Theory · C Licence - Truck · Module 11 of 18

Load stowage and safety

You learn to position, distribute and secure goods on your lorry and check their safety during the journey and deliveries. You can answer category C questions on lashings, stability, tankers, loading and unloading, projecting loads and V-20 markings without confusing a correctly marked load with one that is authorised and properly secured.

32 min read26 sectionsReviewed Nov 3, 2026
A person checks the straps securing three crates on the bed of a rigid truck parked beside a road.
Load distributed, secured and checked

1What you must achieve with your load

A flatbed truck travels on the right with wooden crates distributed in a low layer and secured with straps, with its rear lights and licence plate unobstructed.
The key idea

Position and secure your load to prevent movement and danger.

Remember

  • Prevent your load from falling, dragging or moving dangerously.
  • Secure tarpaulins, packaging and tools in your cab too.
  • Keep lights, signs and plates visible.
  • Keep your view clear, your movement free and controls within reach.
  • Check weight distribution and the strength of supports.

Exam trap: Wrong: if everything fits, you can leave. Right: check weight distribution and securing too.

Read the full explanation
  • You must prevent the goods and their accessories from dragging, falling or moving dangerously, compromising stability, causing avoidable nuisance or obscuring lights, signs, plates or hand signals. This obligation includes packaging, tarpaulins and protective materials, even if the main load stays in place. [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • When positioning, stowing and securing the load, you decide where each item rests, how you distribute it among the others and what prevents it from moving. The fact that all the goods fit inside the load body does not prove that transport is safe; you must also assess mass distribution and the strength of the supports.
  • Before driving, you must know how the load is stowed and what restrictions it places on the vehicle. Mass concentrated high up or on one side changes how the lorry responds on a bend, even if you have not exceeded the authorised mass. Understanding the stowage helps you retain control and anticipate manoeuvres.
  • You must maintain your field of vision, freedom of movement and access to the controls. Also secure the tools and objects you carry in the cab: during braking, they can move and interfere with your driving. [RGC, art. 18](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a18).

2A low, centred centre of gravity

A truck travels in the right-hand lane of a rural road with metal blocks distributed across both sides of its bed in a single low layer and secured with orange straps.
The key idea

Put the heaviest goods low down and balance weight between both sides.

Remember

  • Avoid unnecessary stacking.
  • Move weight concentrated on one side before setting off.
  • Check the supporting base of tall items.
  • Keep each item in its permitted transport position.

Exam trap: Wrong: preventing sliding prevents overturning. Right: check whether the item can tip over too.

Read the full explanation
  • You must understand the centre of gravity as the point at which the weight of the whole vehicle and load is considered to be concentrated. Its position depends on the lorry and the entire load, including packaging and equipment. You do not necessarily have to place it at the geometric centre of the load body: you must achieve a distribution compatible with the axles and intended supports.
  • As a stowage principle, place the heaviest items at the bottom and avoid unnecessary stacking. Raising a substantial mass increases the tendency to overturn on bends or when changing direction. A bulky load can have little mass, while a small metal block can greatly alter the balance.
  • You must aim for balanced distribution on both sides of the longitudinal axis. If you concentrate heavy items on one side, you load the wheels and suspension unevenly and reduce the stability margin on that side.
  • For a tall item, assess both its supporting base and the height of its centre of gravity. A wide base and a low transport position improve its stability, provided you keep the item in its authorised orientation. Blocking that prevents sliding does not, on its own, guarantee that the item cannot overturn.

3Longitudinal distribution and axle loads

A rigid truck with three secured crates distributed lengthwise along its flatbed rests on portable scales beneath its front and rear axles.
The key idea

Respect the total weight limit and the weight limits for each axle.

Where you put the loadUsual effect
Further forwardsMore weight on the front support
Near the rear axleMore weight on that axle
Behind the rear axleMay overload it and remove weight from the front axle

Remember

  • Use your lorry’s load distribution diagram.
  • Avoid concentrating weight behind the rear axle.
  • Check the front axle when loading near the cab too.
  • Weigh each axle when necessary.

Exam trap: Wrong: meeting the total weight limit is enough. Right: check each axle too.

Read the full explanation
  • You must comply simultaneously with the vehicle's maximum mass, the maximum axle masses and the minimum loads needed to maintain its functions. Your loading plan must take all these limits into account; complying with the total mass limit does not guarantee an acceptable distribution. [RD 563/2017, Annex III.I.2](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • If you move a load forwards, you generally increase its contribution to the load on the front axle; if you move it closer to the rear axle, you increase the share supported by that axle. You must use the vehicle's load distribution diagram when available, because the correct position depends on its wheelbase, unladen axle masses and configuration.
  • Avoid concentrating heavy goods on the rear overhang. Mass behind the rear axle can overload that axle and reduce the load on the front axle, impairing steering. You must not group everything next to the cab either without checking the front axle load and the strength of the headboard.
  • Check the distribution using reliable data and, where necessary, by weighing each axle. It is not enough for the lorry to look level or for you to observe the tyre pressures. You study the full mass and dimension tables in the «Lorry dimensions and masses» module; here you must know how to apply them to your stowage plan.

4Dividing and distributing goods

A rigid truck travels to the right with pallets of metal parts and boxes distributed along its flatbed and secured with orange straps.
The key idea

Distribute goods with the whole journey and each delivery in mind.

Remember

  • Consider each pallet’s weight and position.
  • Include supports, packaging, equipment and people in your weight check.
  • Use suitable supports to spread concentrated weight.
  • Check that these supports cannot move.
  • Plan how your load will remain after each delivery.

Exam trap: Wrong: rows with equal numbers of items weigh the same. Right: check each pallet’s weight.

