Theory · C Licence - Truck · Module 7 of 18

Speed and safe following distances

You learn to choose your lorry’s speed on each type of road and adjust it to the load, visibility and grip. You distinguish between reaction, braking and stopping distances, and apply minimum speeds, the 50-metre gap and tunnel following distances.

32 min read24 sectionsReviewed Nov 3, 2026
A green truck follows an orange car with a wide gap on a two-way rural road.
Maintain a safe following distance

1Legal speed and appropriate speed

A truck with an orange cab and green cargo box travels in its right-hand lane toward patches of ice and a fog-covered bend on a rural road.
The key idea

Choose a speed that lets you control the lorry and stop in time.

Remember

  • Keep within the limits, but slow down further if there is danger.
  • Consider your condition, load, traffic and the weather.
  • Check the lorry, road and signs.
  • You must be able to stop within the clear space you can see.

Exam trap: Wrong: any speed below the limit is safe. Right: adjust your speed to the danger.

Read the full explanation
  • The maximum speed is the upper limit; the minimum prevents you from driving abnormally slowly without justification. You must choose an appropriate speed that allows you to control your lorry and stop for an obstacle within your field of vision. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45) [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • You can be driving at an inappropriate speed even when you do not exceed any maximum limit. If you drive at 70 km/h on an icy conventional road, staying below the lorry limit of 80 km/h does not guarantee safety. Slow down as much as grip, visibility, traffic and the vehicle’s response require. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • Take account of your physical and mental condition, the condition and characteristics of your lorry and its load, the road layout and surface, the weather and traffic. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

2Motorways and dual carriageways: 90 km/h

A rigid truck with an orange cab and green cargo box travels in the right lane of a motorway with a central barrier and the opposite carriageway in the background.
The key idea

Outside built-up areas, your maximum is 90 km/h on motorways and dual carriageways.

90 km/hLorry maximum
Vehicle outside built-up areasMaximum on motorway or dual carriageway
Lorry or tractor unit90 km/h
Motorhome over 3,500 kg maximum authorised mass90 km/h

Remember

  • Keep to this maximum even when the lorry is empty.
  • The same maximum applies to tractor units.
  • With a motorhome over 3,500 kg, keep to 90 km/h too.
  • Obey signs showing a lower limit.
  • Slow down further if conditions require it.

Exam trap: Wrong: you can go faster when empty. Right: the lorry's maximum does not change.

Read the full explanation
  • Outside built-up areas, when you drive an ordinary lorry, your general maximum speed is 90 km/h on both autopistas (motorways) and autovías (dual carriageways), even if a general sign allows other vehicle categories to travel faster. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • The 90 km/h limit also applies when you drive a tractor unit or a motorhome with an MMA (maximum authorised mass) exceeding 3,500 kg; these motorhomes have the same maximum speeds as lorries in this table. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • Driving without a load does not change your lorry’s general maximum speed. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • If you encounter a 70 km/h limit for roadworks, keep to 70; if conditions require a lower speed, slow down further. [RGC, art. 47](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a47) [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

3Conventional roads: 80 km/h

A rigid truck with a green cab and orange cargo box travels in its right-hand lane on a conventional road with a paved shoulder and a Mediterranean landscape.
The key idea

On a surfaced conventional road, your general maximum is 80 km/h.

80 km/hLorry maximum
Vehicle on surfaced conventional road outside built-up areasGeneral or authorised maximum
Lorry or motorhome over 3,500 kg maximum authorised mass80 km/h
Car, motorcycle or motorhome up to 3,500 kg maximum authorised massUp to 100 km/h if the road authority sets it with physical separation

Remember

  • A wide hard shoulder does not raise the limit.
  • A divider between directions does not raise it either.
  • A road reserved for motor vehicles can still be conventional.
  • With a motorhome over 3,500 kg, keep to 80 km/h too.
  • Obey lower signs and slow down if there is danger.

Exam trap: Wrong: several lanes let you go faster. Right: your general maximum remains 80 km/h.

Read the full explanation
  • Outside built-up areas, your general maximum speed on a surfaced conventional road is 80 km/h, even if the arcén (hard shoulder) is wide or surfaced, or there are two lanes in your direction. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • On conventional roads with a physical barrier separating the directions of traffic, the road authority may set a limit of 100 km/h exclusively for cars, motorcycles and motorhomes with an MMA not exceeding 3,500 kg. When you drive a motorhome over 3,500 kg, you have the same maximum speed of 80 km/h as when you drive a lorry. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • When you drive your lorry on a conventional road reserved for motor vehicles, your maximum speed is 80 km/h. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • Always check for lower limits on the section of road. If a bend has a 60 km/h limit, enter it within that limit and at a speed suited to your load, grip and visibility. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45) [RGC, art. 47](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a47)

4Unsurfaced roads: 30 km/h

A rigid truck with an orange cab and green cargo box travels on the right side of a dirt and gravel road beside a rural farm.
The key idea

On an unsurfaced road, you must not exceed 30 km/h.

30 km/hMaximum on unsurfaced road

Remember

  • Slow down further for mud, potholes, dust or gravel.
  • Avoid throwing stones or mud at other people.
  • Look at the carriageway surface, not just the hard shoulder.
  • Do not automatically subtract the dangerous-goods reduction on this road.

