.
  • Personnel visibility distance does not tell you where to stop.

Exam trap: Wrong: Every yellow flash orders you to stop. Right: Recognise the specific police order.

Read the full explanation
  • A red flag displayed from a vehicle announces the temporary closure of the carriageway from the moment that vehicle goes by, except for road users accompanied or escorted by officers. A green flag announces its reopening from the moment the vehicle carrying it goes by. A yellow flag requires you to take extra care because of a hazard and also applies to other road users. [RGC, art. 141](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a141).
  • If an officer in a vehicle holds an arm downwards, at an angle and stationary, you must stop on the right if the signal is directed at you. A blinking or flashing red light directed forwards from a police vehicle orders you, as the driver ahead, to stop on the right, in front of the patrol vehicle, where you do not create greater risks or inconvenience, following the officers’ instructions. [RGC, art. 141](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a141).
  • A vehicle’s yellow warning light indicates its presence or the service it is carrying out; a police order to stop depends on the prescribed signal directed at you. When stopping your lorry, you must stop where the officer indicates and avoid an abrupt reaction that creates additional danger. [RGC, art. 141](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a141).
  • You must follow the prescribed signs on paddles used by roadworks personnel and personnel escorting special transport operations when they act in authorised circumstances. School patrols may use paddles to invite you to stop. Personnel empowered to act at authorised activities may prevent you from entering the affected area; their duties depend on their authorisation. [RGC, art. 141](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a141).
  • People directing traffic must wear conspicuous clothing and retroreflective elements so that you can distinguish them from at least 150 m, both by day and at night. This figure describes their visibility; it is neither the distance at which you must stop your lorry nor a gap you must leave from the patrol vehicle. [RGC, art. 141](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a141).

6Roadworks and temporary signs

A truck travels in its lane beside a yellow boundary and cones, with a triangular roadworks warning sign with a yellow background on the right shoulder.
The key idea

At roadworks, follow temporary signs and check whether your lorry can pass.

Signs, markings or laneWhat you must know
New roadworks markingsYellow
New roadworks direction signsYellow background and black lettering
Other temporary causesOrange on the relevant upright signs

Remember

  • Read the whole message on variable signs.
  • Distinguish information, advice and compulsory orders.
  • Follow diversions while they remain in force.
  • Check permitted height, mass and speed.
  • Recognise P-18 as a roadworks warning.
  • Follow normal signs again when the temporary change ends.

Exam trap: Wrong: Every message panel gives advice. Right: Some messages impose requirements.

Read the full explanation
  • You must read variable message signs: they may inform, warn, recommend or impose instructions. A temporary height, mass or speed restriction applies to your lorry according to the message displayed. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Temporary changes end when their signs indicate or when the circumstances that caused them cease. You must then follow the normal signs. While a diversion or marked route remains in force, follow its route even if you remember a different lane layout from previous journeys. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • At roadworks, warning and regulatory signs whose normal background is white use a yellow background in the cases specified in the catalogue. P-18 warns you of roadworks. New roadworks direction signs have a yellow background and black lettering; normal signs that remain applicable may retain their design. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • New markings on stretches with roadworks are yellow; existing white markings may remain if they still apply. For temporary signs used for other reasons, the catalogue specifies orange instead of yellow for the corresponding upright signs. You must interpret the message and how it applies, without deciding solely on the basis of colour. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • On reversible lanes and lanes opened to traffic travelling against the normal direction, you must follow the signs governing their use; see «Lanes with specific limits» in «Speed and safe following distances» for the conditions of use. [RGC, art. 40](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a40) and [art. 41](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41).

7Boundary and guidance devices

A rigid truck stays in its lane before a transverse row of cones marking off roadworks on a two-way road.
The key idea

Respect devices that close or mark off parts of the road.

Delineation lightsWhat you must do
Steady redDo not pass: the carriageway is closed
Steady or flashing amberDo not cross the line joining them

Remember

  • Do not cross the line joining cones or temporary edge markers.
  • Do not cross temporary directional panels.
  • Respect movable barriers that close the road.
  • Use reflective devices to guide you in poor light.
  • Check height clearance at a gantry.
  • Watch windsocks: your lorry has a large side area.

Exam trap: Wrong: Drive through a gap between cones. Right: Do not cross their line.

Read the full explanation
  • Boundary devices prohibit entry into the part of the road they mark off. A temporary direction panel prohibits crossing it and indicates the direction of travel; temporary cones and edge bollards prohibit crossing the real or imaginary line joining them. A gap between cones does not authorise you to overtake or change lanes. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • A steady red warning light indicates that the carriageway is completely closed. Steady or flashing amber lights prohibit crossing the imaginary line joining them. A flashing amber traffic light has the meaning explained in «Circular traffic lights». [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • A movable barrier placed across the road temporarily prohibits entry. You must obey it at level crossings, checkpoints or toll booths while it remains in that position. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Edge marker posts and horizontal or vertical road reflectors help guide you, especially in low light. A traffic divider marker identifies where two traffic streams separate; permanent direction panels help you see bends. These devices do not, by themselves, set a numerical speed for negotiating the road. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • A windsock supplements P-29 and provides information about the wind; a height-clearance gantry warns or prevents vehicles that are too high from continuing towards a nearby structure. You must pay particular attention to these devices because of your lorry’s height and side area. Restraint systems aim to reduce the consequences of leaving the road and do not guarantee that this is prevented. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

8Circular traffic lights

A truck is stopped before the stop line at a red traffic light, leaving the intersection clear.
The key idea

Understand each traffic light and keep the junction clear.

LightWhat you must do
Steady or flashing redStop
Steady amberStop, unless too close to stop safely when it appears
Flashing amberTake extra care and give way where required
Circular greenYou may proceed with priority; keep the junction clear
Flashing amber for vehicles at crossings with dedicated pedestrian signalsAs a general rule, it cannot coincide with steady pedestrian green. Steady vehicle red must come first.

Remember

  • With steady red, stop before the relevant line or light.
  • Do not accelerate when steady amber appears.
  • With flashing amber, take care and obey signs requiring a stop.
  • With green, do not enter if you would block crossing traffic.
  • Watch the light for your own movement.

