Theory · D Licence - Bus · Module 16 of 18

Bus maintenance and checks

You learn to check the bus before service, identify defects in tyres, fluids, visibility and brakes, and decide when you must immobilise it. You distinguish technical checks from ITV (vehicle roadworthiness test) requirements and learn to interpret pressure readings, warnings and faults without applying car rules to a bus.

37 min read25 sectionsReviewed Nov 3, 2026
A person checks the tyre pressure of a bus parked beside the right kerb, with a maintenance compartment open.
Bus checks before service

1Pre-service inspection

A driver wearing a reflective vest and holding a clipboard inspects the front tyre of a bus parked in a depot yard and secured with a chock at the rear wheel.
The key idea

Check your bus before you start service.

TaskWhy you do it
Preventive maintenanceYou prevent deterioration
Daily inspectionYou find faults
RepairYou remove the cause

Remember

  • Use the manual and your company checklist.
  • Check previous fault reports and confirm that you can drive safely.
  • Check outside, your driving position and operation in a safe area.
  • Secure the bus and keep passengers away from danger.
  • Remember: ITV does not replace maintenance or daily checks.
  • Authorised centres check the tachograph and speed limiter.

Exam trap: Wrong: an ITV inspection replaces daily checks and maintenance. Right: keep both up to date and check that your bus is safe.

Read the full explanation
  • You must know the bus you are going to drive: locate its reservoirs, inspection points and emergency controls, and learn what its warnings mean from the manual. Use the company checklist and the manufacturer's procedure; familiarity with another coach does not guarantee that this one has the same layout.
  • Before starting, check the previous service's reported defects and make sure that any outstanding repairs allow the vehicle to be used safely. A report of a brake or steering fault must be clarified and resolved before you authorise the bus to leave.
  • Carry out a complete walk-round, a check of the driver's position and a functional check. Do this in a safe area, with the vehicle secured and no passengers exposed to unexpected movement.
  • Preventive maintenance follows a schedule to prevent deterioration; the daily inspection detects irregularities and repairs remove their cause. You must coordinate inspections with the company according to time, mileage and operating conditions, keeping a record of work and incidents. The ITV (vehicle roadworthiness test) does not replace these tasks.
  • Between scheduled services, the workshop or trained personnel change the engine oil and filters, fuel filter and water separator elements, air filter and belts; renew the coolant and brake fluid where applicable; replace the air dryer cartridge, grease specified points, and rotate and align the tyres where appropriate. You must monitor due dates and report irregularities; only carry out operations authorised by the manual and your training. Intervals and products depend on the bus. Authorised centres carry out the statutory checks on the tachograph and speed limiter: see ‘The bus tachograph’ and ‘Bus dimensions and masses’.

2Systematic exterior walk-round

A person wearing a reflective vest inspects the rear wheel and side of a green two-axle coach parked in a maintenance area.
The key idea

Walk all round your bus to find damage and dangerous objects.

Remember

  • Follow the same route each time; check inner wheels too.
  • Look for loose parts, open catches, damaged windows and exhaust defects.
  • Identify new fluid patches without touching hot parts or tasting fluids.
  • Check nothing rubs against tyres and the bus is not leaning.
  • Clean and check number plates, lights and reflectors.
  • Resolve problems and check your surroundings again before moving.

Exam trap: Wrong: start service with exhaust gases entering the passenger area. Right: report the defect and request repair before service.

Read the full explanation
  • Always follow the same route so that you do not miss the opposite side or the inner wheels. Inspect the bodywork, bumpers, windows, service covers, doors and luggage compartments. Look for loose parts, dangerous sharp edges and closures that could open while driving.
  • Look at the ground beneath the engine and accessible systems without putting yourself at risk. A new stain means you must identify whether it comes from fuel, oil, coolant or another system; water from condensation may have a normal cause. Do not touch fluids on hot components or taste them.
  • Check that the wheel arches are clear, that no parts are rubbing against the tyres and that the bodywork is at its usual height. An unusual lean or an apparently deflated suspension air spring requires inspection. The suspension affects wheel contact and stability.
  • Check that number plates, lights and reflectors are secure and clean. A light that is present but covered in mud cannot perform its practical function. If you see an open cover or an object beside a wheel, deal with the problem and check the surroundings again before moving the bus.
  • Inspect the exhaust from a safe position: look for leaks, loose supports, damaged pipes and deterioration of the silencer. You must ensure that it is securely fastened and that the silencer is intact and effective; if you detect exhaust gases escaping from a joint or entering the passenger compartment, report the defect and request repairs before service. [RGC, art. 7.2](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a7).

3Wheels, rims and tyres

A driver wearing a reflective vest uses a flashlight to inspect a crack and a bulge in the sidewall of the front tyre of a bus parked beside the right-hand kerb.
The key idea

Check the whole tyre, the rim and its fastenings.

Remember

  • Look for bulges, cuts, cracks and exposed cords.
  • Check sidewalls and beads; a slow leak may need valve and rim-seat checks.
  • Request attention if nuts are missing or the rim is cracked.
  • Check the tyre markings against your bus documentation.
  • Remember: TUBELESS means there is no separate inner tube.
  • Leave repairs and removal to staff with suitable equipment.

Exam trap: Wrong: you can use a tyre that holds air and has tread. Right: a damaged tyre needs attention.

Read the full explanation
  • Inspect the tread, shoulders, sidewalls and beads. The tread contacts the ground; the sidewall forms the side of the tyre and the bead seats on the rim. Inspecting only the part that touches the road leaves areas unchecked where cuts, impacts or deformation may appear.
  • Look for bulges, cuts, cracks, layer separation and exposed cords. Also check the rim and its fastenings: a crack, a missing nut or signs of movement require attention. A slow leak may also require checking the valve and the tyre bead seat on the rim.
  • The dimensions and performance must match the approval or an acceptable equivalent; keep the markings legible and avoid tyres with structural damage. [RGV, annex VII](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii). How to read tyre sizes, construction, load indices and speed codes is explained in ‘Bus mechanics’.
  • TUBELESS identifies a tyre without a separate inner tube; it does not state a maximum speed. When replacing it, you must maintain compatibility between the tyre, valve and rim. Do not improvise repairs, removal or retightening: bus wheels require suitable equipment, procedures and personnel.