Exam trap: Wrong: an earth hard shoulder makes the whole road unsurfaced. Right: check the carriageway.

Read the full explanation
  • Outside built-up areas, your lorry’s maximum speed on an unsurfaced road is 30 km/h, including on access roads to working sites or loading areas with little traffic. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • Check the carriageway surface. If the carriageway of a conventional road is surfaced and only the hard shoulder is dirt, the dirt shoulder does not make the carriageway an unsurfaced road or impose the 30 km/h maximum on it. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • When you encounter potholes, mud, dust or gravel, slow down according to grip and visibility, and avoid throwing up material onto other road users. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45) [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • The reduction of ten kilometres per hour for dangerous goods refers to the table in article 48.1.a. On unsurfaced roads, your maximum remains 30 km/h. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

5Urban roads: 20, 30 and 50 km/h

A box truck with a green cab travels to the right along an urban shared-surface street, beside two pedestrians walking on the paved area at the same level as the roadway.
The key idea

In town, check the pavement level and the lanes in each direction.

20 km/hCarriageway and pavement at the same level
30 km/hOne lane each way
50 km/hSeveral lanes each way
Type of urban roadGeneral maximum for ordinary lorry
Pavement and carriageway at the same level20 km/h
One lane in each direction30 km/h
Two or more lanes in each direction50 km/h

Remember

  • Do not count reserved lanes, such as a bus-only lane.
  • The lorry's weight alone does not lower these limits.

Exam trap: Wrong: you count a bus-only lane. Right: count only lanes that are not reserved.

Read the full explanation
  • On an urban road where the carriageway and pavement form a single level surface, your general maximum speed is 20 km/h. The carriageway and pavement are at the same level; this layout requires you to pay particular attention to people who may approach your lorry’s path. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • On urban roads with only one lane in each direction, your general maximum speed is 30 km/h. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • On urban roads with two or more lanes in each direction, the general maximum speed is 50 km/h. When you drive an ordinary lorry, having an MMA exceeding 3,500 kg does not in itself reduce that limit to 40 km/h. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • When counting lanes, you must exclude those reserved for certain users and those exclusively for public transport. For these purposes, a street with one ordinary lane and one bus-only lane in each direction counts as having one lane in each direction, with a general maximum speed of 30 km/h. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)

6Municipal rules and stretches of road through towns

A rigid truck travels to the right in its lane on a village through-road with tiled-roof buildings on both sides of the road.
The key idea

Check signs; distinguish a road through a town (travesía) from a motorway in built-up areas.

50 km/hGeneral maximum on through road
80 km/hMotorway in built-up area
90 km/hLorry ceiling if raised
Road in built-up areaGeneral maximum for ordinary lorry
Road through a built-up area50 km/h
Motorway or dual carriageway80 km/h

Remember

  • The local authority can lower limits with signs.
  • Exceptionally, it can sign 50 km/h on a one-lane-each-way street.
  • On a through road, obey any lower signs.
  • A higher motorway limit in town needs agreement and signs.

Exam trap: Wrong: you ignore a lower sign on a through road. Right: obey the signed limit.

Read the full explanation
  • The municipal authority may lower general urban speed limits by putting up specific signs. Exceptionally, it may also raise the limit on a road with only one lane in each direction to 50 km/h, with signs. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • On a travesía (the stretch of road through a town), the general maximum speed is 50 km/h for all vehicle types, subject to any applicable specific limits. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • The limit on a stretch of road through a town may be lowered by agreement between the municipal authority and the road authority, with specific signs. If you encounter a signed limit of 30 km/h, obey it even if you remember that the general rule for a stretch of road through a town is 50. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • On motorways and dual carriageways within built-up areas, the general maximum speed is 80 km/h. It may be raised by agreement and with signs, without exceeding the corresponding general limit outside built-up areas: for your ordinary lorry, that upper limit is 90 km/h. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50) [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

7Dangerous goods and other restrictions

A truck with a blank orange ADR panel on its front travels in its right-hand lane on a rural two-way road.
The key idea

With dangerous goods, use their limits and obey lower signs.

10 km/hReduction to interurban table
80 km/hMotorway and dual carriageway
70 km/hSurfaced conventional road
40 km/hThrough roads and multi-lane streets
Road or lorry authorisationMaximum for this transport
Motorway or dual carriageway outside built-up areas, dangerous goods80 km/h
Surfaced conventional road, dangerous goods70 km/h
Through road, dangerous goods40 km/h
Street with two or more unreserved lanes each way, dangerous goods40 km/h
Group 1 special transport: generic permit70 km/h
Group 1 special transport: specific permit60 km/h
Group 1 special transport: exceptional permitSet speed, up to 60 km/h

Remember

  • Do not subtract the reduction from every sign.
  • On streets with one lane each way, keep to 30 km/h.
  • Where pavement and carriageway are level, keep to 20 km/h.
  • For special transport, check your permit conditions.
  • For special transport, also obey lower restrictions on the vehicle test card.

Exam trap: Wrong: you subtract ten from any sign. Right: compare your own maximum with the sign.