Exam trap: Wrong: Pass slowly at flashing red. Right: You must stop.

Read the full explanation
  • A steady red light prohibits you from proceeding. You must stop before the traffic light or the nearest stop line before it; if the light is within or on the far side of a junction, you must not enter the junction or cross the stop line before it. You must anticipate stopping your lorry well in advance and keep the junction clear. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • A flashing red light or two alternately flashing red lights temporarily prohibit you from proceeding, for example at a level crossing, lifting bridge, fire station exit or when a low-flying aircraft approaches. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • A steady amber light requires you to stop, as a red light does, unless you are so close when it comes on that you cannot stop safely enough. It is not an invitation to accelerate. You must assess your lorry’s position and whether you can actually stop it, without confusing this exception with the meaning of flashing amber. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Flashing amber, whether a single light or alternating lights, requires you to take extra care and give way where required; you must also obey any other sign requiring you to stop. As a general rule, at crossings with traffic lights reserved for pedestrians, flashing amber for vehicles must not coincide with a steady green pedestrian light and must be preceded by a steady red light for vehicles. A circular green light allows you to proceed with priority, but you must not enter if you are likely to stop and obstruct crossing traffic. [RGC, Annex I, 4.2 d) and e)](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514); [RD 518/2026, sole article, twenty-six](https://www.boe.es/buscar/doc.php?id=BOE-A-2026-13889).
  • The traffic light cycle comprises the full sequence of signals, not just the green phase. You must obey the signal for your movement without anticipating it on the basis of a light for another approach. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

9Arrows and lane-control signals

A truck remains stopped before the stop line at a red circular traffic light, with a green downward arrow above its lane.
The key idea

Distinguish arrows allowing movements from signals controlling lanes.

Signal above your laneWhat you must do
Red crossDo not use the lane; leave it as soon as possible
Downward green arrowYou may use it, while obeying other requirements
Diagonal downward arrowMove safely into the indicated lane before yours closes

Remember

  • With a green arrow on black, follow its direction cautiously.
  • Give way to traffic in the lane you are joining.
  • Proceed if your lane must follow that arrow.
  • Black arrows keep the meaning of the surrounding red or amber light.
  • When changing lanes, respect traffic already there.

Exam trap: Wrong: A downward green arrow cancels STOP. Right: You must still obey STOP.

Read the full explanation
  • A black arrow on a steady red or amber light limits that signal to the indicated movement. You must interpret the colour and direction together: the shape of a black arrow does not authorise you to turn. Other movements may be controlled by different lights, so you must check which traffic light applies to your route. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • A green arrow on a circular black background allows you to follow the indicated direction even if another light is on. You must proceed with care, give way to road users travelling in the lane you are joining and avoid endangering anyone crossing. If you are in a lane that must follow that movement, you must proceed in the direction of the arrow. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • A red cross above a lane prohibits you from using it: if you are driving in it, you must leave it as soon as possible. A vertical green arrow pointing downwards allows you to use it, but does not override a circular red light, a STOP sign, a give way sign or the general priority rules. Nor does it authorise entry by a lorry that is expressly excluded. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • A diagonal white or amber arrow pointing downwards, whether steady or flashing, indicates that the lane is about to close and you must move safely into the indicated lane. You must prepare to move over while respecting road users already in the destination lane. The arrow does not give you priority to move your lorry sideways. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

10Traffic lights for other road users

An orange truck remains stopped before the stop line at a red traffic light, beside another signal displaying an illuminated green bicycle.
The key idea

Follow the traffic light intended for your vehicle.

White bar for trams, scheduled buses or authorised reserved-lane vehiclesMeaning for those users
HorizontalDo not pass
VerticalYou may go straight ahead
DiagonalYou may turn as shown
FlashingSame meaning as steady amber

Remember

  • Do not follow a cycle-only green light in your lorry.
  • Watch pedestrians when making a permitted movement.
  • Do not follow reserved white bars unless your vehicle is authorised.
  • Carrying passengers does not turn your lorry into a bus.

Exam trap: Wrong: Follow any nearby green light. Right: Check which users it controls.

Read the full explanation
  • An illuminated cycle symbol applies exclusively to cycles. In your lorry, you must obey the vehicle traffic light controlling your approach or the signal for your lane, even if there is another light reserved for cycles or pedestrians beside it. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • On a pedestrian traffic light, a stationary red figure prohibits pedestrians from starting to cross; a walking green figure allows them to do so. A flashing green figure warns that the remaining time to finish crossing is running out. As a driver, you must check pedestrian crossings when making the movement permitted by your own signals. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • White bars on a black background are for trams and regular bus services under the conditions set out in the catalogue, or for vehicles using the relevant reserved lane. A horizontal bar prohibits you from proceeding; a vertical bar allows you to go straight ahead; a diagonal bar allows the indicated turn; a flashing bar has the same meaning as a steady amber light. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • In an ordinary lorry, you must not assume that you are entitled to use a reserved lane or follow its bar signals because you are carrying workers or passengers. You must check the authorised vehicle category and the signal that actually controls your lane. The number of people in the cab does not turn a goods vehicle into a bus. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

11STOP, give way and priority road

A truck waits at a give-way sign and a dashed line while a car travels along the priority road at a T-junction.
The key idea

At STOP, stop completely and give way.

SignWhat you must do
R-1Give way; stop if necessary
R-2Always stop and give way
R-3You have priority at the indicated junctions
R-4That priority ends

Remember

  • Give way to priority-road traffic coming from either side.
  • At STOP, stop even if you see no vehicles.
  • Stop at the line or, without one, immediately before the carriageway.
  • If visibility is poor, move cautiously and stop again where you can see safely.
  • Do not confuse a junction warning with an order to stop.

Exam trap: Wrong: Almost stop at STOP. Right: Stop completely.