4Correct cold tyre pressure

A mechanic uses a pressure gauge to check a rear tyre of a bus parked at a depot.
The key idea

Measure tyre pressure using the manufacturer’s guidance and your expected load.

PressureWhat you can cause
Too lowHeat build-up and shoulder wear
Too highChanged road contact and possible centre wear

Remember

  • Check the pressure for your model, axle, wheel arrangement and load.
  • Measure every tyre with a pressure gauge, including inner twin tyres.
  • Use the cold reference when the manufacturer specifies it.
  • Investigate repeated pressure loss; daily inflation does not repair the cause.
  • Check for damage even if you have electronic pressure monitoring.

Exam trap: Wrong: release hot air to match the cold pressure. Right: if correctly inflated cold, leave the air in.

Read the full explanation
  • You must check the recommended pressure for the model, axle, fitment and expected load. There is no single pressure in bar that is correct for every bus. Use an approved and calibrated pressure gauge and check every wheel, including the inner tyre of a twin-wheel fitment; appearance does not replace measurement. [RGV, annex VII, section 6](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • Compare the reading with the cold specification when that is the manufacturer's reference. During a journey, temperature and pressure normally rise. If the pressure was correctly set when cold, do not release air to bring a hot reading down to the reference value: when the tyre cools, it would be underinflated.
  • Underinflation makes the sidewalls work harder and encourages heat build-up, damage, shoulder wear and rolling resistance. Overinflation also changes the contact patch and may encourage central wear.
  • If the pressure keeps dropping, you must investigate the valve, rim and tyre instead of simply inflating it every morning. An electronic monitoring system helps detect problems but does not remove the need to inspect for damage. After correcting an irregularity, follow the check or reset procedure specified for the system installed.

5Bus tyre tread and wear

A mechanic kneeling on the pavement checks a main tread groove on the front tyre of a bus parked beside the kerb using a tread depth gauge.
The key idea

Measure the main tread grooves and check any uneven wear.

1.0 mmMinimum: M2 and M3
1.6 mmMinimum: M1, N1, O1, O2
3,500 kgRegrooving: only vehicles over
Vehicle categoryMinimum main tread depth
M2 and M31.0 mm
M1, N1, O1 and O21.6 mm

Remember

  • Measure main grooves across the tread and around the tyre.
  • Do not always wait for the legal minimum before replacing tyres.
  • Consider rain, overall condition and the manufacturer’s guidance.
  • Report wear location and how it develops so the workshop can correct its cause.
  • Do not deepen the tread of any worn tyre yourself.
  • Regroove only tyres marked Regroovable or the prescribed symbol, on vehicles over 3,500 kg.

Exam trap: Wrong: apply 1.6 mm to your M2 or M3 bus. Right: keep at least 1.0 mm in the main grooves.

Read the full explanation
  • For categories M2 and M3, you must maintain at least 1.0 mm in the main tread grooves. The figure of 1.6 mm applies to M1, N1, O1 and O2. [RGV, annex VII, section 2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii).
  • You must measure with a suitable instrument at different points across and around the tyre, following the criteria for main grooves. An adequate reading in the centre does not rule out dangerous localised wear. Do not confuse the depth of a secondary cut with the depth of the main tread that the regulations require you to check.
  • The legal minimum is not a maintenance target that you should always run down to. When deciding whether to replace a tyre, consider rain, its overall condition and the manufacturer's guidance. Worn tread reduces the tyre's ability to clear water and may impair contact; sufficient tread depth does not make up for incorrect pressure.
  • Uneven wear may point to incorrect pressure, misalignment, imbalance or suspension problems, but you must have the cause confirmed at a workshop. Report where the wear appears and how it develops so the workshop can correct its cause.
  • Regrooving is permitted only on tyres for vehicles with a maximum authorised mass of more than 3,500 kg that bear the word Regroovable or the regulatory symbol. [RGV, annex VII, section 4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii). Have this work carried out by specialist personnel, who must follow the tyre manufacturer's instructions.

6Twin wheels

A maintenance worker checks the pressure of a tyre in a parked bus's dual wheel assembly using a pressure gauge connected to the valve extension at the bottom of the rim.
The key idea

Check each twin tyre separately before you start service.

Remember

  • If one tyre loses pressure, ask for both to be checked before service.
  • Use paired tyres with compatible sizes, construction and wear.
  • Check the pressures specified for the wheel arrangement.
  • Look for rubbing; remove trapped objects using a safe procedure.
  • Never put your hands between tyres while the bus is moving.
  • Follow the load ratings for twin-wheel use.

Exam trap: Wrong: continue with a faulty twin tyre because another remains. Right: report it and request attention before service.

Read the full explanation
  • You must check each of the two tyres in a pair separately. The inner tyre may be deflated even when the outer one appears to support the bus. If one loses pressure, its partner is subjected to abnormal stress; ask for both tyres to be checked before continuing the service.
  • Check that the pair is compatible in dimensions, construction and wear, and that the pressures are suitable for the fitment. Significant differences in effective diameter or inflation distribute the load unevenly and encourage heat build-up. You need suitable access to both valves to check them without loosening or damaging them. [DGT, Manual VIII, twin-wheel fitment](https://sede.dgt.gob.es/.galleries/permisos-de-conducir/certificacion-aptitud-profesores-formacion-vial/2024/Manual-VIII-Mecanica-2024.pdf).
  • Look at the space between the twin wheels: remove foreign objects using a safe procedure and look for signs of rubbing between the sidewalls. A trapped stone can damage the tyres or be thrown out. Do not put your hands there while the bus is moving or stand where you could be trapped.
  • Do not work out the capacity of the fitment simply by adding the ratings for single wheels. You must comply with the ratings for twin-wheel fitment and the vehicle requirements. If you find a mismatched pair or a damaged tyre, report the defect and request the required intervention before the bus enters service.

