Theory · C+E Licence - Articulated Truck · Module 8 of 13

Speed and distances for vehicle combinations

You learn to choose a legal and appropriate speed for your combination on each road and calculate the space you need to stop. You apply safe following distances, the five-metre gap behind cyclists in urban areas, the 50-metre gap to facilitate overtaking and the specific separation distances in tunnels.

40 min read24 sectionsReviewed Nov 3, 2026
An articulated lorry follows an orange car with a large gap on a two-way rural road.
Safe following distance for articulated vehicles

1Legal maximum and appropriate speed

An articulated lorry with a green cab and orange semitrailer travels in its right-hand lane toward a bend that disappears into fog.
The key idea

Adjust your speed so you can stop your whole combination within the space you see.

Remember

  • Respect the maximum, but slow down further when necessary.
  • Adapt to your condition, load, vehicle, weather, road and traffic.
  • Keep your combination’s limits even when you carry no load.
  • Do not apply a fixed speed reduction for every load.

Exam trap: Wrong: Keeping below the maximum is always enough. Right: Slow down to stop before foreseeable hazards.

Read the full explanation
  • The maximum speed is a legal ceiling; the minimum prevents you from driving abnormally slowly without justification. An appropriate speed allows you to control and stop the combination when faced with a foreseeable hazard, even if this means driving well below the maximum. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You can drive at an inappropriate speed without exceeding the permitted limit. For example, 80 km/h on a conventional road may be excessive for your articulated vehicle in fog, on ice or on a sharp bend. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You must adapt your speed to your physical and mental condition, the condition and characteristics of the road, your vehicle, its load, the weather and traffic. Driving an unladen combination does not allow you to use the speed limits for a car. When it is laden, you must assess how it actually responds, without inventing a fixed speed reduction for every load. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You must be able to stop within the distance you can see and before any obstacle that may appear. If the clear distance you can see becomes shorter, slow down until your stopping distance fits within it. Knowing the route does not guarantee that the carriageway beyond a bend or the brow of a hill is still clear. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

2Autopistas and autovías outside built-up areas

An articulated truck with an orange tractor unit and a green semitrailer travels in the right lane of a divided motorway with a barrier separating the carriageways, amid dry hills and cypress trees.
The key idea

Outside built-up areas, your ordinary combination has the same maximum on autopistas and autovías.

90 km/hYour combination’s maximum
Road outside built-up areasOrdinary goods combination: maximum
Autopista90 km/h
Autovía90 km/h

Remember

  • Obey any lower limit that applies.
  • Apply the specific limits if you carry dangerous goods.
  • Apply the specific limits if you operate under special transport rules.
  • A higher speed sign does not raise your combination’s maximum.

Exam trap: Wrong: A higher speed sign lets you exceed 90 km/h. Right: Keep your combination’s maximum.

Read the full explanation
  • With an ordinary lorry and trailer or tractor unit and semi-trailer, your general maximum speed on autopistas (motorways) and autovías (dual carriageway motorways) outside built-up areas is 90 km/h. This applies both to articulated vehicles and to motor vehicles with trailers included in the table. You must observe any lower limit that applies to the road section or transport operation. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • The maximum of 90 km/h is the same on autopistas and autovías. If you carry dangerous goods or operate under special transport rules, you must apply the specific limits for those operations. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • Where a 70 km/h limit applies on an autovía, you must observe that maximum and slow down further if necessary. A sign showing a value above the maximum for your category does not, by itself, authorise you to exceed the combination’s 90 km/h limit. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

3Conventional roads and roads reserved for motor vehicles

A green articulated truck with an orange semitrailer travels behind a blue car in the right-hand lane of a conventional road in a Mediterranean landscape.
The key idea

On conventional roads, you must keep your ordinary combination’s maximum even when overtaking.

80 km/hYour combination’s maximum
Road outside built-up areasOrdinary goods combination: maximum
Conventional road80 km/h
Conventional road reserved for motor vehicles80 km/h

Remember

  • Obey any lower limits that apply.
  • A wide hard shoulder or extra lanes do not raise your maximum.
  • Physical separation between directions does not raise your maximum either.
  • A conventional road reserved for motor vehicles keeps the conventional road limit.

Exam trap: Wrong: Exceeding 80 km/h to finish overtaking. Right: Overtake within your applicable maximum.

Read the full explanation
  • Outside built-up areas, the general maximum speed for your ordinary combination on a conventional road is 80 km/h. You also apply this limit if the road has a wide arcén (hard shoulder), a good surface or several lanes in your direction. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • The option to set a 100 km/h limit on a conventional road with physical separation between opposing traffic flows applies to the categories expressly listed in article 48, which do not include your goods vehicle combination. Your maximum remains 80 km/h, unless a lower limit applies. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • A conventional road reserved for motor vehicles does not become an autopista or autovía simply because it is reserved for those vehicles. If you drive a lorry with a non-light trailer on it, without carrying dangerous goods or operating under special transport rules, your general maximum speed is 80 km/h. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • With your articulated vehicle, you cannot overtake a car maintaining 90 km/h on that road: it is already exceeding the maximum speed you are allowed to reach. Nor can you exceed 80 to overtake a lorry travelling at 80. The need to complete a manoeuvre quickly does not authorise you to exceed the speed limit. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

4Unsurfaced roads

An articulated truck with an orange cab and green semitrailer travels to the right along an unpaved road with gravel, ruts and potholes in a dry Mediterranean landscape.
The key idea

On unsurfaced roads, adjust to the surface and keep within the maximum.

30 km/hUnsurfaced road maximum

Remember

  • Check the surface, signs and whether your combination is allowed access.
  • Slow down further for potholes, dust, gravel, loads or slopes.
  • The name “track” does not tell you whether the road is surfaced.

Exam trap: Wrong: You always subtract ten for dangerous goods. Right: Do not automatically subtract this on unsurfaced roads; obey the restrictions that apply.