Read the full explanation
  • When the goods are divisible, distribute the units to make use of the supports without creating excessive concentrations. You must consider the mass of each pallet and its position, not just how many pallets you place in each row. Two rows with the same number of items can have very different weights.
  • You must include supports, packaging, equipment and occupants when checking the actual mass for the journey. Do not confuse the theoretical capacity available with authorisation to load that same quantity of goods anywhere in the load body. You can reach an axle limit or the floor's load-bearing capacity before reaching the overall maximum.
  • For a concentrated load, use supports or load-spreading elements suited to the goods and the floor. Their purpose is to distribute forces and prevent damage or collapse; you must check that they cannot move. An improvised plank does not demonstrate sufficient capacity to support a machine or a heavy item.
  • Plan your deliveries before loading. If unloading one consignment first leaves all the heavy goods at the rear, you can end up with an unsuitable distribution after the first stop. You must plan for every intermediate stage of the journey, not just how the lorry is loaded when it leaves the warehouse.

5Choosing the load body, packaging and supports

A rigid truck parked beside the kerb carries film-wrapped boxes on an intact pallet, with wooden supports and two lashing straps secured to the platform.
The key idea

Choose a vehicle, packaging and supports that let you secure your goods safely.

Vehicle bodyWhat you must check
Flatbed without sidesRestraint in every necessary direction
Enclosed bodyStrength of walls and doors

Remember

  • Set aside broken pallets and packaging that prevent safe securing.
  • Check the strength of walls, doors and supports.
  • Respect the weight that stacked packages can support.
  • Check both connections: goods to pallet, and pallet to lorry.

Exam trap: Wrong: pallet wrapping secures it to the lorry. Right: secure the pallet to the lorry too.

Read the full explanation
  • You must choose a vehicle suited to the goods and packaging that allows you to secure them. A broken pallet, a crushed box or a machine without suitable securing points can prevent safe stowage. The inspection expressly covers the suitability of the vehicle and packaging. [RD 563/2017, Annex III.II](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • On a flatbed without sides, you must provide for restraining the items in every relevant direction. In an enclosed load body, the walls do not have unlimited strength either. You must check what forces the headboard, sides, doors and stanchions can withstand before using them as part of the securing system.
  • If you stack items, respect their ability to withstand compression and place the strongest and heaviest ones in positions compatible with the load as a whole. Packaging that gives way leaves slack in the lashings and can allow movement. Protect fragile goods without allowing the cushioning to become an unstable support.
  • You must distinguish between the strapping that groups boxes on a pallet and the devices that secure that pallet to the lorry. Packaging film can hold the load unit together, but it does not demonstrate that the unit is restrained relative to the vehicle. You must check both connections: between the products and their support, and between the support and the load body.

6Forces the securing system must withstand

A rigid truck facing right travels in the lane nearest the viewer, with the dashed centre line behind it and a load secured by diagonal lashings towards the rear and a top-over lashing.
The key idea

Prepare your securing system to withstand braking, acceleration and cornering.

0.8Weight multiplier: forwards
0.5Weight multiplier: sideways
0.5Weight multiplier: backwards
Your manoeuvreLoad movement
BrakingForwards
AcceleratingBackwards
TurningTowards the outside of the bend

Remember

  • Calculate forces by multiplying the load’s weight by the values shown.
  • Prevent your load from sliding, tipping or rolling.
  • Allow for heavy braking even when you normally drive smoothly.
  • Combine methods according to the forces they can withstand together.

Exam trap: Wrong: a heavy load cannot move. Right: secure heavy loads too.

Read the full explanation
  • You must size the system for forces equivalent to the weight of the load multiplied by 0.8 forwards, 0.5 sideways and 0.5 rearwards. These are the acceleration and deceleration criteria in the load-securing annex; they are not percentages of the load that you can leave unsecured. [RD 563/2017, Annex III.I.1](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • You must also prevent the load from tipping lengthways or sideways. You must therefore assess sliding, overturning and, where relevant, rolling separately. A tall item may not slide on a high-friction surface and yet still tilt until it falls.
  • When you brake, the goods tend to keep moving forwards relative to the load body; when you accelerate, they can tend to move rearwards, and when you turn, towards the outside of the bend. You must allow for these forces even if you normally drive smoothly: an emergency can require hard braking.
  • You can combine locking, blocking, direct lashing and top-over lashing. You must assess how the system works as a whole, including friction and supports, without adding together capacities that do not act in the same direction or that depend on a weak component. [RD 563/2017, Annex III.I.4](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).

7What the EN stowage standards mean

A worker inspects a lashing strap and its anchor point on a parked rigid truck carrying a large crate secured with several straps on anti-slip pads.
The key idea

Use stowage standards to choose and calculate your load securing system.

StandardWhat you use it for
EN 12195-1Calculating lashing forces
EN 12195-2Synthetic straps
EN 12195-3Chains
EN 12195-4Steel wire lashing ropes
EN 12640Lashing points
EN 12642Bodywork strength

Remember

  • Calculate lashings using weight, friction, position and method.
  • Check each component’s capacity and condition.
  • Respect the strength of lashing points.
  • Never invent capacity or friction values.

Exam trap: Wrong: a strap per pallet is enough. Right: calculate the securing needed.

Read the full explanation
  • You must associate EN 12195-1 with the calculation of lashing forces. The number and capacity of the securing devices depend on mass, friction, geometry and method; there is no universal rule of one strap per pallet. [RD 563/2017, Annex III.I.5](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • EN 12195-2 covers synthetic webbing straps, EN 12195-3 covers chains and EN 12195-4 covers steel wire lashing ropes. Your choice depends on the goods and the conditions of use. A thick strap or a chain that looks strong is no substitute for information about its capacity and condition. [RD 563/2017, Annex III.I.5](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • You must associate EN 12640 with lashing points and EN 12642 with vehicle body strength. A high-capacity device loses its usefulness if you connect it to a point that cannot withstand the force. Check the declared specifications of each component and do not assume that a wall has the strength of the chassis. [RD 563/2017, Annex III.I.5](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • To answer test questions, you must recognise these principles and distinguish between the methods. In an actual operation, use the calculations and instructions applicable to the specific system; general acceleration figures are not enough for you to judge intuitively how many lashings you need.

8Blocking and immobilisation

A rigid truck carries a horizontal pipe secured with two straps, supported in bolted cradles and blocked by stops with spacers at both ends.
The key idea

Block your load with strong supports that cannot move.

Remember

  • Check headboard and side strength before using them as supports.
  • Fill necessary gaps with suitable materials.
  • Use suitable cradles or load chocks for items that can roll.
  • Add other securing where needed.
  • Check blocking after loading and unloading.

