Theory · AM Licence - Moped · Module 8 of 18

Moped lights and signals

You learn to choose the lights on your moped or light quadricycle according to the light, visibility and situation, and to signal your manoeuvres without dazzling others. You distinguish AM equipment from that of a motorcycle or car, and recognise vehicle plates and signs to answer exam questions.

27 min read25 sectionsReviewed Nov 2, 2026
A helmeted rider travels on a green moped in the right-hand lane at dusk, with a white headlamp on and a red rear light.
See and be seen without dazzling

1Seeing, being seen and giving warnings

A helmeted rider travels on a moped in the right-hand lane, with the headlamp illuminating the road, the red rear lamp and left indicator lit, and a red reflector below.
The key idea

Use lights to see, be seen and warn others.

Remember

  • Dipped beam and main beam help you see the road.
  • Position lights and reflectors show your presence.
  • Indicators and brake lights warn others of your actions.
  • Distinguish your moped from a motorcycle or car.
  • Keep every device required by your model’s type approval.
  • If you have optional lights, follow their rules of use.

Exam trap: Wrong: you can remove any light listed as optional in the general table. Right: keep lights required by your model’s type approval.

Read the full explanation
  • Lighting and signalling serve three purposes: dipped beam and main beam help you see the road; position lights and reflectors allow others to recognise your presence; indicators and brake lights communicate what you do. On a moped, its small size makes it especially important that you do not confuse having your lights on with having been noticed by others. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21)
  • The obligation to have a device fitted and the obligation to use it apply in different circumstances. Type approval determines what you have installed; driving conditions determine what you must switch on. An optional light also has specific uses prescribed by the regulations. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100) [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21)
  • Lighting equipment depends on whether you drive a two-wheeled moped, a three-wheeled moped or a light quadricycle. Bodywork, a steering wheel and several headlights on the latter do not automatically make all car lighting requirements applicable to it. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21)
  • You must retain the equipment required by your vehicle’s type approval. The general RGV tables explained in this module do not replace that approval. The published Annex IX to Regulation (EU) 3/2014 provides for number plate lighting for L1e-B and, for L2e and L6e, mandatory indicators and side reflectors as well, in addition to permitted extra devices. These details depend on the version applicable to each model’s type approval; they are not a universal answer for all AM vehicles. [RGV, arts. 20 and 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a20) [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030)

2Equipment for two-wheeled mopeds

A helmeted rider travels to the right on a two-wheeled moped with a white headlight, a red rear light, a rectangular red rear reflector and two amber side reflectors.
The key idea

Recognise the general equipment for your two-wheeled moped.

1 November 1999Exception up to this date
Two-wheeled moped: general tableEquipment
Dipped beam and rear position lightsOne or two per function
Brake lightsOne or two; optional if first used by 1 November 1999
Side reflectorsOne or two per side; optional if first used by 1 November 1999
Main beam, indicators and front position lightsOptional
Front reflector and number plate lightOptional

Remember

  • You need white dipped beam and red rear position lights.
  • You need a non-triangular red rear reflector.
  • Normally, you need red brake lights and amber side reflectors.
  • Reflectors return light; they are not lamps.

Exam trap: Wrong: every moped needs front position lights. Right: they are optional in the general table for two-wheeled mopeds. Also respect your model’s type approval.

Read the full explanation
  • The mandatory general equipment comprises one or two white dipped-beam headlights at the front and one or two red position lights at the rear. Front position lights are optional in the two-wheeled moped table. Not all mopeds have front position lights. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • Mandatory signalling equipment comprises one or two red brake lights, a non-triangular red rear reflector and amber side reflectors. The table provides for one or two reflectors on each side. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • For mopeds first put into service up to 1 November 1999, the general table makes the brake light and side reflectors optional. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • You may find one or two white main-beam headlights, direction indicators, front position lights, a white front reflector and number plate lighting listed as optional in the general table. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)

3Three-wheelers and light quadricycles

A green light quadricycle travels in its right-hand lane on a rural road, with two white dipped headlights and two white front position lights illuminated.
The key idea

Check your vehicle’s width and bodywork to know which lights you need.

1,300 mmWidth threshold
1 November 1999Brake light exception until then
Three-wheelers and light quadricycles: general tableWhat you need
Up to 1,300 mm wideOne or two dipped, brake and front/rear position lights; main beam if fitted
Over 1,300 mm wideTwo dipped, brake and front/rear position lights; two main-beam lights if fitted
Enclosed bodyworkIndicators required
Without enclosed bodyworkIndicators optional
Main beam, number plate light and side reflectorsOptional

Remember

  • You need dipped beam, front and rear position lights, brakes and non-triangular rear reflectors.
  • Dipped beam and front position lights are white; rear position and brake lights, red.
  • General table: brake lights are optional if first used by the date shown.
  • Centre any single light.

Exam trap: Wrong: bodywork makes your light quadricycle a car. Right: follow its category; enclosed bodywork requires indicators in the general table.

Read the full explanation
  • You must have dipped beam, front and rear position lights, brake lights and a non-triangular rear reflector under the general equipment requirements for these categories. Dipped beam and front position lights are white; rear position lights and brake lights are red. The brake light exception for vehicles first put into service up to 1 November 1999 also appears in this table. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • If the width exceeds 1,300 millimetres, the table requires two lights in the rows for dipped beam, main beam if fitted, brake lights, and front and rear position lights. Up to that threshold, one or two are permitted; a single light is placed on the median longitudinal plane. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • Under the RGV table, you must have direction indicators if the bodywork is enclosed; for vehicles without enclosed bodywork they are listed as optional. Main beam, number plate lighting and side reflectors also appear as optional. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)

4Colours and messages of each device

A helmeted rider travels to the right on a green moped with its white front headlight on, a red rear light and a rectangular red reflector below.
The key idea

Recognise each device by its colour, position and purpose.