Read the full explanation
  • R-1, Give way, requires you to give way to road users travelling on the carriageway or lane you are joining, stopping if necessary. R-2, STOP, requires a complete stop even if you cannot see any other vehicles. At both signs, you must give way to vehicles on the priority road, whether they approach from the right or the left. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • At R-2, you must stop at the stop line; if there is none, immediately before the carriageway you are approaching. If you cannot see well enough from that first position, you must move forward cautiously and stop again where you have visibility, without endangering anyone. Slowing almost to a stop does not comply with STOP. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-3 indicates priority at junctions over roads that cross or join yours; R-4 indicates the end of that priority. You must check the rules at the following junctions: R-4 does not, by itself, require you to stop or mean that you must always give way to every vehicle. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-1 and its variants warn of junctions or merging traffic where you have priority; P-2 warns of a junction where priority to the right applies. These triangular signs give advance warning of the priority rules at the junction; R-1 and R-2 impose the obligation to give way at their location. Read the specific sign at each junction to know who goes first. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

12Priority at narrow sections

A green truck waits at an R-5 sign before a narrow bridge while an orange car crosses it in the opposite direction.
The key idea

Before entering a narrow section, check who has priority.

Sign or casePriority or decision
R-5Oncoming traffic has priority
R-6You have priority over oncoming traffic
P-17Only warns of narrowing

Remember

  • At R-5, wait if entering would force oncoming traffic to stop.
  • At R-6, check that you can pass safely.
  • Do not drive towards a vehicle already occupying the narrow section.
  • A narrowing warning does not give you priority.
  • Without signs, see “Priority at narrow sections, bridges and gradients”.
  • You will find it in “Manoeuvres with a lorry”.

Exam trap: Wrong: Reaching R-5 first gives you priority. Right: Respect priority for oncoming traffic.

Read the full explanation
  • R-5, Priority for oncoming traffic, prohibits you from entering a narrow section if you cannot get through without forcing oncoming road users to stop. You must wait before entering the restricted space. Reaching the sign before the other vehicle does not give you priority. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-6, Priority over oncoming traffic, gives you priority over road users approaching from the other end. You must check that you can get through safely and avoid a collision if another vehicle occupies the narrow section. Having priority does not increase the available width or justify approaching in your lorry without a safety margin. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-17 warns that the road narrows; P-17a and P-17b specify narrowing on the right or left. These signs warn of a reduction in width and do not, by themselves, assign the priority indicated by R-5 or R-6. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Without signs, priority at narrow sections, bridges and gradients is governed by arts. 60-63 of the RGC: see «Priority at narrow sections, bridges and gradients» in «Manoeuvres with a lorry». [RGC, arts. 60-63](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a60).

13No entry for goods vehicles and trailers

A rigid truck with a green box and orange cab is stopped beside the right-hand kerb before an R-106 sign prohibiting entry to goods vehicles.
The key idea

Check whether the restriction concerns goods vehicles, maximum authorised mass or trailers.

SignVehicles affected
R-106Goods vehicles, regardless of mass
R-107Goods vehicles whose MMA exceeds the figure
R-112Motor vehicles towing trailers, except single-axle trailers

Remember

  • Obey R-106 even when empty.
  • At R-107, compare your maximum authorised mass, called MMA.
  • Do not use actual mass to decide at R-107.
  • If R-112 shows tonnage, compare the trailer’s MMA with it.
  • Do not compare trailer tonnage with the combination’s mass.

Exam trap: Wrong: Enter empty at R-107. Right: Compare your MMA with the figure.

Read the full explanation
  • R-106 prohibits entry for vehicles intended to carry goods: lorries, tractor units and vans of all sizes. You must obey it regardless of mass and even when empty. The lorry pictogram does not restrict this prohibition to heavy vehicles or make it a dangerous goods sign. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-107 prohibits entry for goods vehicles whose MMA (maximum authorised mass) exceeds the figure shown. You must compare the maximum authorised mass, not the lorry's actual mass that day. With 5.5 t shown, an MMA above 5,500 kg prevents entry even when empty; with 3.5 t shown, a van with an MMA of 4 t is also affected. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-112 prohibits entry for motor vehicles towing a trailer, except single-axle trailers. If a tonnage is shown, it refers to the trailer's MMA. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • With an R-112 showing 3.5 t, a two-axle trailer with an MMA of exactly 3,500 kg does not exceed the figure; one of 5,000 kg does. A rigid lorry without a trailer is not affected by this sign. The licence you need to drive the combination is explained in «Lorry licences and types of transport». [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

14Other entry prohibitions

A rigid truck with a green box body and orange cab is stopped beside the right-hand kerb before a no-entry sign on a two-way road.
The key idea

Read which vehicles or loads must not enter.

1,000 litresRestriction applies above this
SignWhat it prohibits
R-100Vehicles travelling in either direction
R-101Entry at this access
R-102Entry by motor vehicles
R-108Entry with dangerous goods requiring markings
R-109Entry with explosive or readily flammable goods requiring markings
R-110Entry carrying more than 1,000 litres of water-polluting products

Remember

  • At R-101, you may meet oncoming vehicles.
  • Check your load and whether dangerous goods markings are required.
  • Do not decide just because you drive a tanker.
  • At R-120, read the plate’s environmental conditions.
  • Obey other access restrictions too.

Exam trap: Wrong: Measure R-110 in tonnes. Right: Compare litres.

Read the full explanation
  • R-100 prohibits vehicle traffic in both directions; R-101 prohibits entry at the access point where it is placed. At R-101, traffic may approach you from the opposite direction where travel is permitted. R-102 prohibits entry for motor vehicles and applies to your lorry. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-108 prohibits entry for vehicles carrying dangerous goods that require the signs or markings specified by their particular regulations. R-109 refers to explosive or readily flammable goods under those conditions. Being a tanker is not enough: R-108 and R-109 apply to you when the goods you carry require the signs or markings specified by their particular regulations. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-110 prohibits entry if you carry more than 1,000 litres of products capable of polluting water. The threshold is expressed in litres and must be exceeded: it is neither an MMA nor a mass in tonnes. Route requirements and training are explained in «Dangerous goods: ADR basics». [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-120 restricts entry according to the environmental badge or other environmental criteria that you must read on the supplementary plate or notice. You cannot infer permission solely from the sign's colour or image. Permission for deliveries and the permitted times depend on the message applying to that access point. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Other signs exclude specific categories: R-111, agricultural motor vehicles; R-114, cycles; R-116, pedestrians; R-118, VMP (personal mobility vehicles); R-119, cycles and VMP. A sign excluding another category does not allow you to ignore separate prohibitions that apply to your lorry. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

15Actual mass, axles and dimensions

A person measures the height of the load on a rigid truck stopped beside the right-hand kerb before a stone bridge with a low arch.
The key idea

Compare actual mass and dimensions with the restriction shown.