Exam trap: Wrong: preventing rolling is enough. Right: prevent movement in other directions too.

Read the full explanation
  • You must understand blocking as restraint through contact with components capable of taking the thrust of the load. You can use supports, spacers, bars, cradles or suitable structures. Their effectiveness depends on transmitting the force to a strong part of the vehicle and remaining in place.
  • If you use the front wall or side walls for blocking, check their capacity and conditions of use. Do not leave gaps that allow the goods to gain momentum before striking the support. Fill the necessary spaces with components designed to withstand the expected force without damaging the packaging.
  • For pipes, coils or other items that can roll, use suitable cradles or load chocks and additional securing where appropriate. Do not confuse them with the chocks used under the lorry's wheels when parked. Preventing an item from rolling does not prove that it is restrained forwards, backwards and sideways.
  • You must make sure that vibration or settling does not loosen the blocking. A loose wedge that can be thrown out creates a second hazard. Check the whole arrangement after loading and unloading, especially if removing one package also removes the support that holds the others in place.

9Friction and anti-slip materials

A rigid flatbed truck carries a crate on a pallet with green anti-slip mats beneath its supports and two tie-down straps secured to the flatbed.
The key idea

Use friction to help secure your load, and check the whole system.

Remember

  • Clean the floor and supports before loading.
  • Check the materials touching each other and their condition.
  • Place anti-slip mats at the points supporting your load.
  • Check their capacity, cleanliness and condition.
  • Allow for tipping and rolling too.

Exam trap: Wrong: a mat always replaces lashings. Right: check the complete securing system.

Read the full explanation
  • Friction between the load and its support resists sliding. You must assess the materials actually in contact and their condition, because clean, oily and icy surfaces behave differently. An item's heavy weight alone does not guarantee that it remains stationary.
  • As part of your preparation, clean the load floor and supports and remove debris that can roll, slide or contaminate the contact surfaces. A good lashing plan becomes less effective if you place the pallet on dirt or loose material. Do not assume that any rubber has a high coefficient of friction without knowing its performance.
  • You can use suitable anti-slip mats to improve contact. You must place them at the load's support points, respect their capacity and check that they are not damaged or contaminated. The material must retain its function under the intended load; a crushed or poorly positioned piece may not provide the effect you allow for in your calculations.
  • Your system must also deal with tipping, rolling and forces in all necessary directions. Friction contributes to load securing, and you must justify the value you use; it does not authorise you to drive with goods simply resting on the load floor.

10Top-over lashing and direct lashing

A flatbed truck is stationary in a loading yard without kerbs, carrying a crate secured by orange top-over straps with edge protectors and green direct lashings connected to the bed anchors.
The key idea

Understand how top-over lashing and direct lashing secure your load differently.

TermWhat you must remember
Top-over lashingPresses the load down and increases friction
Direct lashingRestrains the load according to the lashing’s direction
LCLashing capacity
STFStandard tension force: initial tension

Remember

  • Protect edges to prevent cuts in your straps.
  • Keep edge protectors in place throughout your journey.
  • Do not crush packaging when tightening straps.
  • Check each device’s label and intended method of use.

Exam trap: Wrong: LC tells you how much you can lift. Right: it states lashing capacity.

Read the full explanation
  • With top-over lashing, you run the lashing over the load and tension it towards the anchorages. The added pressure increases friction against the support, so the pretension and strap angle matter. You must not confuse this effect with directly restraining a package in a particular direction.
  • With direct lashing, you connect the load or its restraint system to strong points on the vehicle. The lashings resist movement according to their orientation. You must arrange them to restrain movement in the required directions, because a lashing that runs almost lengthways does not provide the same lateral restraint as one with a different geometry.
  • You must protect edges to prevent them from cutting the straps and to spread the pressure without damaging the goods. The protectors must remain in place throughout the journey. Do not tighten the lashings enough to deform fragile packaging: if it collapses, you can lose tension and, with it, some of the lashing's effectiveness.
  • Lashing capacity LC and standard tension force STF are different specifications; use the one appropriate to the securing method and the equipment information. LC does not mean that you can lift that mass with the strap or that its value is equivalent to pretension. To use a device, you must follow its intended method of use and its label. [Gobierno Vasco (Basque Government), Load stowage guide](https://www.euskadi.eus/gobierno-vasco/-/documentacion/2019/guia-vasca-de-estiba-para-el-transporte-de-mercancias-por-carretera/).

11Checking straps, chains and anchorages

A worker inspects the webbing and stitching of a ratchet strap beside a flatbed truck parked in a loading area with no kerb or roadway.
The key idea

Check every securing component before you use it.

Remember

  • Set aside damaged straps, chains and hooks, or those without enough identification.
  • Do not repair them with knots or improvised joins.
  • Close tensioners and gather loose ends.
  • Use the intended lashing points and respect their strength.
  • Prevent rubbing that damages lashings.

Exam trap: Wrong: many straps guarantee safety. Right: check how they restrain each item.

Read the full explanation
  • Before use, you must inspect webbing, stitching, hooks, tensioners, chains and anchorage points. Set aside components with cuts, deformation, deterioration or insufficient identification to determine their safe use. Do not try to restore capacity with knots, improvised joins or repairs not specified by the manufacturer.
  • You must attach each device in a way compatible with its design and avoid loading edges or parts of the hook not designed to bear the force. Check that the tensioner is closed and protected against accidental opening. Secure loose ends so that they do not drag or strike other road users.
  • You must use the anchorages intended for securing loads and respect their strength limits. A step, hinge or lightweight side panel does not become a lashing point simply because you can run a strap through it. The usable strength of the assembly is limited by its components and the way forces act on them.
  • When you finish stowing the load, check that no lashing rubs against the goods or vehicle body in a way that causes damage. If you combine methods, confirm that they work together compatibly. You must be able to explain what prevents each unit from moving; seeing many straps over the load does not prove that the forces are correctly distributed.

12Tarpaulins, covers and bulk goods

A rigid truck travels along a rural road with its load body completely covered by a taut, secured green tarpaulin and its tailgate closed.
The key idea

Cover goods that can fall or produce dust, and secure the cover too.

