Theory · C+E Licence - Articulated Truck · Module 6 of 13

Safety devices for the vehicle combination

You learn to recognise and check the devices that keep your C+E combination safe and visible, from the secondary coupling to its lights, number plates, mirrors and protective devices. You master the thresholds and emergency equipment covered in the exam, including wheel chocks, a connected V-16 beacon, a high-visibility vest and fire extinguishers.

32 min read25 sectionsReviewed Nov 3, 2026
A driver wearing a reflective vest checks a wheel chock beside a parked articulated truck with visible lights, reflectors and protective guards.
Articulated vehicle safety inspection

1Each device has its own function

A driver wearing a reflective vest inspects the illuminated rear lights of a semitrailer attached to a tractor unit and parked beside the kerb on its right side.
The key idea

Check each safety system separately, including the towed vehicle.

Remember

  • Check the coupling, brakes and lights separately.
  • Add a safe external check to the warnings you get in the cab.

Exam trap: Wrong: you check the tractor and assume the trailer is checked. Right: check the towed vehicle too.

Read the full explanation
  • The mechanical coupling keeps the combination together, automatic braking stops the towed vehicle if it separates, and the lights allow others to see it. The mechanical coupling, automatic braking and lights are related systems, but each must work independently; a chain or an illuminated light does not prove that the rest is in order. [RGV, art. 12](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12). [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • In your lorry and trailer or tractor unit and semi-trailer combination, you must also check the towed vehicle. You may receive warnings or see some devices from the cab, but you must supplement this information with an exterior inspection in safe conditions. Having the towing vehicle’s lights in working order does not prove that the trailer’s lights work.

2Secondary safety coupling

Close-up of a trailer attached to a vehicle by a hitch and short safety chains crossed beneath the drawbar, beside a road carrying an articulated lorry.
The key idea

You need a secondary coupling when your trailer meets the mass and braking conditions.

1,500 kgMaximum MMA

Remember

  • Check the maximum authorised mass, called MMA.
  • Up to this limit, you need a secondary coupling if breakaway braking is absent.
  • If the main coupling fails, stop the drawbar touching the ground.
  • It must also retain some trailer guidance.
  • Do not continue with a broken main coupling.

Exam trap: Wrong: every heavy semi-trailer needs a chain. Right: a trailer up to 1,500 kg MMA needs a secondary coupling if breakaway braking is absent.

Read the full explanation
  • If you tow a trailer with an MMA (maximum authorised mass) not exceeding 1,500 kg without a system that ensures braking if the coupling breaks, it must have a secondary coupling in addition to the main one. The regulations allow a chain, cable or other device that performs the required function; the material alone does not identify its purpose. [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • If the main coupling separates, this secondary coupling must prevent the drawbar from touching the ground and retain some residual steering control of the trailer. [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • You must not confuse the safety chain with an anti-theft device, an electrical earth connection or a repair to the main locking mechanism. It performs its function when the main coupling fails, so you must check that its anchorage points and routing are suitable for the system fitted.
  • The 1,500 kg limit refers to the trailer’s MMA and applies in conjunction with the absence of the breakaway braking described above. For a heavy C+E combination, you must not answer that every semi-trailer necessarily needs a chain of this type: you must identify the appropriate safety arrangement. [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).

3Breakaway cable and automatic braking

A worker inspects the pneumatic connections of a parked articulated lorry, with the semitrailer resting on the fifth wheel.
The key idea

Check that automatic braking stops the towed vehicle if it separates while driving.

Trailer or semi-trailer systemWhat to check
Breakaway cable, if fittedAttachment and route specified by maker
Heavy combination emergency brakingSystem fitted; do not copy small trailer setup

Remember

  • If fitted, attach the breakaway cable where the maker says.
  • Follow its route to prevent pulls or braking during normal manoeuvres.
  • Identify the emergency system fitted to your heavy combination.
  • Check accessible cables, chains, hooks and fastenings before driving.
  • Never test it by separating the moving combination.

Exam trap: Wrong: fit a small trailer’s cable to every semi-trailer. Right: identify the emergency system for the equipment fitted.

Read the full explanation
  • The automatic braking devices on the trailer or semi-trailer must ensure that it stops automatically if it becomes uncoupled or the coupling breaks while driving. This system applies the brakes if the towed vehicle separates. [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • If the equipment uses a breakaway cable that applies the brake on separation, you must attach it to the designated point and follow the routing specified by its manufacturer. The cable must be able to perform its function without coming loose or applying the brake during a normal manoeuvre.
  • For heavy combinations, identify the emergency system specific to the braking equipment fitted. You must not automatically apply the cable arrangement used on a small trailer to a semi-trailer with pneumatic connections. Braking and its circuits are covered in detail in the “Trailer and vehicle combination braking” module. [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12). [RGV, art. 13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Visually check the condition of accessible cables, chains, hooks and fastenings, looking for breaks, deformation or incorrect fitting. As a safety guideline, rectify any fault before driving and follow the system manual; do not test its operation by causing the combination to separate while moving.

4Connections and safety locks before driving

A driver wearing a reflective vest inspects the coupling of a parked articulated truck, with the air and electrical connections attached between the tractor unit and the semitrailer.
The key idea

Before driving, check that the coupling and connections are compatible and secure.

Remember

  • Check that mechanical, air and electrical connections are compatible.
  • Check the coupling lock and safety devices before moving or restarting.
  • Allow movement without dragging, pulling or trapping connections.
  • Raise and secure the semi-trailer supports before moving.
  • Before uncoupling, secure the towed vehicle and support the semi-trailer.

Exam trap: Wrong: being able to join the parts is enough. Right: check that they are compatible and secured.