DeviceWhat you recognise
Dipped beam, main beam and front position lightsWhite at the front
Rear position and brake lightsRed at the rear
Reversing lightWhite facing backwards
Number plate lightWhite light illuminating the plate
IndicatorsFlashing amber; together, they warn of danger
Approved fog lights on your quadricycle, if fittedWhite or selective yellow at the front; red at the rear

Remember

  • Do not judge a light by its colour alone.
  • Indicators flashing together form the hazard warning signal.
  • If your quadricycle has approved fog lights, distinguish front from rear.
  • A reflector returns light; a lamp produces light.

Exam trap: Wrong: a red part at the rear means you are braking. Right: it may be a reflector or a light with another purpose.

Read the full explanation
  • Dipped beam, main beam and front position lights are white; rear position lights and brake lights are red. A white light facing backwards may indicate reversing; the white number plate light illuminates the plate. The function of each device also depends on its location on the vehicle. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx) [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030)
  • Direction indicators emit flashing amber light. When they flash simultaneously to warn of a danger, they form the hazard warning signal. They are different from a red brake light and from a portable advance warning beacon. [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030)
  • If your quadricycle has type-approved fog lights, the front lights are white or selective yellow and the rear light is red. The rear fog light is neither a reversing light nor a heated rear window: it gives a light signal so that those following you can distinguish you in particularly adverse conditions. [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030) [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)
  • A reflector returns the light it receives; a lamp emits its own light. The rear reflector on a moped is red and non-triangular; it reflects the headlights of approaching vehicles even when your vehicle is switched off. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)

5Night-time and reduced visibility

A helmeted rider travels on a moped in the right-hand lane during heavy daytime rain, with the dipped headlight and rear light on.
The key idea

Switch on suitable lights at night and when visibility is seriously reduced.

10 mRead a number plate
50 mSee a dark vehicle

Remember

  • Switch on your lights from sunset to sunrise, in towns and outside them.
  • Switch on your lights even where there are streetlights.
  • Use lights when fog, heavy rain, snow, smoke or dust seriously reduces visibility.
  • Keep fitted position lights on with the correct front lighting.
  • Without fog lights, use dipped beam to see without dazzling others.
  • With normal eyesight, failing either distance check means the road is insufficiently lit.

Exam trap: Wrong: both distance checks must fail. Right: with normal eyesight, failing to read a plate at 10 m or distinguish a dark vehicle at 50 m anywhere on the carriageway is enough.

Read the full explanation
  • You must use the appropriate lights between sunset and sunrise. This obligation covers urban and interurban roads and does not depend on streetlights, illuminated shops or other vehicles whose headlights light your route. You must switch on the system appropriate to your own vehicle. [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98) [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101)
  • You must also use lights during the day when fog, heavy rain, snow, smoke, dust or a similar circumstance significantly reduces visibility. Being able to see the vehicle ahead is not enough: you must also assess whether others can recognise yours. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)
  • In these conditions, you must keep the fitted position lights on and use the appropriate permitted front lighting. On a moped without fog lights, dipped beam is the practical choice for lighting the road without dazzling others; you must not wait until nightfall to switch it on if heavy rain seriously impairs your vision. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99) [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)
  • A road is insufficiently lit if, with normal eyesight, at some point on the carriageway you cannot read a number plate at 10 metres or distinguish a dark vehicle at 50 metres. Failure of either test is enough; you do not have to wait until both fail. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100)

6Dipped beam by day and daytime running lights

A helmeted rider rides an orange moped with its dipped headlight on in the right-hand lane of an open road in broad daylight with good visibility.
The key idea

Distinguish daytime running lights from the lighting needed in tunnels, darkness or poor visibility.

Vehicle or deviceWhat you must distinguish
MotorcycleDipped beam required by day on any road
Moped in good daytime visibilityDipped beam recommended; keep your approved automatic system working
Tunnel, night or seriously reduced visibilitySelect the required lighting; do not rely only on daytime running lights

Remember

  • You can use dipped beam by day to make yourself more visible.
  • Keep your model’s approved automatic lighting system working.
  • Do not assume daytime running lights switch on your rear lights.
  • In tunnels, at night or with seriously reduced visibility, select the required lights.
  • Check your lights even if they work automatically.

Exam trap: Wrong: daytime running lights suffice in a tunnel at midday. Right: select the mandatory tunnel lighting, even if the sensor has not detected darkness.

Read the full explanation
  • Article 104 establishes that the general obligation to use dipped beam during the day on any road applies to motorcycles. Your moped does not become a motorcycle because it has two wheels or looks like a scooter. [RGC, art. 104](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a104)
  • As a recommendation to make yourself visible, you can use dipped beam during the day even in good visibility. You must keep your model’s type-approved automatic system working: European legislation provides for daytime running lights or automatic dipped-beam activation according to the category and configuration. [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030) [RGC, art. 104](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a104)
  • Daytime running lights make the vehicle more visible from the front during the day. You must not confuse them with position lights or assume that they switch on all the rear lights. In a tunnel, at night or in significantly reduced visibility, you must select the lighting required for that situation. [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030) [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98) [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)
  • You must check the lights even if the control has an automatic setting. In a tunnel at midday, you must select the mandatory lighting even if the automatic sensor has not detected darkness; check your model’s controls and warning lights. [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98) [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101)

7Tunnels and underpasses

A helmeted rider drives a moped with its headlight and rear light on while entering an illuminated tunnel in daylight.
The key idea

Enter tunnels and underpasses with suitable lights, even by day.

Tunnel conditionsWhat you must use
Sufficiently litPosition lights and dipped beam, even by day
Insufficiently litPosition lights and dipped or main beam, depending on equipment, speed and dazzle
No main beam or risk of dazzling othersPosition lights and dipped beam

Remember

  • The S-5 sign also marks a section where you must use lights.
  • Only enter if your vehicle is allowed on that road.
  • Select your lights before entering and check that they stay on.
  • On leaving, check whether visibility means you must keep them on.