Read the full explanation
  • On an unsurfaced road, your maximum speed limit is 30 km/h. The limit applies because the road is unsurfaced, not simply because it is called a track. You must check the road surface and any specific signs, as well as whether your combination is allowed to use the road. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • Travelling at 30 km/h does not guarantee safe progress over potholes, ruts, dust or loose gravel. You may need to drive much more slowly to maintain grip and control of the whole combination. The load, gradient and space available to pass oncoming road users may require a further reduction. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • You must not automatically subtract ten from that 30 km/h limit because you are carrying dangerous goods: the interurban reduction in article 48.1.b applies to the speeds in the table in subsection a. You must combine the track’s maximum speed with the other restrictions that actually apply to the transport operation, without inventing a general 20 km/h rule. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

5Urban streets: 20, 30 and 50

An articulated truck facing right occupies the near side of a shared-level urban street, with pedestrians beside the building fronts.
The key idea

In towns, identify the street type and count only lanes for general traffic.

20 km/hShared surface
30 km/hOne lane each way
50 km/hSeveral lanes each way
Urban streetCombination allowed access: general maximum
Shared surface for carriageway and pavement20 km/h
One lane in each direction30 km/h
Two or more lanes in each direction50 km/h

Remember

  • Check that your combination is allowed on the street.
  • Do not count reserved lanes or lanes only for public transport.
  • Local signs can lower the limits.
  • Exceptionally, signs allow 50 km/h with one lane in each direction.
  • Slow down further if pedestrians or visibility require it.

Exam trap: Wrong: Counting a bus-only lane to raise your limit. Right: Count only general traffic lanes.

Read the full explanation
  • On an urban road where the carriageway and pavement form a single shared surface, the general maximum speed is 20 km/h. On an urban road with only one lane in each direction, it is 30 km/h. On an urban road with two or more lanes in each direction, it is 50 km/h. These limits also apply to your combination when it is authorised to use the street. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • When counting lanes, you must exclude those reserved for particular users and those exclusively for public transport. If your direction has one general traffic lane and one bus-only lane, you must not conclude that you have two general traffic lanes and a maximum speed of 50. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • The municipal authority may lower urban speed limits using specific signs. Exceptionally, it may raise the limit on a road with only one lane in each direction to a maximum of 50 km/h, also using specific signs. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • On a shared surface, among access points and with pedestrians nearby, even 20 km/h may be inappropriate. You must adjust your speed to the distance you can see and the space occupied by the whole combination. The general limit does not replace your duty to stop if circumstances require it. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)

6Travesías and motorways in built-up areas

An articulated lorry with an orange cab and green semitrailer travels to the right along a through-road between houses with tiled roofs.
The key idea

Within built-up areas, distinguish through roads from autopistas and autovías.

50 km/hGeneral through road maximum
80 km/hUrban autopista or autovía
90 km/hOrdinary combination’s raised ceiling
Road within built-up areasOrdinary goods combination: general maximum
Travesía: through road50 km/h
Autopista or autovía80 km/h

Remember

  • Adjust your speed before the road type changes.
  • Obey any lower limit that applies.
  • Raising an urban motorway limit needs agreement between authorities and specific signs.

Exam trap: Wrong: Automatically choosing 90 km/h on an urban autovía. Right: The general maximum is 80 km/h. Raising it requires agreement between municipal and road authorities, specific signs and your category’s ceiling.

Read the full explanation
  • On a travesía (the stretch of road through a town), your general maximum speed is 50 km/h, unless another applicable limit applies. The limit may be lowered by agreement between the municipal authority and the road authority, using specific signs. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • On autopistas and autovías within built-up areas, the general maximum speed is 80 km/h. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • The maximum speed on these autopistas and autovías may be increased by agreement between the municipal authority and the road authority, using specific signs, without exceeding the general maximum for your category outside built-up areas. For your ordinary combination, the corresponding ceiling is 90 km/h. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)
  • On a journey, you may move from a conventional road to a travesía and then to an urban street with one lane in each direction. Adjust your speed before entering each section according to the rules that apply to it. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50)

7Dangerous goods

An articulated truck with a tank semitrailer and a red diamond bearing a flame travels in the right-hand lane of a rural road.
The key idea

If you carry dangerous goods, apply the specific limits for each road type.

10 km/hReduction from interurban table
80 km/hAutopista or autovía outside towns
70 km/hConventional road
40 km/hThrough road or multilane street
RoadGoods combination carrying dangerous goods: maximum
Autopista or autovía outside built-up areas80 km/h
Conventional road outside built-up areas70 km/h
travesías (through-town stretches of an interurban road)40 km/h
Urban street: two or more lanes each way40 km/h
Urban street: one lane each way30 km/h
Urban shared surface20 km/h

Remember

  • Also obey lower signed limits and the conditions of your transport operation.
  • If special transport rules also apply, obey both sets of restrictions.

Exam trap: Wrong: Subtracting ten from every urban limit. Right: Apply the specific urban limits for dangerous goods.

Read the full explanation
  • If your combination carries dangerous goods, you must reduce the interurban maximum speeds in the table for your vehicle by 10 km/h. The resulting limits are 80 km/h on motorways and dual carriageways outside built-up areas and 70 km/h on conventional roads. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • You must also comply with any lower signed limit and the specific conditions of the transport operation. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • On urban roads with two or more lanes in each direction and on stretches of road through a town, the specific maximum for dangerous goods is 40 km/h. On a street with only one lane in each direction, you must observe the generic 30 km/h limit, and on a street with a single shared surface for pedestrians and vehicles, the limit is 20. The 40 km/h limit comes from article 50.4; the 30 and 20 km/h limits are the generic limits in article 50.1. Do not subtract ten from urban limits. [RGC, art. 50](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a50) [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • If your combination carries dangerous goods and also operates under special transport rules because of its mass or dimensions, you must comply with the restrictions of both regimes together. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

8Special transport and testing

An articulated truck carrying a secured cylindrical load travels along a rural road, leaving a large gap behind the car ahead in the same lane.
The key idea

For special transport and testing, you must follow your authorisation’s conditions.