EquipmentWhat you must check
CoverPrevents the product escaping
NetMust retain the product; open mesh lets fine dust escape
Load restraint structureMust withstand forces from the load

Remember

  • Always cover these materials, whatever your route or speed.
  • Keep the cover closed throughout your journey.
  • Check tailgates and sides.
  • Spread material without heaps that could spill.
  • Secure your tarpaulin and tensioners without covering lights or plates.

Exam trap: Wrong: an ordinary side curtain secures pallets. Right: provide suitable load restraint.

Read the full explanation
  • You must completely and effectively cover materials that produce dust or can fall off. You must always cover them, regardless of the route or speed. The cover must be suitable for the product you carry and remain closed throughout the journey. [RGC, art. 14.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • Check the fastenings on tailgates and side panels before carrying aggregates or other bulk goods. Distribute the material without creating piles that make it more likely to fall off or unnecessarily raise the centre of gravity. A correctly fitted tarpaulin does not compensate for an open tailgate or a container that leaks material from underneath.
  • You must also secure the tarpaulin itself, its tensioners and the equipment used to fit it. Avoid loose ends that can come free, strike others or cover lights and plates. A net only serves as a cover if it effectively retains the material: an open mesh does not prevent fine dust from dispersing.
  • A cover protects the goods; you can only rely on a structure to restrain them if its strength is verified for that use. Protection against rain or dirt and restraint during braking are different functions that you must address in your loading plan.

13Liquids and surge in tankers

A tanker truck travels in its lane around a left-hand bend, with the liquid in its partially filled tank displaced towards the outer right side of the bend.
The key idea

Anticipate liquid movement and its effects on your tanker’s stability.

Remember

  • Expect liquid surge when you brake, accelerate or turn.
  • Remember that its effects can continue after your manoeuvre ends.
  • Know your tanker’s compartments and baffles.
  • Follow filling instructions for your equipment and product.

Exam trap: Wrong: baffles remove every risk. Right: they limit certain movements according to their design.

Read the full explanation
  • If you carry liquid in a partially filled tanker, you must anticipate its movement within the tank when you brake, accelerate or turn. This surge changes the mass distribution and exerts forces on the vehicle. You may feel its effects even as the manoeuvre that started it is coming to an end.
  • On a bend, liquid moving towards the outside reduces stability and can contribute to a rollover. When you brake, its longitudinal movement changes the forces on the supports. You must consider both the mass carried and the space available for the liquid to move, as well as the shape of the tank.
  • Compartments and baffles limit certain movements of the liquid according to their design. You must know your tanker's configuration and how the different compartments are loaded; you cannot assume that all tanks have the same divisions or that these eliminate every risk of surge.
  • You must follow the filling instructions and respect the permitted capacity for the equipment and product. There is no single percentage that makes every tanker safe in terms of stability; the quantity, design and distribution all matter together. The specific filling conditions for dangerous goods are covered in the ADR course. [RD 97/2014, art. 43](https://www.boe.es/buscar/act.php?id=BOE-A-2014-2110#a43).

14Hanging loads and swinging

A rigid refrigerated truck follows a bend in its right-hand lane, with a cutaway view of meat carcasses hanging from rails with locking mechanisms.
The key idea

Prevent hanging loads from swinging and reducing your lorry’s stability.

Remember

  • Slow down before bends.
  • Steer, brake and accelerate smoothly.
  • Use the locking devices provided and check their closures.
  • Control swinging when your crane lifts an item.
  • Before driving, stow and secure the boom, hook and accessories.

Exam trap: Wrong: you can ignore swinging. Right: it can shift the centre of gravity and make overturning more likely.

Read the full explanation
  • In a lorry carrying meat carcasses on rails or hanging garments, you must anticipate the goods swinging. When you turn, the load can move outwards and rise from its resting position; when you brake, it can swing forwards and rise. These movements shift the centre of gravity of the vehicle and load together and reduce stability. [RGCond, annex V.B.2.4.º k)](https://www.boe.es/buscar/act.php?id=BOE-A-2009-9481#av).
  • You must reduce your speed before bends and use the steering, brake and accelerator smoothly to limit swinging. Use the equipment's locking bars and fasteners to immobilise the load and its supports; check that they are secured before setting off. [RGC, art. 14.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14).
  • If you use a loading crane, you must control the swinging of the item suspended from the hook during the operation. Before driving, stow and secure the boom, hook and accessories in the transport position specified by the manufacturer. [RD 1215/1997, annex II.1.3 and II.3.2.b)](https://www.boe.es/buscar/act.php?id=BOE-A-1997-17824#anii).

15Driving and checking during the journey

A rigid truck with a tall load secured by tie-down straps travels in its right-hand lane as it approaches a bend on a rural road.
The key idea

Drive smoothly and check your load whenever it may have moved.

Remember

  • Slow down before turning.
  • Leave room to brake smoothly.
  • Check securing after your goods settle.
  • Check again after heavy braking or jolting.
  • Stop somewhere safe if you notice banging or leaning.
  • Assess the danger before opening doors with goods resting against them.

Exam trap: Wrong: lashings make every manoeuvre safe. Right: drive within your lorry’s stability limits.

Read the full explanation
  • With a high or moving load, you must take particular care to anticipate bends, roundabouts and lane changes. Slow down before turning and use the steering, accelerator and brake progressively. Good load securing withstands the expected forces, but does not make a manoeuvre safe if it is incompatible with the lorry's stability.
  • You must leave a margin that allows you to brake without constantly resorting to sudden actions. Your speed, grip, vehicle condition and load affect stopping. Do not work out a fixed safe following distance from weight alone or assume that driving with a partial load eliminates stability problems.
  • As a preventive measure, check the load securing after the goods initially settle and whenever circumstances warrant it, for example after heavy braking or a stretch of road that causes jolting. You must do this in a safe place. No universal distance interval applicable to all loads is specified here.
  • If you notice unusual banging, leaning or signs of movement, stop safely and arrange to correct the problem before continuing. Opening a door against which goods are resting can cause them to fall: assess the risk and request suitable equipment. Do not stand in the path of a load that could break free.