Exam trap: Wrong: position lights suffice because the tunnel has streetlights. Right: in a sufficiently lit tunnel, use position lights and dipped beam, even by day.

Read the full explanation
  • You must switch on the appropriate lights at any time when entering a tunnel, underpass or section covered by the S-5 tunnel sign. This obligation also applies to mopeds and light quadricycles, provided they are allowed on the road. [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98)
  • If the tunnel is sufficiently lit, you must use position lights and dipped beam, even in broad daylight. The tunnel’s fixed lighting helps you see your surroundings but does not remove your lighting obligation. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99) [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101)
  • If the tunnel is insufficiently lit, you must choose between dipped beam and main beam according to your equipment, speed and the possibility of dazzling others. If you do not have main beam, you must use dipped beam. If you could dazzle others, you must also use dipped beam even if you have entered a dark area. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100) [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101)
  • As a safety procedure, you must select the lights before entering and check that they stay on throughout the section. On leaving, you must assess visibility outside: a cloud of smoke or heavy rain may require you to keep the lights on even outside the tunnel. [RGC, art. 98](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a98) [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)

8Special lanes and lighting

A helmeted rider travels in daylight on a moped with its dipped headlight on in a reversible lane bounded by double broken lines and opened by an illuminated green arrow.
The key idea

Use dipped beam by day and night in special lanes and affected neighbouring lanes.

Lane you are usingRequired lighting by day and night
ReversibleAt least dipped beam
Temporary additional lane or lane opened in the opposite directionDipped beam
Normal direction alongside a lane opened in the opposite directionDipped beam
Hard shoulder or lane alongside a temporary additional laneDipped beam

Remember

  • Use at least dipped beam, day and night, in the special lanes listed.
  • Follow lighting rules for affected neighbouring lanes too.
  • Check access conditions in “Using the road with a moped”.

Exam trap: Wrong: you only need dipped beam when someone approaches. Right: use it by day and night in the listed lanes, even when nobody approaches.

Read the full explanation
  • You must use at least dipped beam, both by day and by night, when using a reversible lane. The lighting obligation does not depend on whether someone is approaching at that moment; it forms part of the conditions for using the lane. [RGC, art. 40](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a40) [RGC, art. 104](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a104)
  • Dipped beam is compulsory in temporary additional lanes and lanes opened in the opposite direction to normal traffic. You must also use it in adjacent lanes when their rules require it: in the normal direction alongside a lane opened in the opposite direction, and on the hard shoulders or lanes alongside a temporary additional lane. [RGC, art. 104](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a104) [RGC, art. 41](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a41) [RGC, art. 42](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a42)
  • Access conditions, authorised vehicle categories and speeds for these lanes are explained in the Using the road with a moped module.

9Position lights: presence and width

A helmeted rider rides a moped in the right-hand lane at night, with the red rear position light on and the headlight illuminating the road.
The key idea

Use position lights to show your presence and width, alongside the correct driving lights.

Remember

  • Do not drive at night with position lights alone.
  • Use them in tunnels, underpasses and seriously reduced visibility too.
  • Do not change the wiring to switch off rear signals.

Exam trap: Wrong: drive at night with position lights alone. Right: add dipped beam or the appropriate front lighting.

Read the full explanation
  • You must use position lights to signal your presence and allow others to judge the vehicle’s width. On their own, they do not provide the lighting you need to drive at night: when moving, you must use them with dipped beam or the front lighting appropriate to the conditions. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99) [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101)
  • You must use position lights at night, in significantly reduced visibility and in tunnels or underpasses. The obligation to use them applies to the devices fitted to the vehicle under the regulations; it does not make front position lights mandatory on all two-wheeled mopeds. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99) [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21)
  • Rear position lights allow others to locate your moped from behind, where the dipped-beam headlight does not indicate the vehicle’s presence. You must recognise them as lights indicating presence to interpret correctly what you see when approaching another AM vehicle, without confusing their steady light with a braking warning. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • Rear position lights come on with dipped beam, main beam and other lighting specified in the regulations. You must not alter the circuit to keep a front headlight on while disabling rear signalling. Brief light warnings are treated specifically and differently from continuous lighting. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15)

10Dipped beam: the usual light for driving

A helmeted rider travels on a moped in the right-hand lane of an urban street at night, with streetlights on and the white low-beam headlight illuminating the nearby road.
The key idea

Use dipped beam to see nearby and match your speed to what you can see.

40 km/hSpeed threshold
Night-time situationWhat you must use
Built-up area, whether well lit or darkPosition lights and dipped beam
Outside built-up areas, sufficiently litPosition lights and dipped beam
Outside, insufficiently lit, without main beam or with dazzle riskPosition lights and dipped beam
Outside, insufficiently lit, up to 40 km/h without using main beamYou may use dipped beam when not using main beam; keep position lights on

Remember

  • White front dipped beam is required equipment for AM vehicles.
  • If you only have dipped beam, match your speed to what you can see.

Exam trap: Wrong: exceeding 40 km/h requires main beam even if your moped has none. Right: that obligation applies to vehicles equipped with it; with dipped beam alone, adapt your speed.

Read the full explanation
  • Dipped beam, or short-range lighting, is white front lighting. It is mandatory equipment in AM categories. It does more than make you visible: it lets you distinguish the nearby carriageway without using the long-range beam. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • In built-up areas at night, you must use position lights and dipped beam whether the road is sufficiently lit or not. [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101)
  • Outside built-up areas, on a sufficiently lit road, you must use position lights and dipped beam between sunset and sunrise. On an insufficiently lit road, you must use dipped beam if you have no main beam, if you are travelling at no more than 40 kilometres per hour without using main beam, or if there is a possibility of dazzling others. [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101)
  • If your moped only has dipped beam, you must adapt your speed to the distance you can see. The obligation to use main beam above 40 kilometres per hour applies to vehicles equipped with it; it does not require you to invent a main-beam function on a vehicle type-approved without that device. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100) [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101)

11Main beam and the 40 km/h threshold

A helmeted rider travels on a moped in the right-hand lane of a rural road at night, with the high beam and rear position light illuminated.
The key idea

If you have main beam, use it when required and dip it when necessary.