Read the full explanation
  • The mechanical, pneumatic and electrical components between the towing vehicle and trailer must be compatible. You must check that each connection is correctly coupled and secured; being able to physically join two parts is not enough to prove their technical compatibility. [RGV, art. 13.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Before moving off or resuming your journey, check that the main coupling is closed, locked and secured as required for that model. Then check its connections and auxiliary devices.
  • Allow the connections enough movement for the combination to articulate, while preventing them from dragging, becoming trapped or being placed under undue tension. Also check that the semi-trailer’s landing legs are retracted and secured before moving.
  • Before uncoupling the towed vehicle, you must secure it against movement and, if it is a semi-trailer, leave it properly supported on its landing legs. The full coupling and uncoupling sequence is covered in “Safe coupling and uncoupling”; here you must recognise that the parking brake, wheel chocks and supports perform different functions. [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).

5Position lights and number plate lighting

An articulated truck travels in the right-hand lane at dusk, with the semitrailer’s two red rear position lights switched on and a white lamp illuminating the rear licence plate.
The key idea

Check the towed vehicle’s position lights and rear number plate lighting.

1.60 mFront light width limit
Non-agricultural towed vehicle widthFront position lights
More than 1.60 mMandatory
1.60 m or lessOptional

Remember

  • Check the two red rear position lights on your non-agricultural towed vehicle.
  • Check the two white front lights when required.
  • Keep the rear plate and its white light visible.
  • Use position lights at night, in greatly reduced visibility, tunnels and underpasses.
  • The tractor’s daytime lights do not guarantee trailer lighting.

Exam trap: Wrong: front position lights are required at exactly 1.60 m. Right: they are required above that width.

Read the full explanation
  • Your non-agricultural trailer or semi-trailer must have two red rear position lights. You must check that they are visible from behind and indicate the vehicle’s presence and width. It is not enough for the lorry’s lights to be visible if the towed body obscures them. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The towed vehicle has two white front position lights; these are compulsory when its width exceeds 1.60 m and optional when its width is equal to or below this figure. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The towed vehicle must have white lighting for its rear number plate. You must check that it allows the plate to be identified without being obscured by mud, open doors, brackets or accessories. The number plate and the light illuminating it are separate components, and both must retain their function. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • When driving at night, in significantly reduced visibility or through tunnels and underpasses, you must keep the combination’s required position lights on. The rear number plate must be illuminated in the circumstances specified by the regulations; the towing vehicle’s daytime running lights alone do not prove that all this lighting is on. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99). [RGC, art. 103](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a103).

6Brake lights, indicators and hazard warning lights

A person wearing a reflective vest observes from one side the two illuminated rear hazard lights of an articulated truck immobilized with a wheel chock in a paved area.
The key idea

Check the towed vehicle’s indicators, hazard warning lights and brake lights separately.

Non-agricultural trailer lightsColour and purpose
IndicatorsAmber: signal your manoeuvre
Hazard warning lightsUse the same indicators
Brake lightsRed: show that you are braking

Remember

  • Check the amber rear indicators on your non-agricultural trailer.
  • They must be fitted in an even number.
  • Check hazard warning lights on both vehicles.
  • Apply the brake to check both red brake lights.
  • Keep the combination stationary during checks.
  • Keep helpers outside danger areas.

Exam trap: Wrong: working position lights prove the brake lights work. Right: operate and check each function.

Read the full explanation
  • Your non-agricultural trailer must have an even number of amber rear direction indicators. You must check both sides: a fault on one side may leave you unable to signal precisely the manoeuvre you need to make when joining traffic or changing course. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The hazard warning signal uses the direction indicators, with the same colour and arrangement. You must check that they work on both the towed vehicle and the towing vehicle; operating the hazard warning switch does not prove that the lamps at the rear of the combination receive power. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The towed vehicle has two red brake lights, as specified in the general table in Annex X. You must check their response when you apply the brake, distinguishing them from the position lights: they share the same colour but indicate different situations, and you cannot consider one function checked by looking only at the other. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • For a practical check, use someone observing from a safe place or a method that allows you to verify each function properly. Do not position anyone between the vehicles or behind a combination that could move. You must carry out the check with the vehicle immobilised and the controls operated in a controlled manner.

7End-outline marker lamps: recognising the width

An articulated truck travels in the right lane of a road with two red clearance lights illuminated at the upper rear corners of its semitrailer and amber side marker lights.
The key idea

You need end-outline marker lamps when your towed vehicle exceeds the width limit.

2.10 mWidth limit
Trailer or semi-trailer widthRequirement based on width
More than 2.10 mEnd-outline marker lamps required
Exactly 2.10 mDoes not exceed the threshold

Remember

  • Above this width, check your end-outline marker lamps.
  • Check two white lamps at the front and two red lamps behind.
  • Check high points for hidden, missing or damaged lamps.
  • Use them with position lights at night and in greatly reduced visibility.
  • Also use them in tunnels, underpasses and signed tunnel sections, even by day.

Exam trap: Wrong: end-outline marker lamps are required at exactly 2.10 m. Right: the rule applies above that width.

Read the full explanation
  • If your trailer or semi-trailer is more than 2.10 m wide, it must have end-outline marker lamps. You must associate these with width, rather than mass or the need for a C+E licence. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • End-outline marker lamps are white at the front and red at the rear, with two front and two rear lamps in the equipment specified for trailers. Their position allows others to recognise the upper extremities of the vehicle. You must not confuse them with amber side marker lights. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must switch on the required end-outline marker lamps together with the position lights between sunset and sunrise, when visibility is significantly reduced and when driving through tunnels, underpasses or sections signposted as tunnels. This requirement also applies when you pass through during the day. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99).
  • During your exterior inspection, look at the high points of the towed vehicle and check that no lamps are missing, obscured or damaged. On a tall box body, checking only the lower light clusters leaves unchecked the very devices that help others judge its size.

8Side marker lights on the trailer

An articulated lorry travels to the right along a road with amber side-marker lights illuminated along its semitrailer.
The key idea

Link side lights to length, and check the side reflectors too.