7Precautions when removing and fitting wheels

A mechanic handles the removed front left wheel of a bus, with chocks in front of and behind the diagonally opposite rear right wheel.
The key idea

Change wheels only with training, suitable equipment and the manufacturer’s procedure.

Remember

  • Choose firm, level ground away from traffic; without protection, request assistance.
  • For roadside breakdowns, use hazards and connected V-16; wear your vest before working outside.
  • Apply the parking brake and chock the diagonally opposite wheel.
  • Loosen nuts slightly on the ground; remove them after lifting.
  • Use the specified lifting point; never go underneath with only a jack.
  • Tighten nuts crosswise and check torque as the manufacturer specifies.

Exam trap: Wrong: improvise inflation of heavy twin wheels or multi-piece rims. Right: you need specialist staff and protective equipment.

Read the full explanation
  • To change a wheel, you need training, tools and equipment suitable for the bus. Park it on firm, level ground away from traffic; if it breaks down on the road, switch on the hazard warning lights, use the connected V-16 beacon and put on your reflective vest before working outside. If you cannot work safely, call for assistance. [RGC, art. 118.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a118) and [art. 130.4](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130).
  • Apply the parking brake and place chocks against the wheel diagonally opposite the one you are removing, following the manufacturer's procedure. Loosen the nuts slightly while the wheel is on the ground; finish removing them after raising it.
  • Position a jack of adequate capacity only at the lifting point specified by the manufacturer. Never get under a bus supported only by a jack; air suspension also requires its safety supports. Raise it only as far as necessary and get help or use a wheel handling device to control its weight without trapping anyone.
  • When fitting the wheel, check that it is seated correctly and that the fixings are secure, then tighten the nuts in a cross pattern. Carry out the final tightening with the appropriate tool, to the specified torque and under the specified support conditions. Check the torque again after the first few kilometres, at the time specified by the manufacturer; do not invent a universal torque or distance.
  • On twin wheels, position the valves so that they remain accessible as intended by the fitting arrangement. Inflating heavy twin assemblies or wheels with detachable rim rings requires protective equipment, such as a safety cage, and specialist personnel; do not remove rim rings under pressure or improvise inflation at the roadside.

8Chains and winter equipment

A coach parked in a lay-by beside a road with snow on the verges has snow chains on the wheels on both sides of its rear drive axle.
The key idea

Distinguish general chain rules from special requirements for driving in snow.

3,500 kgWinter restrictions: maximum mass above
4 mmRed level: winter tyre tread
16 × 16 cmRed-level identification sign
CaseEquipment you must check
General minimum if you choose chainsOne driven wheel on each side; prescribed special tyres are an alternative where applicable
Winter restrictions: maximum authorised mass over 3,500 kg3PMSF or POR tyres, at least on steering and driven axles
Buses: exceptional red-level arrangementsAll wheels: 3PMSF winter tyres, at least 4 mm in main grooves; seat belts at every seat; visible 16 × 16 cm sign; geolocation when instructed; prior sworn declaration (declaración responsable) to the DGT

Remember

  • Identify the driven wheels before fitting chains.
  • Check size, compatibility and clearance; practise fitting chains away from traffic.
  • Identify special snow tyres by M+S, M&S or M.S together with 3PMSF.
  • Distinguish winter restrictions from exceptional red-level conditions.
  • For red-level travel, submit your sworn declaration (declaración responsable) to the DGT beforehand.
  • Send your geolocation through the provided app when the driving instructions require it.

Exam trap: Wrong: chains let you drive your bus under red-level conditions. Right: you need 3PMSF winter tyres on all wheels, at least 4 mm in the main grooves, seat belts at every seat, a 16 × 16 cm sign visible from outside, a prior sworn declaration (declaración responsable) to the DGT, and geolocation through its app when driving instructions require it.

Read the full explanation
  • If you choose approved chains or anti-skid devices, the general minimum is one driven wheel on each side. Where applicable, you may use the prescribed special tyres as an alternative. [RGV, art. 12.5.2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a12). Identify the axle that receives power from the engine.
  • Check the chains' compatibility, condition, size and available clearance in advance. Practise fitting them in a safe area and follow the instructions on tensioning, speed and removal. Do not fit them next to traffic if you cannot work safely, and do not assume they fit every twin wheel.
  • To identify the special snow tyre in Annex VII, check for the M+S, M&S or M.S marking together with the 3PMSF pictogram. [RGV, Annex VII, section 5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii). Do not rely on the tread pattern's appearance alone.
  • To comply with winter mobility restrictions for vehicles with a maximum authorised mass (MMA) over 3,500 kg, you must fit 3PMSF or POR certified tyres at least on the steering and driven axles. [RGV, Annex VII, section 5](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anvii). Distinguish this requirement from the exceptional rules for travelling under a red level alert.
  • To travel exceptionally under a red level alert, your bus must have a complete set of special winter tyres on every wheel, marked 3PMSF and with at least 4 mm of tread in the main grooves. It must have a seat belt at every seat and the prescribed 16 × 16 cm label visible from outside. You must submit the declaración responsable (declaration of compliance) to the DGT in advance and send your geolocation using the app it provides when traffic instructions require this. [DGT, exceptional travel under a red level alert](https://sede.dgt.gob.es/en/movilidad/autorizaciones-especiales/circulacion-con-nivel-rojo/index.html).

9Oil: checking and topping up

A mechanic checks the oil dipstick beside the open rear engine of a bus parked on level ground and holds a white cloth in the other hand.
The key idea

Measure and top up oil as your bus manual instructs.

Remember

  • Measure on level ground; follow the specified engine condition and waiting time.
  • Wipe the dipstick, insert it correctly and read it again.
  • Keep the level between the marks; never exceed the maximum.
  • Add small amounts of the specified oil when needed.
  • Check leaks and record top-ups; these do not replace oil and filter changes.
  • Choose the viscosity and approvals specified by the manufacturer.

Exam trap: Wrong: always measure with a cold engine. Right: follow your manufacturer’s specific procedure.