SignWhat you must compare
R-201Actual total vehicle mass
R-202Mass transmitted by each axle
R-203Total length, including the load
R-204Width, including the load
R-205Height, including the load

Remember

  • At R-200, stop at the indicated checkpoint.
  • Include your load when measuring length, width and height.
  • Check the highest point of the whole combination.
  • Do not divide axle mass between its tyres.
  • Matching the figure is not exceeding it; still check actual clearance and other restrictions.

Exam trap: Wrong: Compare R-201 with MMA. Right: Compare your actual total mass.

Read the full explanation
  • R-200 prohibits proceeding without stopping at the indicated checkpoint, such as customs, police or a toll. You must comply with its requirement before moving off again; it does not simply mean giving way at a junction. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-201 limits laden mass, meaning the vehicle's actual total mass at that moment. It does not refer only to the goods or use MMA as its criterion. With 5.5 t shown, you may proceed if your laden mass does not exceed 5,500 kg and you meet all other restrictions; having an MMA of 18 t does not in itself exclude you. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-202 limits the mass transmitted by each axle through all its wheels. You must check the axle concerned, including twin wheels, without arbitrarily dividing its load between tyres to compare it with the figure. Meeting the total mass limit does not guarantee that you meet the axle restriction. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-203 restricts the overall length of the vehicle or combination, including the load. With 10 m shown, you cannot proceed if you exceed 10 m. You must take any longitudinal overhang into account and must not use only the length of the bodywork or load body to decide whether your lorry fits. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-204 restricts width, including the load. With 2.50 m shown, a lorry 2.55 m wide cannot proceed even if its width is generally permitted. R-205 restricts height, including the load: you must check the highest point of the actual combination, not just the height stated for the cab. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • An R-205 showing 4 m prohibits heights above 4 m; one showing 3.5 m prohibits heights above 3.5 m. Matching a figure does not mean exceeding it, but you must check the actual conditions for getting through and the other signs. General authorisation for dimensions does not remove a local restriction or guarantee access along the entire route. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

16Speed, following distance and overtaking

A truck follows a motorcycle in its lane beside a sign prohibiting trucks from overtaking.
The key idea

Obey speed, following distance and overtaking restrictions that apply to your lorry.

70 mExample minimum following distance
3,500 kgR-306 applies above this MMA
SignVehicles affectedOvertaking prohibition
R-305Vehicles in generalDo not overtake motor vehicles if entering the oncoming traffic area
R-306Lorries with MMA above 3,500 kgDo not overtake motor vehicles in a lorry with MMA above 3,500 kg

Remember

  • Use the lower maximum: the sign’s limit or your lorry’s limit.
  • Obey the maximum from the sign’s position.
  • At R-300, keep at least the distance shown, except when going to overtake.
  • A broken line does not cancel an overtaking prohibition.
  • If R-306 applies to your lorry, do not overtake motorcycles either.

Exam trap: Wrong: R-306 allows overtaking without entering opposing traffic. Right: In a lorry with MMA above 3,500 kg, this is also prohibited.

Read the full explanation
  • R-301 sets a maximum speed in km/h. You must obey it from its location until the next different maximum speed or the applicable end sign. If it shares a post or panel with a warning sign, the limit ends when that hazard ends; on a road without priority, it ends when you leave the junction with a priority road. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • A signed maximum speed does not allow you to exceed your lorry's own limit. You must apply the lowest effective restriction for your vehicle and that stretch of road. General maximum speeds and distances are explained in «Speed and safe following distances». [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-300 requires a gap from the vehicle ahead equal to or greater than the figure shown, except when you intend to overtake. Without a figure, it reminds you to keep the statutory gap. With 70 m shown, it does not indicate a maximum distance or apply only when you follow cars; congestion alone does not remove the sign's requirement. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-305 prohibits overtaking motor vehicles when the manoeuvre involves entering the area reserved for oncoming traffic. You must also obey the general overtaking prohibitions and road markings. A broken line does not allow you to ignore the sign or replace the visibility you need. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-306 prohibits lorries with an MMA above 3,500 kg from overtaking motor vehicles, even without entering the area for oncoming traffic. It applies to your lorry and also to overtaking a motorcycle. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

17Turns, stopping and parking

An orange rigid truck travels to the right in its lane beside a no stopping or parking sign on the right-hand pavement.
The key idea

Distinguish bans on turning, stopping and parking.

SignWhat it prohibits
R-302Turning right
R-303Turning left and making U-turns
R-304Making U-turns
R-307Stopping and parking
R-308Parking

Remember

  • Check the side affected and any arrows.
  • Unless stated otherwise, parking bans end at the next junction in your direction.
  • Read exact times for parking bans covering parts of the month.
  • Do not block an authorised vehicle entrance by parking.
  • Delivering goods gives you no general exemption.
  • At R-310, use your horn only to avoid a collision.

Exam trap: Wrong: R-304 prohibits left turns. Right: By itself, it only prohibits U-turns.

Read the full explanation
  • R-302 prohibits right turns; R-303 prohibits left turns and U-turns. R-304 prohibits U-turns, but does not in itself prohibit a left turn. Turning onto another road and returning in the opposite direction along the same road are different movements. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-307 prohibits stopping and parking on the side where it is placed; R-308 prohibits parking. Unless otherwise indicated, the restriction starts at the sign and ends at the next junction in your direction of travel. A parking prohibition does not in itself prohibit every stop, but you must check the other rules at that location. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-308c prohibits parking from 9:00 on day 1 until 9:00 on day 16; R-308d, from 9:00 on day 16 until 9:00 on day 1 of the following month. You must observe the exact times and the side affected. These signs do not in themselves prohibit stopping. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • On variants with arrows, you must check whether the prohibition extends to one or both sides of the sign and where it ends. Supplementary plates S-820 and S-821 indicate extension to the right and left; S-830, to both sides. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-308e identifies a vado (vehicle access) whose entrance or exit you must not obstruct by parking; R-309 limits parking duration according to the system indicated. R-310 prohibits audible warnings except to prevent an accident. Needing to deliver goods does not give you a general exemption from these prohibitions. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

18Compulsory directions and carriageways

A truck with an orange cab and green box body travels in the right-hand lane of a carriageway marked with a blue mandatory truck carriageway sign beside a fork.
The key idea

Follow the compulsory route for your vehicle and load.