6 mLength threshold
Non-agricultural trailer side equipmentRequirement
Side position lightsRequired if longer than 6 m
Non-triangular reflectorsRequired without that length condition

Remember

  • Your non-agricultural towed vehicle needs side lights above this length.
  • Check that these lights are amber.
  • Check side reflectors even if your trailer does not exceed this length.
  • Walk along both sides and clear anything hiding lights or reflectors.

Exam trap: Wrong: side reflectors are required only above 6 m. Right: that limit applies to side lights.

Read the full explanation
  • Side marker lights are compulsory on non-agricultural trailers and semi-trailers more than 6 m long. Therefore, in an exam question involving a 7 m semi-trailer, you must answer that they are compulsory; you must check the length of the towed vehicle when applying this condition. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • They are amber, and their number depends on the length of the towed vehicle under the installation requirements. These lights show the presence of the towed vehicle from the side, especially when your combination crosses another road user’s path or manoeuvres in poor lighting. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Non-triangular side retroreflectors are compulsory on non-agricultural trailers; article 16.5 does not make them subject to the 6 m threshold. You must avoid applying the length requirement for side marker lights to all reflective devices along the sides. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16).
  • As an inspection routine, walk along both sides: a check from behind can miss side lights and reflectors. Make sure that toolboxes, tarpaulins, dirt or repairs do not obscure them.

9Fog lamps and reversing lights

An articulated truck travels in the right lane of a road in thick fog with one red rear fog lamp illuminated on its semitrailer.
The key idea

Use rear fog lights only in very bad conditions, and check reversing lights.

Non-agricultural trailer equipmentColourProvision
Rear fog lightsRedOne or two; mandatory
Reversing lightsWhiteOne or two; generally optional, subject to type approval

Remember

  • Check the red rear fog light on your non-agricultural trailer.
  • Use it in thick fog, very heavy rain or heavy snow.
  • Also use it in dense clouds of dust or smoke.
  • Do not remove reversing lights required by type approval.
  • Even with reversing lights on, check mirrors and blind spots.

Exam trap: Wrong: use rear fog lights just because it is night. Right: use them only in particularly bad conditions.

Read the full explanation
  • Your non-agricultural trailer must have a red rear fog lamp; the table in Annex X specifies one or two. You must check this function specifically, because the position lights or brake lights coming on does not establish that the fog lamp is present and works. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • You must only switch on the rear fog lamp in particularly adverse weather or environmental conditions, such as thick fog, very heavy rain, heavy snowfall or dense clouds of dust or smoke. [RGC, art. 106.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106).
  • The general table in Annex X lists one or two white reversing lights as optional equipment for trailers. You must interpret this table alongside the technical type-approval requirements applicable to the specific vehicle; you must not remove or disable equipment that is required or installed on your semi-trailer. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • If your combination has reversing lights, you must check that they indicate this manoeuvre and cannot be confused with a red braking signal. Switching them on helps warn others of the movement, but does not prove that the area is clear or replace looking in your mirrors and checking blind spots. [RGC, art. 109.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109).

10Retroreflectors: shape and colour

An articulated lorry travels in the right lane of a road, with two red triangular retroreflectors on the rear of its semitrailer and yellow rectangular reflectors along its side.
The key idea

Recognise your towed vehicle’s reflectors by position, shape and colour.

Towed vehicle reflectorsShapeColour
FrontNon-triangularWhite
RearTriangularRed
SideNon-triangularAmber, except where grouped with rear signalling devices

Remember

  • Check the two required red triangular rear reflectors.
  • Do not replace them with rectangles, even red ones.
  • Keep every reflector clean and intact.
  • They reflect received light; they do not produce light.
  • Do not use them instead of required lights.

Exam trap: Wrong: replace rear triangles with red rectangles. Right: keep the required triangular shape.

Read the full explanation
  • Your trailer or semi-trailer must have two red triangular rear retroreflectors, a feature that identifies the towed vehicle. You must retain this prescribed shape and colour when replacing a damaged part. [RGV, art. 16.5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16). [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Your towed vehicle has two front retroreflectors, which are white and non-triangular. These devices reflect the light that reaches them and do not depend on you connecting or switching on the lighting circuit. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • The side retroreflectors are non-triangular and amber, with the colour exception provided for those grouped with rear signalling devices. You must first learn the basic arrangement: white at the front, red at the rear and amber along the sides. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • A retroreflector does not produce the light that makes it visible. You must therefore keep it clean and intact even when the entire electrical system works. Likewise, reflectors do not replace compulsory lights or allow you to drive with an unresolved connection fault.

11Checking lighting and visibility

A person wearing a reflective vest checks and cleans the rear lights of an articulated truck stopped beside the right edge of the road, with its two red lights illuminated and symmetrical.
The key idea

Check every lighting function and adjust your driving if a fault occurs.

Remember

  • Check each function separately, including lights required for your combination.
  • Keep windows, mirrors, lights and reflectors clean.
  • Keep matching lights equal in colour and intensity, and symmetrically placed.
  • Before driving, fix faults that stop you signalling your presence or manoeuvres.
  • If an unrepairable fault reduces lighting, slow down.
  • You must be able to stop within the lit area.

Exam trap: Wrong: any working light lets you continue. Right: assess the fault and arrange repair or assistance.