16Choosing where to load and unload

A truck unloads a pallet using its tail lift in a warehouse courtyard, completely off the road and with clear space around it.
The key idea

Load and unload off the road whenever possible.

Remember

  • Use the road only when unavoidable, without danger or serious disruption.
  • Respect stopping rules, parking rules and local loading places and times.
  • Outside built-up areas, stay on the right and off the carriageway.
  • Keep the usable hard shoulder clear.
  • Check ground, space and obstacles before entering a loading bay.

Exam trap: Wrong: unloading lets you double-park. Right: obey parking rules during unloading too.

Read the full explanation
  • You must load and unload off the road. You may use the exception allowing you to do so on the road only when it is unavoidable, without creating danger or serious disruption and while complying with stopping and parking rules and, in built-up areas, municipal rules on locations and times. [RGC, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16).
  • On an interurban road, you must stop or park off the carriageway, on the right, leaving the usable part of the arcén (hard shoulder) clear. [RGC, art. 90.1](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a90).
  • You must not double-park to deliver goods. Staying at the wheel does not in itself turn parking into stopping, and unloading does not create a general exception. Double-parking without a driver is also listed as a serious obstruction. [RGC, arts. 91 and 94](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a94).
  • Before entering a loading bay or work area, check that there is space to open doors, use the tail lift or operate equipment. As an operational precaution, assess the firmness of the ground, differences in level and overhead obstacles. A location that accommodates the lorry while driving may not allow you to carry out the intended operation safely.

17Preparing a safe operation

The driver and a worker coordinate in a protected pedestrian area beside a rigid truck with a rear wheel chock, while a forklift waits behind a barrier.
The key idea

Secure your parked lorry and coordinate with staff before starting work.

EquipmentYour precaution
CraneFirm ground, suitable supports and capacity for the reach used
Tail liftInclude the pallet jack’s weight
Pallet jackFirm, clear route; specific training if self-propelled

Remember

  • Agree with staff when you can move your lorry.
  • Use loading-bay devices according to site and vehicle procedures.
  • Keep the operation secure before allowing equipment into the load body.
  • Stabilise your load before releasing lashings.
  • Deploy crane stabilisers as instructed; keep people away from beneath suspended loads.
  • Respect tail lift and pallet jack capacities and instructions.

Exam trap: Wrong: use the tail lift as a passenger lift. Right: an operator may ride only if that use is provided for and the required safeguards are in place.

Read the full explanation
  • You must coordinate the operation with the staff on site and agree when the lorry can move. As a preventive measure, prevent a forklift from entering while the driver prepares to leave, and keep pedestrians separate from the route taken by loads. Do not drive off until you check that people and equipment are out of danger.
  • Loading bay restraint devices prevent the lorry from accidentally moving away from the bay during loading; you must use them according to the site's and vehicle's procedures. They serve a different purpose from securing the vehicle for parking, which is covered in ‘Manoeuvres with a lorry’, in the section ‘Secure your lorry on a gradient’. Keep the operation secure before allowing equipment into the load body.
  • Before removing lashings, identify what each one is restraining and the order in which you can release them without causing anything to fall. As a working practice, keep people clear of tensioners and parts that could move. You must stabilise the load using the necessary equipment before releasing the restraint that keeps it secure.
  • To use the lorry-mounted crane, you must deploy the stabilisers according to the manufacturer's instructions, on firm ground and with suitable supports. Respect the capacity specified for the reach and configuration you use, and keep people out of the area beneath the suspended load. [RD 1215/1997, annexes I.2.2 and II.3.1.a) and c)](https://www.boe.es/buscar/act.php?id=BOE-A-1997-17824#anii).
  • When using the rear tail lift, you must respect the permitted load and its positioning as specified by the manufacturer, including the pallet jack and any other items lifted with the goods. Do not use it as a passenger lift: an operator may be on it only if it is designed for that use and has the corresponding protective measures. [RD 1215/1997, annex II.1.3 and II.3.1.b)](https://www.boe.es/buscar/act.php?id=BOE-A-1997-17824#anii).
  • With a pallet jack, you must respect its capacity and use a firm, clear route, preventing the pallet from rolling or falling over an edge. Operate the equipment according to the instructions you receive; if it is self-propelled, you need specific training to drive it safely. [RD 1215/1997, art. 5 and annex II.2.1](https://www.boe.es/buscar/act.php?id=BOE-A-1997-17824#anii).

18Carrying out and completing unloading

A worker carries a box from a truck parked beside the kerb to a warehouse, with the road and pavement clear of goods.
The key idea

Unload without creating obstacles, and prepare your lorry before leaving.

Remember

  • On the road, work nearest the carriageway edge where possible.
  • Avoid unnecessary noise and inconvenience.
  • Never place goods on the carriageway, hard shoulder or pedestrian areas.
  • Before tipping, check firm, level ground and clear space above.
  • Stow tools and secure doors, tailgates and the tail lift.
  • Lower the tipper body and disconnect any site connections before driving.

Exam trap: Wrong: leave packages briefly on the pavement. Right: you cannot place them there during unloading either.

Read the full explanation
  • If operating on the road is unavoidable, you must work, as far as possible, on the side nearest the edge of the carriageway and have sufficient equipment and resources to finish quickly, avoiding unnecessary noise and disturbance. [RGC, art. 16.b and c](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16).
  • You must not place goods on the carriageway, hard shoulder or pedestrian areas, even if you only intend to leave them there while you bring a forklift over. An authorised loading and unloading time does not authorise you to place goods there. You must organise their movement between the lorry and the destination without using these spaces as temporary storage. [RGC, art. 16.c](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a16).
  • As a precaution with tippers, check for firm support, level ground and overhead clearance before raising the body, and keep the area where the material falls clear. If material sticks, do not try to dislodge it using improvised manoeuvres that compromise stability. Use the manufacturer's procedure and the site's equipment.
  • Before leaving, you must stow tools, secure doors, gates and the tail lift, and check that the tipping body is in its driving position. Also check that no hoses or connections remain attached to the installation if you use them. Completing the transfer or unloading does not mean that the vehicle is ready to move.