1,000 litresR-415 applies above this volume
SignVehicles or loads required to use this carriageway
R-406Goods vehicles; with tonnage, only those whose vehicle or combination MMA exceeds it
R-414Vehicles carrying dangerous goods requiring markings
R-416Vehicles carrying explosive or readily flammable goods requiring markings
R-415Vehicles carrying more than 1,000 litres of water-polluting products

Remember

  • Obey arrows showing compulsory directions and passing sides.
  • At R-402, keep the central island on your left.
  • A compulsory direction does not give you priority.
  • With tonnage on R-406, use it if your vehicle or combination’s MMA exceeds it.
  • Do not enter reserved routes that exclude your lorry.

Exam trap: Wrong: R-415 prohibits entry. Right: It shows the carriageway you must use.

Read the full explanation
  • You must follow the arrows for compulsory directions, compulsory sides to pass and the only permitted directions. R-402 requires you to follow the circular direction shown, keeping the central island on your left. You must determine entry priority from the relevant signs; R-402 determines the direction in which you go around the island. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-406 requires you to use the carriageway where it is placed if you drive a lorry, tractor unit or van of any size, regardless of mass. If it shows a tonnage, it is compulsory only when the vehicle's or combination's MMA exceeds that figure. At this sign, you must choose that carriageway to continue your journey; its purpose is to assign you a compulsory route. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-414 requires you to use the indicated carriageway when you carry dangerous goods and must display the specific signs or markings; R-416 refers to explosive or readily flammable goods under those conditions. You must read the specific symbol: not every blue sign with a lorry applies to the same vehicles. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-415 requires you to use the indicated carriageway if you carry more than 1,000 litres of products capable of polluting water. You must compare the volume with that threshold, without converting it into tonnes. R-110 prohibits entry with that type of product; R-415 establishes the compulsory route. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • You must respect routes reserved for and compulsory for pedestrians, cycles, mopeds or VMP when they exclude other vehicles. The carriageway appearing wide enough does not authorise access for your lorry. You must always check whether the sign establishes a requirement, a reservation or both. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

19Compulsory equipment and end signs

A truck travels in its lane with snow chains on its visible rear wheel beside a mandatory snow chains sign in a snowy landscape.
The key idea

Use compulsory equipment and check which restriction ends.

End signWhat ends
R-506Signed minimum speed
R-500Previous specific prohibitions for moving vehicles
R-501Signed maximum speed
R-502Overtaking prohibition
R-503Overtaking prohibition for lorries
R-509Compulsory carriageway for lorries, tractor units and vans

Remember

  • At R-412, use chains, approved devices or the specified special tyres.
  • Fit chains on at least one wheel per side of the same driven axle.
  • At R-412b, you must use winter tyres.
  • At R-413, use at least dipped headlights.
  • At R-418, you need suitable electronic toll equipment that works.
  • After an end sign, keep obeying general rules.

Exam trap: Wrong: Carrying stored chains always satisfies R-412. Right: Use chains, approved devices or the specified special tyres.

Read the full explanation
  • R-411 imposes the minimum speed shown, subject to the regulatory safety exceptions. R-506 ends that signed minimum; it does not allow unrestricted speed or remove the applicable general minimum speeds. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-412 requires chains or approved anti-skid devices acting on at least one wheel on each side of the same drive axle, or the specified special tyres. R-412b requires winter tyres. To continue, you must use the equipment required by the specific sign. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-413 requires you to drive with at least dipped beam on, even in good visibility. Its end does not remove other reasons that require you to use it. R-418 requires suitable, working electronic toll equipment for that lane: you must check it before entering, without relying solely on number plate recognition. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-500 ends the previous specific prohibitions for moving vehicles; it does not remove general rules or parking prohibitions. R-501 ends the signed maximum speed limit. You must then apply the rules that remain in force for your lorry and the road. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • R-502 ends the overtaking prohibition; R-503 ends the overtaking prohibition for lorries. You must still check markings, visibility and all other conditions before overtaking. R-509 ends the compulsory carriageway for lorries, tractor units, large vans and light vans; it does not make every nearby access a permitted route. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

20Road information and recommendations

A truck with a green cargo box and orange cab travels in the right-hand lane of a road beside a blue motor-vehicles-only sign bearing a white car pictogram.
The key idea

Distinguish recommendations from compulsory limits and reserved uses.

SignWhat it means
S-7Recommended maximum speed
S-9Recommended speed range
S-32Electronic toll payment available alongside other methods
R-418Electronic toll payment compulsory

Remember

  • You may use motor-vehicle roads if no other restriction excludes your lorry.
  • Adapt recommended speeds to weather and your lorry’s limits.
  • Recognise S-5 as a tunnel, underpass or equivalent section.
  • Use escape lanes only for braking problems.
  • Read parking reservations and conditions.
  • Do not unload your lorry at taxi-only stops.

Exam trap: Wrong: Recommended speeds let you exceed your lorry’s limit. Right: Obey the compulsory limit.