Read the full explanation
  • Check the level on level ground; a slope can give a false reading. If you use a dipstick, follow the instructions for engine condition and waiting time so that the oil can drain back. Do not always insist on a cold engine: some procedures require you to warm it up and wait, while others use electronic measurement.
  • With a dipstick, wipe it clean, insert it fully and take another reading as described in the manual. Keep the level between the marks and, if necessary, add small amounts of the specified product. Do not fill above the maximum or add oil simply because a warning light has come on before identifying what it means.
  • Also check for leaks and abnormal consumption, and record any top-ups. Topping up maintains the quantity, but does not replace changing the oil and filter or repair a leak.
  • Select the viscosity and manufacturer approvals specified by the manufacturer; viscosity grades and oil selection are explained in the “Bus mechanics” module.

10Coolant and temperature

A driver waits beside a bus stopped by the kerb, with the engine compartment open and the expansion tank cap closed as vapour rises from the engine area.
The key idea

Check coolant and stop safely if your engine overheats.

Remember

  • Check level and leaks as instructed, usually with the system cold.
  • Never open a hot pressurised cooling cap: you could be burnt.
  • Use the specified product and concentration; colour does not guarantee compatibility.
  • Do not permanently replace the specified coolant with water.
  • Do not improvise by pouring cold fluid onto an overheated engine.
  • Keep clear of fans and belts: they can start unexpectedly.

Exam trap: Wrong: rev the engine or remove the thermostat to continue after overheating. Right: stop safely and follow the manual.

Read the full explanation
  • Check the level in the expansion tank, if fitted, under the specified conditions, usually with the system cold. Keep it within the marked range and check accessible hoses, clamps and signs of leaks. A sealed circuit still needs monitoring: sealed does not mean it can never lose fluid.
  • Do not open the cap of a hot, pressurised system: steam and hot fluid can burn you. Let it cool according to the procedure, and do not improvise by pouring cold fluid over an overheated engine. Keep clear of fans and belts, which may start unexpectedly.
  • Use coolant with the correct specification and concentration, including protection against temperatures below zero. Colour does not guarantee that two products are compatible. Do not permanently replace the specified mixture with water or assume antifreeze is useful only during snowfall.
  • An abnormal rise in temperature may be caused by a low level, leaks, the pump, thermostat, fan or pump drive, depending on the design. If the engine overheats, stop safely and follow the manual. Do not decide that revving the engine or removing the thermostat is enough to continue with passengers.

11Other fluids and consumables

A mechanic consults a manual with drawings and points to the closed cap of a reservoir in the maintenance compartment of a bus parked beside the right-hand kerb.
The key idea

Identify each system and use only its specified fluid.

Your bus systemWhat you must check
Hydraulic steeringLevel and leaks as the manual instructs
Fully electric steeringThere may be no hydraulic reservoir
Brakes using fluidLevel, leaks and replacement schedule
Air brakesAir reserve

Remember

  • Identify the reservoir before opening it.
  • For a hydraulic clutch, top up through its filler, never the bleed nipple.
  • Investigate repeated level drops; topping up does not prove a repair.
  • Plan fuel and emissions reagent supplies, where used; never confuse their fillers.
  • Check filters according to use and manufacturer guidance.

Exam trap: Wrong: look for fluid in every brake system. Right: with air brakes, check the air reserve.

Read the full explanation
  • Identify the reservoir before opening it. For hydraulic power steering, check the level and possible leaks under the conditions in the manual; do not confuse it with coolant or brake fluid. Fully electric steering may not have this reservoir, so not every check applies to every model.
  • If the clutch has hydraulic control, check its reservoir when required and use the fluid specified on its filler cap. The bleed nipple is not a filling point. A repeated drop in level or difficulty selecting gears requires diagnosis; topping up does not prove that the cause has been repaired.
  • In systems with brake fluid, check the level, leaks and the specified replacement schedule. Do not add an incompatible product or open the circuit unnecessarily. With air brakes, by contrast, you must check the air supply: do not look for a hydraulic reservoir that the system does not have.
  • Plan for fuel and, if the vehicle uses it, the emissions system reagent. Do not mix up their filler openings or ignore range warnings. Check filters according to use and the manufacturer's instructions; a blocked air filter can contribute to loss of power or smoke, but do not diagnose the fault by colour alone.

12Clean and checked lights

A helper wearing a reflective vest cleans a rear light on a parked bus with a wheel secured by a chock.
The key idea

Check all fitted lights work, stay clean and point correctly.

Device, where applicableWhat you check it shows
End-outline marker lamps (luces de gálibo)Width from high positions
Side marker lampsThe side of your bus

Remember

  • Secure the bus before checking lights from outside.
  • Use help or a safe method to check rear lights; test the horn too.
  • Look for broken lenses, moisture and loose parts.
  • Check colours and connections; changing a bulb may not solve the fault.
  • If a fault reduces lighting, adjust your speed to the available range.
  • Arrange repairs in a safe place.

Exam trap: Wrong: accept a weak or intermittent horn. Right: it must sound continuously, evenly and loudly enough; request repair if faulty.

Read the full explanation
  • Check that the headlights, position lights, direction indicators, hazard warning lights, brake lights, reversing lights and number plate lights work and are clean, along with any other fitted devices. Ask someone to help or use a safe method to check the rear. Do not leave a vehicle unsecured while you stand outside to observe its lights.
  • Inspect the light units from different angles and look for cracked lenses, moisture or loose parts. Check that a repair has not changed the colour or covered the surface. A faulty connection can cause several lights to work incorrectly; replacing a bulb does not always solve the problem.
  • Also check the end-outline marker lamps and side position lamps where fitted to the bus. End-outline marker lamps show the vehicle's width from high points; side position lamps make its side visible. Installation and use requirements are covered in the “Bus lighting and signs” module; here, check that the devices fitted to the bus work correctly. [RGV, Annex X, section 1](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anx).
  • Keep the beam alignment correct: aiming too low reduces the range, while aiming too high can dazzle. If the relevant lighting is disabled or suffers an irreparable fault during a journey and this forces you to use a light of lower intensity, reduce your speed until you can stop the bus within the area lit. [RGC, art. 107](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a107). Arrange for the repair to be done in a safe place.
  • Test the horn briefly in a suitable place: it must produce a continuous, steady sound of sufficient intensity. If it sounds intermittent or weak, or does not respond, record the fault and arrange a repair. The functional check must respect the conditions in the surroundings. [RGV, art. 11.7](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a11).