19Who can take part in the operation

A driver observes the load secured with straps in a heavy truck while a warehouse worker moves a pallet with a manual pallet jack.
The key idea

Check whether you may personally help with loading or unloading.

7.5 tGeneral ban above this MMA
Part-load case: goods vehicles above 7.5 t MMAConditions for your participation
Unloading only: distribution centre to point of saleIt must not affect your daily rest or, where applicable, must take place within your daily working hours; you must be able to return to your usual operating centre or home.
Loading and unloading: distribution centre to point of sale, or reverseAlso, a consignor–carrier contract lasting at least one year.

Remember

  • Above 7.5 t MMA, you generally cannot load or unload, with exceptions.
  • MMA means your vehicle’s maximum authorised mass.
  • The ban includes supports, packaging, containers and cages.
  • Check the specific exception before taking part.
  • Even if you do not load, check how the goods are stowed and secured.
  • For unloading only in the case below, no one-year contract is needed.

Exam trap: Wrong: if you do not load, you need not check. Right: check that you can drive safely.

Read the full explanation
  • If you drive a goods vehicle with an MMA (maximum authorised mass) of more than 7.5 tonnes, you are generally prohibited from taking part in loading or unloading, including supports, packaging, containers and cages. You must check the exceptions for the specific operation; the threshold refers to the MMA. [LOTT, thirteenth additional provision](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#da).
  • You may find exceptions for removals and furniture storage, tankers, aggregates, tippers or vehicles fitted with integral loading and unloading equipment, car transporters and recovery vehicles. The exception depends on the type of transport and the equipment specified by law; using an external forklift does not make the vehicle one fitted with integral loading and unloading equipment. [LOTT, DA 13.ª.1.a) to d)](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#da).
  • When unloading part-load consignments between a distribution centre and the point of sale, you may take part if the activity does not affect your daily rest or, where applicable, takes place within your daily working hours, and allows you to return to your usual operating centre or your home. This unloading-only exception does not require a one-year contract. [LOTT, DA 13.ª.1.e)](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#da).
  • To take part in both loading and unloading part-load consignments between a distribution centre and a point of sale, or in the reverse direction, you must also meet the condition of a contract between the consignor and the carrier lasting at least one year. [LOTT, DA 13.ª.1.e)](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#da).
  • Part-load consignments require prior handling, consolidation, sorting or similar operations. You may also find exceptions for parcel delivery and similar services involving a small number of packages that one person can easily handle, live animals at control posts approved under EU rules, and transport operations whose rules specifically allow you to take part. Cases established by regulation are also permitted, with your safety guaranteed. These participation rules apply to all operations carried out in Spanish territory. [LOTT, DA 13.ª.1.e) to h) and 2](https://www.boe.es/buscar/act.php?id=BOE-A-1987-17803#da).
  • Even if you do not physically take part, you must know the outcome of the stowage and check that you can drive safely. Do not confuse this employment-related prohibition on taking part with an exemption from checking the load. If you notice unsafe distribution or inadequate restraint, you must resolve it with those carrying out the operation before you drive.

20Partial unloading and restowage

A worker checks a lashing on the remaining pallets in a truck with its side open and an empty space after partial unloading, beside an unloaded pallet on the loading dock.
The key idea

After each delivery, check weight distribution and secure your remaining load.

Remember

  • Check axle weights and balance between both sides.
  • Replace blocking or adjust lashings if gaps appear.
  • In tankers, follow the specified unloading sequence.
  • Check closures after each operation.
  • Reposition markings and secure tarpaulins when your load changes.

Exam trap: Wrong: removing weight always improves distribution. Right: check the load on each axle again.

Read the full explanation
  • After each delivery, you must check the distribution between axles and sides and secure the remaining load again. Removing goods reduces the total mass, but does not guarantee a better load at every support point: removing a counterweight can increase the load borne by another axle. You must assess the new arrangement, not just how much weight you have removed.
  • If the pallets block one another in place, removing a row can leave the remaining units free to move. You must restore the blocking or adapt the lashings before setting off. Do not retain an arrangement designed for a full load body when the gaps created allow the load to slide or strike the walls.
  • In tankers with several compartments, you must anticipate how unloading each one affects longitudinal distribution. A tanker with less liquid can still present a significant risk from load movement and uneven distribution. Follow the operating sequence specified for the equipment and check the closures after each operation.
  • You must also check the signs and covers after changing the load. If the projecting end changes, the panel must remain in the appropriate position; if a tarpaulin comes loose, you must secure it again. Your check before the first journey does not automatically cover all subsequent stages.

21When a load can project

A truck travels to the right in the nearest lane carrying secured beams that project beyond its front and rear, with a V-20 panel at the rearmost end of the load.
The key idea

Check whether your indivisible load may project, and by how much.

5 mVehicle length threshold
2 mFront: vehicle over 5 m
3 mRear: vehicle over 5 m
Goods-only lorry length: indivisible loadsMaximum front projectionMaximum rear projection
Over 5 m2 m3 m
5 m or lessOne third of vehicle lengthOne third of vehicle length

Remember

  • Normally, keep your load within your vehicle’s outline.
  • For goods-only lorries, exceptional projections require indivisible loads, properly prepared and secured.
  • Measure each projection from the corresponding end of your vehicle.
  • Also check overall dimensions, weight, supports and markings.

Exam trap: Wrong: use the larger projections at exactly 5 m. Right: allow one third of vehicle length at each end.

Read the full explanation
  • As a general rule, you must keep the load within the vehicle's footprint when viewed from above. For your lorry intended exclusively for goods, the usual exceptions allowing projections require an indivisible load that is properly arranged and secured. [RGC, art. 15.1 and 2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • If your vehicle is more than 5 m long and you carry beams, posts, pipes or other objects of indivisible length, they may project by no more than 2 m at the front and 3 m at the rear. You must measure each projection from the corresponding end of the vehicle. [RGC, art. 15.2.a](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • If your vehicle is 5 m long or less, the maximum projection is one third of its length at each end, front and rear. You must include equality: exactly 5 m falls within this case. For that length, each third is approximately 1.67 m; you must calculate using the exact value so that you do not exceed the limit when measuring. [RGC, art. 15.2.a)](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • To calculate the projections, you must measure the length of the object and the overall length of the loaded vehicle separately. On a 7 m lorry, you can position a 9 m beam with permitted projections; a 12 m piece can span those 7 m plus 2 m at the front and 3 m at the rear. You must also check overall dimensions, masses, supports and marking and lighting before concluding that the transport is permitted.