Read the full explanation
  • S-1 identifies the start of an autopista (motorway); S-1a, the start of an autovía (dual carriageway); S-3, a road reserved for motor vehicles. You may enter the latter with your lorry if no other restriction prevents it. It is not limited to cars and does not itself impose a maximum MMA (maximum authorised mass) of 3,500 kg; nor does it turn a conventional road into a motorway. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • S-5 identifies a tunnel, underpass or equivalent stretch of road. This sign announces specific traffic rules. Lighting is explained in «Lorry lights and signals»; following distances in «Speed and safe following distances»; and tunnel emergencies in «Accidents, breakdowns and first aid». [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • S-7 recommends a maximum speed and S-9 an advisable range, for example from 70 to 90 km/h, in favourable conditions. You must adapt your driving to the conditions and obey any lower mandatory limit. The recommendation does not authorise you to exceed your lorry's own maximum speed or require you to maintain the recommended speed in bad weather. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • S-16 identifies an escape lane for stopping vehicles with braking problems. You may use it as an emergency measure if your brakes fail. S-32 indicates that electronic toll payment is available alongside other payment methods; you must distinguish it from the compulsory electronic toll payment indicated by R-418. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • S-17 indicates parking and you must read its reservations and conditions. S-18 reserves stopping and parking for taxis that are available for hire and on duty: you cannot use it to unload your lorry. A service sign does not make every nearby space available for stopping or parking your vehicle. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

21Lanes, mountain passes and directions

A truck travels in the right lane of a divided motorway approaching a fork marked by a blue sign with two separate arrows, one straight and one to the right.
The key idea

Plan your route and check restrictions for each lane and exit.

Direction informationWhat it tells you
Direction signsWhere to go
Road identification signsWhich road you are using
Confirmation signsDestinations and distances

Remember

  • Read restrictions shown within lane diagrams.
  • VAO lanes are prohibited for your lorry, regardless of how many people are inside.
  • At S-21, check mountain pass conditions and every restriction.
  • Choose your exit lane in good time.
  • Check that you may use each branch before entering.
  • An advertised service does not guarantee parking space for your lorry.

Exam trap: Wrong: Every rectangular sign gives advice. Right: It may include compulsory restrictions.

Read the full explanation
  • You must read lane signs using their diagrams: the number of lanes, directions of travel, merging or ending lanes, and restrictions shown within them. An information sign may include a mandatory maximum speed, minimum speed or prohibition. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • You must not use the VAO (high-occupancy vehicle) lane with your lorry, regardless of its occupancy [RGC, art. 35.2.a](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a35), as amended by [RD 518/2026](https://www.boe.es/buscar/doc.php?id=BOE-A-2026-13889); see «Reserved lanes and special traffic arrangements» in «Manoeuvres with a lorry» and «Lanes with specific limits» in «Speed and safe following distances».
  • S-21 provides information on whether a stretch of road or mountain pass is open to traffic. You must interpret the road status, lorry restrictions, equipment requirements and the point where they begin together. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • You must use advance direction signs to prepare your lane choice and route in good time. Direction signs guide you towards destinations; road identification signs show which road you are on; confirmation signs remind you of destinations and distances. With a lorry, you must also check the restrictions on each branch before committing to an exit. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Service signs may indicate fuel, charging, assistance, food or rest facilities; you must distinguish the advertised service from the actual possibility of parking a vehicle of your dimensions. Location signs identify built-up areas, boundaries or places: you must relate them to the rules associated with them. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

22Road layout and surface hazards

A truck travels in the right lane of a road bending to the right, beside a triangular warning sign for a dangerous right-hand bend.
The key idea

Prepare for bends, slopes and surface changes before reaching them.

10 %Example gradient
10 mExample height difference
100 mExample horizontal distance
Hazard signsWhat you must distinguish
P-16a and P-16bSteep descent and ascent, respectively
P-19 and P-28Slippery surface and loose chippings
P-33 and P-34Reduced visibility and frequent ice or snow

Remember

  • Check which way the first bend turns.
  • Do not assume a warning picture sets a fixed speed.
  • Read slope figures as percentages.
  • Prepare for changes affecting how your vehicle and load are supported.
  • Take particular care with crosswinds in your lorry.

Exam trap: Wrong: 10 % means ten degrees. Right: It means 10 m height difference per 100 m horizontally.

Read the full explanation
  • P-13a and P-13b warn of a dangerous bend to the right and left. P-14a and P-14b announce a series of bends close together, with the first to the right and left respectively. You must prepare your lorry's approach and identify the first bend, without inferring a fixed speed from the diagram. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-16a warns of a steep descent and P-16b of a steep ascent. The figure indicates the gradient as a percentage relative to the horizontal: 10 % means a change in height of 10 m for every 100 m horizontally. It is not a speed, a remaining distance or an angle in degrees. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-15 warns of an uneven road; P-15a, a hump; P-15b, a dip. You must anticipate changes in how the vehicle and load are supported. P-19 warns of a slippery road surface and P-28 of loose chippings: you must distinguish loss of grip from materials that may be thrown up. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-26 warns of possible falling rocks and obstructions; P-30, a step or drop at the side of the road. You must pay attention to the space available for your lorry's wheels. P-25 warns of two-way traffic, so you must not continue assuming that the full width of the carriageway is for your direction of travel. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-29 warns of crosswinds, which are particularly relevant because of your lorry's size. P-33 warns of reduced visibility; P-34, frequent ice or snow. You must adapt your driving to both visibility and grip; these warnings do not themselves set a numerical speed limit. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

23Traffic hazards and vulnerable road users

A truck approaches a triangular warning sign announcing a pedestrian crossing, while an adult woman and a child wait on the pavement beside the crossing.
The key idea

Prepare for junctions, queues and road users who need extra care.

WarningWhat you must expect
Pedestrians, children or people with difficultiesYou need to watch particularly carefully
CyclistsPossible crossings or frequent cycle traffic
AnimalsAnimals may suddenly enter the road
Level crossings or movable bridgePossible closures
Congestion or obstructionStationary vehicles or obstacles

Remember

  • Check areas your lorry may hide from view.
  • Adjust your driving before you see the obstacle.
  • Distinguish cycle warnings from signs marking an actual crossing.
  • Check the signs and markings that determine priority.
  • Do not enter a crossing where you could become trapped.
  • Read plates explaining other hazards.

Exam trap: Wrong: Every triangular sign requires you to stop. Right: Distinguish warnings from rules controlling passage.