40 km/hYou must exceed this threshold
Speed with main beam fitted and suitable conditionsWhat you must remember
Above 40 km/hMain beam required unless dipped beam is needed
40 km/h or lessDipped beam allowed; main beam is not always forbidden

Remember

  • Main beam is optional in the general AM equipment table.
  • Apply this threshold at night, outside built-up areas, on insufficiently lit roads.
  • In dark tunnels, consider equipment, speed and dazzle risk at any time.
  • Keep required position lights on, even without adding dipped beam to main beam.
  • Do not use main beam when stopped or parked.
  • In built-up areas at night, drive with dipped beam.

Exam trap: Wrong: more than 40 km/h includes exactly 40 km/h. Right: you must exceed that speed, have main beam fitted and meet the road, lighting and no-dazzling conditions.

Read the full explanation
  • You may find one or two white main-beam headlights on a moped. Their installation is listed as optional in the AM tables. If your model has these lights, you must use them when the road, lighting and speed conditions prescribed by the regulations are met. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • If you have main beam, you must use it when travelling at more than 40 kilometres per hour at night, outside built-up areas and on an insufficiently lit road, unless dipped beam is required. The rule also covers insufficiently lit tunnels and underpasses at any time, subject to the exceptions for dipped beam and dazzling others. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100)
  • The threshold requires you to exceed 40 kilometres per hour: at exactly 40 kilometres per hour, this speed-based obligation does not arise. At speeds no greater than 40, you can use dipped beam when not using main beam; this does not mean main beam is absolutely prohibited at lower speeds when its conditions of use are met. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100) [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101)
  • You must keep the position lights on when required and can use main beam alone or together with dipped beam as front lighting. “Main beam alone” means you do not need to add the dipped beam; it does not permit you to switch off the required rear position lights. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99) [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100)
  • You must not use main beam with the vehicle stopped or parked, or flash your headlights for unauthorised purposes. Within built-up areas, you must drive with dipped beam in the night-time circumstances specified; brief light warnings allowed by the regulations are covered as warnings, rather than continuous lighting. [RGC, art. 100](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a100) [RGC, art. 101](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a101) [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)

12Avoiding and experiencing dazzle

A helmeted rider rides a moped with its dipped headlight directed onto the asphalt as a car approaches in the opposite lane at dusk.
The key idea

Dip your headlights whenever you could dazzle others; slow down if you are dazzled.

Remember

  • Do not wait for a fixed distance or another driver’s complaint.
  • Protect users of other routes reached by your lights too.
  • Dip your headlights even if the other driver keeps main beam on.
  • Wait until you have passed the oncoming vehicle before restoring main beam.
  • You can dazzle the driver ahead through their mirrors.
  • If dazzled, slow down; stop if necessary.

Exam trap: Wrong: keep main beam on because the other driver does. Right: dip your headlights as soon as you could dazzle anyone, including through mirrors.

Read the full explanation
  • You must change from main beam to dipped beam as soon as you identify any possibility of dazzling others. This protection covers users of your road and of another transport route who may receive the beam. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102)
  • You must dip your headlights even if an oncoming driver keeps main beam on. When passing an oncoming vehicle, you must not restore main beam until you have passed its position. Dazzling the other driver in return makes it even harder for both of you to maintain a safe course. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102)
  • You must also avoid dazzling anyone travelling ahead of you: your main beam can reach them through their mirrors. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102)
  • If you are dazzled, you must reduce your speed as much as necessary, even stopping, to avoid hitting vehicles or pedestrians ahead. As practical advice, avoid staring at the light source and maintain a safe reference for your course; do not react by accelerating or switching off all your lights. [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102)

13Front fog lights

A helmeted rider travels on a moped in the right-hand lane of a foggy road, with the front fog light switched on and its low beam illuminating the road.
The key idea

If you have approved front fog lights, use them only in permitted conditions.

6.50 mMaximum width for signed bends
Case with approved front fog lights fittedWhen you may use them
Seriously reduced visibilityFog, heavy rain, snow, smoke, dust or similar conditions
Without bad weatherCarriageway at most 6.50 m wide, with signs warning of closely spaced bends

Remember

  • Front fog lights are not generally required equipment for AM vehicles.
  • You may use them without dipped or main beam; keep required position lights on.
  • You may combine them with dipped beam or main beam when appropriate.

Exam trap: Wrong: a narrow road alone allows fog lights without bad weather. Right: the carriageway must be 6.50 m wide or less and have signs warning of a series of closely spaced bends.

Read the full explanation
  • If your vehicle has type-approved front fog lights, you can use them in the circumstances explained below. They are not part of the general mandatory AM equipment. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21)
  • If fitted, you can use the front fog light in fog, heavy rain, snow, smoke, dust or other conditions that significantly reduce visibility. Its use is not reserved exclusively for thick fog, a more demanding condition associated with the rear fog light. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)
  • You can use it as front lighting without dipped beam or main beam, or together with dipped beam and even with main beam where appropriate. You must keep the required position lights on and observe the permitted circumstances of use; “on its own” does not mean permission to drive with every other light off. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99) [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)
  • You can also use it on narrow sections with many bends: the carriageway must be 6.50 metres wide or less and marked with signs warning of a series of closely spaced bends. You must meet both conditions; a single bend or a road that merely looks narrow is not enough. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)

14Rear fog light

A helmeted rider travels on a moped in the right lane of a road in dense fog, with the red rear fog light switched on.
The key idea

If you have a rear fog light, use it only in especially bad conditions.

Remember

  • Use in thick fog, very heavy rain, heavy snow or dense smoke or dust.
  • It makes you visible from behind in especially bad conditions.
  • Switch it off when those conditions end.
  • It needs main beam, dipped beam or front fog lights already on.