70 km/hGeneral authorisation: maximum
60 km/hSpecific and exceptional: ceiling
50 mMinimum gap: listed special groups
150 mMinimum visibility ahead and behind
Special transport authorisationCombination under special transport rules: maximum
General70 km/h
Specific60 km/h
ExceptionalAuthorised speed, never above 60 km/h

Remember

  • Check your authorisation and Annex III.
  • Obey stricter restrictions on your ITV roadworthiness card.
  • In groups 1, 2 and 3, keep at least 50 m ahead.
  • For these groups, stop travelling if weather is dangerous or minimum visibility is missing.
  • Testing permission allows 30 km/h above general maximums only on the specified route.
  • Never use that permission on urban roads, through roads or sections with speed signs.

Exam trap: Wrong: Applying ordinary gap exceptions to special transport’s 50 m. Right: Keep the specific minimum for groups 1, 2 and 3.

Read the full explanation
  • If your combination operates under special transport rules, you must consult its authorisation and Annex III. For the group of vehicles operating under these rules, a general authorisation allows a maximum of 70 km/h and a specific authorisation 60 km/h; an exceptional authorisation sets the authorised speed, which cannot exceed 60 km/h. Any stricter restrictions on the ITV (vehicle roadworthiness test) card take precedence. [RGC, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii) [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • Under the common conditions in Annex III for groups 1, 2 and 3, you must keep at least 50 m behind the vehicle ahead. You must also stop travelling if weather conditions create a risk or if you do not have visibility of at least 150 m both ahead and behind. This is a specific regime: do not automatically apply the exceptions to the ordinary 50 m rule to it. [RGC, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#aniii) [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • A special testing permit allows you to exceed generic maximum speeds by up to 30 km/h only along the specified route. It does not allow you to do so on urban roads, on stretches of road through a town or on sections with specific speed signs. [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)

9Signs, restrictions and speed limiter

An articulated truck follows a passenger car in the right-hand lane of a road beside a sign prohibiting overtaking by trucks.
The key idea

You must obey every applicable limit even when your vehicle has a speed limiter.

90 km/hYour N3 tractor unit’s limiter
80 km/hYour combination on conventional roads
Your combination with an N3 tractor unitSpeed reference
Technical limiter setting90 km/h
Conventional road maximum80 km/h; slow further if necessary

Remember

  • Obey restrictions on the driver, vehicle, load and road section.
  • Obey temporary and variable signs too.
  • Keep control even when you have electronic driving aids.
  • Helping to tamper with the limiter is a very serious offence.
  • Check settings and exemptions in “Maximum dimensions and masses”.

Exam trap: Wrong: Your limiter allows 90 km/h on conventional roads. Right: Your combination’s maximum is 80 km/h; slow down further when necessary.

Read the full explanation
  • You must observe specific signed limits, including temporary and variable limits, and those imposed on you as the driver, on the vehicle or on its load. If several applicable restrictions coincide, you must comply with all of them together. A general speed sign does not remove a restriction specific to your combination. [RGC, art. 47](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a47) [RGC, art. 52](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a52)
  • The technical setting of the limiter and its exemptions are explained in «Maximum dimensions and masses», in the section «Speed limiter on the motor vehicle». When choosing your driving speed, you must distinguish this setting from the speed permitted on each road section. [RD 1417/2005, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a4)
  • Your N3 tractor unit has a limiter set to 90 km/h. On a conventional road, you must observe the 80 km/h limit for your combination and slow down further if rain, bends or visibility require it. [RD 1417/2005, art. 4](https://www.boe.es/buscar/act.php?id=BOE-A-2005-19990#a4) [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45) [RGC, art. 48](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a48)
  • You must remain in control of your speed even if the vehicle has electronic aids. The technical device does not decide whether you have enough space to stop or what speed is appropriate when entering a tunnel. [RGC, art. 52](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a52)
  • If you participate or assist in installing or activating components that interfere with the limiter, you commit a very serious offence. The device's characteristics and exemptions are covered in «Maximum dimensions and masses». [Traffic Act, art. 77.m](https://www.boe.es/buscar/act.php?id=BOE-A-2015-11722#a77)

10General minimum speeds for the combination

An articulated lorry with an orange cab and green semitrailer travels to the right in the right-hand lane of a divided motorway with two lanes in each direction, in a Mediterranean landscape.
The key idea

You must respect the general minimum unless you have a justified reason.

60 km/hAutopista and autovía minimum
40 km/hOrdinary conventional road minimum
Road: ordinary goods combination under general rulesGeneral minimum
Autopista or autovía60 km/h
Conventional road, including one reserved for motor vehicles40 km/h
Unsurfaced road15 km/h
Urban road: maximum 20 km/h10 km/h
Urban road: maximum 30 km/h15 km/h
Urban road: maximum 50 km/h, or ordinary travesía25 km/h

Remember

  • Except on autopistas and autovías, halve the general maximum for your category and road.
  • Do not automatically calculate the minimum from a signed maximum.
  • Also obey any signed minimum.
  • Even without traffic, you need justification to drive below the minimum.
  • Never maintain a minimum speed when doing so is dangerous.

Exam trap: Wrong: Your autovía minimum is 45 km/h. Right: The general minimum is 60 km/h, unless you have a justified reason.

Read the full explanation
  • On motorways and dual carriageways, the general minimum speed for motor vehicles is 60 km/h, including for your ordinary combination. This minimum has its own figure for these roads and allows the justified exceptions provided for in the regulations. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • On other roads, the general minimum is half the generic speed limit for your vehicle category on that road. With your ordinary combination on a conventional road, the pair is a maximum of 80 and a minimum of 40 km/h. On a road reserved for motor vehicles that is a conventional road, you must apply the same reference, rather than the motorway minimum. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • On an unsurfaced road with a generic maximum of 30 km/h, half is 15 km/h. For urban roads under the ordinary generic rules, the pairs are 20/10, 30/15 and 50/25 km/h. On an ordinary stretch of road through a town with a generic maximum of 50, the minimum reference is 25. These minimum speeds do not require you to drive dangerously. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • You must not calculate the minimum by automatically dividing any specific signed maximum by two. Article 49 uses the generic limit for your vehicle category and the road as its basis; you must also observe a signed minimum where one exists. The prohibition on driving below the minimum without justification applies even when there are no other vehicles on the road. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)

11When you can drive below the minimum

An articulated lorry travels behind two cars in its right-hand lane, with both rear hazard lights illuminated and the shoulder clear.
The key idea

You may drive below the minimum when circumstances prevent you from safely maintaining it.