Read the full explanation
  • Paired devices with the same purpose must match in colour and intensity and be positioned symmetrically as prescribed by the regulations. You must avoid improvised repairs that change the colour or leave a signal that is difficult to interpret; a lamp that emits light does not necessarily fulfil its prescribed function. [RGV, art. 15.1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15).
  • Check the position lights, number plate lights, indicators on each side, hazard warning lights, brake lights, end-outline marker lamps and side marker lights in turn, where applicable, as well as the other functions fitted. An orderly inspection prevents you from mistaking an illuminated light cluster for a check of every function it incorporates.
  • Keep windows, mirrors, lights and reflectors clean so that you can see and be seen. Interior cab lighting does not replace exterior lighting. As a safety practice, if you detect a fault that prevents you from correctly signalling the presence or manoeuvres of your combination, resolve it before starting your journey.
  • If a fault that cannot be repaired during the journey forces you to drive with reduced lighting intensity, you must reduce your speed so that you can stop within the illuminated area. This rule does not mean that any loss of trailer signalling authorises you to continue: assess the fault and arrange the necessary repair or assistance. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107).

12Two number plates at the rear

Rear view of an articulated lorry in the right lane of a rural road, with a blank red plate centered on the semitrailer and a white plate to its right.
The key idea

Above the MMA limit, your towed vehicle needs its own plate and the tractor’s.

750 kgMMA threshold
Rear plate on a towed vehicle above 750 kg MMAPosition or appearance
Towed vehicle’s own plateCentred, vertical or nearly vertical; red background and black characters
Tractor unit’s registrationOn the right; must match the current tractor unit

Remember

  • Above this limit, check both rear number plates.
  • Keep plates clean, secure and clear.
  • If you change tractor units, check the copied registration matches.

Exam trap: Wrong: one rear plate is enough above 750 kg MMA. Right: carry the towed vehicle’s plate and the tractor’s registration.

Read the full explanation
  • If your trailer or semi-trailer has an MMA (maximum authorised mass) above 750 kg, it must display its own number plate at the rear and another bearing the registration number of the towing vehicle. In your C+E combination, you must recognise both identifiers: one belongs to the towed vehicle and the other to the tractor unit pulling it. [RGV, Annex XVIII, section III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • Your towed vehicle’s own number plate must be vertical or nearly vertical and in its median longitudinal plane. You place the plate bearing the tractor unit’s registration number on the right-hand side. You must pay attention to the location and must not answer that any arrangement is sufficient as long as there are two plates. [RGV, Annex XVIII, section III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • The standard number plate for trailers and semi-trailers has a red background and black characters. The standard plate belonging to your tractor unit carries its own prescribed identification; you must avoid confusing the red of the trailer’s number plate with a danger or load sign. [RGV, Annex XVIII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).
  • If you change the tractor unit pulling the same towed vehicle, check the plate bearing the towing vehicle’s registration number: it must match the vehicle forming the combination. As an inspection routine, also check that the plates are secure and clean and that nothing obscures the characters before you set off. [RGV, Annex XVIII, section III.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii).

13Rear long-vehicle plate

An articulated truck travels in the right lane of a rural road, viewed from behind, with a centered yellow V-6 plate with a red border and two red upper rear lights.
The key idea

Use V-6 when your vehicle or complete combination exceeds the length limit.

12 mLength limit
500 mmMinimum fitting height
1,500 mmMaximum fitting height
Vehicle or complete combination lengthV-6 requirement by length
More than 12 mMandatory
Exactly 12 mDoes not exceed the threshold

Remember

  • Measure the whole combination to decide if you need V-6.
  • Fit the approved sign at the rear, centred.
  • You may use two matching plates, symmetrical and near the edges.
  • Keep within the fitting height limits.
  • The sign uses yellow reflective and red fluorescent material.
  • Do not confuse it with number plates or load warning panels.

Exam trap: Wrong: V-6 is required at exactly 12 m. Right: you need it above 12 m, counting the whole combination.

Read the full explanation
  • The V-6 sign, Long vehicle, indicates that the vehicle or combination exceeds 12 m in length. You must consider the whole combination: you may need it even if each individual unit is shorter. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • You must fit it at the rear, centred on the vehicle's centreline. Where fitting requirements make it appropriate, you may use two equivalent plates positioned symmetrically on either side of the centreline and as close to the edges as possible. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • You must fit it at a height of between 500 and 1,500 mm above the ground. The sign has yellow reflective and red fluorescent material and must be type-approved. Its purpose is to warn anyone approaching from behind of the combination's length. [RGV, Annex XI, V-6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-6).
  • Distinguish the V-6 from number plates, the trailer's triangular reflectors and the marker panel for a projecting load. Each item has its own purpose and requirement; carrying one does not exempt you from carrying the others that apply. Load marking is covered in «Safe, well-distributed loads».

14Reflective contour markings

A person wearing a high visibility vest inspects the red rear and yellow side contour markings of an articulated lorry parked beside the right-hand kerb, with separate lamps and triangular reflectors.
The key idea

Keep the reflective marking required for your vehicle and check its condition.

Remember

  • Recognise V-23 strips as reflective marking.
  • The requirement depends on maximum masses, lengths and vehicle categories.
  • Use approved material fitted as required.
  • Check that repairs, mud or damage have not left strips incomplete.
  • Check your lights too: reflective strips do not replace them.

Exam trap: Wrong: any decorative strip meets the rule. Right: keep the approved marking required for your vehicle.

Read the full explanation
  • The V-23 sign, Goods vehicle marking, consists of reflective markings that make the vehicle or combination more visible and recognisable. The strips outline the vehicle by reflecting the light they receive and supplement the marking of its extremities. [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23).
  • Whether you need rear and side markings depends on maximum masses, lengths and categories under UNECE Regulation 48, to which the Reglamento General de Vehículos (General Vehicle Regulations) refers. You must not assume that every small trailer needs a full contour marking or that any decorative strip meets the requirement. [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23).
  • The material must be type-approved under UNECE Regulation 104 and its installation must meet the specified technical conditions. As the driver, you must maintain the arrangement required for your vehicle and check that repairs to the bodywork or tarpaulins have not left it incomplete. [RGV, Annex XI, V-23](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-23).
  • As a practical guideline, inspect the strips from different angles during your exterior walk-round. A strip covered in mud or damaged becomes less useful even if it is still attached to the vehicle. You must also check the lights: reflective markings help others judge the vehicle's overall size and do not replace the lights' electrical power supply.