Exam trap: Wrong: keep your rear fog light on in light fog. Right: switch it off when especially bad conditions end, even if you still need other lights.

Read the full explanation
  • If your vehicle has one, you must use the rear fog light only in particularly adverse conditions: thick fog, very heavy rain, heavy snowfall or dense clouds of dust or smoke. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)
  • The rear fog light makes you visible from behind in very adverse conditions. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106) [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030)
  • You must switch it off when the particularly adverse conditions justifying its use disappear. If the fog becomes light, other lighting may still be mandatory because of reduced visibility, but that does not mean you must keep the rear fog light on. [RGC, art. 106](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a106)
  • The rear fog light can only be switched on when main beam, dipped beam or front fog lights are on. Its circuit and function are specific. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15)

15End-outline marker lamps and side marker lamps

A moped with a helmeted rider travels on the right while a truck approaches in the opposite lane with two white clearance lamps at the upper corners of its cargo box.
The key idea

Distinguish lights showing overall width from side marker lamps and side reflectors.

2.10 mWidth you must exceed
6 mGeneral side marker length threshold
DeviceWhat you must recognise
End-outline marker lamps on wide vehiclesWhite at the front and red at the rear
Width over 2.10 mAdd end-outline marker lamps when position lights are required
Motor vehicles longer than 6 mGeneral side marker rule; do not automatically apply it to AM vehicles
Approved side marker lamps on L2e or L6eAmber; red permitted at the rear under specified conditions

Remember

  • End-outline marker lamps show overall width and supplement position lights.
  • Do not treat them as usual required AM equipment.
  • Do not automatically apply long motor vehicles’ side marker rules to your quadricycle.
  • Check your vehicle’s category and type approval.
  • Side marker lamps emit light; side reflectors return it.

Exam trap: Wrong: exactly 2.10 m wide requires end-outline marker lamps. Right: width must exceed 2.10 m; these are not ordinary mandatory AM equipment.

Read the full explanation
  • End-outline marker lamps indicate the vehicle’s overall width and supplement position lights. Under the general rule for wide vehicles, they are white at the front and red at the rear. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • Article 99 establishes that if the width exceeds 2.10 metres, end-outline marker lamps are added to position lights in the circumstances where they are mandatory. Exactly 2.10 does not mean more than 2.10. [RGC, art. 99](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a99)
  • The general AM tables do not establish end-outline marker lamps as ordinary mandatory equipment. You must not automatically apply the general obligation for side marker lamps on motor vehicles longer than 6 metres to your light quadricycle either; you must consult its category and type approval. [RGV, art. 16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a16) [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • If an L2e or L6e has side marker lamps under its type approval, you must distinguish them from its side reflectors. The European regulation permits these additional lights: they are amber, with amber or red permitted at the rear under the specified conditions. [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030)

16Reflectors and pedals

A green moped parked beside the right kerb shows a rectangular red rear reflector and an amber side reflector.
The key idea

Recognise the reflectors you need for your vehicle, its width and its pedals.

1 mRear reflector width threshold
FourReflectors with fixed pedals
Three-wheelers and light quadricycles: widthRear reflectors you need
Up to 1 mOne
Over 1 mTwo

Remember

  • You need a non-triangular red rear reflector.
  • Triangular rear reflectors identify trailers in the general equipment rules.
  • Keep side reflectors clean and uncovered so others can see you from the side.
  • With fixed pedals, you need four amber reflectors: two per pedal.

Exam trap: Wrong: use 1,300 mm as the rear reflector threshold. Right: for three-wheelers and light quadricycles, the threshold is 1 m.

Read the full explanation
  • Under the general equipment requirements, triangular rear reflectors are for trailers; for AM, you must identify the non-triangular device described in the equipment sections. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • On a three-wheeler or light quadricycle, rear reflector equipment depends on width: one on vehicles up to 1 metre wide and two above that width. This differs from the 1,300 millimetre threshold used to require two lights in certain rows of their table. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • Side reflectors reflect light coming from the side and allow others to notice your moped at a junction or where paths cross. You must keep their surfaces clean and uncovered so that they can fulfil this function. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • If you have non-retractable pedals, you must have four amber reflectors: two on each pedal. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)

17Direction indicators

A helmeted rider travels on a green moped beside the right-hand kerb with the right direction indicators illuminated.
The key idea

Signal your sideways movement early and cancel the indicator once you take your new course.

Two per sideIndicators in moped equipment table

Remember

  • If fitted, use the indicator on the side you intend to move towards.
  • Give enough advance warning; indicators are amber.
  • Keep signalling throughout the manoeuvre; cancel once you take your new course.
  • When overtaking, signal moving out and moving back in separately.
  • To pull over, indicate the side and give any required slowing-down warning.
  • Indicators do not allow prohibited turns or force others to let you in.

Exam trap: Wrong: your indicator gives you priority. Right: give way to traffic in the lane you want to enter.

Read the full explanation
  • You must give sufficient advance warning of manoeuvres involving lateral movement. If you have indicators, use the one on the side towards which you intend to move. The lights are amber; the moped table places them at the front and rear, two on each side. [RGC, art. 108](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a108) [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • You must maintain the light signal throughout the manoeuvre and end it once you have adopted the new course. When overtaking, moving out and moving back in are separate lateral movements; leaving one indicator on throughout may communicate the wrong intention. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)
  • When pulling over to stop or park, you must use the indicator on the side where you intend to stop, if fitted, in addition to the appropriate slowing-down warning. You must not replace that direction signal with hazard warning lights when you need to indicate a particular side. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)
  • The indicator communicates your intention to move. Even with it switched on, you must give way to anyone travelling in the lane you intend to enter. Switching it on does not permit a prohibited turn or oblige others to let you in immediately either. [RGC, art. 74](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a74) [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)

18Arm signals

A helmeted rider travels on a moped in the right lane and extends her left arm horizontally, palm facing down, to signal a move to the left.
The key idea

Without a light signal, use clear, visible arm signals in the prescribed way.