13Mirrors and field of vision

A driver seated at the wheel of a bus stopped beside the right-hand kerb adjusts the exterior mirror control, with mirrors visible on both sides of the windscreen.
The key idea

Check the compulsory mirrors on M2 and M3, then adjust every mirror before setting off.

Remember

  • Check M2 and M3’s two compulsory class II mirrors, one left and one right.
  • Check any other mirrors fitted to your bus.
  • Adjust your seat first, then your mirrors.
  • Clean mirrors; check mountings, adjustment and demisting where fitted.
  • Keep your view clear and keep checking surroundings; mirrors do not remove blind spots.
  • Vision aids are explained in “Safe bus driving”.

Exam trap: Wrong: use an interior mirror instead of a compulsory main mirror. Right: M2 and M3 need class II main mirrors on both sides.

Read the full explanation
  • Check the two class II main mirrors compulsory on M2 and M3, one on the left and one on the right, and any others fitted to your bus. [RGV, Annex III](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#aniii). The use of vision aids is explained in “Safe bus driving”.
  • You must adjust the seat and mirrors before starting the service. Clean the surfaces and check the mountings, adjustment and demisting where provided. A mirror that vibrates or folds in unintentionally reduces the information available, even if the glass is not broken; report the fault and restore it to working order.
  • Check any cameras and assistance displays fitted to the vehicle and understand which areas they cover. A frozen image or dirty lens can lead you to think the side is clear. Use the system in accordance with its approval and manual, without improvising replacements for mandatory equipment.
  • From your actual driving position, check that accessories, curtains and objects do not obstruct your field of vision. You must continue checking your surroundings while driving: correctly adjusted mirrors do not eliminate blind spots. Observation techniques when turning or approaching a stop are covered in “Safe bus driving”.

14Windscreen, wipers and washer system

A driver cleans the windshield of a green coach parked beside the right-hand kerb using a long-handled squeegee.
The key idea

Keep your windscreen clean and check that you can see clearly.

Remember

  • Clean glass inside and outside; check damage and reflections.
  • Check ventilation, heating and demisting outlets.
  • Replace hardened, cracked or streaking blades; repair damaged holders too.
  • Fill washers with a suitable product and check the jets.
  • Free blades stuck to ice; avoid repeated wiping on dry glass.
  • If you cannot maintain enough visibility, find a safe place to stop.

Exam trap: Wrong: continue because you can see through a narrow strip. Right: you need enough visibility to continue.

Read the full explanation
  • You must check the windscreen inside and out: dirt, misting, reflections and damage can prevent you from seeing even when the wipers work. Keep the demisting vents clear and check the ventilation and heating. Do not try to solve poor visibility by driving closer to the vehicle in front to follow its lights.
  • Check that the wipers sweep correctly and that the rubber remains flexible. If it has hardened, cracked or leaves streaks, replace the appropriate part; if the arm is damaged, repair that too. Do not wait for it to break or apply a universal six-month replacement interval regardless of its condition and the manufacturer's guidance. [DGT, winter test](https://revista.dgt.es/es/test/test-especial-invierno-n223.shtml).
  • Fill the windscreen washer reservoir with a product suitable for the system and the expected temperatures, and check the jets. Do not confuse this reservoir with the expansion tank. Avoid repeatedly operating the wipers on dry or frozen glass, and free stuck wipers before moving them.
  • Test the system in conditions that will not damage the glass or rubber, and check its sweep. If it stops or cleans poorly during a journey and you cannot maintain sufficient visibility, find a safe place to immobilise the bus.

15Doors and passenger compartment fittings

A driver checks the open door and clear steps of a bus stopped at the right-hand kerb from the pavement.
The key idea

Check doors, access routes and emergency equipment before carrying passengers.

Remember

  • Test opening, closing and warnings with the area clear.
  • If a door-open warning appears, check the door is actually closed.
  • Check seats, fitted seat belts and covers; keep access routes clear.
  • Check your suitable approved extinguisher, its accessibility and maintenance.
  • Carry connected V-16 and a vest; this annex does not require a spare wheel.
  • Keep catches and safeguards working; heat may require stopping, depending on passengers’ condition.

Exam trap: Wrong: drive with doors open to reduce heat. Right: do not disable catches or safeguards.

Read the full explanation
  • You must check the doors open and close and that their warnings work, following the vehicle procedure and keeping the area clear. Check that there are no objects in the mechanisms or on the steps. A door-open warning means you must check that the door is actually closed; do not cover the warning light or bypass the system.
  • Check the position and fastening of interior panels and compartments, as well as the condition of any parts that could come loose. Check the fitted seat belts, seats and access points without turning this check into an improvised repair. Cleaning also helps you spot damage and objects obstructing the way.
  • You must carry approved fire-extinguishing equipment that is suitable and ready for use, as well as a connected V-16 beacon and a high-visibility reflective vest. [RGV, Annex XII, section 2](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#anxii). Check that the emergency equipment is accessible and maintained; its use and evacuation are covered in “Passenger safety and emergencies”. Under this annex, the bus is not required to carry a spare wheel.
  • If the air conditioning fails, you must assess and resolve the problem or reorganise the service safely. Keep door catches and safeguards working; the interior temperature may require stopping the service depending on passengers' condition.

16Coupling and articulation

A person wearing a reflective vest checks the coupling between a coach and a small trailer, with the safety chain and electrical cable connected and the wheels secured with chocks.
The key idea

Check your trailer coupling and connections as the manufacturer instructs.

1,500 kgSecondary coupling: maximum authorised mass
CaseWhat you must check
Bus with an authorised trailerCoupling, locking mechanism and connections for the combination
Articulated busArticulation as instructed; do not uncouple it during daily inspection

Remember

  • With an authorised trailer, check the coupling, locking mechanism and safety parts.
  • Check electrical and brake connections where fitted.
  • Prevent cables and pipes becoming tight, trapped or dragged when turning.
  • Before uncoupling, secure each vehicle with the specified supports and chocks.
  • Afterwards, check trailer lights and brakes where fitted.
  • On articulated buses, check bellows, interior gangway and warnings using the manual.