Read the full explanation
  • If you carry dangerous goods, you must reduce the maximum speeds in the interurban table by 10 km/h according to the vehicle and road. For your lorry, this gives 80 km/h on motorways or dual carriageways and 70 km/h on surfaced conventional roads. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • On urban roads with two or more lanes per direction that count towards the limit, and on a stretch of road through a town, you must observe 40 km/h when carrying dangerous goods. On streets with a shared carriageway and pavement level and streets with one lane per direction, you must observe the lower limits of 20 and 30 km/h respectively. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • The reduction of ten applies to the maximum speeds in the interurban table. If you drive your lorry carrying dangerous goods on a conventional road with a signed limit of 50 km/h, you combine its own maximum of 70 with the sign: the applicable maximum on that stretch is 50 km/h. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48) [RGC, art. 52](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a52)
  • For special transport in group 1 of Annex III, your maximum speeds are 70 km/h with a general authorisation, 60 km/h with a specific authorisation and the specified speed, up to 60 km/h, with an exceptional authorisation; any lower restrictions on your tarjeta ITV (vehicle roadworthiness test card) take precedence. See the authorisation conditions in «Lorry dimensions and masses», section «Conditions for special transport». [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48) [RGC, Annex III, group 1.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii)

8Signs, overtaking and the speed limiter

A truck follows a car in the right-hand lane of a rural road beside a sign prohibiting overtaking by trucks.
The key idea

Keep to the maximum even when overtaking or using a speed limiter.

90 km/hTrailer maximum on motorway
80 km/hMaximum on conventional road
30 km/hExtra speed allowed for tests
Lorry towing a trailerGeneral maximum
Motorway or dual carriageway outside built-up areas90 km/h
Conventional road outside built-up areas80 km/h

Remember

  • Without a sign, your vehicle and road still set a limit.
  • Do not exceed the maximum to overtake.
  • The limiter does not set the permitted speed for each stretch.
  • With a trailer, obey any specific restrictions too.
  • For tests, you need a permit and must follow its route.
  • That permit excludes urban roads, through roads and stretches with specific speed signs.

Exam trap: Wrong: the limiter always lets you drive at 90 km/h. Right: obey the limit that applies.

Read the full explanation
  • Observe the specific limits for the stretch of road and any temporary or variable limits, together with your vehicle’s maximum speeds and any applicable restrictions on you as a driver or on the transport operation. [RGC, art. 47](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a47) [RGC, art. 52](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a52)
  • You must not exceed the maximum speed to overtake. With an ordinary lorry, you cannot carry out the manoeuvre at 90 or 100 on a conventional road with a generic maximum of 80 km/h. Assess whether you can complete it legally with a sufficient speed difference, and do not attempt it when you cannot. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48) [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)
  • Your speed limiter setting does not authorise you to exceed the speed permitted on the road; its technical requirements are explained in «Lorry dimensions and masses», section «Speed limiters». [RD 1417/2005, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a4) [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • With a special permit for testing, you may exceed the maximum speeds by up to 30 km/h only on the authorised route; urban roads, any stretch of road through a town and stretches with specific speed-limit signs are excluded. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • If you tow a trailer permitted by your driving entitlement, the table for motor vehicles towing trailers also sets 90 km/h on motorways and dual carriageways and 80 on conventional roads. The trailer’s mass does not create a different generic maximum in that table. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

9General minimum speeds

A truck with a green cab and orange cargo box travels in the right lane of an empty motorway, with the opposite carriageway separated by a central barrier.
The key idea

Without good reason, you must also keep to a minimum speed.

60 km/hMotorway minimum
40 km/hMinimum on conventional road
15 km/hMinimum on unsurfaced road
Road for ordinary lorryMinimum without good reason
Motorway or dual carriageway60 km/h
Conventional road40 km/h
Unsurfaced road15 km/h
Urban road with general maximum of 20 km/h10 km/h
Urban road with general maximum of 30 km/h15 km/h
Urban road with general maximum of 50 km/h25 km/h

Remember

  • On motorways and dual carriageways, do not calculate half the lorry's maximum.
  • On other roads, use half the general maximum for your vehicle category.
  • A lower maximum sign does not change the reference for this calculation.
  • If there is danger, you may need to slow down further or stop.

Exam trap: Wrong: you calculate 45 km/h on a motorway. Right: the general minimum is 60 km/h.

Read the full explanation
  • On motorways and dual carriageways, you must not drive your lorry below 60 km/h without a justified reason, even when there are no other vehicles. The minimum is not half its maximum of 90 km/h: these roads have their own minimum speed for motor vehicles. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • On other roads, your minimum speed is half the generic speed limit of your vehicle category on that road. For your ordinary lorry on a conventional road, this gives 40 km/h, half of 80; if you drive at 30 without justification, you are below that minimum. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • On an unsurfaced road with a generic maximum of 30 km/h, half is 15 km/h. On ordinary urban roads with generic limits of 20, 30 and 50, the corresponding halves are 10, 15 and 25 km/h. You apply these calculations subject to the safety and traffic exceptions explained below. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • If a sign sets a lower maximum speed, you still use the generic limit to calculate the minimum; the justified reasons for driving more slowly are explained in the next section. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)

10When you can drive more slowly

A three-axle truck with its hazard lights on follows two cars within the right-hand lane of a rural road.
The key idea

You can go below the minimum when going faster would be dangerous.