3,500 kgMaximum authorised mass threshold
Vehicle travelling abnormally slowly because of an emergency, seriously disrupting trafficHard shoulder use
Maximum authorised mass not exceeding 3,500 kgYou must use it if passable and wide enough
Combination with maximum authorised mass exceeding 3,500 kgStay on the carriageway; shoulder only for emergencies

Remember

  • Adjust your speed for queues, ice, poor visibility or breakdowns.
  • Special vehicles, special transport and escort duties also have specific legal provisions.
  • Use hazard lights if you cannot reach the minimum and risk being hit behind.
  • With your heavy combination, stay on the carriageway; use the shoulder only for emergencies.

Exam trap: Wrong: Maintaining the minimum even on dangerous ice. Right: Slow down when traffic, your vehicle or the road prevents you from safely maintaining it.

Read the full explanation
  • You may drive below the minimum when traffic, your vehicle or the road prevents you from maintaining a higher speed safely. A queue, ice, insufficient visibility or a breakdown may justify this. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • The regulations also provide for special vehicles, special transport operations and cases involving protection or escort duties, where you adapt your speed to that of the vehicle you accompany. The justification comes from the circumstances or the service provided under the regulations. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • If you cannot reach the required minimum and there is a risk of a rear-end collision, you must switch on your hazard warning lights while driving. With your combination with an MMA (maximum authorised mass) over 3,500 kg, you must remain on the carriageway; use of the arcén (hard shoulder) is reserved for emergencies. The obligation to use a hard shoulder that is passable and wide enough when an emergency causes you to drive at an abnormally low speed that seriously disrupts traffic applies to vehicles with an MMA not exceeding 3,500 kg. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49) [RGC, art. 31](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a31) [RGC, art. 36](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a36)
  • The actions you take in a breakdown and when immobilised in an emergency are covered in «Responding to accidents and breakdowns». [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)

12People, animals and nearby access points

An articulated lorry with a green cab and an orange semitrailer is stopped before a zebra crossing where a woman and a child are crossing hand in hand.
The key idea

Slow down before approaching people, animals or places where they may appear.

Remember

  • Prepare to stop if pedestrians are present or may enter your path.
  • Take extra care around children, older people, blind people and people with reduced mobility.
  • Slow near cyclists, cycle routes and pedestrian crossings without traffic lights or officer control.
  • Slow near schools, markets, animals and buildings opening directly onto the road.
  • Slow down when approaching stopped buses, especially school buses.
  • Outside built-up areas, slow near vehicles stopped on the carriageway, roadside assistance and cyclists.

Exam trap: Wrong: Slowing down only when someone is already in your path. Right: Also slow down when you can foresee them entering it.

Read the full explanation
  • You must slow down and, if necessary, stop when pedestrians are on the part of the road you use or you can reasonably expect them to enter it. Pay particular attention to children, older people, blind people and people with reduced mobility. From the cab, you may have a good view into the distance while nearby areas are difficult to see. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • You must slow down as you approach cycles, roads reserved exclusively for cycles, their junctions and pedestrian crossings without traffic lights or an officer controlling traffic. You must also slow down near markets, educational establishments and places where you can expect children. You must prepare to react before anyone enters the path of the towing or towed vehicle. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • You must drive at a moderate speed when animals are present or you can anticipate them entering the road, and on sections where buildings have direct access to the part of the road you use. An access point hidden by a vehicle or structure requires you to anticipate hazards. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • As you approach a stopped bus, especially a school bus, you must slow down. Outside built-up areas, you must also do so when approaching vehicles immobilised on the carriageway, roadside assistance services and cycles on the carriageway or hard shoulder. Stay alert for people who may be hidden from view and avoid letting the size of your combination reduce safety margins. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)

13Junctions, narrow sections and visibility

A green articulated truck with an orange semitrailer approaches a bend in the right lane, with visibility obstructed by a rocky hillside and the driver seated on the left side of the cab.
The key idea

Slow near junctions and poor visibility until you can pass or stop safely.

50 km/hSigned junction: virtually no visibility

Remember

  • Slow near level crossings, roundabouts, narrow sections and junctions where you lack priority.
  • Stop if you cannot continue safely.
  • Slow when passing oncoming traffic if space or conditions require it.
  • Allow for your trailer’s space too.
  • If dazzled, slow down and stop if necessary.

Exam trap: Wrong: Driving at 50 km/h through a signed junction with virtually no visibility. Right: This is a maximum; obey lower limits and slow further if you need to stop.

Read the full explanation
  • You must slow down when approaching level crossings, roundabouts and junctions where you do not have priority, and at narrow sections or where visibility is reduced. This duty may require you to stop. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • If a junction is properly signposted and visibility of the road is virtually non-existent, you must not exceed 50 km/h. This figure is a specific maximum, not a recommended speed for passing through. If another limit is lower or you need to drive more slowly to be able to stop, you must comply with that stricter requirement. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • When passing an oncoming vehicle, you must slow down if the available space, the characteristics of the vehicles or the weather prevent you from doing so safely. With a long combination, a tight bend may leave little lateral clearance. You must also allow for the space needed by the towed vehicle and stop if you cannot continue safely. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)
  • If you are dazzled, you must slow down and even stop if necessary. In dense fog, heavy rain, snow, dust or smoke, you must adjust your speed to what you can actually see. Having priority or your lights on does not allow you to travel beyond the distance within which you can maintain control and stop. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46)

14Rain, wind, bends and descents

An articulated truck travels in the rain on a wet road and maintains a wide gap behind the car ahead.
The key idea

Adjust your speed before facing rain, wind, bends and descents.