15Mirrors on the towing lorry

An articulated truck stopped beside the right-hand kerb shows the exterior mirrors on both sides of the cab and the driver seated at the wheel.
The key idea

Check your lorry’s required mirrors and adjust them while the combination is stationary.

7.5 tThreshold for some mirrors
2 mHeight reference
Lorry mirrorVehicles coveredPurpose or condition
Class IIN2 and N3Main exterior mirrors: left and right
Class IVN3 and N2 above 7.5 tWide-angle; subject to installation conditions
Class VN3 and N2 above 7.5 tClose-proximity: above 2 m fully laden, including adjustments and attachments
Class VIN3 and N2 above 7.5 tFront: at least 2 m at technically permissible maximum mass; subject to type approval

Remember

  • N2 and N3 lorries need main exterior mirrors on both sides.
  • An interior mirror does not replace these exterior mirrors.
  • Sit correctly, then adjust mirrors while stationary.
  • Keep mirror glass clean and supports secure.
  • Follow fitting and approval conditions for each mirror class.

Exam trap: Wrong: close-proximity and front mirrors have the same height rule. Right: close-proximity mirrors must be above 2 m, including adjustment points and attachments, fully laden. Front mirrors must be at least 2 m at maximum technically permissible mass. These rules apply in every adjustment position. If a condition cannot be met, fitting is prohibited.

Read the full explanation
  • For categories N2 and N3, you must have two class II main exterior mirrors, one on the left and one on the right. You must apply the rule for lorries: having an interior mirror does not replace these compulsory exterior mirrors. [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • Class IV is the wide-angle mirror and class V is the close-proximity mirror. The table in Annex III requires them on N3 vehicles and N2 vehicles over 7.5 t, subject to the specified installation conditions. You must maintain the type-approved equipment required for your vehicle: the wide-angle mirror extends your view to the side and the close-proximity mirror shows the area close to the cab. [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • The class VI front mirror lets you see the area immediately in front of the cab; you must have one on N3 vehicles and N2 vehicles over 7.5 t in accordance with the applicable type approval. It must be at least 2 m above the ground in all adjustment positions, with the vehicle at its maximum technically permissible mass; if the cab height prevents this condition from being met, its installation is prohibited. [UN Regulation No. 46, paragraphs 15.2.1.1.1, 15.2.2.7 and 15.2.4.6](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-81759).
  • Class V close-proximity mirrors must be more than 2 m above the ground in all adjustment positions, including adjustment points and attachments, with the vehicle fully laden. If this condition cannot be met, their installation is prohibited under Annex III. [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • You must adjust the mirrors with the combination stationary, after positioning yourself correctly in the seat. Check both sides and the nearby areas, keep the mirror glass clean and check that the mountings do not vibrate or move out of position. Poor adjustment reduces the information available to you even in daylight.

16Extension mirrors and blind spots

An articulated truck is stopped beside the right-hand kerb, with the driver on the left of the cab and an extended mirror reflecting the side of the semitrailer and the adjacent space.
The key idea

Adapt your view to the coupled trailer and watch areas your mirrors cannot show.

Remember

  • Check your field of vision with the trailer coupled.
  • If you cannot see enough, use a suitable permitted solution.
  • Secure extra mirrors and check their direction.
  • Remember that your view changes as the combination turns.
  • If you lose a needed reference, stop and check safely.

Exam trap: Wrong: towing always means fitting extension mirrors. Right: use them when needed for the required field of vision.

Read the full explanation
  • If the towed vehicle obstructs the necessary field of vision, you must use a suitable means of indirect vision that meets the vehicle's technical requirements. Extension or supplementary mirrors may provide the necessary view; you must not fit them on the basis of an automatic rule simply because you are towing a trailer. [RGV, art. 11.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11). [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii).
  • As an adjustment guideline, check the field of vision with the trailer actually coupled. An adjustment that works when driving the towing vehicle alone may be inadequate with a wider body or one in a different position. Secure supplementary mirrors so that they stay correctly aligned and do not create dangerous projections.
  • The mirrors help you monitor the sides, the towed vehicle and the nearby space, but you must know which areas they do not show. As the combination articulates, the view in each mirror changes; do not assume that a road user has left the danger zone because they have disappeared from the mirror.
  • If you lose a reference point you need for manoeuvring, stop and check your surroundings safely. You must keep observing continuously: dirt reduces visibility, incorrect adjustment leaves areas uncovered and a loose mounting can change the view during the manoeuvre.

17Wheel chocks on a pronounced slope

An articulated lorry is parked on a downhill slope beside the kerb on its right, with orange wheel chocks against the downhill sides of two tyres.
The key idea

Choose suitable wheel chocks and position them to stop your combination moving.

Your combination’s situationHow to secure it
Leaving the driving position on a pronounced slopeSuitable chocks or a steered wheel against the kerb as prescribed
Trailer or semi-trailer to be uncoupledChock wheels on its own axles following instructions
Possible movement in both directionsProvide protection in both directions following instructions

Remember

  • A wheel chock is a wedge that stops a wheel rolling.
  • Choose chocks suitable for your combination’s wheels and mass.
  • When leaving your cab on a pronounced slope, secure your combination against movement.
  • Follow instructions to choose wheels, axles and which side to chock.
  • Place each chock firmly against the tyre; stay outside the wheels’ path.
  • Check shape, cracks and cleanliness; secure chocks in their holders.

Exam trap: Wrong: choose any wedge and place it without checking. Right: choose chocks suitable for your combination’s wheels and mass; follow the placement instructions.