3,500 kgAuthorised mass threshold

Remember

  • You may go below the minimum for ice, queues or breakdowns.
  • If below the minimum and at risk from behind, switch on your hazard lights.
  • With a lorry above 3,500 kg MMA, stay on the carriageway.
  • If you escort another vehicle for its protection, match its speed.

Exam trap: Wrong: a slow lorry over 3,500 kg must use the hard shoulder. Right: stay on the carriageway; use the hard shoulder only in an emergency.

Read the full explanation
  • You may drive below the minimum if traffic, vehicle or road conditions prevent you from maintaining a higher speed safely. A traffic queue, ice or a breakdown may justify this. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • The regulations also provide for special vehicles, special transport and protection or escort duties, where you adapt your speed to the vehicle you accompany. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • If you cannot reach the required minimum and there is a risk of a rear-end collision, switch on your hazard warning lights while driving. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • The duty to use the arcén (hard shoulder) when an emergency makes you drive at an abnormally low speed that seriously disrupts traffic applies to vehicles with an MMA (maximum authorised mass) not exceeding 3,500 kg and requires a usable hard shoulder of sufficient width; your lorry exceeds that threshold. See «Lorry licences and types of transport», section «Specific road-use rules for goods vehicles». [RGC, art. 36.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a36)

11Lanes with specific limits

A truck with its headlights on travels in a temporary contraflow lane opened for roadworks, separated by cones from a car travelling in the opposite direction.
The key idea

Before using a special lane, check whether your lorry may enter it.

60 to 80 km/hRange in the stated cases
CaseWhat to do with your lorry
Opposite direction opened to improve traffic flowDo not enter
Opposite direction opened for roadworksEnter only if authorised on that road and not banned; keep to 60 to 80 km/h
Only adjacent lane left in the normal directionKeep to 60 to 80 km/h
Temporary additional lane and hard shoulders used to create itKeep to 60 to 80 km/h

Remember

  • Obey any lower limit set or shown by signs.
  • Use dipped beam in these lanes by day and by night.
  • If several lanes remain in the normal direction, follow their usual rules.
  • Do not enter lanes for opposing traffic, even to overtake.
  • Do not move signs or barriers that mark out these lanes.

Exam trap: Wrong: keeping to the speed is enough to enter. Right: first check that your lorry is authorised.

Read the full explanation
  • A lane opened in the opposite direction to its normal use to improve traffic flow is reserved for motorcycles and cars without trailers, so you cannot use it with your lorry. The authority may open it on carriageways with more than one lane per direction, using temporary signs. [RGC, art. 41](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41)
  • If the lane is opened because of roadworks, you may use it with your lorry if it is authorised on that road, unless expressly prohibited, under the same driving conditions as the lane opened for opposing traffic. Keep your dipped beam on by day and at night and drive between 60 and 80 km/h, or within any lower limits established or specifically signed. Avoid disturbing fixed or movable delineators. You must not move sideways into lanes for traffic travelling in the opposite direction, even to overtake. [RGC, art. 41](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41)
  • In the lanes travelling in the normal direction alongside the lane opened for opposing traffic, also keep your dipped beam on by day and at night and observe the prohibition on moving sideways into the opposite direction. If only one lane remains for your direction, also observe 60 to 80 km/h, or any lower limits established or signed; if several remain, observe the applicable ordinary maximum and minimum speeds. [RGC, art. 41](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41)
  • A temporary additional lane is opened on a two-way carriageway with hard shoulders if its width allows: temporary delineators change the central running area and both hard shoulders are used to provide two lanes in one direction and one in the other. You may use it with your lorry, following the signs. [RGC, art. 42](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a42)
  • In this additional lane and on the hard shoulders opened to traffic, drive between 60 and 80 km/h, or within any lower limits established or signed, with your dipped beam on by day and at night. You follow the rules in article 41 wherever applicable, including taking care not to disturb the delineators and the prohibition on moving sideways into lanes for traffic travelling in the opposite direction, including when overtaking. [RGC, arts. 41 and 42](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a42)

12Road users and access points that require you to slow down

A truck stops before an unsignalized pedestrian crossing while a woman and a child holding hands wait on the pavement to cross.
The key idea

Slow down before places where people or animals may appear.

Remember

  • Slow down near pedestrians and cyclists; stop if needed.
  • Take special care near children and people with mobility difficulties.
  • Slow down near schools, markets and crossings without lights or an officer.
  • Look ahead for building exits and industrial entrances.
  • Slow down for animals and stopped buses, especially school buses.
  • Outside built-up areas, slow down for stopped vehicles, recovery vehicles at work and cyclists.

Exam trap: Wrong: you wait until someone crosses. Right: slow down first if you can expect them to enter.