Remember

  • In rain or on slippery roads, slow down and increase your following distance.
  • Slow where you could spray water or gravel onto people.
  • In wind, slow down early and steer smoothly.
  • Choose your speed for a bend before entering it.
  • Consider your load, the surface and what you can see.
  • Downhill, follow manufacturer guidance on gears and braking aids to avoid overloading your brakes.

Exam trap: Wrong: Waiting until you lose stability to slow down. Right: Adjust your speed beforehand for wind, bends and your load.

Read the full explanation
  • In rain or on a slippery road surface, you must slow down and increase your distance from the vehicle ahead. You must also slow down wherever you may spray water, gravel or other material onto other road users. The problem is not just losing grip: the movement of your combination can harm those nearby. [RGC, art. 46](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a46) [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You must adapt your speed to the wind and gusts, especially with a tall or long combination. Anticipate changes in exposure when leaving a tunnel or a sheltered area. Slow down in advance and use smooth control inputs; you do not need to wait until you notice a significant deviation to correct your course. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • You must choose your speed for a bend before entering it, taking account of visibility, the radius of the bend, the road surface and the load. A high centre of gravity and a poorly distributed load can impair stability. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)
  • On a long descent, you must maintain a controllable speed and a margin for braking. As technical guidance, select a suitable gear and use the available engine braking and retardation in accordance with the manufacturer's instructions to avoid overloading the service brake. Detailed operation of retarders and trailer brakes is covered in «Trailer and vehicle combination braking». [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45)

15Slowing down without causing rear-end collisions

An articulated lorry travels in the right lane with its brake lights illuminated, with space before a queue of cars ahead and an orange car behind.
The key idea

Before braking heavily, check behind and warn other drivers whenever you can.

Remember

  • Check your mirrors while keeping your attention ahead.
  • When you see a queue, begin slowing down early.
  • Avoid sudden braking that could cause a collision behind you.
  • Warn with repeated brake lights or the prescribed arm signal.
  • For immediate danger, act without waiting to finish warning others.

Exam trap: Wrong: The following driver’s safe gap removes your duty to warn. Right: Except in immediate danger, check and warn before slowing down significantly.

Read the full explanation
  • Except in imminent danger, before slowing down considerably you must check that you can do so without putting other drivers at risk and give advance warning. You must avoid slowing down abruptly in a way that could cause a rear-end collision. The following driver's duty to keep a safe distance does not remove your duty to anticipate. [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)
  • You must check the traffic behind you in your mirrors when preparing to slow down significantly, while maintaining your attention ahead. When you see a queue, start adjusting your speed with room to spare instead of waiting until you reach its tail. The length and response of your combination make this anticipation especially valuable. [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)
  • Whenever possible, you must warn of your intention to stop or brake considerably by repeatedly operating the brake lights or using the prescribed arm signal. Article 109 also regulates the use of hazard warning lights when you are immobilised on an autopista (motorway), an autovía (dual carriageway) or in significantly reduced visibility. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109) [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)
  • If an imminent danger arises, you must act to avoid it: the exception allows the necessary response without waiting to complete an advance warning. Your aim is to preserve space ahead and make your slowing down predictable for those behind you. [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)

16Speed when passing vulnerable road users

An articulated truck overtakes a cyclist in the left lane of a divided road with two lanes in each direction, leaving ample lateral clearance in a rural setting.
The key idea

When overtaking vulnerable road users, you must slow down and leave space beside them.

20 km/hMinimum reduction below road limit
1.5 mMinimum sideways gap
CaseMinimum reduction below road limitMinimum sideways gap
Overtaking vulnerable road users outside built-up areas20 km/h before and throughout1.5 m
Passing legally specified stopped vehicles occupying all or part of your lane20 km/h1.5 m

Remember

  • Take extra care near pedestrians, animals, cyclists, mopeds and personal mobility vehicles.
  • Outside built-up areas, reduce speed before overtaking and throughout the manoeuvre.
  • Also respect your combination’s maximum; slow down further when necessary.
  • Use part or all of the adjacent lane or oncoming lane.
  • With several lanes in each direction, change lanes completely.

Exam trap: Wrong: Applying the stopped-vehicle rule to every traffic queue. Right: It covers breakdowns, accidents and specified services occupying your lane; meet both the speed reduction and sideways gap requirements.

Read the full explanation
  • When overtaking pedestrians, animals, animal-drawn vehicles, mopeds, personal mobility vehicles, cyclists or groups of cyclists, you must take extra care. Outside built-up areas, you must travel at least 20 km/h below the road's speed limit before starting and throughout the manoeuvre. [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)
  • You must combine this reduction with the maximum speed applicable to your combination and a speed appropriate to the circumstances. If the road has a 70 km/h limit, the maximum resulting from the reduction is 50 km/h. If safety requires a lower speed, you must slow down further; subtracting this amount does not automatically make the manoeuvre safe. [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)
  • You must leave at least 1.5 m of lateral clearance and use part or all of the adjacent lane or the lane for oncoming traffic; where there is more than one lane in each direction, you must change lanes completely. Lateral clearance and reduced speed are simultaneous requirements, not alternatives you can choose between. [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)
  • When passing a vehicle stopped for one of the reasons listed in article 88 and occupying all or part of your lane, you must leave at least 1.5 m of lateral clearance, using the opposite lane if needed, and travel at least 20 km/h below the road's speed limit. This includes breakdowns, accidents and the emergency, assistance and maintenance services specified there; it is not a rule for passing a queue stopped by traffic. [RGC, art. 88](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a88) [RGC, art. 85](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a85)

17Reaction, braking and stopping the combination

An articulated truck travels in the right-hand lane toward a fallen branch, with consecutive green and orange strips representing reaction and braking distances and ending before the obstacle.
The key idea

To stop, you need both reaction distance and braking distance.