Exam trap: Wrong: every trailer needs the same secondary coupling. Right: check it for maximum authorised mass of 1,500 kg or less without automatic braking on coupling failure. It must keep the drawbar off the ground and retain some trailer guidance.

Read the full explanation
  • If the bus is towing an authorised trailer, you must check the coupling, the locking mechanism and the safety components provided for that combination. Check for wear, secure mountings and visible damage. The connection must be confirmed using the manufacturer's procedure, not judged by the fact that the drawbar appears to have entered.
  • Connect and check the electrical connections and, where fitted, the braking connections, following their identification. Make sure that pipes or cables are not stretched, trapped or dragged when turning. Do not assume that every light trailer has pneumatic connections like a heavy vehicle.
  • If the trailer does not have automatic braking if the coupling breaks, check the secondary coupling: it must prevent the bar from touching the ground and retain some control of the trailer. This requirement applies to trailers with an MMA of 1,500 kg or less and includes the authorised light trailer used with a category D licence. [RGV, art. 13.4](https://www.boe.es/buscar/act.php?id=BOE-A-1999-1826#a13).
  • Before uncoupling, secure the vehicles separately and use the supports and chocks provided to prevent movement. Keep the crush zone clear. The subsequent functional check includes the trailer lights and brakes where fitted; checking the mechanical connection does not check the other systems.
  • On an articulated bus, visually check the bellows, interior passage, warnings and accessible components in accordance with the manual. Do not treat its articulation as a trailer that you can uncouple during the daily walk-round. If you notice abnormal play, rubbing or warnings, request an inspection without handling protective mechanisms.

17Brake check

A driver holds an inspection sheet while a mechanic uses a flashlight to inspect the front wheel of a bus parked in a maintenance area.
The key idea

Check your brakes before service; do not set off if braking is impaired.

Remember

  • Check service brake, parking brake and warnings as the manual instructs.
  • Test while moving only in a controlled area without endangering anyone.
  • Watch response, control travel, pulling, noises, vibrations and smells.
  • Investigate an unusually hot wheel; never touch discs or drums.
  • Check maintenance is up to date; look for leaks and damaged fastenings.
  • Keep scheduled checks: your daily test does not replace them.

Exam trap: Wrong: finish the route slowly despite poor braking. Right: do not set off with impaired braking.

Read the full explanation
  • You must check the service brake, parking brake and warnings before starting service, in accordance with the manual. If you carry out a moving test, use a controlled area, travel at an appropriate speed and do not endanger anyone. Do not make a hard stop with passengers on board to find out whether the system works.
  • Observe the response, control travel and any tendency to pull to one side, as well as abnormal noises, vibrations or smells. A brake that responds late or an excessively hot wheel needs investigation. Avoid touching discs or drums: they can cause burns even after the vehicle has been stationary for a while.
  • Check that maintenance on the fitted braking system is up to date and that accessible areas show no leaks or damaged mountings; the mechanisms, controls and bleeding procedures are explained in “Bus brakes and retarders”.
  • If you find that braking effectiveness is compromised, report the fault and take the bus out of service until it is repaired. Record which test revealed it, whether it affected one side and which warnings accompanied the symptom, to help the workshop diagnose it.

18Air reserve and leak-tightness

A bus driver stopped beside the right-hand kerb looks at two pressure gauges with their needles in the orange zone and an illuminated orange warning light on the dashboard.
The key idea

With air brakes, check sufficient air and no abnormal leaks.

Remember

  • Check your manufacturer’s pressures and indications; there is no universal figure.
  • Check the circuits and that warnings clear normally.
  • Listen for leaks without approaching moving parts.
  • Request repairs for persistent leaks or abnormal pressure drops.
  • Follow the maintenance schedule for the dryer and drains.
  • Leave work on valves or pressurised circuits to trained staff.

Exam trap: Wrong: set off with low air because the engine works well. Right: never start driving with insufficient pressure.

Read the full explanation
  • On a bus with pneumatic brakes, you must check the air reserve and that the warnings clear normally, following the procedure. There is no single starting pressure that is valid for every model: identify the areas and indications specified by the manufacturer, and do not set off with insufficient pressure.
  • Check the available circuit readings and listen for possible leaks without going near moving parts. A persistent leak or abnormal pressure drop requires repair. A sufficient reading on a pressure gauge does not, by itself, prove that all circuits and warning devices are working correctly.
  • Check that the scheduled maintenance for the dryer and manual or automatic drains has been carried out; their operation is explained in “Bus brakes and retarders”.
  • After the prescribed test, record the pressure reached, the observed charging time and any warnings or leaks detected so the workshop can reproduce the symptom. Work on valves or pressurised circuits must be carried out by trained personnel; the procedure depends on the system installed.

19Warning lights and self-checks

A bus driver turns the ignition key with the vehicle stopped beside the right-hand kerb and the oil pressure warning light illuminated on the dashboard.
The key idea

Use the manual to understand warnings and act on serious faults.

Remember

  • Watch ignition self-checks and warnings that remain after starting.
  • Learn symbols: colour guides you, but the manual tells you what to do.
  • For minimum oil pressure warnings with the engine running, stop safely and switch off.
  • A correct oil level does not rule out a lubrication fault.
  • Act on intermittent warnings too; clearing them does not repair the cause.
  • A charging warning does not prove your battery is empty.

Exam trap: Wrong: top up oil and keep running after a minimum oil pressure warning. Right: with the engine running, stop safely and switch it off.