Read the full explanation
  • Slow down and even stop for pedestrians in your path or whom you can anticipate stepping into it, especially children, older people, blind people or people with reduced mobility. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • Slow down as you approach cycles, junctions and areas near cycle routes, and pedestrian crossings without traffic-light or traffic-officer control. Also do so near markets, educational establishments and places where you can expect children. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • Slow down if there are animals or you can anticipate them entering the road, and on stretches with buildings that have direct access to it. At an industrial access point, also assess exits and concealed areas: to adapt your speed, you must consider obstacles that you can reasonably expect, even if they are not yet in your lane. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46) [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • As you approach a stationary bus, especially a school bus, slow down. Outside built-up areas, also do so when approaching vehicles immobilised on the carriageway, roadside assistance vehicles in service and cycles on the carriageway or hard shoulder. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)

13Junctions, crossings and visibility

A rigid truck approaches an intersection in its right-hand lane, with a give-way sign and a wall that limits visibility.
The key idea

Slow down when you cannot see well or have little room to pass.

50 km/hMaximum at the stated junction

Remember

  • Slow down near level crossings, roundabouts, junctions without priority and narrow sections.
  • At signposted junctions with almost no visibility, do not exceed this maximum.
  • Slow down further or stop if needed to look and give way.
  • When meeting an oncoming vehicle, consider both vehicles' width and projecting parts.
  • At night, match your speed to the space your lights show.

Exam trap: Wrong: you try to keep 50 km/h at a dangerous junction. Right: slow down further if needed.

Read the full explanation
  • Slow down as you approach level crossings, roundabouts, junctions where you do not have priority, narrow sections and places with reduced visibility. Stop if necessary. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • At properly signposted junctions with virtually no visibility, article 46.1.h sets a maximum of 50 km/h. Slow down further or stop if you need to look and give way, observing any lower limit. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • When meeting an oncoming vehicle, slow down when the road, the vehicles or the weather make it difficult to do so safely. With your lorry on a tight bend, assess the width and projecting parts of both vehicles. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • You must also be able to stop within the distance you can see to be clear on bends, at the crests of hills and at night. If you switch to lights with a shorter range, adjust your speed to the visible distance. The use of lights is explained in «Lorry lights and signals», section «Main beam: range and limits». [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

14Rain, ice and lorry stability

A rigid truck travels in the rain on a wet road and maintains a wide gap behind the car ahead in its lane.
The key idea

In bad weather, slow down and leave more room to stop.

Remember

  • Slow down on slippery roads or when you may splash water or throw gravel.
  • In fog, rain, snow, dust or smoke, match your speed to visibility.
  • Slow down if you are dazzled.
  • Before bends or descents, slow down according to your load and lorry stability.
  • On ice, braking space depends on the available grip.
  • Do not assume a fixed braking distance for a particular speed.

Exam trap: Wrong: below the limit always keeps a loaded lorry in control. Right: match speed to its stability.

Read the full explanation
  • Slow down on slippery surfaces and when you might splash or throw water, gravel or other material onto other road users. When you drive past people or vehicles, the water displaced by your lorry also affects the appropriate speed, even if you still have grip along your path. [RGC, art. 46.1.g](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • In dense fog, heavy rain, snowfall, dust or smoke, adjust your speed to the available visibility and grip. Also slow down if you are dazzled. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46) [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • When deciding your speed, assess the load, stability, gradient and braking capacity. On bends or descents, slow down in advance to maintain control; a speed below the maximum can still be inappropriate for a laden lorry. Descent techniques are covered in «Safe lorry driving», section «Control a long descent». [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • On ice, your braking margin depends on the available grip; avoid assuming a fixed braking distance for a particular speed. Driving on these surfaces is covered in «Safe lorry driving», section «Snow, ice and low-grip surfaces». [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

15Slowing down without causing a rear-end collision

A truck travels in the right lane with its brake lights illuminated while an orange car follows with space between them on a rural road.
The key idea

Before braking hard, check traffic behind and warn it if possible.

Remember

  • Avoid sharp braking unless there is immediate danger.
  • Warn with repeated brake lights or the prescribed arm signal.
  • Also warn when traffic makes you slow down.
  • If danger is immediate, act without delaying to warn.
  • If another vehicle overtakes you, do not speed up or obstruct it.
  • If danger arises, slow down unless the driver stops overtaking and slowing is unsafe.

Exam trap: Wrong: you delay urgent braking to give a warning. Right: act in time to avoid danger.

Read the full explanation
  • Except in imminent danger, before slowing down considerably you must check that you can do so without putting those following you at risk, give advance warning and avoid slowing down abruptly. [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)
  • Whenever possible, you must signal your intention to brake considerably or bring your vehicle to a standstill by repeatedly operating the brake lights or using the prescribed arm signal. You must also give this warning when traffic forces you to slow down; it does not depend on whether you intend to park. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)
  • If you are being overtaken, you must not increase your speed or hinder the manoeuvre. You must slow down if a danger arises during it, subject to the regulatory exception where the overtaking driver abandons the manoeuvre and your slowing down would compromise safety. See «Manoeuvres with a lorry», section «Your duties when being overtaken». [RGC, art. 86](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a86)

16Reaction distance and time

A driver seated on the left of a green truck watches a fallen branch ahead in his lane on a two-way road.
The key idea

Reaction distance is the distance you travel before you start braking.