Read the full explanation
  • A wheel chock is a purpose-made wedge that prevents a wheel from rolling by resting against it: its base rests on the ground and its contact face bears against the tyre. When choosing equipment, select a model whose manufacturer states that it is suitable for the wheel size and mass of the combination you intend to immobilise; check its instructions for use and capacity.
  • When you leave the driving position after stopping or parking your combination on a pronounced slope, you must secure it properly with purpose-made wheel chocks or by resting a steered wheel against the kerb as prescribed by the regulations; the other measures are covered in «Manoeuvres with goods vehicle combinations», in the section «Securing your combination when leaving the driving position». [RGC, art. 92.3.d](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a92).
  • As a placement guideline, follow the vehicle and chock instructions to choose the wheels and axles: on the towing vehicle, use the wheels on the specified axle and, if the trailer or semi-trailer is to be uncoupled, place chocks against the wheels on its own axles. Position each wedge firmly against the tyre tread, on the side towards which the unit could move; if you need to prevent movement in both directions, provide the corresponding protection in accordance with those instructions. Work from a safe position, outside the path of the wheels.
  • When inspecting the equipment, check that the chocks retain their shape, have no cracks and have clean base and contact surfaces. A deformed wedge or one with dirt that encourages slipping may lose effectiveness. Store them in their designated holders, secured so that they cannot fall off while driving and accessible for use; also check the closures and fastenings of these holders.

18Parking brake and supports

A detached semitrailer rests on its landing legs in a level yard, with wheel chocks and its parking brake knob pulled out, while the tractor unit stands separately ahead.
The key idea

Apply the towed vehicle’s parking brake and check its supports before uncoupling.

Trailer or semi-trailer equipmentPurpose
Parking brakeKeeps the towed vehicle stationary, including when uncoupled
Semi-trailer supportsHold up its front end; do not replace the brake

Remember

  • Before uncoupling, apply the towed vehicle’s parking brake using its own control.
  • Check that it stays still before releasing the coupling.
  • Keep its brake applied during separation and while the towed vehicle remains parked.
  • Check the landing legs are stable; they do not replace the brake.
  • Before driving, check coupling, connections and raised, secured supports.
  • Remove chocks once the combination is secure.

Exam trap: Wrong: landing legs replace the semi-trailer’s brake. Right: secure its support and prevent movement separately.

Read the full explanation
  • Before uncoupling, apply the trailer or semi-trailer's parking brake using its own control and check that it holds the unit stationary before releasing the coupling. For the other measures when leaving the driving position, see «Manoeuvres with goods vehicle combinations», in the section «Securing your combination when leaving the driving position». [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • The trailer or semi-trailer's parking brake keeps it stationary even when uncoupled. You must keep it applied while separating it from the towing vehicle and while the towed vehicle remains parked. [RGV, art. 12.8](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12).
  • The semi-trailer's supports hold up its front end when required, but do not replace the brake or the necessary means of preventing movement. As a safety guideline, check that the support is stable before pulling the towing vehicle away and keep people out of areas where the semi-trailer could fall or move.
  • Before driving again, check that the coupling is secured, the connections are in place and the supports are retracted and secured; remove the chocks once the combination is secured.

19Rear underrun protection

An articulated truck travels in the right lane of a road, with the semitrailer’s rear underrun protection bar highlighted in green and secured by two brackets.
The key idea

Check rear underrun protection and follow your vehicle’s technical requirements.

Vehicle or caseRear protection
N2, N3, O3 and O4Dimensions and strength follow applicable technical rules
Tractor units for semi-trailersExempt under the annex
Certain trailers for unprocessed timber or very long itemsSpecific exemptions
Protection incompatible with vehicle useThis must be recorded in the vehicle documents

Remember

  • Check the rear bar or structure and its attachments.
  • Check that it is not bent, loose or disabled.
  • If it moves for work, position it correctly before driving.
  • Do not apply one height to every heavy semi-trailer.
  • Do not extend the tractor unit’s exemption to an ordinary semi-trailer.

Exam trap: Wrong: apply 550 mm to every heavy semi-trailer. Right: follow its specific technical requirements.

Read the full explanation
  • Vehicles, including trailers and semi-trailers, must provide effective rear protection against other vehicles running underneath them. This can be achieved through a dedicated device or through the shape and structural strength of the rear of the vehicle. You must maintain its structure and mountings so that it can withstand the impact it is designed for. [RGV, art. 11.16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11). [RGV, Annex IV](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniv).
  • For heavy vehicles in categories N2, N3, O3 and O4, you must apply the dimensional and deformation resistance requirements in their technical regulations. You must not simply apply to them the alternative 550 mm condition that Annex IV provides for other categories: this is not a universal height for every semi-trailer. [RGV, Annex IV](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniv).
  • Annex IV provides exemptions, including tractor units for semi-trailers and certain trailers for unprocessed timber or very long items. It also covers vehicles on which the protection is incompatible with their use, a circumstance which must be recorded in their documentation. You must not extend the tractor unit exemption to an ordinary semi-trailer. [RGV, Annex IV](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniv).
  • As a checking guideline, inspect the bar or structure for deformation, detachment or damaged anchorage points. If a device can be moved for work purposes, follow the instructions to leave it in its position for road use.

20Side and front protection

An articulated truck parked beside the right-hand kerb shows the semitrailer’s side protection rails and the tractor unit’s front underrun protection in green.
The key idea

Keep the side and front protection required for your goods vehicle.

Goods vehicle protection, where requiredArea
Side protectionSides, including on trailers and semi-trailers
Front underrun protectionFront of the powered unit

Remember

  • Check side protection when technical rules require it.
  • Check for gaps, damage and loose attachments.
  • Do not remove it to gain space.
  • Also check required front protection on the powered unit.
  • Check approval and documents to identify required equipment.
  • Report missing, damaged or wrongly placed equipment for repair.

Exam trap: Wrong: a toolbox alone replaces side protection. Right: keep the required regulation-compliant protection.