Read the full explanation
  • P-3 warns of traffic lights ahead; P-4, a roundabout; P-31, congestion; P-32, an obstructed carriageway. You must anticipate stationary vehicles before reaching the indicated point. P-35 warns of weaving traffic, where lane-changing paths may cross between a merge and a split. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-20a warns of pedestrian crossings; P-20b, an area with frequent pedestrian traffic; P-20c, pedestrian and cycle crossings. P-21a warns of children and P-21b of people with mobility or sensory difficulties. You must be especially observant, taking into account the areas your lorry may hide from your view. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-22a warns of cycle crossings and P-22b of frequent cycle traffic. These signs allow you to anticipate cyclists before the point where your paths may conflict. Actual priority is determined by the applicable rules and markings; you must not treat every triangular warning sign as an order to stop. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-23 warns of domestic animals or livestock; P-24, wild animals, and P-24a highlights the danger of wild boar. P-50 warns of other dangers without a specific sign. You must check the explanatory plate and anticipate something suddenly entering the road, without waiting to see the obstacle before adapting your driving. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • P-7 and P-8 warn of level crossings with and without barriers; P-11 and P-11a identify crossings without barriers, with one or several railway tracks. P-5 warns of a movable bridge and P-6 of a tram crossing. You must anticipate closures and must not enter a crossing where your lorry may become stuck. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

24Supplementary plates and emergencies

A rigid truck travels in its lane beside a road narrowing warning sign with a supplementary panel showing a truck pictogram.
The key idea

Read the sign and its plate as a single message.

200 mExample distance or section length
PlateWhat it indicates
S-800Distance to the start
S-810Length of the affected section
S-880bApply the main sign only to vehicles towing trailers, except single-axle trailers

Remember

  • With S-880a, apply the main sign only to lorries.
  • EXCEPTO above the lorry picture means that category is excluded.
  • Read times, conditions and exit branches before deciding.
  • Follow the indicated priority-road route, even when it turns.
  • Use emergency exits to evacuate people.
  • Do not confuse an emergency exit with a driving exit for your lorry.

Exam trap: Wrong: Confuse distance to a hazard with its length. Right: Distinguish the plates.

Read the full explanation
  • S-800 indicates the distance to the start of the hazard or requirement; S-810, the length of the affected stretch. With 200 m on S-800, you have 200 m to go before the start; with that figure on S-810, the affected stretch is 200 m long. Below a road-narrowing warning, check whether the plate shows the clear width available. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • S-880a indicates that the upright sign it accompanies applies exclusively to lorries. S-880b, «Application of signs to vehicles with trailers except single-axle trailers», restricts its application to vehicles with trailers, except single-axle trailers: it applies to you if you drive a lorry with a two-axle trailer. You must obey the main sign's instruction. If EXCEPTO (EXCEPT) appears above a pictogram, you must interpret it as excluding the category shown. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Plates may specify times, weather conditions or exit branches. You must read the full inscription before comparing your vehicle's category or mass. Priority road diagrams show its course: you must not assume that priority requires you to continue straight ahead if the main road turns. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • S-960 identifies an emergency telephone; S-980, an emergency exit, and S-990a and S-990b, «Emergency exit ahead», indicate the direction and distance to the nearest emergency exit. You must interpret the arrow and distance as evacuation guidance for people, without confusing it with a normal exit you can take while driving your lorry. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Enforcement signs identify monitoring of speed, traffic lights, STOP signs or following distances; chevron signs or marker posts help you estimate distance. An enforcement sign does not authorise you to break the rules outside the monitored location. Telephone and fire extinguisher pictograms identify that equipment, not an exit or a medical station. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

25Longitudinal lines and arrows

A truck with a green cab and orange box body travels in its right-hand lane beside a solid white centre line on a rural road.
The key idea

Follow the line on your side and obey your lane’s arrows.

LinesWhat they mean
BrokenDivide lanes; you may make permitted manoeuvres
SolidDo not cross or drive along them, except where rules allow
Double brokenMark reversible lanes
Advance warning brokenWarn of a solid line or particularly risky section

Remember

  • Cross broken lines only for permitted manoeuvres, when safe.
  • Do not cross solid lines, except where the rules allow.
  • With solid and broken lines together, follow the line on your side.
  • After overtaking from the broken-line side, you may cross the solid to return.
  • At return arrows, abandon overtaking or finish as soon as safely possible.
  • When your lane ends, merge while respecting traffic already in the other lane.

Exam trap: Wrong: Broken lines always allow overtaking. Right: Check signs, visibility and rules too.

Read the full explanation
  • Broken lines M-1.1 to M-1.3 mark lane boundaries and allow you to cross them for permitted manoeuvres, giving way to anyone already occupying the space you intend to enter. You must not drive along these lines unless the width of the lanes makes it necessary and you can do so safely. A broken line does not authorise overtaking where a sign, visibility conditions or a rule prohibit it. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • You must not cross or drive along solid lines M-2.1 to M-2.3, except where the regulations allow it. If they separate opposing directions of traffic, you must not drive to their left. Two parallel solid lines have the same meaning as one. Edge lines mark the limits of the carriageway, and their appearance does not change the rules governing use of the arcén (hard shoulder). [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Where a solid line runs alongside a broken line, M-3.1 to M-3.3, you must obey the line on your side. If the marking separates opposing directions and you overtake from the broken-line side, you may cross the solid line to return after completing or abandoning the manoeuvre. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Double broken lines M-1.4 and M-1.5 mark the boundaries of reversible lanes controlled by traffic lights or other means. Warning broken lines M-1.9 and M-1.10 indicate an approaching solid line or a section with a particular risk. You recognise the warning by the pattern of dashes and gaps, whereas a reversible lane is bounded by double broken lines. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Lane arrows indicate the movements permitted or compulsory in the lane. M-5.4 warns that the lane ends and requires you to merge, giving way to anyone already occupying the space you intend to enter; M-5.5, the return arrow, warns of an approaching solid line that prohibits driving to its left: do not start overtaking, or complete the manoeuvre as soon as you can safely. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

26Transverse lines and crossings

A truck remains entirely behind a solid transverse stop line spanning its lane at a red traffic light.
The key idea

Stop at the correct place and give way to pedestrians and cyclists.