3.6Divisor to convert speed
25 mAt 90 km/h, one second
22.2 mAt 80 km/h, one second

Remember

  • Reaction time is measured in seconds and distance in metres.
  • For the same reaction time, doubling speed doubles the distance.
  • Divide km/h by 3.6, then multiply by the seconds.
  • These calculations are examples, not required distances.
  • Sleepiness, tiredness, alcohol and distractions can delay your response.

Exam trap: Wrong: you call the distance before braking the braking distance. Right: it is reaction distance.

Read the full explanation
  • Reaction distance is the distance you travel from the moment you perceive a hazard until you begin to apply the brake. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You measure time in seconds and distance in metres. Your reaction time depends on your alertness and condition; your reaction distance also depends on your speed. For the same reaction time, doubling your speed doubles the distance you travel before braking. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • As a learning calculation, you can work out the distance in metres by dividing the km/h by 3.6 and multiplying by the number of seconds. Assuming a reaction time of one second, you travel 25 m at 90 km/h and about 22.2 m at 80 km/h; these are mathematical examples, not mandatory times or legally prescribed distances. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • Sleepiness, fatigue, alcohol or distraction can delay your response and increase the distance you travel before braking. See the factors that affect your response in the module «The driver’s condition», section «Perception and reaction time». [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

17Braking distance

A truck travels to the right on a wet road, with its brake lights illuminated and a clear stretch ahead.
The key idea

Braking distance starts when you press the brake and ends when you stop.

Remember

  • Consider speed, load and how it is placed.
  • Brakes, tyres, suspension and road grip matter too.
  • With the same conditions, doubling speed needs about four times the braking distance.
  • On wet or slippery roads, slow down and leave a bigger gap.

Exam trap: Wrong: doubling speed only doubles braking distance. Right: in the same conditions, it roughly quadruples.

Read the full explanation
  • Braking distance is the distance you travel from the moment you apply the brake until your lorry comes to a standstill. It starts at a different point from reaction distance. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • To assess braking, consider your speed, mass, load and its positioning, brakes, tyres, suspension and grip. The DGT includes these factors in its technical explanation. [DGT, braking distance](https://www.dgt.es/muevete-con-seguridad/evita-conductas-de-riesgo/conducir-con-exceso-de-velocidad/) [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • If conditions and deceleration remain the same, your braking distance increases approximately with the square of your speed: if you double your speed, you need around four times the distance. Distinguish this relationship from reaction distance, which increases in direct proportion to speed for the same reaction time. [DGT, speed and stopping distance](https://revista.dgt.es/es/reportajes/2015/07JULIO/0706-Velocidad-20-preguntas-y-respuestas.shtml)
  • With water or less grip, you may need more braking distance at the same speed. Increase your following distance and slow down. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45) [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)

18Total stopping distance

A truck travels in the right-hand lane toward a fallen branch, with consecutive green and orange sections representing reaction travel and braking travel, separated by a pictogram of a foot over a pedal.
The key idea

To find the distance you need to stop, add reaction and braking distance.

25 mExample reaction distance
40 mExample braking distance
65 mExample stopping distance

Remember

  • Count from when you notice the danger until the lorry stops.
  • A slower reaction increases the total distance.
  • Less grip can increase braking distance even with a quick reaction.
  • Compare the full stopping distance with the clear space you can see.
  • The example figures are not official distances for your lorry.

Exam trap: Wrong: you count only braking. Right: include the distance travelled while reacting.

Read the full explanation
  • Add your reaction distance and braking distance to obtain your stopping distance, also called your technical stopping distance. This covers the distance from the moment you perceive the need to stop until you come to a standstill. [DGT, speed and stopping distance](https://revista.dgt.es/es/reportajes/2015/07JULIO/0706-Velocidad-20-preguntas-y-respuestas.shtml)
  • With a reaction distance of 25 m and a braking distance of 40 m, your stopping distance is 65 m. These are hypothetical figures to illustrate the addition, not a legally prescribed distance for your lorry at a particular speed. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • A delay in your reaction increases your total distance even if you brake just as effectively. A loss of grip increases the braking portion even if you react just as quickly. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • When assessing the visible distance, include both the distance you travel before braking and your braking distance. For example, when you discover a traffic queue beyond a bend, you need a margin from the moment you first perceive the brake lights until your lorry comes to a complete standstill. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

19Following distance to avoid collisions

A green truck travels behind an orange car, maintaining a wide gap between them in the right-hand lane of a two-way road.
The key idea

Leave enough room to avoid hitting the vehicle in front if it brakes suddenly.

5 mBehind cyclist in town
TermWhat it means
Safe following distanceGap between vehicles
Stopping distanceDistance you need to stop

Remember

  • Keep a gap in town and when you want to overtake.
  • Increase it with higher speed, less grip, poor visibility or tiredness.
  • Consider your lorry's load and condition.
  • If someone enters your gap, restore it gradually without dangerous braking.
  • Behind a cyclist in your urban lane, leave more than the minimum if needed.

Exam trap: Wrong: you confuse the gap with stopping distance. Right: distinguish the space between vehicles from the distance needed to stop.