Your arm signalWhat you announce
Horizontal, palm downMovement towards the side your hand points to
Bent upwards, palm openMovement towards the opposite side
Left arm horizontalLeft
Left arm bent upwardsRight
Short, quick movements up and downSlowing considerably or intending to stop
Horizontal, palm backwards, without a reversing lightReversing

Remember

  • A valid hand signal overrides a conflicting visual signal.
  • Make signals that others can see and understand.
  • Signalling does not remove the safety conditions for your manoeuvre.

Exam trap: Wrong: any horizontal arm signal means the same thing. Right: palm down signals sideways movement; palm backwards signals reversing when you have no reversing light.

Read the full explanation
  • If you have no light signal available to warn of the manoeuvre, you must use your arm in the prescribed, clearly visible way. A valid hand signal overrides any conflicting visual signal. Any gesture will not do: others must be able to understand and see it. [RGC, art. 108](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a108)
  • To move towards the side your hand points to, you must extend your arm horizontally with your palm facing down. For the opposite side, you must bend it upwards with your palm open. With your left arm, horizontal means left and bent upwards means right. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)
  • To give a hand signal warning of a considerable reduction in speed or your intention to stop, move your arm alternately up and down with short, quick movements. The option of using brake lights instead is explained in “Braking and reversing”. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)
  • To announce reversing when you have no reversing light, you must extend your arm horizontally with your palm facing backwards. The palm’s orientation distinguishes this warning from others. Signalling does not remove the manoeuvre’s safety conditions; how to perform it is covered in the Moped manoeuvres module. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)

19Braking and reversing

A helmeted rider rides a green moped in the right lane, with its red brake light illuminated and a blank yellow rear licence plate.
The key idea

Your brake light warns of braking; your white rear light signals reversing.

LightWhat it tells you
Red brake lightYou are applying the service brake
Red position lightYou are showing your presence
White reversing light, if fitted to your quadricycleYou are reversing or ready to reverse; it lights the area behind

Remember

  • Keep your required brake light working.
  • Not every moped needs a third brake light.
  • Where possible, warn before slowing considerably or when you intend to stop.
  • Use brake lights repeatedly or the prescribed arm movement.
  • Do not delay essential braking to give a warning first.

Exam trap: Wrong: a reversing light only signals movement already started. Right: it can also mean you are ready to reverse.

Read the full explanation
  • Red brake lights warn that the service brake is being applied. Position lights indicate presence, while the reversing light is white. The brake lights warn those following you so that they can react to your reduction in speed. [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx) [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030)
  • You must keep the brake light required on your vehicle working. Its equipment requirements are detailed in the sections on two- and three-wheelers and light quadricycles; you must not require a third brake light on every moped. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21)
  • Whenever possible, you must warn of a considerable reduction in speed or your intention to stop by repeatedly using the brake lights or making the prescribed arm movement. This includes slowing down because of traffic; you must not delay essential braking to give a warning first. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)
  • If your light quadricycle has a white reversing light, it illuminates the area behind and announces that the vehicle is reversing or ready to reverse. The conditions for the manoeuvre are covered in the Moped manoeuvres module. [Regulation (EU) 3/2014, Annex IX](https://www.boe.es/buscar/doc.php?id=DOUE-L-2014-80030) [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)

20Hazard warning lights: warning of danger

A moped immobilized on the right shoulder of a foggy road displays both rear indicators illuminated and its red rear position light.
The key idea

Use hazard warning lights to warn of danger; you must still obey traffic rules.

SituationHow you must warn others
Stationary with seriously reduced visibilityHazard warning lights if fitted; position lights when required
Moving below the required minimum, with risk of being hit from behindHazard warning lights if fitted
Exceptional emergency meeting the legal conditionsIntermittent horn and hazard lights if fitted; or a handkerchief or similar warning

Remember

  • Hazard warning lights make your indicators flash together.
  • They do not let you park illegally or ignore priority rules.
  • You must still obey traffic rules during an exceptional emergency.
  • If fitted, use them in the required cases.
  • Do not keep them on simply because your moped travels more slowly.

Exam trap: Wrong: always use hazard lights because you are slow. Right: while moving, use them if fitted when you cannot reach the required minimum and risk being hit from behind.

Read the full explanation
  • With the hazard warning signal, you operate the indicators simultaneously to warn of danger. You must use it in the circumstances prescribed by the regulations if your vehicle has it. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)
  • If you become stationary in a place or circumstances that significantly reduce visibility, you must signal your presence with hazard warning lights if fitted and, where required, position lights. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109)
  • You must use hazard warning lights while moving when you cannot reach the required minimum speed and there is a risk of being hit from behind. The danger condition matters: you must not interpret this as requiring a moped always to travel with hazard warning lights because it is slower than other vehicles. [RGC, art. 49](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a49)
  • The hazard warning signal warns of danger, and you must continue to obey parking prohibitions and priority rules. In an exceptional emergency under article 70, you can give a warning by sounding your horn intermittently and using hazard warning lights, if fitted, or with a handkerchief or similar method, but you must obey the traffic rules. [RGC, art. 70](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a70)

21Lights on a stationary vehicle

A moped immobilized at night on the right shoulder keeps its white front position light and red rear position light on.
The key idea

When stationary, keep the lights needed for others to see you.

SituationWhat you must do
Stopping or parking at night on an insufficiently lit through road in a built-up areaKeep position lights on if on the carriageway or hard shoulder
Parked parallel to the kerb on that through roadWith an approved setup, replace them with parking lights or carriageway-side position lights
Parked on an urban road other than a through roadYou may switch position lights off if lighting makes you visible far enough away
Tunnel congestionKeep position lights on; temporarily use hazard lights if fitted

Remember

  • At night or in seriously reduced visibility, keep position lights on when stationary.
  • This applies on the carriageway or hard shoulder.
  • Add end-outline marker lamps where required.
  • The rule also applies when you stop because of a breakdown.
  • Recognise parking lights: white at the front and red at the rear.

