Theory · C+E Licence - Articulated Truck · Module 3 of 13
You learn to determine the permitted masses and dimensions of your articulated vehicle or road train and check the limits for each axle and the road. You can answer questions on configurations, projections, exceptions and special transport without confusing actual mass with authorised mass.


Actual weight and your authorised maximum are different.
| Term | What you count |
|---|---|
| Unladen mass | Equipped vehicle without people or goods |
| Mass in running order | Unladen mass plus 75 kg for the driver |
| Laden mass | Actual weight with people and goods |
| MMA | Maximum authorised mass when laden |
Exam trap: Wrong: unloading lowers your MMA. Right: it lowers actual mass; your MMA stays unchanged.

Combination limits include the towing vehicle, towed units and coupling load.
Exam trap: Wrong: choose the higher coupling limit. Right: for a centre-axle trailer with evenly distributed load, use the lower of 10 % of its maximum mass or 1,000 kg.

You must meet every weight limit at the same time.
Exam trap: Wrong: inflate tyres to 9 kg/cm². Right: this limit concerns pressure on the road surface.

You must distinguish individual axle limits from whole-group limits.
| Single axle on your lorry | General maximum |
|---|---|
| Driven: propels the vehicle | 12 t |
| Non-driven: supports weight | 10 t |
Exam trap: Wrong: multiply a tandem limit by its axles. Right: apply that limit to the whole group.

For a motor-vehicle tandem, you must check axle spacing and equipment.
| Motor-vehicle tandem spacing | Group maximum |
|---|---|
| Below 1.00 m | 12 t |
| At least 1.00 m, below 1.30 m | 16 t |
| At least 1.30 m, below 1.80 m | 18 t; 19 t only under the stated conditions |
Exam trap: Wrong: nearby axles allow 19 t. Right: spacing must be at least 1.30 m but below 1.80 m. The driven axle needs twin tyres and air or recognised equivalent suspension. Alternatively, each driven axle needs twin tyres and must not exceed 9.5 t.

For a towed tandem, you must choose the limit by axle spacing.
| Trailer or semi-trailer tandem spacing | Group maximum |
|---|---|
| Below 1.00 m | 11 t |
| At least 1.00 m, below 1.30 m | 16 t |
| At least 1.30 m, below 1.80 m | 18 t generally |
| At least 1.80 m | 20 t |
| At least 1.30 m, below 1.80 m; semi-trailer with reinforced tipping body for construction, works or mining | 20 t |
Exam trap: Wrong: any tipping body allows 20 t with spacing from 1.30 m to below 1.80 m. Right: you need a semi-trailer with a reinforced tipping body specifically for construction, works or mining.

You must distinguish the tri-axle group maximum from the whole trailer maximum.
| Towed unit or group | Condition | General maximum |
|---|---|---|
| Trailer or semi-trailer tri-axle group | Consecutive spacings up to 1.30 m inclusive | 21 t |
| Trailer or semi-trailer tri-axle group | Consecutive spacings above 1.30 m, up to 1.40 m inclusive | 27 t |
| Whole trailer | Two axles | 18 t |
| Whole trailer | Three axles | 24 t |
Exam trap: Wrong: adding 10 t per axle allows a two-axle trailer 20 t. Right: its general maximum remains 18 t.

For a rigid lorry, you must check axle numbers and equipment conditions.
| Rigid goods lorry | General maximum and conditions |
|---|---|
| Two axles | 18 t |
| Three axles | 25 t; 26 t with the stated equipment |
| Four axles, including two steering axles | 32 t with the stated equipment |
| Other four-axle rigid lorries | 31 t |
Exam trap: Wrong: use 26 t or 32 t without checking equipment. Right: 26 t requires three axles; 32 t requires four with two steering axles. The driven axle needs twin tyres and air or recognised equivalent suspension. Alternatively, each driven axle needs twin tyres and a maximum of 9.5 t.

You may exceed a four-axle articulated vehicle’s general maximum only under specific conditions.
| Four-axle articulated vehicle | Maximum and conditions |
|---|---|
| Two-axle tractor and two-axle semi-trailer | 36 t generally |
| Driven axle with twin wheels and air or equivalent suspension; semi-trailer axle spacing above 1.80 m | 38 t; respect 18 t for the motor vehicle and 20 t for the towed tandem |
| Semi-trailer spacing at least 1.30 m but below 1.80 m; reinforced tipping body for construction, works or mining | 38 t; respect axle maxima and permissible coupling load |
Exam trap: Wrong: spacing of exactly 1.80 m qualifies for the wider-spacing exception. Right: you need more than 1.80 m, twin wheels and air or equivalent suspension on the driven axle. Respect 18 t for the motor vehicle and 20 t for the towed tandem.