Read the full explanation
  • You must observe the self-check sequence when you switch on the ignition and check which warnings remain when you start the engine. A warning light that is off only provides information if its circuit works. Learn the symbols used in your model: the colour indicates priority, but the exact action depends on the message and the manual.
  • If the minimum oil pressure warning remains on or appears while the engine is running, you must stop safely and switch off the engine. Pressure and level are different things: a correct oil level reading does not rule out a lubrication fault.
  • If a cooling system, brake pressure or serious steering fault warning comes on, act according to the manual and the safety of your surroundings. Simply clearing the message or switching the ignition off and on is not enough. An intermittent warning also needs attention; its disappearing when you accelerate does not prove that the fault is fixed.
  • A charging warning light that stays on while the engine is running may indicate a fault in the charging system or its circuit. It does not automatically mean that the battery is flat, nor does it identify a specific faulty part. If it occurs with other symptoms, assess the system as a whole and call for assistance where appropriate.

20ABS, electrical systems and recurring faults

A driver seated on the left of a bus parked in a depot looks at the illuminated amber ABS warning light beside an open fuse box containing fuses and a spare of the same colour and size.
The key idea

Act on ABS warnings and avoid improvised electrical repairs.

Remember

  • Check the ABS warning sequence as the manual instructs.
  • Request diagnosis for recurring ABS faults, even if restarting clears the warning.
  • Use the specified fuse type and amperage; investigate repeated failures.
  • Follow battery procedures to avoid sparks and short circuits.
  • On electric or hybrid buses, leave high-voltage work to qualified staff.

Exam trap: Wrong: increase fuse amperage or bypass it to make it last. Right: use the specified type and amperage; investigate repeated failures.

Read the full explanation
  • You must check the ABS and other assistance system warnings according to their intended sequence. If any remain on, note the message and check the manufacturer's instructions before deciding whether to set off.
  • A recurring ABS fault needs diagnosis even if it disappears when you switch the ignition off and on. The system's function and how it responds during braking are explained in ‘Bus brakes and retarders’.
  • If a fuse blows, identify the circuit and use the specified type and rating. A fuse protects against overcurrent; it does not regulate voltage. Do not bridge it with wire or fit a higher-rated fuse to make it last: if it blows again, you must find the cause.
  • Check accessible batteries only using the specified procedure and protection; avoid sparks and short circuits. Do not improvise jump-starts or disconnect systems to clear warnings. Do not handle high-voltage components in electric or hybrid buses: limit your intervention to the driver's role and call a qualified technician.

21Finding faults and carrying out minor repairs

A technician consults a manual beside the open engine compartment of a parked bus secured with wheel chocks, with no passenger door on its visible left side.
The key idea

Use the manual to find causes and repair only within your abilities and equipment.

Remember

  • Secure your bus and record symptoms, warnings and circumstances.
  • Check simple, accessible causes as the manual instructs.
  • Isolate or disconnect as instructed before working.
  • Replace accessible fuses or bulbs only if permitted; check operation afterwards.
  • Visually check accessible belts with the engine stopped and unexpected starting prevented.
  • Request assistance for dangerous or recurring faults, or work beyond your equipment.

Exam trap: Wrong: a simple repair lets you leave without checking. Right: resume service only when safety is restored.

Read the full explanation
  • With the bus secured, note the symptom, warning light and circumstances in which it appears. Consult the manual and identify the affected system: electrical supply, starting, cooling, lubrication or brake air system.
  • First check simple, accessible causes: the position of the battery master switch, fuses, visible connections, fluid levels and air pressure. Isolate or disconnect a system before working on it only as instructed by the manual; do not handle hot, pressurised or high-voltage circuits.
  • Prepare the vehicle's tools and the correct replacement part. You may replace a fuse with its puller or an accessible bulb using the specified tool if the manual allows it; disconnect the specified power supply and then check that it works. Fuse selection is explained in ‘ABS, electrical systems and recurring faults’.
  • With the engine stopped and no risk of it starting unexpectedly, you may visually check an accessible belt as instructed by the manual. A damaged or loose belt needs the specified repair; do not bring your hands or tools near it to test it while the engine is running.
  • Call for assistance if the fault affects the brakes, steering, lubrication or high-voltage system, involves a dangerous leak, returns after a simple repair or requires equipment you do not have. Report what you observed and checked; resume service only when safety has been restored.

22Signs of a fault while driving

A driver holds a bus steering wheel with both hands while travelling in the right-hand lane beside the shoulder, with grey smoke coming from the rear.
The key idea

Act on new symptoms and stop if they could threaten safety.

Remember

  • Watch noises, vibrations, smells, power, temperature and pressure.
  • If you suspect a puncture, slow down smoothly and avoid sudden manoeuvres.
  • Do not automatically blame the road surface for wheel-related vibration.
  • For fuel leaks or signs of fire, stop and protect people.
  • Report symptoms and circumstances; record incidents without distracting yourself while driving.
  • Avoid roadside dismantling that needs workshop equipment or special tools.

Exam trap: Wrong: identify a fault only by smoke colour. Right: gather the symptoms and request diagnosis.

Read the full explanation
  • Pay attention to new noises, vibrations, loss of power, the smell of fuel or burning, and changes in temperature or pressure. A combination of symptoms can help identify the problem, but does not replace a diagnosis. Stop safely if the fault could affect control or cause serious damage.
  • A vibration linked to the wheels can have various causes and should not automatically be blamed on the road surface. If you suspect a puncture or tyre damage, avoid sudden manoeuvres and slow down in a controlled way until you reach a safe place.
  • If you see unusual smoke, do not identify a specific fault from its colour alone. Black diesel smoke may indicate poor combustion due to insufficient air or incorrect fuel delivery, among other causes. A fuel leak or signs of fire mean you must stop and protect people; see ‘Passenger safety and emergencies’ for evacuation.
  • Report symptoms, messages and circumstances to the person in charge and the assistance service. Record the incident without allowing it to distract you while driving, and avoid dismantling parts on the road. Limit your intervention to checks allowed by the manual and refer tasks requiring specific equipment or training to a workshop.

23Breakdown immobilisation

A coach is stopped in a lay-by beside a road, with an orange beacon lit on its roof, hazard lights flashing and passengers seated inside wearing seat belts.
The key idea

Warn others about your breakdown and protect occupants while requesting assistance.