MarkingWhat you must do
Solid transverse lineStop before it when required to stop
Broken transverse lineDo not proceed while required to give way
Pedestrian crossingLet pedestrians cross according to the rules
Cycle crossingGive way to cyclists; follow officers and traffic lights

Remember

  • When you must stop, keep your lorry and load behind the line.
  • If visibility is poor, stop again where you can see without causing danger.
  • Link broken transverse lines to your duty to give way.
  • At crossings with traffic lights, follow their signals.
  • Apply painted STOP and give way messages to the lane containing them.
  • A painted speed figure sets a maximum for that lane.

Exam trap: Wrong: Every broken transverse line always requires a stop. Right: Check the priority requirement.

Read the full explanation
  • M-4.1 is the solid transverse stop line. You must not allow your lorry or its load to cross it when you must stop for a STOP sign, traffic lights, a traffic officer or another reason specified in the regulations. To make a second stop because of insufficient visibility, apply the guidance in «STOP, give way and priority road». [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • M-4.2, a broken transverse line, marks the point beyond which you must not proceed while you have to give way, except in the exceptional visibility circumstances specified in the regulations. The marking alone does not require you to stop every time. You must interpret it together with the sign or priority rule that requires you to give way. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • M-4.3 identifies a pedestrian crossing through stripes parallel to the centre line of the carriageway, forming a group across it. You must let pedestrians cross in accordance with the regulations. A crossing controlled by traffic lights may use two broken transverse lines: you must obey the traffic lights, rather than relying only on the similarity of the markings. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • M-4.4 identifies a cycle crossing through two parallel broken transverse lines, where you must give way to cyclists. It may be supplemented by coloured surfacing and variants provided for in the catalogue. Priority does not depend on the cyclist approaching from your right; check for traffic officers and traffic lights controlling the crossing. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • The painted STOP marking, M-6.3 or M-6.4, and the give-way marking M-6.5 apply to the lane in which they are placed. A speed figure painted on the road imposes a maximum speed in the lane concerned. You must resolve any conflicts with upright signs by applying the hierarchy, and continue to obey instructions that are compatible. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

27Reserved areas, parking markings and colours

A truck with an orange cab and green cargo box travels in its lane beside a white hatched area enclosed by a solid line, without entering it.
The key idea

Respect reserved areas and distinguish the bans shown by yellow markings.

Yellow markingWhat it prohibits
Broken longitudinal lineParking
Solid longitudinal lineStopping and parking
ZigzagParking: the space is reserved for a special use

Remember

  • Do not use solid-bordered hatching to overtake or wait in your lorry.
  • Do not enter a box junction if you would block crossing traffic.
  • Do not stop or park on access to an escape bed.
  • Respect reserved spaces even if your lorry fits.
  • At traffic lights, stop at the line for your vehicle.
  • Do not assume every coloured surface imposes a prohibition.

Exam trap: Wrong: Any lorry may unload on a zigzag. Right: Check the reserved use and its conditions.

Read the full explanation
  • You must not enter a hatched area M-7.1 or M-7.2 enclosed by a solid line, unless you are a road user required to use the hard shoulder. You cannot use it in your ordinary lorry to overtake, wait or cut a corner. You must distinguish an excluded area from a tapered area designated for merging. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • The broken yellow longitudinal line M-7.7 prohibits parking along its entire length on that side. The solid yellow line M-7.8 prohibits stopping and parking. If the prohibition is temporary, you must read the upright sign specifying the period; do not assume an exception applies because you are driving outside business hours. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • The yellow zigzag line M-7.9 prohibits parking because the space is reserved for a special use without a prolonged stay, such as bus stops or loading and unloading. On its own, it does not prohibit every stop or authorise any lorry to unload: you must check the reserved use and the conditions at the location. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • The box marking M-7.10 reminds you that you must not enter a junction if you are likely to stop and obstruct crossing traffic, even if you have a green light or priority. The red and white chequered marking M-7.11 marks the entrance to an escape bed: you must not stop, park or use that surface for other purposes. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Parking markings define parking bays and the position of your vehicle; their colours and pictograms may indicate time limits, permitted users or purposes. You must respect reserved spaces even if your lorry fits. At traffic lights with advanced areas reserved for cycles or motorcycles, you must stop before the line that applies to your vehicle. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).
  • Road markings are white except in the specific cases provided for in the catalogue, such as roadworks and yellow prohibition markings. You may encounter shapes in various colours intended to calm traffic that are not road markings. The applicable obligation comes from the prescribed line, symbol or inscription. [RGC, Annex I](https://www.boe.es/buscar/doc.php?id=BOE-A-2025-12199).

Interpreting several signs at the same entrance

Apply the instruction that relates to your lorry and your intended path.

  1. Identify your lorry’s position, lane and intended movement.
  2. Read the main signs, supplementary plates, times and the road users they apply to.
  3. Check whether the instructions complement or contradict each other.
  4. If they contradict each other, apply the higher-ranking instruction; within the same type, apply the most restrictive.
  5. Follow compatible instructions and check that you can carry out the movement safely.

Checking a restriction for your lorry

Select the correct measurement before deciding whether you can proceed.

  1. Identify whether the restriction concerns a category, goods, MMA, laden mass, an axle or a dimension.
  2. For R-107, use MMA; for R-201, actual mass; for R-202, mass per axle.
  3. For R-203, R-204 and R-205, include the load when checking length, width and height.
  4. Compare with the stated figure, distinguishing between equalling and exceeding it.
  5. Check the other prohibitions and your route before entering.

Obeying a STOP sign with limited visibility

Your initial stop and observation must respect the marked stopping point.

  1. Bring your lorry to a complete stop before the line or, if there is no line, immediately before the intersecting carriageway.
  2. Give way to vehicles on the priority road.
  3. If you cannot see well enough, move forward cautiously and stop again where you can see safely.
  4. Move off when you can complete the whole movement safely.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1Can delineation signs also indicate obstacles on a road?
2If a traffic officer raises an arm vertically and we cannot stop our vehicle safely…
3In 2026, a lorry registered in Spain is immobilised by a breakdown on a one-way urban road. How should the danger be signalled?
4Without a supplementary panel indicating another distance, a regulatory sign’s obligations, restrictions or prohibitions begin to apply from…

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module