22Side projections and overall dimensions

A rigid truck travels in the right lane carrying an orange slab secured with two straps that projects slightly beyond both sides of the flatbed.
The key idea

Respect permitted projections and overall dimensions at the same time.

0.40 mMaximum projection on each side
2.55 mOrdinary maximum overall width
12 mOrdinary rigid lorry maximum length
4 mOrdinary maximum height

Remember

  • Side projection requires an indivisible load whose smallest dimension exceeds your lorry’s width.
  • Check dimensions including your load, and any route restrictions.
  • Do not add permitted projections to maximum overall dimensions.
  • If required, obtain additional road-use authorisation before driving and follow its conditions.

Exam trap: Wrong: applying for additional road-use authorisation lets you leave. Right: obtain it first and follow its conditions.

Read the full explanation
  • If the smaller dimension of an indivisible load exceeds the width of your lorry, it may project by up to 0.40 m on each side, provided the overall width does not exceed 2.55 m. You must meet both limits at the same time. [RGC, art. 15.2.b](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • You must check the external dimensions including the load and the restrictions on your route. For an ordinary rigid lorry, the general maximum dimensions are 12 m long, 2.55 m wide and 4 m high, without applying specific exceptions. You cannot add the permitted projections as authorisation to exceed these maximum dimensions. [RGV, annex IX.3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anix).
  • If your rigid lorry is already 12 m long, you cannot add a projection that exceeds the general length limit by relying solely on the 2 and 3 m rule. Check when you need an autorización complementaria de circulación (additional road-use authorisation) in «Lorry dimensions and masses», section «When you need special transport». [RGC, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a13).
  • You can consult the example of an 11 m lorry with a 14.5 m post in «Lorry dimensions and masses», section «When you need special transport».

23Protection and the V-20 panel

A truck travels in the right lane with beams projecting from the rear, their ends protected with orange padding and a red and white V-20 panel secured to the rearmost end of the load.
The key idea

Protect projecting loads and correctly position the V-20 panel at the rear.

Rear projectionPanels you must fit
Does not cover the full rear widthPlace the V-20 at the projecting end
Covers the full rear widthFit two panels, one at each end; stripes form an inverted V

Remember

  • Protect projecting ends against scraping and collisions.
  • Use the regulation panel with reflective red and white stripes.
  • Place it at the load’s rearmost end, perpendicular to your vehicle’s length.
  • Fix it securely and keep it visible, including in daylight.

Exam trap: Wrong: replace the panel with a red cloth. Right: use the regulation panel.

Read the full explanation
  • When your load projects, you must protect its end and take precautions to prevent damage from scraping or collisions. A visible panel does not eliminate the danger of a sharp edge. You must address physical protection of the end and warning other road users separately. [RGC, art. 15.5](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • You must mark a load projecting at the rear with the V-20, the regulation panel with reflective red and white diagonal stripes. Place it at the rear end of the load and keep it perpendicular to the vehicle's longitudinal axis. Simply carrying it inside the cab or attaching it to the door is not enough if it is ahead of the projecting end. [RGV, annex XI, V-20](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-20).
  • If your load projects lengthways across the full rear width of the vehicle, you must place two panels transversely, one at each end of the load or projecting material. Arrange their stripes to form an inverted V. [RGC, art. 15.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • You must secure the panel firmly and keep it visible and in good condition. You cannot replace it with a red cloth or a painted piece that imitates its colours. You must also mark the rear projection during the day; this requirement does not depend on the journey being short or the projection seeming small to you.

24Lighting for projecting loads

A lorry travels to the right at night in the near lane, with a red light and a V-20 panel at the end of the beams projecting beyond its rear.
The key idea

Add the required lights to projecting loads at night or when visibility is substantially reduced.

0.40 mSide threshold from position light
ProjectionAt night or with substantially reduced visibility
RearRed light and V-20 panel
FrontWhite light
Side: more than 0.40 m from the position light’s outer edgeAt each affected side end: white light and reflector forwards; red light and reflector backwards

Remember

  • At the rear, keep your V-20 and add a red light.
  • At the front, add a white light even for a small projection.
  • Measure the side threshold from the outer edge of the matching position light.
  • This measuring point differs from the one used for the permitted projection.

Exam trap: Wrong: a light replaces your V-20. Right: retain the rear panel and add a red light.

Read the full explanation
  • Between sunset and sunrise, or if weather or environmental conditions significantly reduce visibility, you must add a red light to a load projecting at the rear. You must also retain the V-20: the lighting and the panel serve complementary purposes. [RGC, art. 15.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • If your load projects at the front, you must mark it with a white light in those conditions of darkness or reduced visibility. You must position the warning so that others can identify the actual end, and you must not obscure the lorry's mandatory lights. [RGC, art. 15.6](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • For side marking and lighting, you must measure from the outer edge of the corresponding front or rear position light. If the side extremity of your load is more than 0.40 m from that edge, you must mark and light it at night or when visibility is significantly reduced. This measurement point differs from the one used to determine whether a side projection is permitted. [RGC, art. 15.7](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).
  • At each affected side extremity, you must fit a white light and white reflector facing forwards, and a red light and red reflector facing rearwards. First you check that the transport falls within the permitted rules, then you check its marking and lighting. [RGC, art. 15.7](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a15).

25Keeping the road clean and free of obstacles

A worker uses a brush and bucket to collect stones from the rear ledge of a truck with its load covered, stopped in a loading area beside a clean road.
The key idea

Prevent spills and safely remove obstacles you cause.

Remember

  • Check tailgates, edges and equipment when leaving a worksite or unloading area.
  • Stow packaging, tools and loose material that could fall.
  • Never clean your load body by dropping waste onto the road.
  • If you create danger, warn others while arranging safe removal.
  • Ask for help if you cannot deal with it yourself.
  • Correct the cause of any spill before continuing.