Read the full explanation
  • When you drive behind another vehicle, you must leave enough space to stop without colliding if it brakes suddenly. You must take particular account of your speed and the conditions affecting grip and braking. This obligation applies when you drive your lorry both in towns and on roads outside built-up areas, even if you intend to overtake. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • Increase the gap as your speed increases, grip decreases, visibility worsens or your response may be slower. Also assess your lorry’s condition and load. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45) [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • Your safe following distance is the gap between vehicles; your stopping distance is the distance you need to come to a stop. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • If another vehicle moves into part of the gap you have left, gradually restore a safe following distance without causing dangerous braking behind you. [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53) [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On urban roads, if a cyclist is ahead of you in the same lane, you must leave a following distance of at least 5 m. Increase this gap if you need more space to stop your lorry without colliding. [RGC, art. 153.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a1-6) [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)

20The lorry’s 50-metre gap

A three-axle rigid truck follows a car with a wide empty gap in its lane on a conventional two-way road.
The key idea

When required, leave an extra gap to help others overtake you.

50 mMinimum extra gap
3,500 kgAuthorised mass threshold
10 mTotal length threshold

Remember

  • Either the authorised mass or total length threshold is enough.
  • Your lorry is included because of its authorised mass.
  • Keep the extra gap when required and you are not signalling to overtake.
  • Leave a bigger gap if you need more space to avoid a collision.
  • Exceptions do not remove the gap needed to avoid a collision.
  • Neither queues nor an overtaking ban allow you to follow too closely.

Exam trap: Wrong: both the mass and length thresholds must be exceeded. Right: either one is enough.

Read the full explanation
  • If you follow another vehicle without signalling your intention to overtake, you must also leave enough space for the driver behind you to overtake you safely. If your MMA (maximum authorised mass) exceeds 3,500 kg, this gap must be at least 50 m where the requirement applies. Your category C lorry falls within this requirement because of its MMA. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • The same minimum applies to vehicles and vehicle combinations with an overall length exceeding 10 m. The two criteria are alternatives: a short lorry with an MMA exceeding 3,500 kg does not also need to exceed 10 m to be covered; a long vehicle may be covered because of its length. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • With an 11 m lorry on a conventional road outside a built-up area, with one lane in each direction, overtaking permitted and traffic not congested, you must leave at least 50 m if you do not signal your intention to overtake. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • The exceptions in the next section apply only to the additional space intended to allow others to overtake you. You must still maintain the gap needed to avoid a collision; a traffic queue or a ban on overtaking does not allow you to drive close behind the vehicle ahead. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)

21Exceptions to the additional gap

A green truck follows an orange car with a safety gap on an urban street, both in the right-hand lane and travelling in the same direction.
The key idea

Know when the extra gap for overtaking does not apply.

CaseExtra gap to help overtaking
Inside a built-up areaNot required
Overtaking is prohibitedNot required
Several lanes in your directionNot required
Traffic is so heavy that overtaking is impossibleNot required

Remember

  • With very heavy traffic, check that overtaking really is impossible.
  • Count lanes in your direction, not across the whole road.

Exam trap: Wrong: many vehicles are enough for the exception. Right: traffic must make overtaking impossible.

Read the full explanation
  • In built-up areas, you are exempt from leaving the additional gap intended to allow others to overtake you. [RGC, art. 54.3.a](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • This additional obligation also does not apply where overtaking is prohibited or where there is more than one lane in your direction. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • You are also not required to leave the additional gap when traffic is so congested that overtaking is impossible. The exception depends on the manoeuvre being impossible because of that congestion, rather than simply on there being many vehicles. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On a conventional road with two lanes in your direction, the exception depends on the number of lanes available in that direction; two lanes in total, one in each direction, do not meet this condition. [RGC, art. 54.3.c](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)

22Tunnels: 150 metres or six seconds

A green heavy goods truck travels in the right-hand lane of a tunnel, leaving a large gap behind the orange car ahead.
The key idea

In tunnels, without intending to overtake, keep your lorry's special following distance.

150 mLorry minimum distance
Six secondsAlternative minimum interval
3,500 kgAuthorised mass threshold
Maximum authorised massMinimum without intending to overtake
Over 3,500 kg150 m or six seconds
Up to 3,500 kg100 m or four seconds

Remember

  • With your lorry over 3,500 kg MMA, keep 150 m or six seconds.
  • Increase the gap if you need more room to brake.
  • To measure time, choose a fixed point.
  • Count until your lorry’s front reaches the point the vehicle ahead passed.

Exam trap: Wrong: you choose 100 m for your heavy lorry. Right: without intending to overtake, keep 150 m or six seconds.

Read the full explanation
  • In tunnels and underpasses, if you do not intend to overtake, you must maintain at least 150 m or a minimum safety interval of six seconds behind the vehicle ahead when driving a lorry with an MMA exceeding 3,500 kg. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • The two minimums are alternatives. Increase the gap if a slippery road surface or reduced braking ability requires more space to avoid a rear-end collision. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95) [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • To check a time interval, you can choose a fixed point and count from when the vehicle ahead goes past it until the front of your lorry reaches it. At 90 km/h, six seconds is mathematically equivalent to 150 m; at a different speed, the equivalent distance changes, even though the interval remains six seconds. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • Vehicles with an MMA not exceeding 3,500 kg have a different minimum: 100 m or four seconds; your lorry belongs to the higher MMA group. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)

23Speed and traffic queues inside a tunnel

A truck with its hazard lights on is stopped inside an illuminated tunnel, leaving a large gap to the car ahead.
The key idea

In a tunnel, adjust your speed and follow signs and instructions.