25 mEach second at 90 km/h
22.2 mApproximately each second: 80 km/h
DistanceSpace you must count
ReactionFrom noticing danger until you start braking
BrakingFrom applying the brake until you stop
StoppingReaction distance plus braking distance

Remember

  • During your reaction, you travel before you start braking.
  • During braking, you travel until you stop.
  • With unchanged reaction time, doubling speed doubles your reaction distance.
  • In comparable conditions, doubling speed makes braking distance about four times greater.
  • Allow more space if grip, visibility or your reaction worsens.
  • Consider your load, tyres, brakes and the slope too.

Exam trap: Wrong: Counting stopping distance only from pressing the brake. Right: Include your reaction distance too; example calculations are not fixed distances for your combination.

Read the full explanation
  • Between perceiving a danger and starting to brake, you travel the reaction distance. From the moment you apply the brake until you come to a standstill, you travel the braking distance. To obtain the stopping distance, you must add the two together. [DGT, Road Safety Manual 2026](https://sede.dgt.gob.es/export/sites/dgt/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2026/MANUAL-II-Cuestiones-de-Seguridad-Vial.pdf)
  • With the same reaction time, doubling your speed means you travel twice as many metres before braking. With all other conditions equal and comparable deceleration, your braking distance increases approximately with the square of your speed: doubling your speed makes it approximately four times the original distance. [DGT, Road Safety Manual 2026](https://sede.dgt.gob.es/export/sites/dgt/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2026/MANUAL-II-Cuestiones-de-Seguridad-Vial.pdf)
  • At 90 km/h you travel 25 m per second, and at 80 km/h approximately 22.2 m. If, in an exercise, you assume one second of reaction time and 40 m of braking distance at 90 km/h, you need 65 m to stop; this is a hypothetical calculation, not a fixed distance for your combination. [DGT, Road Safety Manual 2026](https://sede.dgt.gob.es/export/sites/dgt/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2026/MANUAL-II-Cuestiones-de-Seguridad-Vial.pdf)
  • You must increase your safety margin if grip, visibility or your ability to react deteriorates. The mass and distribution of the load, the tyres, the brakes and the gradient also affect your stopping distance. Brake operation, loss of braking effectiveness on descents and preventing jackknifing are covered in «Trailer and vehicle combination braking». [DGT, Road Safety Manual 2026](https://sede.dgt.gob.es/export/sites/dgt/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2026/MANUAL-II-Cuestiones-de-Seguridad-Vial.pdf)

18Safe following distance to prevent rear-end collisions

An articulated lorry maintains a wide gap behind a passenger car travelling ahead in the same lane on a wet road.
The key idea

Leave enough space to stop without colliding if the vehicle ahead brakes suddenly.

five metresMinimum behind urban cyclist

Remember

  • Increase your gap with higher speed, poorer grip or less visibility.
  • No single distance suits every situation.
  • If someone enters your gap, gradually restore it.
  • Do not cause dangerous braking while restoring your gap.
  • In urban areas, leave five metres behind a cyclist in your lane.
  • Increase that minimum if you need more space to avoid a collision.

Exam trap: Wrong: Five metres always suffices behind a cyclist. Right: It is the urban minimum when the cyclist is ahead in your lane; leave more if necessary.

Read the full explanation
  • Whenever you follow another vehicle, you must leave enough space to stop without colliding if it brakes suddenly. You must pay particular attention to speed, grip and braking ability. Apart from situations with specific minimum distances, article 54 does not set a single distance in metres that applies to every situation. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • You must increase your safety margin as your speed rises, grip deteriorates or visibility decreases. Spray from the vehicle ahead can make it harder for you to spot a queue. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • If another vehicle moves into the gap you have left, you must gradually restore sufficient separation without causing dangerous braking for those following you. Your duty to avoid a rear-end collision remains even if someone else's manoeuvre reduces the gap. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • In an urban area, if a cyclist is ahead of you in the same lane, you must leave a gap of at least five metres. Increase this distance if you need more space to avoid a rear-end collision. [RGC, art. 153.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a1-6) [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)

19The 50-metre gap to facilitate overtaking

An articulated truck travels in its lane on a two-way road, leaving a large gap behind the car ahead, with another car following the truck.
The key idea

With your heavy combination, also leave space for others to overtake when required.

50 mMinimum gap to help overtaking
3,500 kgRule applies above this MMA
10 mRule applies above this length
Vehicle or combination criterionWhen this criterion qualifies
Maximum authorised mass (MMA)Exceeding 3,500 kg
Total lengthExceeding 10 m

Remember

  • Exceeding either the maximum authorised mass threshold or total length threshold is enough.
  • Use maximum authorised mass, not the weight of your goods.
  • Your heavy combination qualifies even when empty.
  • Where the ordinary rule applies, keep this minimum unless you signal intention to overtake.
  • Leave more space when safety requires it.
  • Do not automatically add this minimum to an already sufficient gap.

Exam trap: Wrong: Always leaving exactly 50 m. Right: Unless signalling intention to overtake, leave at least 50 m outside built-up areas, with one lane each way, overtaking permitted and traffic allowing it. Leave more if necessary.

Read the full explanation
  • In addition to the gap you need to avoid a collision, if you follow another vehicle without signalling your intention to overtake, you must leave enough space for drivers behind you to overtake you safely. For vehicles with an MMA (maximum authorised mass) over 3,500 kg and vehicles or combinations with a total length over 10 m, this gap is at least 50 m. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • Meeting either criterion is enough: an MMA over 3,500 kg or a total length over 10 m. You must use the MMA, not the payload or the weight of the goods on that journey. Your ordinary C+E combination comes under this rule because of its heavy vehicle category, even when empty. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On a road outside built-up areas with one lane in each direction, where overtaking is permitted and traffic allows it, you must maintain this minimum gap if you do not signal an intention to overtake. With an 11 m combination, its length alone is enough to identify that the rule applies. The space allows another driver to pass you and move back in safely ahead of you. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • The 50 m is a minimum for this gap, not a distance that is sufficient in every situation. If your speed, rain or braking capability means you need 70 m to avoid a rear-end collision, you must leave at least that greater gap. You must not mechanically add 50 m to a distance that is already sufficient: you must meet both requirements at the same time. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)

20Exceptions to the ordinary 50-metre rule

An articulated lorry travels behind a car with a visible gap in the right-hand lane of a motorway with multiple lanes in each direction and a central barrier.
The key idea

Exceptions to the overtaking gap never remove your duty to prevent a collision.