Exam trap: Wrong: you can replace position lights with parking lights on any road. Right: this applies when parked parallel to the kerb at night on an insufficiently lit through road in a built-up area, with an approved lighting setup.

Read the full explanation
  • If you become stationary at night or in significantly reduced visibility on the carriageway or arcén (hard shoulder), you must keep the position lights on and, where required, the end-outline marker lamps. The rule does not depend on whether you chose to stop: it also applies to a breakdown. [RGC, art. 105](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a105)
  • On an insufficiently lit travesía (a through road in a built-up area), you must keep the position lights on when stopping or parking at night on the carriageway or hard shoulder. If parked parallel to the kerb, you can replace them with parking lights or the two position lights on the carriageway side when your vehicle has that authorised configuration. [RGC, art. 105](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a105)
  • Parking lights signal a parked vehicle and emit white light towards the front and red towards the rear. You must not assume that all mopeds have them or apply the substitution allowed on a travesía to any breakdown stop on a road. [RGC, art. 105](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a105) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • On an urban road other than a travesía, you can leave a parked vehicle without position lights if the lighting allows it to be distinguished at a sufficient distance. [RGC, art. 105](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a105)
  • If you stop inside a tunnel because of congestion, you must keep the position lights on and temporarily switch on hazard warning lights if your vehicle has them, to warn those approaching from behind; the other actions are explained in the Using the road with a moped module, and those for a breakdown or fire in the Accidents, breakdowns and first aid module. [RGC, art. 97](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a97)

22V-16 and breakdown warning signals

A moped stopped beside the right-hand curb has a flashing yellow beacon on its rear top box, while a person wearing a helmet and reflective vest waits on the pavement.
The key idea

Use the connected V-16 to warn of a hazardous immobilisation.

Remember

  • The connected V-16 is the regulatory device for warning of a hazardous immobilisation.
  • Check carrying, use and placement in “Accidents, breakdowns and first aid”.
  • See “V-16: what applies to the AM licence”.

Exam trap: Wrong: a triangle is the regulatory warning device for a Spanish vehicle. Right: the connected V-16 is the regulatory device for warning of a hazardous immobilisation.

Read the full explanation
  • The connected V-16 is the regulatory device for giving advance warning of a hazardous immobilisation; consult the requirements to carry and use it and its placement in “Accidents, breakdowns and first aid”, under “V-16: what applies to the AM licence”. [RGC, art. 130.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130) [RGV, Annex XI, V-16](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-16) [RGV, Annex XII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii)

23Number plates and their lighting

A helmeted rider rides a moped in the right lane of a road, with the yellow rear registration plate illuminated by a white light.
The key idea

Keep your yellow number plate visible and switch on its light when required.

Four digitsAfter C
Three lettersAfter the digits
Plate or deviceWhat you must recognise
Rear plate on mopeds and light quadricyclesRequired
Front plate on a light quadricycleOptional; same features as the rear plate
Number plate lightWhite; illuminates the rear plate

Remember

  • Your plate has a reflective yellow background and black characters.
  • Its combination starts with C, then four digits and three letters.
  • Keep the rear plate vertical or nearly vertical.
  • Keep its light working if your vehicle has one.
  • If required equipment, switch it on when driving conditions require lights.

Exam trap: Wrong: every AM vehicle needs front and rear number plates. Right: you need the rear plate; a front plate is optional on light quadricycles.

Read the full explanation
  • The standard number plate for mopeds and light quadricycles has a retroreflective yellow background and black characters. Its combination includes the letter C, four digits and three letters. [RGV, Annex XVIII, I.A.d](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii)
  • You must have a rear plate, vertical or nearly vertical. A light quadricycle may also have an optional front plate with the same characteristics as the rear one. [RGV, Annex XVIII, III.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxviii)
  • You must keep the plate visible and its lighting working if your vehicle has it. The number plate light is white and is intended to illuminate the rear plate. [RGV, art. 21](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a21) [RGV, Annex X](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx)
  • When you must use lights because of the driving conditions, you must also switch on the number plate lighting if your vehicle is required to have it. [RGC, art. 103](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a103)

24V-13, V-19 and other vehicle signs

A helmeted person rides a moped in the right lane of a road, with the green novice driver plate visible on the left rear.
The key idea

Recognise the vehicle signs you need and position them correctly for your vehicle.

One yearV-13 for your first licence
40 km/hMaximum design speed for V-5
SignWhat you must recognise
V-13Novice driver; flexible rear position for motorcycles, reduced-mobility vehicles and three-wheelers
V-19Passed inspection and next due date; inside windscreen, top right; otherwise visible; historic vehicles exempt
V-4Specific speed restriction when applicable
V-5Motor vehicles or combinations unable by design to exceed 40 km/h
V-20Diagonal red and white stripes; permitted load projecting at the rear

Remember

  • If AM is your first licence, display V-13 for the required period.
  • Pause that period while your licence is invalid, confiscated or you are banned.
  • Another licence held effectively for at least one year means you are not first-time.
  • That licence can be national or foreign, of any class.
  • On two-wheeled mopeds and light quadricycles, display V-13 visibly at the rear left.
  • Do not use V-20 to justify a prohibited projecting load.

Exam trap: Wrong: put V-13 anywhere at the rear of your two-wheeled moped. Right: display it visibly at the rear left; the motorcycle exception does not cover two-wheeled mopeds or light quadricycles.