Your articulated vehicle’s authorised mass includes the vehicles, people and goods.
| Articulated vehicle: tractor axles | Semi-trailer axles | General maximum |
|---|---|---|
| Two or more | Three or more | 44 t |
| Three | Two | 44 t |
Exam trap: Wrong: load 44 t of goods. Right: the 44 t includes the vehicles and people; you must also respect all other limits.

For a road train, you must count each unit’s axles.
| Road train: lorry axles | Trailer axles | General maximum |
|---|---|---|
| Two | Two | 36 t |
| Two | Three | 42 t |
| Three | Two or three | 44 t |
Exam trap: Wrong: every five-axle combination allows 44 t. Right: a road train with a two-axle lorry and three-axle trailer has a general maximum of 42 t.

You may apply mass increases only when you meet the exception’s conditions.
| Vehicle or combination in eligible legal-table rows | Possible increase |
|---|---|
| Alternative-fuel technology | Its extra weight, up to 1 t |
| Zero-emission technology | Its extra weight, up to 2 t |
| Vehicle intended for urban services | Up to 1 t beyond technology increases; respect technical and axle maxima |
| Combination in a legally defined intermodal operation | Up to 2 t |
Exam trap: Wrong: any container allows the intermodal increase. Right: meet the legal definition, using containers or swap bodies totalling up to 45 feet in the specified operations. For inland-waterway or maritime operations, the initial or final road leg within the Union must not exceed 150 km, except to reach the nearest suitable terminal in the specified configurations.

You may use roundwood maxima only for the specified wood and routes.
| Roundwood vehicle in eligible legal-table rows | Maximum on permitted routes |
|---|---|
| Three-axle motor vehicle | 32 t |
| Other four-axle rigid vehicles covered by the note | 42 t |
| Four-axle road train covered by the note | 42 t |
| Five-axle articulated vehicles and road trains covered by the note | 52 t |
| Articulated vehicles and road trains with six or more axles covered by the note | 57 t |
Exam trap: Wrong: apply these masses on any route. Right: use predetermined routes between neighbouring provinces or routes of at most 150 km between the forest and nearest forestry industry facility. You may go below 25 % on driven axles only if you can move off on 8 % gradients while respecting axle maxima.

You must check your laden width and your route’s restrictions.
| Vehicle or superstructure | Maximum width |
|---|---|
| Vehicle including load: general rule | 2.55 m |
| Fixed or mobile superstructure partly equipped for temperature-controlled goods; each side wall, including insulation, at least 45 mm thick | 2.60 m |
Exam trap: Wrong: any vehicle called refrigerated may be 2.60 m wide. Right: its superstructure must be partly equipped for temperature-controlled goods, with each side wall, including insulation, at least 45 mm thick.

You must measure laden height and check whether your vehicle qualifies for an exception.
| Vehicle or permitted transport | Maximum laden height |
|---|---|
| General rule | 4.00 m |
| Lorry or combination specialising in vehicle transport; recovery vehicle for crashed or broken-down vehicles | 4.50 m |
| Lorry or articulated vehicle carrying enclosed containers approved for combined, intermodal or ULD air transport | 4.50 m |
| Variable-height lorry or articulated vehicle for live animals, straw bales and fodder | 4.50 m |
| Supplies from suppliers to industrial facilities on predetermined routes shorter than 50 km | 4.50 m |
Exam trap: Wrong: permission for 4.50 m lets you use any bridge. Right: respect each road’s height limit and check actual clearance.

You must measure the whole combination and also respect semi-trailer measurements.
| Goods vehicle or semi-trailer measurement | Maximum length |
|---|---|
| Individual motor vehicle | 12.00 m |
| Individual trailer | 12.00 m |
| Whole articulated vehicle including load | 16.50 m |
| Kingpin axis to semi-trailer rear | 12.00 m |
| Horizontal distance from kingpin axis to any front point of the semi-trailer | 2.04 m |
Exam trap: Wrong: freely add three metres behind an articulated vehicle. Right: an ordinary 16.00 m articulated vehicle, without an exception or supplementary authorisation, has only 0.50 m available within the overall length limit for an indivisible load projecting only behind. You must also meet projection rules.

For a road train, you must check overall length and loading-area measurements.
| Road train | Maximum laden length |
|---|---|
| General rule | 18.75 m |
| Specialised car transporter, laden, with authorised rear support or overhang | 20.55 m |
Exam trap: Wrong: use 20.55 m with an empty car transporter. Right: you must be laden and use an authorised rear support or overhang. For rear load projection, the last axle of the carried vehicle must rest on the trailer structure.