Remember

  • Do not enter if the traffic light tells you to stop.
  • Tunnel lights do not remove your duty to stop within visible space.
  • Combine the lorry's limit, road type and signs.
  • If a queue stops you, see “Breakdown, fire and traffic queues in tunnels”.

Exam trap: Wrong: every tunnel has the same maximum speed. Right: consider the road, lorry, signs and conditions.

Read the full explanation
  • A tunnel does not have a single maximum speed simply because it is a tunnel. Take account of the road type, your lorry’s speed limit, specific signs, visibility and traffic conditions together. Artificial lighting does not remove your obligation to be able to stop within the distance you can see. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45) [RGC, art. 47](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a47) [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • Obey the traffic lights, variable message signs and instructions you receive in the tunnel. If the entrance traffic light prohibits entry, wait outside. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95) [RGC, art. 96](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a96)
  • If a traffic queue brings you to a stop in a tunnel or underpass, apply the measures in articles 97.3 and 115 explained in “Accidents, breakdowns and first aid”, in the section “Breakdown, fire and traffic queues in tunnels”. [RGC, art. 97.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a97) [RGC, art. 115](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a115)

24Lateral clearance and slowing down when passing

A truck overtakes a cyclist in the left lane, leaving ample lateral clearance on a road with separated carriageways.
The key idea

When passing other road users, leave side room and slow down when required.

20 km/hMinimum reduction stated
CaseWhat you must do
Overtake pedestrians, animals, animal-drawn vehicles, mopeds, personal mobility vehicles or cyclistsSee “Protecting cyclists and other vulnerable road users”
That overtake outside built-up areasAt least 20 km/h below the road limit
Pass an immobilised vehicleSee “Passing stationary vehicles and obstacles”

Remember

  • Match your speed to the space and the lorry's width.
  • When overtaking vulnerable road users, follow the required clearance and lane use rules.
  • See “Protecting cyclists and other vulnerable road users” for these conditions.
  • Outside built-up areas, slow down before and throughout this overtake.
  • Measure the reduction against the road's speed limit.
  • Also keep within any lower maximum for your lorry.

Exam trap: Wrong: you treat the reduction as permission to exceed the maximum. Right: slow down and obey the limits.

Read the full explanation
  • Keep sufficient lateral clearance when meeting or driving alongside other road users, adjusting your speed to the available space and your lorry’s width and projecting parts. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45) [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • Apply the lateral clearance and lane use requirements explained in “Manoeuvres with a lorry”, in the section “Protecting cyclists and other vulnerable road users”. [RGC, art. 85.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)
  • Outside built-up areas, before starting and throughout any overtaking manoeuvre involving pedestrians, animals, animal-drawn vehicles, mopeds, personal mobility vehicles or cyclists, you must reduce your speed to at least 20 km/h below the road’s speed limit, while also respecting any lower maximum speed for your lorry. For example, if the stretch of road has a limit of 80 km/h, your maximum speed throughout the overtaking manoeuvre is 60 km/h, even if your lorry is empty. [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)
  • To go past stationary vehicles, apply the conditions in article 88.1 explained in “Manoeuvres with a lorry”, in the section “Passing stationary vehicles and obstacles”. [RGC, art. 88.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a88)

Choose your lorry’s speed

Check the road, vehicle, restrictions and circumstances in that order.

  1. Identify whether you are driving outside a built-up area, on an urban road, on a stretch of road through a town, or on a motorway or dual carriageway within a built-up area.
  2. Apply the lorry’s maximum speed and check for dangerous goods or other specific restrictions.
  3. Check signs, temporary traffic rules and applicable minimum speeds.
  4. Assess visibility, grip, traffic, the load and your own condition.
  5. Reduce your speed as much as you need to stop safely, even below the minimum if there is a justified reason.

Identify the distance you are considering

Distinguish reaction distance from braking distance and add them together to find stopping distance.

  1. Identify the moment when you perceive the hazard.
  2. Measure the distance you travel before applying the brake: reaction distance.
  3. Measure the distance from applying the brake to coming to a standstill: braking distance.
  4. Add the two distances: stopping distance.
  5. Check that you have enough visible, clear space to stop.

Choose your following distance

Combine the basic safety gap with the minimum distances for each situation.

  1. Leave enough space to stop without hitting the vehicle ahead if it brakes suddenly.
  2. If you follow a cyclist in an urban area, apply the rule in «Following distance to avoid collisions».
  3. Outside tunnels, check whether you must leave room for others to overtake you and whether the 50 m minimum applies.
  4. Check the exceptions: built-up areas, overtaking prohibited, several lanes in your direction, or traffic so congested that overtaking is impossible.
  5. In a tunnel or underpass, if you do not intend to overtake, leave 150 m or six seconds with your lorry whose MMA (maximum authorised mass) exceeds 3,500 kg.
  6. Increase the gap if grip, visibility or braking capability requires it.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module