Read the full explanation
  • If AM is your first licence, you must display the V-13 novice driver plate for one year, under the time-calculation rules in Annex XI. On your two-wheeled moped and light quadricycle, you must place it visibly at the rear left. The exception allowing it anywhere visible at the rear lists motorcycles, vehicles for people with reduced mobility and three-wheeled vehicles; you must not extend it to a two-wheeled moped because it resembles a motorcycle, or to a light quadricycle. [RGV, Annex XI, V-13.1-3](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-13)
  • The calculation of this one-year period is suspended during the loss of licence validity, confiscation of the licence or deprivation of the right to drive provided for in the regulations. It is not considered your first licence if you have held another national or foreign licence of any class with at least one year of effective possession. [RGV, Annex XI, V-13](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-13)
  • The V-19 indicates a successful periodic ITV (vehicle roadworthiness test) and the date of the next inspection. If you have a windscreen, it is placed inside at the top right; on other vehicles, in a clearly visible place. Vehicles classified or registered as historic are exempt from displaying this sticker. [RGV, Annex XI, V-19](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-19) [RD 920/2017, art. 12](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a12)
  • The V-4 indicates a specific speed restriction in the circumstances prescribed by the regulations; you must display it when one of them applies to you. You must not attribute the V-5 slow vehicle sign to your vehicle either: it refers to motor vehicles or combinations which, by construction, cannot exceed 40 kilometres per hour. [RGV, Annex XI, V-4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-4) [RGV, Annex XI, V-5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-5)
  • If you carry a load projecting at the rear in a permitted situation, you must mark it with the V-20 panel with diagonal red and white stripes. Load dimensions and the conditions allowing overhang are covered in the Passengers and loads on a moped module; the panel does not in itself authorise a prohibited overhang. [RGV, Annex XI, V-20](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#v-20)

25Headlight flashes, horn and checks

A helmeted person cleans the illuminated headlamp of a green moped parked beside the right-hand curb of a street.
The key idea

Give warnings only when allowed; keep your lights clean, visible and correctly aimed.

WarningWhen you may use it
Brief dipped-beam or main-beam flashesPermitted warning purposes, even in built-up areas, without dazzling others
Non-shrill hornAvoid an accident; announce overtaking outside built-up areas; legally permitted exceptional emergency

Remember

  • Do not flash to greet, demand priority or warn of police checks.
  • Keep lights clean, working and correctly aimed; paired devices must match and be symmetrical.
  • Slow down if an unrepairable fault during your journey reduces lighting.
  • You must be able to stop within the lit area.
  • Keep lights, plates and arm signals clear; never fit unauthorised paints, lights or reflectors.
  • When refuelling, switch off lights, engine and required electrical systems, including at self-service pumps.

Exam trap: Wrong: use your horn in town just to announce overtaking. Right: that purpose only allows horn use outside built-up areas; in town, you may use it to avoid a possible accident or for a legally permitted exceptional emergency.

Read the full explanation
  • You can give brief light warnings with dipped beam, main beam or both alternately for the warning purposes prescribed by the regulations, even in built-up areas, without dazzling others. You must not flash your headlights to demand priority, greet someone or warn of a police checkpoint. The warning does not change the recipient’s obligations. [RGC, art. 109](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a109) [RGC, art. 110](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a110)
  • You can use a horn with a non-shrill sound to avoid a possible accident, announce your intention to overtake outside built-up areas or warn of the exceptional urgency prescribed by the regulations. You must not use it without cause or excessively; within built-up areas, an intention to overtake alone does not justify its use. [RGC, art. 110](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a110)
  • You must keep your lights clean, working and correctly aligned as a practical check before driving. Dipped beam aimed too low shortens the area you can see; a poorly aligned beam can dazzle others. If you fit paired devices serving the same purpose, they must match in colour and intensity and have the prescribed symmetrical arrangement. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15) [RGC, art. 102](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a102)
  • If a fault that cannot be repaired en route forces you to drive with reduced lighting intensity, you must reduce your speed until you can stop within the illuminated area. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107)
  • You must not apply unauthorised paints or fit unauthorised lights or reflective devices, even if you believe they make you more visible. When carrying luggage, you must keep lights, number plates and hand signals unobstructed. A case, cover or accessory must not prevent others from recognising your signals. [RGV, art. 15](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a15) [RGC, art. 14](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a14)
  • When refuelling, you must switch off the vehicle’s lights as well as the engine and the electrical systems specified in the regulations. You must also comply at self-service pumps. [RGC, art. 115](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a115)

Choosing lights when entering a tunnel

Apply the lighting obligation even during the day.

  1. Before entering, check that your vehicle is allowed in the tunnel and on the road.
  2. Switch on position lights and dipped beam: daytime running lights are not enough.
  3. If it is insufficiently lit, assess the main-beam rules according to equipment, speed and the possibility of dazzling others.
  4. Keep dipped beam on when you have no main beam or could dazzle others; assess visibility again when leaving.

Signalling a lateral movement

Communicate the side and end the warning when you adopt the new course.

  1. Observe and check that you can move while respecting priority rules.
  2. In sufficient time, activate the indicator on the appropriate side or make the prescribed hand signal if you have no indicator.
  3. Maintain the light signal during the movement.
  4. Cancel the indicator when you adopt the new course; signal any subsequent movement separately.

Responding to dazzle

Protect your vision and keep control of the moped.

  1. If you are using main beam and could dazzle others, change immediately to dipped beam.
  2. If you are dazzled, avoid looking directly at the light source as a practical measure.
  3. Reduce your speed as much as necessary, even stopping to avoid a collision with someone ahead.
  4. Keep the required lights on; only restore main beam when its conditions are met and you have passed the oncoming vehicle.

Choosing lights in fog or rain

Distinguish reduced visibility from particularly adverse conditions.

  1. Check whether the conditions significantly reduce visibility.
  2. Switch on position lights and the appropriate front lighting; use dipped beam on your moped without fog lights.
  3. If you have type-approved front fog lights, use them only in their permitted circumstances.
  4. Switch on the rear fog light, if fitted, only in particularly adverse conditions.
  5. Switch off the rear fog light when those conditions disappear and keep any other lights that remain necessary on.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module