CaseOrdinary additional 50 m gap for qualifying heavy or long vehicles
Within built-up areasNot required
Overtaking prohibitedNot required
More than one lane in your directionNot required
Traffic so congested that overtaking is impossibleNot required

Remember

  • You need no extra overtaking gap in built-up areas or where overtaking is prohibited.
  • Nor with several lanes your way, or traffic preventing overtaking.
  • Always keep enough space to avoid a collision.
  • Signalling intention to overtake does not remove your safe following distance.
  • Do not apply these exceptions to tunnels or special transport.

Exam trap: Wrong: Following closely where overtaking is prohibited. Right: Keep enough distance to avoid a collision and obey any specific minimum.

Read the full explanation
  • You do not have to leave the additional gap to facilitate overtaking in built-up areas, where overtaking is prohibited, where there is more than one lane in your direction, or when traffic is too congested to allow overtaking. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On a motorway with two lanes in your direction, you do not automatically have to leave a minimum of 50 m simply because you drive a long combination. You must keep enough space to stop without a collision. The road's maximum speed or traffic occupying the right-hand lane does not remove this basic obligation. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • On a road where overtaking is prohibited, outside a tunnel and with no other specific minimum, you must leave the distance you need to avoid a rear-end collision. If conditions require a greater distance, you must leave more despite the exception. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)
  • Signalling your intention to overtake does not remove the gap you need to avoid a collision either. Also, the exceptions in article 54.3 do not apply to the specific minimum gaps in tunnels or the separation required for special transport. [RGC, art. 54](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54)

21Tunnels and underpasses: 150 metres or six seconds

An articulated lorry travels through a long tunnel, leaving a wide gap behind the car ahead in the same lane.
The key idea

In tunnels, your heavy combination needs a larger gap when you do not intend to overtake.

150 mYour heavy combination’s minimum
six secondsAlternative interval for your combination
Moving vehicle with no intention to overtakeMinimum tunnel or underpass distanceAlternative minimum interval
Maximum authorised mass exceeding 3,500 kg150 msix seconds
Other vehicles100 mfour seconds

Remember

  • Apply this rule in underpasses too.
  • Also meet safety needs and obey signs.
  • Do not reduce the gap because overtaking is prohibited or there are several lanes.
  • Count from their rear passing a fixed point until your front reaches it.
  • If overtaking legally, keep enough space to avoid a collision.

Exam trap: Wrong: Choosing 100 m or four seconds for your heavy combination. Right: Without intending to overtake, keep at least 150 m or six seconds, and more if safety requires.

Read the full explanation
  • With your vehicle with an MMA over 3,500 kg, when you do not intend to overtake, you must maintain at least 150 m or a minimum time gap of six seconds behind the vehicle ahead in tunnels or underpasses. The general reference of 100 m or four seconds applies to other vehicles; you must not choose it for your heavy combination. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • You must maintain this separation while driving, as well as any gap required for safety and by signs. The regulations give metres or a time interval as alternative references. You must not treat the figure as a maximum or reduce a necessary gap simply because you have reached the minimum in the article. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • To check the time gap, choose a fixed point: count from when the rear of the vehicle ahead passes it until the front of your vehicle reaches it. If you use the time reference for your combination, you must allow at least six seconds. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • The exception in article 54.3.b for places where overtaking is prohibited concerns the gap intended to facilitate overtaking; the specific tunnel minimum remains compulsory. It also applies where there are several lanes in your direction when you do not intend to overtake. If you carry out a permitted overtaking manoeuvre, you must maintain the gap you need to avoid a collision. [RGC, art. 54.3.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a54) [RGC, art. 95.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)

22Adapting your speed to a tunnel

An articulated truck with a green cab and an orange semitrailer is stopped at a red traffic light at a tunnel entrance.
The key idea

Before entering a tunnel, adjust your speed and obey its signs.

Section and lanes in your directionOvertaking with your combination
Tunnel: only one lane in your directionProhibited
Underpass: only one lane in your directionProhibited
Section marked with sign S-5: only one lane in your directionProhibited
Two-way tunnel: more than one lane in your directionPermitted without entering the opposite direction

Remember

  • Follow the road limit, your combination’s limit and the signs.
  • Slow down beforehand if lighting, traffic or visibility requires it.
  • Do not enter when the traffic light prohibits it.
  • Obey message signs and instructions over loudspeakers.
  • Use the appropriate lights during daylight too.
  • In two-way tunnels, never enter the opposite direction to overtake.

Exam trap: Wrong: Every tunnel has the same maximum speed. Right: Apply the road limit, your combination’s limit and signs; slow further if necessary.

Read the full explanation
  • These articles do not set a single maximum speed that replaces all limits when you enter any tunnel. You must take account of the road type, your combination's maximum speed and the tunnel signs together. Slow down in advance if lighting, traffic or visibility makes it inappropriate to maintain your speed from outside the tunnel. [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • You must obey traffic lights, variable message signs and instructions over loudspeakers or by other means. You must not enter if the traffic light at the entrance prohibits entry; the regulatory exception for emergency, assistance and maintenance teams does not authorise your ordinary transport operation to enter. [RGC, art. 96](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a96) [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • You must use the appropriate lights in tunnels and underpasses at any time of day. If visibility changes as you enter, adapt your speed to maintain control within the distance you can see. For details of lighting devices, see «Safety devices for the vehicle combination». [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98) [RGC, art. 95](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)
  • In tunnels, underpasses and stretches marked with sign S-5, you must not overtake if there is only one lane in your direction. [RGC, art. 87.1.d](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a87) In a two-way tunnel with more than one lane in your direction, you may overtake, but you must not enter the opposite direction. [RGC, art. 95.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a95)

23Traffic queues inside a tunnel

An articulated truck remains stopped inside a tunnel with its hazard lights on, the driver on the left side of the cab, and a wide gap to the car ahead.
The key idea

If you see a queue inside a tunnel, slow down gradually and keep space ahead.