Read the full explanation
  • Goods vehicles, including trailers and semi-trailers, must have side protection where their technical regulations require it. This protection fills the exposed space along the side between the wheels; you must maintain it, including its anchorage points and structural components. [RGV, art. 11.17](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).
  • Side protection helps prevent a road user from ending up under the vehicle in a side collision. As a safety guideline, check its continuity, condition and attachment. You must not remove it to gain space or assume that a toolbox fitted along the side is, on its own, a substitute for regulation-compliant protection.
  • Goods vehicles must also have front underrun protection where the applicable regulations require it. You must associate it with the front of the powered vehicle, distinguishing it from the rear protection on the towed vehicle and the protection along the sides. [RGV, art. 11.18](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).
  • To know exactly which equipment you must maintain on your combination, you must refer to its type approval, configuration and technical documentation. Your inspection as a driver consists of detecting missing, damaged or incorrectly positioned equipment and reporting it so that it can be put right; it does not replace strength requirements with a visual assessment.

21Connected V-16 beacon and mandatory equipment

An articulated lorry is stopped on the right shoulder with an illuminated yellow V-16 beacon on the cab roof, a connectivity symbol above it and its hazard lights on.
The key idea

Carry a certified connected V-16 in your non-special combination and keep it accessible.

Remember

  • Your Spanish-registered non-special combination must carry a valid connected V-16.
  • Triangles and unconnected beacons are not the regulatory warning device.
  • Check the make and model on the DGT official list.
  • Check when the connectivity service expires.
  • Keep it accessible from the cab and maintain its power supply.

Exam trap: Wrong: a commercial approval label is enough. Right: check the certified model and that its connectivity is valid.

Read the full explanation
  • You must carry a valid connected V-16 beacon in your non-special vehicle combination. For a vehicle registered in Spain, the required advance hazard warning device is the connected beacon; warning triangles and beacons without connectivity do not fulfil this regulatory function on the road. [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii). [DGT, V-16 devices](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).
  • You must check that the make and model appear on the official list of certified devices published by the DGT. A commercial label saying type-approved or a similar appearance to another beacon is not enough. Also check the expiry date of the connectivity service shown on the device. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • Keep the beacon somewhere accessible from the cab and maintain its power supply in accordance with the instructions. You must be able to use it when your vehicle becomes immobilised, without having to search among the load or walk along the arcén (hard shoulder) to a distant compartment. [DGT, V-16 devices](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).

22What the beacon must do

An articulated truck is stopped on the right shoulder of a road, with an illuminated V-16 beacon on the cab emitting light around it.
The key idea

Your beacon must make you visible and send your location without an app.

360 degreesHorizontal light coverage
30 minutesMinimum light intensity duration
100 secondsLocation update interval
12 yearsMinimum communications period

Remember

  • Your beacon reports activation, deactivation and location.
  • No external mobile app is needed.
  • Check that your beacon emits amber light.
  • Request assistance when needed: the transmission does not replace your call.

Exam trap: Wrong: you need to pair your phone for the V-16 to communicate. Right: it works without an external mobile app.

Read the full explanation
  • The V-16 emits amber light over a horizontal field of 360 degrees and must maintain the regulatory intensity for at least 30 minutes. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The beacon communicates its activation, deactivation and location to the national access point for traffic and mobility. Location information is sent every 100 seconds and stops after deactivation is communicated. You must distinguish this communication from any call you may need to make to request assistance. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The cost of communications must be included in the price and guaranteed for at least 12 years. The operating and communication components must be inside the casing, without depending on an external mobile app. [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).
  • The V-16 is intended to make a vehicle involved in an accident visible and transmit its location, with no additional functions. Calling the emergency services is covered in «Responding to accidents and breakdowns», section «Calling 112 with useful information». [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16).

23Placing the V-16 on a lorry

An articulated truck stopped on the right shoulder has an illuminated V-16 beacon resting on the cab roof, with the driver seated on the left side.
The key idea

Place your V-16 securely and with the greatest possible visibility.

Remember

  • Place your beacon securely and where it is as visible as possible.
  • If the body is higher than the cab, see
  • “Placing the beacon on a high cab”.
  • For lights, see “Hazard warning lights, position lights and end-outline marker lamps”.
  • To decide whether to leave, see “High-visibility vest and leaving the cab”.
  • Find these sections in “Responding to accidents and breakdowns”.

Exam trap: Wrong: place the beacon without checking stability and visibility. Right: place it securely where it is as visible as possible; if the body is higher than the cab, follow “Placing the beacon on a high cab”.

Read the full explanation
  • You must position the V-16 securely and with the greatest possible visibility; to choose the location on a lorry whose bodywork extends above the cab, follow the order in «Responding to accidents and breakdowns», section «Placing the beacon on a high cab». [DGT, placement on heavy vehicles](https://www.dgt.es/muevete-con-seguridad/tecnologia-e-innovacion-en-carretera/Dispositivos-de-presenalizacion-V16/).
  • Using the beacon together with the lights while immobilised is covered in «Responding to accidents and breakdowns», section «Hazard warning lights, position lights and end-outline marker lamps».
  • Deciding whether to leave the cab or remain inside is covered in «Responding to accidents and breakdowns», section «High-visibility vest and leaving the cab».

24High-visibility vest

A driver seated in the left driving position inside the cab of an articulated truck stopped beside the right edge of the road holds a high visibility vest with reflective bands.
The key idea

Carry a regulation-compliant vest in your non-special combination and keep it accessible.

Remember

  • Carry a high-visibility vest in your non-special combination.
  • Do not replace it with pale clothing or a small reflective strip.
  • Keep it accessible so you can put it on before leaving.
  • Keep its fabric and strips in good condition.

Exam trap: Wrong: pale clothing or any reflective strip replaces the vest. Right: carry a high-visibility vest that meets the rules.