Remember

  • Pull over if safe; use hazard warning lights. Never force a serious fault.
  • Use position lights and end-outline marker lamps (luces de gálibo) where needed.
  • Before service, check your connected V-16 is accessible and has sufficient power.
  • Check you can reach your vest from your seat before getting out.
  • Request assistance; give your location and details of passengers needing support.
  • Do not transfer passengers beside open traffic lanes without safe conditions.

Exam trap: Wrong: activating V-16 requests help. Right: it warns others, but you must request assistance.

Read the full explanation
  • If you can pull over safely, reduce your exposure to traffic and remove the obstruction as soon as possible; use the breakdown warning procedure described in ‘Precautions when removing and fitting wheels’ and, where required, switch on the position lights and end-outline marker lamps. [RGC, art. 130](https://www.boe.es/buscar/act.php?id=BOE-A-2003-23514#a130). Whether you can move the bus depends on whether it remains safe to drive; a serious fault requires assistance.
  • Before service, check that the connected V-16 beacon is accessible, has enough power and can be attached at the designated point on the bus. Its placement and use during a breakdown are explained in ‘Accidents and assistance’.
  • Check that the reflective vest is accessible from the driver's seat so that you can put it on before getting out; safe exit and protection while waiting are explained in ‘Accidents and assistance’.
  • Call for assistance and say that it is a bus, give its location and say whether you are carrying passengers who need support. The beacon warns other road users; it does not replace calling for help. To arrange a safe transfer, see ‘Passenger safety and emergencies’.

24ITV (vehicle roadworthiness test): bus inspection schedule

A driver and a mechanic review a calendar beside a bus parked outside a workshop, with its left side visible and no passenger doors on that side.
The key idea

Check your ITV expiry date and coordinate inspections with your company.

five yearsAnnual ITV through this age
Age: ordinary M2 or M3 busWhen you need ITV
Up to and including five yearsEvery year
Over five yearsEvery six months

Remember

  • Check your ITV expiry date before service.
  • Arrange the pre-inspection maintenance check with your company.
  • Report defects and compare recorded repairs with outstanding faults.
  • Allow enough time for the workshop to check your bus.
  • After inspection, confirm the person responsible has received the report.
  • Check the next inspection date is in the maintenance schedule.

Exam trap: Wrong: an ITV appointment resolves defects. Right: coordinate checks and repairs with your company.

Read the full explanation
  • Check the ITV expiry date when preparing for service: for M2 and M3 vehicles, inspections are annual up to and including five years of age, then every six months. [RD 920/2017, art. 6.1](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a6). How to calculate the vehicle's age, bring an inspection forward and prepare the documents are explained in ‘Bus and passenger transport documentation’.
  • Arrange a pre-inspection check with the company and report defects found during your rounds. Compare recorded repairs with outstanding faults: an ITV appointment does not fix a leak, a damaged tyre or a faulty light. Allow enough time for the workshop to check the vehicle.
  • Before collecting the bus after its inspection, check that the person in charge has received the report and added the next inspection date to the maintenance schedule. Keeping the report and displaying the V-19 sticker are explained in ‘Bus and passenger transport documentation’. [RD 920/2017, art. 10](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a1-2).

25ITV (vehicle roadworthiness test): results and repairs

A mechanic checks the pressure of a bus’s front tire at a workshop while a supervisor holds a sheet with pictograms of a wheel and a light.
The key idea

Read your ITV report and check repairs before returning to service.

Remember

  • Read the defects; confirm with the person responsible whether you can use the bus.
  • Give the workshop all defects and your observations from service.
  • Identify completed work and checks still needed.
  • Check that the cause is removed and the system works correctly.
  • Repeat the necessary daily checks before returning to service.
  • Coordinate repair, transport and any reinspection according to your report’s result and deadline.

Exam trap: Wrong: replacing a part proves the problem is solved. Right: check the cause is removed and the system works correctly before service.

Read the full explanation
  • Read the defects listed in the report and check with the person in charge whether the result allows you to use the bus; the favourable, unfavourable and negative classifications and their effects are covered in “Bus and passenger transport documentation”. [RD 920/2017, arts. 9 and 11](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a1-3).
  • Give the workshop the full list of defects and your observations from the service. Confirm what work has been done and which checks are still outstanding; verify that the cause of the defect has been eliminated and that the system is working correctly again. Repeat the relevant daily checks before returning the bus to service.
  • Coordinate the repair, transfer and any subsequent inspection according to the result and the deadline in the report; the permitted movements, means of transfer, deadlines and choice of inspection station are explained in “Bus and passenger transport documentation”. [RD 920/2017, art. 11](https://www.boe.es/buscar/act.php?id=BOE-A-2017-12841#a1-3).

Pre-departure walk-round

Follow the same order and do not set off with a defect that compromises safety.

  1. Check for reported problems and secure the bus in the inspection area.
  2. Walk round the front, one side, the rear and the other side: check the bodywork, wheels, leaks, exhaust and its mountings and silencer, lights and closures.
  3. Check fluid levels under the measurement conditions specified by the manufacturer.
  4. Adjust your driving position and check mirrors, windows, washers, doors and the horn.
  5. Check the self-test, air pressure and brake operation according to the manual.
  6. Record and report defects; confirm they have been resolved before the bus enters service.

Check wheel pressure and condition

Inspect every tyre, including the inner tyres in twin-wheel assemblies.

  1. Find the specification for each axle, load and wheel arrangement.
  2. Inspect the tyre, rim and fixings, and measure tread depth at several points.
  3. Measure pressure when cold with suitable equipment, reaching every valve.
  4. Adjust to the specification; do not deflate a hot tyre to match the cold-pressure reference.
  5. Investigate leaks, unevenness and damage before approving the wheel.

Serious warning during service

Protect people and avoid making the fault worse.

  1. Identify the warning without losing attention to traffic, and prepare to stop safely.
  2. Pull over and secure the bus if you can do so safely; if oil pressure is insufficient, switch off the engine.
  3. Warn others using the hazard warning lights, any other appropriate lights and the connected V-16.
  4. Protect passengers according to whether a safe exit and refuge are available.
  5. Call for assistance, report the symptoms and do not resume service while the safety defect remains unresolved.

Finished this module?

Mark it as read and you will see your progress on the theory list.

Next module