Remember

  • Slow down gradually when you see a queue.
  • Avoid waiting until the last moment to slow down.
  • See “Responding to accidents and breakdowns”, section “Fire and traffic queues in tunnels”.

Exam trap: Wrong: Waiting until the last moment to slow down. Right: Slow down gradually and keep space when you see a queue inside a tunnel.

Read the full explanation
  • If you see a traffic queue inside the tunnel, you must slow down progressively and avoid leaving it until the last moment as the gap closes. [RGC, art. 45](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a45) [RGC, art. 53](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a53)
  • If you are immobilised by traffic, a breakdown or a fire, you can find the procedure in «Responding to accidents and breakdowns», in the section «Fire and traffic queues in tunnels». [RGC, art. 97.3](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a97)

24Lanes with special limits

An articulated truck with dipped headlights on travels in a temporary lane separated by cones from opposing traffic, beside a carriageway undergoing roadworks.
The key idea

Check whether you may use the lane, and obey its speed and lighting rules.

60 km/hMinimum unless lower limits apply
80 km/hMaximum unless lower limits apply
Case: your C+E combinationSpeed limits
Contraflow lane opened to improve traffic flowYou cannot use it
Roadworks contraflow lane, if authorised on the road and not expressly prohibited60 to 80 km/h, unless lower limits are established or signed
Normal-direction lane beside contraflow: only lane in your direction60 to 80 km/h, unless lower limits are established or signed
Normal-direction lanes beside contraflow: several lanes in your directionOrdinary limits for the road and your combination
Hard shoulders and temporary additional lane (carril adicional circunstancial), with no other restriction60 to 80 km/h, unless lower limits are established or signed; dipped headlights always

Remember

  • Do not use a contraflow lane opened to improve traffic flow.
  • For roadworks, use it only if authorised on that road and not expressly prohibited.
  • In a roadworks contraflow lane, stay within it even when overtaking.
  • Obey lane markers and keep dipped headlights on by day and night.
  • Also use dipped headlights in the normal-direction lane beside the contraflow lane.
  • Temporary additional lane (carril adicional circunstancial): use only when no other restriction applies.

Exam trap: Wrong: You can use any contraflow lane. Right: With your C+E combination, only for roadworks, if authorised to use the road and not expressly prohibited.

Read the full explanation
  • With your C+E combination, you must not use a lane opened in the opposite direction to its normal traffic flow to ease congestion. If it is opened because of roadworks, you may use it when you are authorised to drive on that road and there is no express prohibition. [RGC, art. 41](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41)
  • In the lane opened because of roadworks, you must drive between 60 and 80 km/h, unless lower limits are established or signposted, with your dipped beam headlights on by day and night. You must stay within the lane, even when overtaking, and follow the cones and other delineators. [RGC, art. 41](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41)
  • If you drive in the normal-direction lane next to the lane opened in the opposite direction, you must keep your dipped beam headlights on and respect the separation between the lanes. With only one lane in your direction, the 60 to 80 km/h range applies, unless lower limits are established or signposted; with several lanes, the ordinary limits for the road and your combination apply. [RGC, art. 41](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41)
  • A temporary additional lane uses the arcenes (hard shoulders) to provide two lanes in one direction and one in the opposite direction. You may drive your combination there if no other restriction applies: when you drive on the hard shoulders or in the additional lane, you must drive between 60 and 80 km/h, unless lower limits are established or signposted, with your dipped beam headlights on by day and night. [RGC, art. 42](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a42)

Choosing your combination’s speed

Consider the road, vehicle, transport operation and actual conditions together.

  1. Identify whether you are outside a built-up area, on an urban road, on a stretch of road through a town or on an autopista (motorway) or autovía (dual carriageway) within a built-up area.
  2. Apply the maximum for your combination: 90/80 outside built-up areas; 30 on unsurfaced roads; 20/30/50 on streets, depending on their layout; 50 on a stretch of road through a town and 80 on an autopista or autovía within a built-up area.
  3. Check the rules for dangerous goods and special transport, restrictions specific to your combination and road signs.
  4. Check the minimum speed and whether you have a justified reason to drive below it.
  5. Slow down as much as necessary to stop within the distance you can see and keep your combination under control.

Choosing your following distance

Maintain a safe following distance and comply with the applicable minimum gaps.

  1. Assess the distance you need to avoid a collision if the vehicle ahead brakes suddenly.
  2. In urban areas, leave at least five metres if a cyclist is ahead of you in the same lane.
  3. If you do not signal your intention to overtake, check the ordinary 50 m rule for an MMA (maximum authorised mass) exceeding 3,500 kg or a total length exceeding 10 m.
  4. Check its exceptions: built-up areas, places where overtaking is prohibited, more than one lane per direction or traffic congestion that prevents overtaking.
  5. In a tunnel or underpass, if you do not intend to overtake, maintain 150 m or six seconds with your heavy combination.
  6. Check signs and specific rules, and leave a greater margin whenever safety requires it.

Anticipating a traffic queue

Slow down while maintaining your gap ahead and avoiding surprises for traffic behind.

  1. Spot the queue and check traffic behind while keeping your attention on the road ahead.
  2. Warn others of a significant reduction in speed whenever possible and slow down progressively.
  3. Keep enough distance to stop the whole combination.
  4. If the queue brings you to a standstill in a tunnel, follow the procedure in «Responding to accidents and breakdowns», section «Fire and traffic queues in tunnels».

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module