Read the full explanation
  • You must carry a high-visibility reflective vest as part of the equipment for your non-special vehicle combination. It must meet the regulatory requirements for personal protective equipment; you must not replace it with a light-coloured garment or any clothing with a small reflective strip. [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • Wearing the vest when leaving the vehicle is covered in «Responding to accidents and breakdowns», section «High-visibility vest and leaving the cab». [RGC, art. 118.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a118).
  • As a preparation guideline, keep the vest accessible in the cab so that you can put it on before getting out. Keep its strips and fabric in good condition. Keeping it in a compartment that you can only reach by walking along the hard shoulder hinders the very protection you need when leaving the vehicle.

25Fire extinguishers for goods vehicle combinations

A driver checks two fire extinguishers secured in an open compartment of an articulated goods truck parked in a yard.
The key idea

Choose extinguishers using your combination’s MMA and maintain them regularly.

7,000 kgFirst band upper limit
20,000 kgSecond band upper limit
21A/113BFirst band rating
34A/144BHigher bands rating
Goods vehicle or combination MMA: general tableEquipment
From 3,500 to 7,000 kg inclusiveOne extinguisher rated 21A/113B
Above 7,000 up to 20,000 kg inclusiveOne extinguisher rated 34A/144B
Above 20,000 kgTwo extinguishers rated 34A/144B

Remember

  • Carry approved, serviceable equipment in your non-special combination.
  • You also need it when carrying ordinary goods.
  • Use the combination’s MMA, not its actual mass today.
  • The rating is not the extinguisher’s weight.
  • Check mounting, access, condition, seal and service indicators.
  • Dangerous goods also have specific rules.

Exam trap: Wrong: at 20,000 kg MMA you need two extinguishers. Right: one 34A/144B is required; above 20,000 kg, two are required.

Read the full explanation
  • You must carry suitable, type-approved firefighting equipment in working order in your vehicle combination, provided it is not a special vehicle combination. This obligation does not depend on carrying dangerous goods: it also applies to ordinary goods transport. You must check this equipment as part of your equipment checks before starting the transport operation. [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii).
  • For goods vehicles and vehicle combinations, the general requirement is one extinguisher with a 21A/113B rating from 3,500 up to and including 7,000 kg MMA (maximum authorised mass); above 7,000 and up to and including 20,000 kg, one with a 34A/144B rating; if you exceed 20,000 kg, two with a 34A/144B rating. You must use the MMA of the combination and distinguish which limits are inclusive. [Order of 27 July 1999, second provision](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#segundo).
  • With a combination whose MMA is 20,000 kg, you need one extinguisher with a 34A/144B rating under that table; with one whose MMA is 22,000 kg, you need two with that rating. You must read the extinguisher rating: the numbers and letters indicate extinguishing performance, and you cannot replace them with a figure in kilograms without checking the certified performance. [Order of 27 July 1999, second provision](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#segundo).
  • The Order allows, as an alternative, the minimum equipment required under ADR for the relevant MMA. If you carry dangerous goods, you must also comply with the specific regulations governing them. To answer an ordinary C+E question, first identify whether it asks about the general table or equipment subject to that regime. [Order of 27 July 1999, second provision](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#segundo).
  • The extinguishers must be portable and manually operated, with an extinguishing agent suitable for the vehicle, preferably dry powder or another suitable agent. The vehicle owner or the person they designate must check them regularly; in addition, at least the operations in Table II of Annex II to the Reglamento de instalaciones de protección contra incendios (RIPCI, Fire Protection Installations Regulations) must be carried out. As a practical check, inspect their mounting, accessibility, condition, seal and service indicators, and replace any defective extinguisher or report any fault. [Order of 27 July 1999, first provision](https://www.boe.es/buscar/act.php?id=BOE-A-1999-16887#primero).

Check the towed vehicle’s lights and markings

Check each function with the combination immobilised and the connections secured.

  1. Check the electrical connection and inspect the condition of lights, reflectors, plates and contour markings.
  2. Switch on the position lights and also check the number plate light, end-outline marker lamps and side marker lights where applicable.
  3. Operate each indicator and then the hazard warning lights; check the rear end of the combination.
  4. Check the brake lights, rear fog lamp and any fitted reversing lights with safe assistance.
  5. Rectify faults and remove anything obscuring the lights or markings before driving.

Inspect the combination’s wheel chocks

Relate each check to the points in «Wheel chocks on a significant slope».

  1. Selection: wheel size and mass permitted by the manufacturer.
  2. Condition: shape, integrity and cleanliness of the surfaces.
  3. Placement: the specified wheels and axles for each unit you need to immobilise.
  4. Contact: firm support on the ground and against the tyre tread.
  5. Storage: accessible holders and secure fastenings.

Use the V-16 from the cab

Warn others that your vehicle is immobilised without exposing yourself to traffic.

  1. Immobilise the combination and use the hazard warning lights and any other appropriate lights.
  2. Take the connected V-16 from its accessible storage place and activate it according to its instructions.
  3. To choose where to place it on a tall lorry, follow the sequence in «Responding to accidents and breakdowns», section «Placing the beacon on a high cab».
  4. Put on your high-visibility vest before leaving the cab if you are going to enter the carriageway or arcén (hard shoulder) on an interurban road.
  5. Leave the vehicle only if there is a safe place outside the carriageway and hard shoulder; otherwise remain inside with your seat belt fastened.

Check what you know

Real questions from the bank on this topic. Pick an answer to see the explanation.

1Does the C1E driving licence authorise you to drive a truck with a maximum authorised mass (MAM) exceeding 16,000 kg, towing a non-light trailer?
2The braking distance of a C1+E or C+E combination:
3If the combination of vehicles you are driving is towing a two-axle trailer, you should know that the MAM for each of the trailer's single axles must not exceed:
4In a test for the C1+E and C+E licences, the examiner may check that the applicant is wearing:

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module