Exam trap: Wrong: continue after a spill with a faulty closure. Right: fix the cause before leaving.

Read the full explanation
  • You must prevent goods, packaging, dust or waste from escaping from the load body. You must not throw, deposit or leave materials that make traffic dangerous or damage the road. A spillage of grain, aggregates or liquid can particularly affect road users on two wheels. [RGC, art. 4.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a4).
  • As a preventive check when leaving a construction site or unloading area, check gates, edges and equipment for debris and avoid carrying mud or loose stones that could fall off. You must keep packaging materials and tools tidied away. Cleaning the load body by letting its contents fall onto the road is not an acceptable way to finish the job.
  • If you create an obstacle or hazard, you must remove it as soon as possible and, in the meantime, take measures to make other road users aware of it and prevent traffic from being obstructed. You must arrange for safe removal and ask for help if you cannot deal with it using your own resources. [RGC, art. 5](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a5).
  • Before you set off again after a spillage, you must correct its cause: a faulty fastening or a poorly secured cover can cause another loss of load. You study the detailed action to take when your vehicle is immobilised or in an emergency in «Accidents, breakdowns and first aid», in the section «Fallen loads and lorry-specific risks».

26Final check and stowage inspection

A driver checks a strap tensioner securing wooden crates on a rigid truck parked beside the kerb, with its latches and rear lights visible.
The key idea

Check every aspect of your load’s safety before driving.

DeficiencyWhat it means
MinorSecuring is correct; recommendations may be given
MajorSignificant movement or overturning is possible
DangerousDirect danger, such as immediate load loss or harm to people

Remember

  • Check position, weights, supports and securing.
  • Check closures, covers, dimensions and markings.
  • Look from outside to check that lights and plates remain visible.
  • Know your securing system’s details to help with an inspection.

Exam trap: Wrong: a tidy load is securely held. Right: check the securing system’s strength.

Read the full explanation
  • You must complete the check in this order: load position and masses, supports, restraint, fastenings, covers, dimensions and marking and lighting. Check lights and plates from outside the lorry. A load can meet the requirements of the first part of the check and fail another part; you must meet all the conditions before driving.
  • During a roadside inspection, inspectors may visually check the load, measure tensions, calculate the effectiveness of the securing arrangements and check certificates where applicable. You must know the characteristics of the arrangement to help them check it. A tidy outward appearance does not replace the necessary strength. [RD 563/2017, art. 11 and Annex III.II](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • A deficiency is minor when the load is correctly secured but recommendations can be made, and major when the securing is insufficient and there is a possibility of significant movement or overturning. It is dangerous if it creates a direct hazard, for example an immediate risk of losing the load or injuring people. [RD 563/2017, Annex III.II.1](https://www.boe.es/buscar/act.php?id=BOE-A-2017-6512#ai-3).
  • For the exam, you must reason through each scenario in this order: what goods you carry, how they are distributed, what keeps them in place and what warnings they require. Do not confuse knowing how to stow a load with loading it yourself, signalling with authorising, covering with lashing, or meeting the total mass limit with meeting each axle limit. These distinctions help you answer questions with very similar options.

Preparing and securing a load

Procedure for setting off with your lorry correctly loaded.

  1. Identify the mass, dimensions, supports and orientation of each unit and check that the vehicle is suitable.
  2. Plan the distribution across axles and sides, keeping heavy items low and taking partial deliveries into account.
  3. Clean the supporting surfaces and fit the necessary load-spreading, anti-slip and blocking equipment.
  4. Fit and tension the lashings as calculated; check anchorages, edge protection and measures to prevent tipping or rolling.
  5. Close and secure doors, tailgates and covers; measure any projections and fit the appropriate signs and lights.
  6. Carry out the final exterior check and schedule the checks required by the load and route.

Loading or unloading safely

From choosing the location to setting off again.

  1. Choose a location off the road; if working on the road is unavoidable, check restrictions, permitted times and the absence of danger.
  2. Check who can take part, coordinate the work and immobilise the lorry as required by the location and the site procedure.
  3. Stabilise the goods before opening or releasing the equipment that restrains them.
  4. Move packages using adequate equipment, without placing them on the carriageway, arcén (hard shoulder) or pedestrian areas.
  5. Check the distribution and secure the remaining load again.
  6. Collect equipment and connections, close the load body, check cleanliness and markings, and confirm that you can move.

Dealing with a projecting load on your lorry

Check authorisation, dimensions and markings separately.

  1. Confirm that the load meets the permitted conditions for an indivisible load on a vehicle used exclusively to carry goods.
  2. Apply the longitudinal limit according to whether the vehicle is over 5 m long or up to and including 5 m; also check the side limits.
  3. Measure the overall dimensions and check route restrictions; obtain supplementary authorisation in advance if required.
  4. Protect the ends and secure the goods.
  5. Fit the rear V-20 panel; use two panels forming an inverted V if the load projects across the full width at the rear.
  6. Add the lights and reflectors required according to the direction of projection, distance from the position lights and visibility.

Checking after a partial delivery

Unloading changes both the supports and the restraint system.

  1. Identify the units or compartments that remain loaded.
  2. Recalculate or check axle load distribution and lateral balance.
  3. Locate gaps and supports that are no longer present.
  4. Adapt blocking and lashings to the new load condition.
  5. Check closures, covers, projections and markings before continuing.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1At an unsigned narrow passage, with no steep gradient or instructions from officers or authorised personnel, two vehicles of the same type must decide which reverses. Neither has priority from entering first and both would reverse the same distance. Which dimensions or mass are considered for priority?
2Under Spain’s vehicle-use classification, a vehicle carries goods in a fully enclosed compartment, with no padding or special interior adaptation and no bulk-material tank. Which designation applies?
3A lorry used exclusively for goods transport is exactly 5 metres long. It carries indivisible-length posts with proper stowage and securing, without a special-transport authorisation. What is the maximum longitudinal overhang?
4You park a 6,000 kg MAM lorry with a manual gearbox on an 8% uphill slope and will leave the driving position. The parking brake is applied and proper wheel chocks are available, but there is no usable kerb. What else must you do?

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module