You may exceed general length limits only in expressly permitted cases.
| Permitted case | Allowed excess |
|---|---|
| Intermodal operation with 45-foot containers or swap bodies, laden or empty | 15 cm for the specified measurements |
| Bars, beams, pipes or similar indivisible long items grouped together, exceeding only maximum length | 150 cm, while meeting all other conditions |
| Approved aerodynamic cabs or devices | Only for their purpose; no increase in load capacity |
Exam trap: Wrong: any long load allows another 150 cm. Right: it must be a group of indivisible longitudinal items of the specified types, exceeding only the maximum length dimension and meeting the note’s other conditions.

You must distinguish turning radii from the space your vehicle sweeps through.
| Vehicle or combination | Outer radius | Inner radius |
|---|---|---|
| General rule | 12.50 m | 5.30 m |
| Euromodular configuration | Up to 14.50 m | Up to 6.50 m |
Exam trap: Wrong: always apply 1.0 m outswing. Right: in the category N rigid vehicle test, the general maximum is 0.80 m; for category N vehicles with retractable or load-relieving axles raised, it is 1.0 m.

You may drive a euromodular combination only on approved routes.
Exam trap: Wrong: meeting 32 m and 72 t lets you choose any road. Right: use the route network set by the authority and meet its conditions.

You must include projecting loads when checking maximum dimensions.
Exam trap: Wrong: measure only your vehicle. Right: include any projecting load.

You need prior supplementary authorisation if your indivisible load exceeds maxima without an applicable exception.
| Case | What you must check |
|---|---|
| One indivisible load | Dividing it causes unnecessary cost or damage risk; it cannot fit within regulatory maxima |
| Several items of the same nature and purpose | No extra dimensions exceeded beyond those exceeded by the largest item; respect total and axle masses |
Exam trap: Wrong: group any overload as indivisible. Right: items must have the same nature and purpose, exceed no dimensions other than those exceeded by the largest item, and respect maximum total and axle masses.

For special transport, you must follow your authorisation and arrange the required escort.
| Group 1 special transport with indivisible load | Required condition |
|---|---|
| Width above 3 m or length above 20.55 m on autopistas or autovías | Escort behind, at least 50 m away |
| Width above 3 m or length above 20.55 m on other roads | Escort ahead |
| Conventional road, travelling below half its general speed limit | Another escort behind, at least 50 m away |
| Width above 5 m | You need an escort by officers. As the holder, give at least 72 hours’ notice before each journey to officers in the departure province and the body designated by the road authority. Give the departure place, time and date, registration numbers and a copy of the authorisation. |
| General authorisation | Maximum 70 km/h; respect stricter ITV limits |
| Specific authorisation | Maximum 60 km/h; respect stricter ITV limits |
| Exceptional authorisation | Authorised speed, never above 60 km/h; respect stricter ITV limits |
Exam trap: Wrong: the escort always keeps V-2 switched on. Right: use it according to the authorisation, visible from front and rear, and switch it off when the service ends.

You must compare mass signs with the relevant actual weight.
| Mass sign | What you compare |
|---|---|
| R-201 | Actual laden mass of vehicle or combination |
| R-202 | Mass transmitted to the ground by each axle |
Exam trap: Wrong: compare R-201 with the MMA in your documents. Right: compare actual laden mass; for R-202, check each axle.

You must respect signed dimensions even if your vehicle is allowed a higher maximum.
| Dimension sign | What you measure including load |
|---|---|
| R-203 | Overall vehicle or combination length |
| R-204 | Maximum width |
| R-205 | Maximum height |
Exam trap: Wrong: permission to reach 4.50 m lets you pass any height limit. Right: at 4.20 m, you cannot pass an R-205 showing 4.10 m.

If your lorry requires a speed limiter, you must keep it working and sealed.
| Lorry or tractor unit subject to the obligation | Registration dates covered |
|---|---|
| N3 | From 1 January 1988 |
| N2 | From 1 January 2005 |
| N2 meeting the regulation’s specified Euro 3 emission limits | Between 1 October 2001 and 1 January 2005 |
Exam trap: Wrong: every lorry has the same obligation without exceptions. Right: check category and registration date. Exemptions may apply if it cannot exceed 90 km/h by design, performs scientific road tests, provides only public service in urban areas, or is used by the security and emergency services listed in the regulation.
Cross-check the legal configuration against the documentation and actual mass distribution.
The projection must comply with both the load rules and the overall dimensions.
Compare the correct quantity with the figure on the sign.
Mark it as read and you will see your progress on the theory list.